-
1 водная эрозия
водная эрозия
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
water erosion
The breakdown of solid rock into smaller particles and its removal by water. As weathering, erosion is a natural geological process, but more rapid soil erosion results from poor land-use practices, leading to the loss of fertile topsoil and to the silting of dams, lakes, rivers and harbours. There are three classes of erosion by water. a) Splash erosion occurs when raindrops strike bare soil, causing it to splash, as mud, to flow into spaces in the soil and to turn the upper layer of soil into a structureless, compacted mass that dries with a hard, largely impermeable crust. b) Surface flow occurs when soil is removed with surface run-off during heavy rain. c) Channelized flow occurs when a flowing mixture of water and soil cuts a channel, which is then deepened by further scouring. A minor erosion channel is called a rill, a larger channel a gully. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > водная эрозия
-
2 анод химического источника тока
анод химического источника тока
анод
Электрод химического источника тока, на котором протекают окислительные процессы.
[ ГОСТ 15596-82]EN
anode
by convention, cell electrode at which an oxidation reaction occurs
NOTE – The anode is the negative electrode during discharge and the positive electrode during charge.
[IEV number 482-02-27]FR
anode, f
par convention, électrode d'un élément à laquelle une réaction d’oxydation se produit
NOTE – L'anode est l'électrode négative pendant la décharge et l'électrode positive pendant la charge.
[IEV number 482-02-27]Тематики
Классификация
>>>Синонимы
EN
DE
- Anode, f
FR
Русско-французский словарь нормативно-технической терминологии > анод химического источника тока
-
3 биохимический цикл
биохимический цикл
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biogeochemical cycle
Movement of chemical elements in a circular pathway, from organisms to physical environment, back to organisms. The process is termed a nutrient cycle if the elements concerned are trace elements, which are essential to life. A biogeochemical cycle occurs when vegetation decomposes and minerals are incorporated naturally in the humus for future plant growth. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > биохимический цикл
-
4 бром
бром
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
bromine
A pungent dark red volatile liquid element of the halogen series that occurs in brine and is used in the production of chemicals. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > бром
-
5 быстродействующее автоматическое повторное включение
быстродействующее автоматическое повторное включение
БАПВ
Цикл АПВ, в котором выключатель вновь включается при достаточно малой бестоковой паузе tбт (tбт ≤ 0,3 с), чтобы избежать перебоев в электроснабжении
[ ГОСТ Р 52565-2006]
быстродействующее автоматическое повторное включение
БАПВ
Автоматическое повторное включение, осуществляемое при достаточно малой бестоковой паузе (0,3 с) после отключения короткого замыкания
[ОАО РАО "ЕЭС России" СТО 17330282.27.010.001-2008]EN
high speed automatic reclosing
an automatic reclosing which occurs after a time interval of the order of one second after tripping on fault
[IEV number 604-02-33]FR
réenclenchement rapide
réenclenchement automatique provoqué après un intervalle de temps de l'ordre de la seconde après un déclenchement sur défaut
[IEV number 604-02-33]
3.3.11. Быстродействующее АПВ, или БАПВ (одновременное включение с минимальной выдержкой времени с обоих концов), рекомендуется предусматривать на линиях по 3.3.10 для автоматического повторного включения, как правило, при небольшом расхождении угла между векторами ЭДС соединяемых систем. БАПВ может применяться при наличии выключателей, допускающих БАПВ, если после включения обеспечивается сохранение синхронной параллельной работы систем и максимальный электромагнитный момент синхронных генераторов и компенсаторов меньше (с учетом необходимого запаса) электромагнитного момента, возникающего при трехфазном КЗ на выводах машины.
[ПУЭ]Тематики
- высоковольтный аппарат, оборудование...
