-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
2 максимальный ожидаемый пиковый ток (цепи переменного тока)
максимальный ожидаемый пиковый ток (цепи переменного тока)
Ожидаемый пиковый ток, возникающий в момент, обусловливающий его наибольшее возможное значение.
Примечание. В многофазной цепи многополюсного аппарата максимальный ожидаемый ток характеризует только один полюс
МЭК 60050(441-17-04).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
maximum prospective peak current (of an a.c. circuit)
the prospective peak current when initiation of the current takes place at the instant which leads to the highest possible value
NOTE – For a multiple device in a polyphase circuit, the maximum prospective peak current refers to a single pole only.
[IEV number 441-17-04]FR
valeur maximale de crête du courant présumé (d'un circuit à courant alternatif)
valeur de crête du courant présumé quand l'établissement du courant a lieu à l'instant qui conduit à la plus grande valeur possible
NOTE – Pour un appareil multipolaire dans un circuit polyphasé, la valeur maximale de crête du courant présumé ne se rapporte qu'à un seul pôle.
[IEV number 441-17-04]Тематики
- выключатель автоматический
- выключатель, переключатель
- электротехника, основные понятия
EN
- maximum prospective peak current (of an a.c. circuit)
DE
FR
- valeur maximale de crête du courant présumé (d'un circuit à courant alternatif)
Русско-немецкий словарь нормативно-технической терминологии > максимальный ожидаемый пиковый ток (цепи переменного тока)
См. также в других словарях:
Multiple myeloma — Classification and external resources Micrograph of a plasmacytoma, the histologic correlate of multiple myeloma. H E stain ICD … Wikipedia
Multiple Natures — is a personality type framework developed by renowned American educator and researcher, Steven Rudolph. It attempts to account for people’s natures and personality traits that lead to particular behavioral patterns, especially with respect to… … Wikipedia
Multiple chemical sensitivity — Classification and external resources MeSH D018777 Multiple chemical sensitivity (MCS) is a chronic medical condition characterized by symptoms the affected person attributes to exposure to low levels of chemicals. Commonly suspected substances… … Wikipedia
Value network analysis — is a methodology for understanding, using, visualizing, optimizing internal and external value networks and complex economic ecosystems. The methods include visualizing sets of relationships from a dynamic whole systems perspective. Robust… … Wikipedia
Multiple trace theory — (MTT) is a memory consolidation model advanced as an alternative model to strength theory. It posits that each time some information is presented to a person, it is neurally encoded in a unique memory trace composed of a combination of its… … Wikipedia
Multiple Maniacs — Directed by John Waters Produced by John Waters Written by John Waters Starring Divine Dav … Wikipedia
Value noise — is a type of noise commonly used as a procedural texture primitive in computer graphics. It is conceptually different, and often confused with gradient noise examples of which are the Perlin noise and Simplex noise. This method consists of a… … Wikipedia
Multiple Maniacs — est le second film de John Waters réalisé en 1970 (et tourné à Baltimore en 16mm et en noir et blanc) avec Divine, Mary Vivian Pearce, David Lochary, Mink Stole, et pour la première fois Edith Massey dans son propre rôle de serveuse. Le titre du… … Wikipédia en Français
Multiple rule-based problems — are problems containing various conflicting rules and restrictions. Such problems typically have an optimal solution, found by striking a balance between the various restrictions, without directly defying any of the aforementioned restrictions.… … Wikipedia
Multiple (finance) — Multiple in financial terminology is a metric used in valuation of companies. The most commonly used multiples are: P/E (Price earnings ratio), EV/EBITDA (Enterprise value to Earnings before Interest, Taxes, Depreciation, and Amortization). In… … Wikipedia
Multiple component pricing — refers to the practice of valuing farm milk according to the value of its protein, fat, and mineral content. This practice has been adopted by many regions for federal milk marketing orders. Historically, milk was priced solely on the basis of… … Wikipedia
