-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
Multiple patterning — is a class of technologies developed for photolithography to enhance the feature density. The simplest case of multiple patterning is double patterning, where a conventional lithography process is enhanced to produce double the expected number of … Wikipedia
Multiple system atrophy — Classification and external resources ICD 10 G90.3 ICD 9 333.0 … Wikipedia
Multiple drug resistance — or Multidrug resistance is a condition enabling a disease causing organism to resist distinct drugs or chemicals of a wide variety[1] of structure and function targeted at eradicating the organism. Organisms that display multidrug resistance can… … Wikipedia
Multiple integral — Topics in Calculus Fundamental theorem Limits of functions Continuity Mean value theorem Differential calculus Derivative Change of variables Implicit differentiation Taylor s theorem Related rates … Wikipedia
Limit superior and limit inferior — In mathematics, the limit inferior (also called infimum limit, liminf, inferior limit, lower limit, or inner limit) and limit superior (also called supremum limit, limsup, superior limit, upper limit, or outer limit) of a sequence can be thought… … Wikipedia
Multiple exciton generation — Breakdown of the causes for the Shockley Queisser limit. The black height is Shockley Queisser limit for the maximum energy that can be extracted as useful electrical power in a conventional solar cell. However, a multiple exciton generation… … Wikipedia
Limit of a function — x 1 0.841471 0.1 0.998334 0.01 0.999983 Although the function (sin x)/x is not defined at zero, as x becomes closer and closer to zero, (sin x)/x becomes arbitrarily close to 1. It is said that the limit of (sin x)/x as x approache … Wikipedia
Multiple unit — This article is about Multiple Units vehicles. For the train control technology, see Multiple unit train control. Multiple unit trains Subtypes Electric multiple unit Diesel multiple unit Push–pull train Technology … Wikipedia
Multiple star — Artist s impression of the orbits of HD 188753, a triple star system A multiple star consists of three or more stars which appear from the Earth to be close to one another in the sky. This may result from the stars being physically close and… … Wikipedia
Multiple-prism dispersion theory — The first description of multiple prism arrays, and multiple prism dispersion, was given by Newton in his book Opticks.[1] Prism pair expanders were introduced by Brewster in 1813.[2] A modern mathematical description of the single prism… … Wikipedia
Multiple-try Metropolis — In Markov chain Monte Carlo, the Metropolis–Hastings algorithm (MH) can be used to sample from a probability distribution which is difficult to sample from directly. However, the MH algorithm requires the user to supply a proposal distribution,… … Wikipedia