- электроснабжение в целом
Синонимы
EN
- fast automatic reclosing
- fast-acting automatic re-close
- high speed automatic reclosing
- high-speed reclosing
- HS reclosing
- HSR
- instantaneous reclosure
DE
- automatische Schnellwiedereinschaltung
- Schnellwiedereinschaltung, automatische
FR
Русско-французский словарь нормативно-технической терминологии > быстродействующее автоматическое повторное включение
-
6 выпадение осадков
выпадение осадков
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
fallout
The descent of airborne solid or liquid particles to the ground, which occurs when the speed at which they fall due to gravity exceeds that of any upward motion of the air surrounding them. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выпадение осадков
-
7 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
8 земная кора
земная кора
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
earth's crust
The outer layers of the Earth's structure, varying between 6 and 48 km in thickness, and comprising all the material above the Mohorovicic Discontinuity (a seismic discontinuity occurring between the crust of the earth and the underlying mantle; the discontinuity occurs at an average depth of 35 km below the continents and at about 10 km below the oceans). The earlier idea of a cool solid skin overlaying a hot molten interior has now been replaced by a concept of a crust composed of two shells: an inner basic unit composed of sima (oceanic crust) and an outer granitic unit composed of sial (continental crust). (Source: WHIT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > земная кора
-
9 инверсионный слой
инверсионный слой
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
inversion layer
The atmosphere layer through which an inversion occurs. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > инверсионный слой
-
10 катод химического источника тока
- cathode, f
катод химического источника тока
катод
Электрод химического источника тока, на котором протекают восстановительные процессы.
[ ГОСТ 15596-82]EN
cathode
by convention, cell electrode at which, a reduction reaction occurs
NOTE – The cathode is the positive electrode during discharge and the negative electrode during charge
[IEV number 482-02-28]FR
cathode, f
par convention, électrode d'un élément à laquelle une réaction de réduction se produit
NOTE – La cathode est l'électrode positive pendant la décharge et l'électrode négative pendant la charge.
[IEV number 482-02-28]Тематики
Классификация
>>>Синонимы
EN
DE
- Kathode, f
FR
- cathode, f
Русско-французский словарь нормативно-технической терминологии > катод химического источника тока
-
11 метаболизм пестицидов
метаболизм пестицидов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
metabolism of pesticides
The sum of chemical reactions, including both synthesis and breakdown, that occurs in substances or mixtures intended to prevent, destroy or mitigate pests that are directly or indirectly detrimental to harvest crops and other humans interests. (Source: SOI / TOE / IPC / DOE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > метаболизм пестицидов
-
12 нормальные условия
нормальные условия
Условия, при которых все средства защиты являются неповрежденными.
Примечание - При нормальных условиях все меры предосторожности для основной защиты (прежде всего - основная изоляция) находятся в неповрежденном состоянии, обеспечивая надлежащую защиту от поражения электрическим током.
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
нормальные условия
соответствующий набор влияющих величин и технических характеристик с нормальными значениями, их допусками и нормальными областями, по отношению к которым устанавливается систематическая составляющая относительной погрешности.
[ ГОСТ 6570-96]EN
normal condition
condition in which all means for protection against hazards are intact
[IEC 61010-031, ed. 1.0 (2002-01)]FR
condition normale
état dans lequel tous les moyens de protection contre les dangers sont intacts
[IEC 61010-031, ed. 1.0 (2002-01)]нормальные условия
-
[IEV number 442-01-31]EN
normal situation
situation where normally, only non-conductive pollution occurs but occasionally, a temporary conductivity caused by condensation can be expected
[IEV number 442-01-31]FR
situation normale
normalement, présence seulement d'une pollution non conductrice mais, occasionnellement, une conductivité temporaire provoquée par la condensation peut se développer
[IEV number 442-01-31]нормальные условия
Параметры, принятые для определения объема газов: температура 20 °С, давление 760 мм рт.ст. (101325 Н/м2), влажность равна 0. [ ГОСТ 2939-63, статья 2]
[ ГОСТ Р 52720-2007 ]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > нормальные условия
-
13 облучение продуктов питания
облучение продуктов питания
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
food irradiation
The most recent addition to food preservation technologies is the use of ionizing radiation, which has some distinct advantages over conventional methods. With irradiation, foods can be treated after packaging, thus eliminating post-processing contamination. In addition, foods are preserved in a fresh state and can be kept longer without noticeable loss of quality. Food irradiation leaves no residues, and changes in nutritional value due to irradiation are comparable with those produced by other processes. Irradiation is the process of applying high energy to a material, such as food, to sterilize or extend its shelf-life by killing microorganisms, insects and other pests residing on it. Sources of ionizing radiation that have been used include gamma rays, electron beams and X-rays. Gamma rays are produced by radioactive isotopes such as Cobalt-60. Electron beams are produced by linear accelerators, which themselves are powered by electricity. The dose applied to a product is the most important factor of the process. At high doses, food is essentially sterilized, just as occurs in canning. Products so treated can be stored at room temperature almost indefinitely. Controversial and banned in some countries. (Source: IFSE / VCN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > облучение продуктов питания
-
14 озон
озон
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
ozone
An allotropic form of oxygen containing three atoms in the molecule. It is a bluish gas, very active chemically, and a powerful oxidizing agent. Ozone is formed when oxygen or air is subjected to a silent electric discharge. It occurs in ordinary air in very small amounts only. (Source: UVAROV)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > озон
-
15 перегрузка
- surcharge d’un circuit
- surcharge
- débordement
перегрузка
Условия появления сверхтока в электрически не поврежденной цепи.
