-
1 многожильный кабель
многожильный кабель
многожильный провод
многожильный шнур
Кабель (провод, шнур), в котором число жил более трех.
[ ГОСТ 15845-80]EN
multicore cable
cable having more than one core
Note – The French term «câble multipolaire» is more specifically used to designate the cable constituting the phases of a multiphase system (example: three-core cable).
[EV ref 461-06-04]
multiconductor cable
cable having more than one conductor, some of which may be uninsulated
[IEV ref 461-06-03]FR
câble multiconducteur
câble multipolaire
câble comprenant plus d'un conducteur isolé
Note – Le terme câble multipolaire est plus particulièrement utilisé pour désigner le câble constituant les phases d'un système polyphasé (exemple: câble tripolaire).
[EV ref 461-06-04]
câble multiconducteur
câble multipolaire
câble comprenant plus d'une âme, dont éventuellement certaines non isolées
[IEV ref 461-06-03]
Core - (токопроводящая) жила;
Insulator - изоляция жилы;
Protective Sheath - оболочка кабеля.Недопустимые, нерекомендуемые
Примечание(1) Мнение автора карточкиТематики
- кабели, провода...
EN
- bundled cable
- multi-pole cable
- multiconductor cable
- multicore cable
- multiple cable
- multiple-conductor cable
- multiple-core cable
- multistrand cable
- N-conductor cable
- polycore cable
DE
- mehradriges Kabel, n
- Mehrleiterkabel, n
FR
Русско-французский словарь нормативно-технической терминологии > многожильный кабель
-
2 многожильный кабель
câble multiconducteur [multiple]; câble monotoron [toronné]Русско-французский политехнический словарь > многожильный кабель
-
3 многожильный провод
adjeng. conducteur câblé, conducteur divisé, conducteur multiple, câble, fil de litz, fil divisé, fil multiple, fil toronné, fil torsadé, fil à brins multiples -
4 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
5 многожильный кабель
adj1) eng. câble divisé, câble multibrin, câble toronné, câble à faisceau d'éléments2) radio. câble multiconducteur3) electr. fil compound4) mech.eng. câble multiple -
6 многофазный кабель
adjmech.eng. câble multiple
См. также в других словарях:
Cable-stayed bridge — BridgeTypePix image title=The Rio Antirio bridge in Greece type name=Cable stayed bridge sibling names=None descendent names=Side spar cable stayed bridge, Self anchored suspension bridge, cantilever spar cable stayed bridge ancestor… … Wikipedia
Multiple system operator — A Multiple System Operator or Multi System Operator (MSO) is an operator of multiple cable television systems. A cable system in the United States, by Federal Communications Commission (FCC) definition, is a facility serving a single community or … Wikipedia
Cable landing point — A cable landing point is the location where a submarine or other underwater cable makes landfall. The term is most often used for the landfall points of submarine telecommunications cables and submarine power cables. The main cable is joined to a … Wikipedia
Cable television headend — is a master facility for receiving television signals for processing and distribution over a cable television system. The headend facility is normally unstaffed and surrounded by some type of security fencing and is typically a building or large… … Wikipedia
Cable jetting — is a technique to install cables in ducts [http://www.plumettaz.ch/en/products/optical fiber/jetting explanation.asp] . It is commonly used to install cables with optical fibers in underground polyethylene ducts and is an alternative to pulling … Wikipedia
Cable barrier — Cable barrier, sometimes referred to as guard cable, is a type of roadside or median barrier. It consists of steel wire ropes mounted on weak posts. As is the case with any roadside barrier, its primary purpose is to prevent a vehicle from… … Wikipedia
Multiple-unit train control — Multiple unit train control, sometimes abbreviated to multiple unit or MU, is a method of simultaneously controlling all the traction equipment in a train from a single location, whether it is a Multiple unit comprising a number of self powered… … Wikipedia
Multiple Single-Level — or Multi Security Level (MSL) is a method of separating different levels of data by using separate PCs or virtual machines for each level. It aims to give some of the benefits of Multilevel security without needing special changes to the OS or… … Wikipedia
Cable modem — Motorola SurfBoard SBV6120E EuroDOCSIS 3.0 cable modem A cable modem is a type of network bridge and modem that provides bi directional data communication via radio frequency channels on a HFC and RFoG infrastructure. Cable modems are primarily… … Wikipedia
Cable converter box — Pace Micro Technology DC757X HD cable box A cable converter box or television converter box is an electronic tuning device that transposes/converts any of the available channels from a cable television service to an analog RF signal on a single… … Wikipedia
Cable ethernet — Ethernet Connecteur RJ45 pour Ethernet Pile de protocoles … Wikipédia en Français