МЭК 60050(441-11-08).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
перегрузка
Условия оперирования в электрически неповреждённой цепи, которые вызывают сверхток.
В электрических цепях электроустановки здания могут возникать сверхтоки при отсутствии в них электрических повреждений. Причиной появления этих сверхтоков является перегрузка электрических цепей. Перегрузка характеризуется током перегрузки, который превышает номинальный ток электрической цепи и допустимые длительные токи её проводников. Длительная перегрузка проводников может вызвать их сильный нагрев и стать причиной пожара в здании. Поэтому в электроустановках зданий выполняют защиту от перегрузок с помощью устройств защиты от сверхтока. Перегрузки могут также возникать при переходных процессах в электрических цепях, например, при включении электрооборудования.
[ http://www.volt-m.ru/glossary/letter/%CF/view/46/]
перегрузка
Отношение время/электрический ток для цепи, в которой превышена максимальная допустимая нагрузка, когда цепь находится в исправном состоянии.
Примечание - Не следует использовать термин «перегрузка» как синоним термина «сверхток».
[ГОСТ ЕН 1070-2003]
перегрузка (цепи)
Времятоковая зависимость для цепи, в которой превышена максимальная нагрузка, когда цепь находится в исправном состоянии.
Примечание
Не следует использовать термин «перегрузка» как синоним сверхтока.
[ ГОСТ Р МЭК 60204-1-2007]
перегрузка
Превышение фактического значения мощности или тока электротехнического изделия (устройства) над номинальным значением.
Примечание. Допускается с введением соответствующего пояснения оценивать перегрузку полным значением параметра, превышающим номинальное значение.
[ ГОСТ 18311-80]
перегрузка
-
[IEV number 314-02-09]EN
overload
operating conditions in an electrically undamaged circuit which cause an over-current.
[IEC 60947-1, ed. 5.0 (2007-06)]
overload, noun
excess of the actual load over the full load, expressed by their difference
Source: 151-15-16
[IEV number 151-15-30]
overflow
condition which occurs when the numerical value of the output information exceeds the maximum possible value which can be displayed or represented
[IEV number 314-02-09]FR
surcharge
conditions de fonctionnement d’un circuit électriquement sain, qui provoquent une surintensité.
[IEC 60947-1, ed. 5.0 (2007-06)]
surcharge, f
excédent de la charge réelle sur la pleine charge, exprimé par leur différence
Source: 151-15-16
[IEV number 151-15-30]
débordement
condition de fonctionnement pour lequel la valeur numérique de l'information de sortie dépasse la possibilité maximale d'affichage ou de représentation de l'appareil
[IEV number 314-02-09]Тематики
- электротехника, основные понятия
Синонимы
EN
- OL
- overcharge
- overdrive
- overflow
- overload
- overload of a circuit
- overloading
- ovId
- surcharge load
- thermal overload situation
DE
FR
- débordement
- surcharge
- surcharge d’un circuit
Русско-французский словарь нормативно-технической терминологии > перегрузка
-
16 плутоний
плутоний
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
plutonium
A highly toxic metallic transuranic element. It occurs in trace amounts in uranium ores and is produced in a nuclear reactor by neutron bombardment of uranium-238. The most stable and important isotope, plutonium-239, readily undergoes fission and is used as a reactor fuel in nuclear power stations and in nuclear weapons. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > плутоний
-
17 посадка напряжения
посадка напряжения
Внезапное значительное снижение напряжения в системе электроснабжения.
[ ГОСТ 23875-88]EN
voltage collapse
sudden decrease in voltage leading to loss of voltage in the whole or a part of a power system
NOTE – A cascading tripping of generating units and/or transmission lines usually occurs during voltage collapse.
[IEV number 604-01-22 ]
voltage depression
system condition characterized by a sustained and significant lowering of voltage in the whole or part of a power system
[IEV number 604-01-44]FR
écroulement de la tension
baisse soudaine de la tension conduisant à la disparition de la tension dans tout ou partie d'un réseau d'énergie électrique
NOTE – Des déclenchements en cascade d'unités de production et/ou de lignes de transport d'énergie électrique se produisent généralement lors d'un écroulement de la tension.
[IEV number 604-01-22 ]
baisse profonde de la tension
état d'un réseau d'énergie électrique caractérisé par une baisse durable et significative de la tension dans tout ou partie du réseau
[IEV number 604-01-44]Тематики
EN
DE
FR
Смотри также
D. Spannungszusammenbruch
E. Voltage depression (voltage collapse)
F. Effondrement de la tension
Внезапное значительное снижение напряжения в системе электроснабжения
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > посадка напряжения
18 природный камень
природный камень
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
natural stone
A gemstone that occurs in nature, as distinguished from a man-made substitute. (Source: BJGEO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > природный камень
19 разъединитель
разъединитель
Контактный коммутационный аппарат, в разомкнутом положении отвечающий требованиям к функции разъединения.
Примечание.
1 Это определение отличается от формулировки МЭК 60050(441-14-05), поскольку требования к функции разъединения не ограничиваются соблюдением изолирующего промежутка.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
2 Разъединитель способен включать и отключать цепь с незначительным током или при незначительном изменении напряжения на зажимах каждого из полюсов разъединителя.
Разъединитель может проводить токи в нормальных условиях работы, а также в течение определенного времени в аномальных условиях работы выдерживать токи короткого замыкания.
Условное обозначение контакта разъединителя
[ ГОСТ Р 50030. 3-99 ( МЭК 60947-3-99)]
разъединитель
Контактный коммутационный аппарат, который обеспечивает в отключенном положении изоляционный промежуток, удовлетворяющий нормированным требованиям.
Примечания
1 Разъединитель способен размыкать и замыкать цепь при малом токе или малом изменении напряжения на выводах каждого из его полюсов. Он также способен проводить токи при нормальных условиях в цепи и проводить в течение нормированного времени токи при ненормальных условиях, таких как короткое замыкание.
2 Малые токи - это такие токи, как емкостные токи вводов, шин, соединений, очень коротких кабелей, токи постоянно соединенных ступенчатых сопротивлений выключателей и токи трансформаторов напряжения и делителей. Для номинальных напряжений до 330 кВ включительно ток, не превышающий 0,5 А, считается малым током по этому определению; для номинального напряжения от 500 кВ и выше и токов, превышающих 0,5 А, необходимо проконсультироваться с изготовителем, если нет особых указаний в руководствах по эксплуатации разъединителей.
3 К малым изменениям напряжения относятся изменения напряжения, возникающие при шунтировании регуляторов индуктивного напряжения или выключателей.
4 Для разъединителей номинальным напряжением от 110 кВ и выше может быть установлена коммутация уравнительных токов.
[ ГОСТ Р 52726-2007]EN
disconnector
a mechanical switching device which provides, in the open position, an isolating distance in accordance with specified requirements
NOTE – A disconnector is capable of opening and closing a circuit when either negligible current is broken or made, or when no significant change in the voltage across the terminals of each of the poles of the disconnector occurs. It is also capable of carrying currents under normal circuit conditions and carrying for a specified time currents under abnormal conditions such as those of short circuit.
[IEV number 441-14-05]
disconnector
IEV 441-14-05 is applicable with the following additional notes:
NOTE 1
"Negligible current" implies currents such as the capacitive currents of bushings, busbars, connections, very short lengths of cable, currents of permanently connected grading impedances of circuit-breakers and currents of voltage transformers and dividers. For rated voltages of 420 kV and below, a current not exceeding 0,5 A is a negligible current for the purpose of this definition; for rated voltage above 420 kV and currents exceeding 0,5 A, the manufacturer should be consulted.
"No significant change in voltage" refers to such applications as the by-passing of induction voltage regulators or circuit-breakers.
NOTE 2
For a disconnector having a rated voltage of 52 kV and above, a rated ability of bus transfer current switching may be assigned
[IEC 62271-102]FR
sectionneur
appareil mécanique de connexion qui assure, en position d'ouverture, une distance de sectionnement satisfaisant à des conditions spécifiées
NOTE – Un sectionneur est capable d'ouvrir et de fermer un circuit lorsqu'un courant d'intensité négligeable est interrompu ou établi, ou bien lorsqu'il ne se produit aucun changement notable de la tension aux bornes de chacun des pôles du sectionneur. Il est aussi capable de supporter des courants dans les conditions normales du circuit et de supporter des courants pendant une durée spécifiée dans des conditions anormales telles que celles du court-circuit.
[IEV number 441-14-05]Указанные в 5.3.2 перечислениях а)-d) устройства отключения ( выключатель-разъединитель, разъединитель или выключатель) должны:
- изолировать электрооборудование от цепей питания и иметь только одно положение ОТКЛЮЧЕНО (изоляция) и одно положение ВКЛЮЧЕНО, четко обозначаемые символами «О» и «I» [МЭК 60417-5008 (DB:2002-10) и МЭК 60417-5007 (DB:2002-10), см. 10.2.2];
- иметь видимое разъединение или индикатор положения, который может указывать положение ОТКЛЮЧЕНО только в случае, если все контакты в действительности открыты, т.е. разомкнуты и удалены друг от друга на расстояние, удовлетворяющее требованиям по изолированию;
- быть снабжены расположенным снаружи ручным приводом (например, ручкой). Исключение для управляемых внешним источником энергии, когда воздействие вручную невозможно при наличии иного внешнего привода. Если внешние приводы не используются для выполнения аварийных функций управления, то рекомендуется применять ЧЕРНЫЙ и СЕРЫЙ цвета для окраски ручного привода (см. 10.7.4 и 10.8.4);
- обладать средствами для запирания в положении ОТКЛЮЧЕНО (например, с помощью висячих замков). При таком запирании возможность как дистанционного, так и местного включения должна быть исключена;
Разъединители служат для создания видимого разрыва, отделяющего выводимое в ремонт оборудование от токоведущих частей, находящихся под напряжением, для безопасного производства работ.
Разъединители не имеют дугогасящих устройств и поэтому предназначаются для включения и отключения электрических цепей при отсутствии тока нагрузки и находящихся только под напряжением или даже без напряжения. Лишь в некоторых случаях допускается включение и отключение разъединителями небольших токов, значительно меньше номинальных.
Разъединители используются также при различного рода переключениях в схемах электрических соединений подстанций, например при переводе присоединений с одной системы шин на другую.
Требования, предъявляемые к разъединителям с точки зрения оперативного обслуживания, следующие:- Разъединители в отключенном положении должны создавать ясно видимый разрыв цепи, соответствующий классу напряжения установки.
- Приводы разъединителей должны иметь устройства фиксации в каждом из двух оперативных положений: включенном и отключенном. Кроме того, они должны иметь надежные упоры, ограничивающие поворот главных ножей на угол больше заданного.
- Опорные изоляторы и изолирующие тяги должны выдерживать механическую нагрузки при операциях.
- Главные ножи разъединителей должны иметь блокировку с ножами стационарных заземлителей и не допускать возможности одновременного включения тех и других.
- Разъединители должны беспрепятственно включаться и отключаться при любых наихудших условиях окружающей среды (например, при обледенении).
- Разъединители должны иметь надлежащую изоляцию, обеспечивающую не только надежную работу при возможных перенапряжениях и ухудшении атмосферных условий (гроза, дождь, туман), но и безопасное обслуживание.
[ http://forca.ru/stati/podstancii/obsluzhivanie-razediniteley-otdeliteley-i-korotkozamykateley.html]
Разъединители применяются для коммутации обесточенных при помощи выключателей участков токоведущих систем, для переключения РУ с одной ветви на другую, а также для отделения на время ревизии или ремонта силового электротехнического оборудования и создания безопасных условий от смежных частей линии, находящихся под напряжением. Разъединители способны размыкать электрическую цепь только при отсутствии в ней тока или при весьма малом токе. В отличие от выключателей разъединители в отключенном состоянии образуют видимый разрыв цепи. После отключения разъединителей с обеих сторон объекта, например выключателя или трансформатора, они должны заземляться с обеих сторон либо при помощи переносных заземлителей, либо специальных заземляющих ножей, встраиваемых в конструкцию разъединителя.
[ http://relay-protection.ru/content/view/46/8/1/1/]
Параллельные тексты EN-RU
b) disconnector, with or without fuses, in accordance with IEC 60947-3, that has an auxiliary contact that in all cases causes switching devices to break the load circuit before the opening of the main contacts of the disconnector;
[IEC 60204-1-2006]
б) разъединитель с или без предохранителей, соответствующий требованиям МЭК 60947-3 со вспомогательным контактом, срабатывающим до того, как разомкнутся главные контакты разъединителя, используемым для коммутации другого аппарата, отключающего питание цепей нагрузки.
[Перевод Интент]
Тематики
- высоковольтный аппарат, оборудование...
- релейная защита
- электротехника, основные понятия
Классификация
>>>EN
- disconnect
- disconnect device
- disconnect switch
- disconnecting device
- disconnecting switch
- disconnector
- DS
- isolating facility
- isolating switch
- isolator
- main disconnect device
DE
FR
Смотри также
Русско-французский словарь нормативно-технической терминологии > разъединитель
20 редколесье умеренной климатической зоны
редколесье умеренной климатической зоны
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
temperate woodland
Forest dominated by broad-leaved hardwoods, which occurs over large tracts in the mid-latitudes of Europe, N. America, and eastern Asia, but which is restricted in the southern hemisphere to Chilean Patagonia. (Source: ALL2)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > редколесье умеренной климатической зоны
Страницы- 1
- 2
См. также в других словарях:
Occurs check — In computer science, the occurs check is a part of algorithms for syntactic unification. It causes unification of a logic variable V and a structure S to fail if S contains V. In theorem proving, unification without the occurs check can lead to… … Wikipedia
Occurs check — Der Occurs check bezeichnet in der Informatik einen Teil des Unifikationsalgorithmus. Er verhindert, dass eine Variable durch einen Term ersetzt wird, der diese Variable enthält. Anwendung findet er bspw. bei der Typprüfung in funktionalen… … Deutsch Wikipedia
occurs — oc·cur || É™ kÉœr /É™ kÉœË v. happen, take place, transpire; come to mind, suggest itself … English contemporary dictionary
occurs — 1) succor 2) crocus … Anagrams dictionary
OCCURS — … Useful english dictionary
Occurs when an individual owns securities. An owner of 1,000 shares of stock is said to be Long the stock. Related: Short position — Long run A period of time in which all costs are variable; greater than one year. The New York Times Financial Glossary … Financial and business terms
As It Occurs To Me — Hosting British Comedy Guide Updates Weekly Debut 13 October 2009 End date 20 June 2011 Genre Comedy Website … Wikipedia
time during which anything occurs — index date Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
it occurs to me — this thought comes to my mind It occurs to me that we won t meet again until Christmas … English idioms
Overleveraged — Occurs when a business is carrying too much debt, and is unable to pay interest payments from loans. Overleveraged companies are unable to pay their expenses because of over excessive costs. This is the formula for financial leverage. Occurs when … Investment dictionary
Beam — Occurs in the Authorized Version as the rendering of various Hebrew words. In 1 Sam. 17:7, it means a weaver s frame or principal beam; in Hab. 2:11, a crossbeam or girder; 2 Kings 6:2, 5, a cross piece or rafter of a house; 1 Kings 7:6, an… … Easton's Bible Dictionary
Перевод: с русского на французский
с французского на русский- С французского на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский