-
1 прямой пуск вращающегося электродвигателя
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Русско-французский словарь нормативно-технической терминологии > прямой пуск вращающегося электродвигателя
-
2 вторичная обработка
вторичная обработка
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
secondary treatment
Stage of the process of waste water treatment: following primary treatment by sedimentation, the second step in most wastewater systems in which biological organisms decompose most of the organic matter into a innocuous, stable form. (Source: CORBIT / WQA)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > вторичная обработка
-
3 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
4 источник энергии, не загрязняющий окружающую среду
источник энергии, не загрязняющий окружающую среду
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
non-polluting energy source
Energy that is ecologically safe and renewable. The most widely used source is hydroelectric power, which currently supplies some 6.6% of the world's energy needs. Other non-polluting sources are solar energy, tidal energy, wave energy and wind energy. Most non-polluting energy sources require a high capital investment but have low running costs. (Source: GILP96 / UVAROV)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > источник энергии, не загрязняющий окружающую среду
-
5 контроль за загрязнением
контроль за загрязнением
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
pollution control
Chemical and physical methods to lessen discharges of most pollutants; for carbon dioxide there is, at present, no economic or practical way to reduce the quantities discharged except by reduced fossil fuel usage. Most specific means for removing pollutants from emissions include flue-gas desulphurisation, fluidised combustion, catalytic converters and the redesign of equipment, such as furnace burners and car engines, to lessen the production of pollutants. (Source: BRACK)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > контроль за загрязнением
-
6 НКУ защищенное
НКУ защищенное
НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
защищенное НКУ
НКУ, конструкция которого обеспечивает требуемую степень защиты со всех сторон от прикосновения к частям, находящимся под напряжением (за исключением монтажной поверхности).
[ ГОСТ Р МЭК 61439.1-2013]EN
enclosed assembly (of switchgear and controlgear)
an assembly enclosed on all sides, top and bottom in such a manner as to provide a specified degree of protection
NOTE – The mounting surface may form a part of the enclosure when specified in the relevant publication.
[IEV number 441-12-02]FR
ensemble (d'appareillage de connexion et de commande)
sous enveloppe
ensemble comportant une paroi sur toutes ses faces latérales, supérieure et inférieure, de façon à assurer un degré de protection spécifié
NOTE – La surface de montage peut faire partie de l'enveloppe lorsqu'une publication particulière le spécifie.
[IEV number 441-12-0
Шкаф - защищенное НКУ, предназначенное для установки на полу
Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Обобщающие термины
Синонимы
EN
- enclosed assembly (of switchgear and controlgear)
- enclosed switchboard
- safety enclosed board
- safety enclosed switchgear
DE
FR
Русско-французский словарь нормативно-технической терминологии > НКУ защищенное
-
7 облучение продуктов питания
облучение продуктов питания
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
food irradiation
The most recent addition to food preservation technologies is the use of ionizing radiation, which has some distinct advantages over conventional methods. With irradiation, foods can be treated after packaging, thus eliminating post-processing contamination. In addition, foods are preserved in a fresh state and can be kept longer without noticeable loss of quality. Food irradiation leaves no residues, and changes in nutritional value due to irradiation are comparable with those produced by other processes. Irradiation is the process of applying high energy to a material, such as food, to sterilize or extend its shelf-life by killing microorganisms, insects and other pests residing on it. Sources of ionizing radiation that have been used include gamma rays, electron beams and X-rays. Gamma rays are produced by radioactive isotopes such as Cobalt-60. Electron beams are produced by linear accelerators, which themselves are powered by electricity. The dose applied to a product is the most important factor of the process. At high doses, food is essentially sterilized, just as occurs in canning. Products so treated can be stored at room temperature almost indefinitely. Controversial and banned in some countries. (Source: IFSE / VCN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > облучение продуктов питания
-
8 пролив Ваддензе
пролив Ваддензе
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
Wadden Sea
The Wadden sea is a shallow sea extending along the North Sea coasts of The Netherlands, Germany and Denmark. It is a highly dynamic ecosystem with tidal channels, sands, mud flats, salt marshes, beaches, dunes, river mouths and a transition zone to the North Sea, the offshore zone. Most parts of the Wadden Sea, in particular in The Netherlands and Lower Saxony, are sheltered by barrier islands and contain smaller or wider areas of intertidal flats. The present form of the Wadden Sea is the result of both natural forces and action by man. Twice a day, on average, 15 km3 of sea water enter the Wadden sea. With the water from the North Sea, large amount of sand and silt are imported which settle in places with little water movement. During low tides large parts of the Wadden Sea emerge. These so-called tidal flats cover about 2/3 of the tidal area and are one of its most characteristic features. Nowhere in the world can such a large unbroken stretch of tidal flats be found. They account for 60% of all tidal areas in Europe and North Africa. (Source: CWSS)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > пролив Ваддензе
-
9 система комплексного планирования и программирования
система комплексного планирования и программирования
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
Planning-Programming-Budgeting System
A system to achieve long-term goals or objectives by means of analysis and evaluation of the alternatives. PPB is designed to solve problems by finding the most effective and most efficient solution on the basis of objective criteria. (Source: GREENW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > система комплексного планирования и программирования
-
10 травы
травы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
grass
A very large and widespread family of Monocotyledoneae, with more than 10.000 species, most of which are herbaceous, but a few are woody. The stems are jointed, the long, narrow leaves originating at the nodes. The flowers are inconspicuous, with a much reduced perianth, and are wind-pollinated or cleistogamous. The fruit in single-seeded, usually a caryopsis. Grasses are the most important of all plants for food. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > травы
-
11 формирование почвы
формирование почвы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
soil formation
The combination of natural processes by which soils are formed. It is also known as pedogenesis. The most important soil-forming factors are parent material, terrain, climate, aspect, vegetation cover, microorganisms in the soil and the age of the land surface. Some pedologists would add to this list the influence of human activities. All the factors exhibit varying degrees of interrelationship and some are more important than others, with climate often being singled out as the most important. (Source: WHIT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > формирование почвы
-
12 фтор
фтор
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
fluorine
A gaseous or liquid chemical element; a member of the halide family, it is the most electronegative element and the most chemically energetic of the nonmetallic elements; highly toxic, corrosive, and flammable; used in rocket fuels and as a chemical intermediate. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > фтор
-
13 хвойный лес
хвойный лес
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
coniferous forest
A forest type characterized by cone-bearing, needle-leaved trees. They are generally, but not necessarily, evergreen and relatively shallow-rooted. Since they grow more rapidly than most broad-leaved trees, conifers are extensively planted as a source of softwood timber and pulp. They are tolerant of wide-ranging climatic conditions, of many different types of soil and of considerable differences in terrain. Thus, they are found from the polar latitudes to the tropics, on most types of soils (especially, thin acid soils) and from mountain summits to coastal environments. (Source: WHIT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > хвойный лес
-
14 цементная промышленность
цементная промышленность
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
cement industry
Industry for the production of cement. The emissions of most relevance from this sector are atmospheric: dust, carbon dioxide and nitrogen oxides are the most important. Cement is essential for the construction sector, either directly or mixed with sand or gravel to form concrete. (Source: DOBRIS)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > цементная промышленность
-
15 электрическая дуга
электрическая дуга
-
[Интент]EN
(electric) arc
self-maintained gas conduction for which most of the charge carriers are electrons supplied by primary‑electron emission
[IEV ref 121-13-12]FR
arc (électrique), m
conduction gazeuse autonome dans laquelle la plupart des porteurs de charge sont des électrons produits par émission électronique primaire
[IEV ref 121-13-12]-
Материалы, стойкие к воздействию электрической дуги, используемые в качестве защитных средств, должны быть несгораемыми, иметь низкую теплопроводность и достаточную толщину для обеспечения механической стойкости.
[ ГОСТ Р 50571. 4-94 ( МЭК 364-4-42-80)] -
Средства индивидуальной защиты от теплового воздействия электрической дуги...
[Технический регламент о безопасности средств индивидуальной защиты] -
Опасное и вредное воздействия на людей электрического тока, электрической дуги и электромагнитных полей проявляются в виде электротравм и профессиональных заболеваний.
[ ГОСТ 12.1.019-79] -
сопротивление электрической дуги в месте КЗ
[ ГОСТ 28249-93 ] -
... способствовать гашению электрической дуги
-
Аппараты управления, имеющие электрическую дугу на силовых контактах при
нормальной работе ( пускатели, станции управления), должны проходить испытания при коммутации нагрузки.
[ ГОСТ Р 51330.20-99]
An electric arc is an electrical breakdown of a gas which produces an ongoing plasma discharge, resulting from a current flowing through normally nonconductive media such as air. A synonym is arc discharge. An arc discharge is characterized by a lower voltage than a glow discharge, and relies on thermionic emission of electrons from the electrodes supporting the arc. The phenomenon was first described by Vasily V. Petrov, a Russian scientist who discovered it in 1802. An archaic term is voltaic arc as used in the phrase " voltaic arc lamp".
[http://en.wikipedia.org/wiki/Electric_arc]Параллельные тексты EN-RU
In the last years a lot of users have underlined the question of safety in electrical assemblies with reference to one of the most severe and destructive electrophysical phenomenon: the electric arc.
[ABB]В последние годы многие потребители обращают особое внимание на безопасность НКУ, связанную с чрезвычайно разрушительным и наиболее жестко действующим электрофизическим явлением - электрической дугой.
[Перевод Интент]Тематики
- электротехника, основные понятия
Действия
Сопутствующие термины
EN
DE
- elektrischer Lichtbogen, m
- Lichtbogen, m
FR
Русско-французский словарь нормативно-технической терминологии > электрическая дуга
-
Материалы, стойкие к воздействию электрической дуги, используемые в качестве защитных средств, должны быть несгораемыми, иметь низкую теплопроводность и достаточную толщину для обеспечения механической стойкости.
-
16 Карлов мост
ngener. "Pont Charles" (Karlov Most) -
17 Арктический регион
Арктический регион
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
Arctic region
The northernmost area of the earth, centered on the North Pole, that includes the Arctic Ocean, the northern reaches of Canada, Alaska, Russia, Norway and most of Greenland, Iceland and Svalbard. (Source: INP)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > Арктический регион
-
18 аммиак
аммиак
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
ammonia
A colorless gaseous alkaline compound that is very soluble in water, has a characteristic pungent odour, is lighter than air, and is formed as a result of the decomposition of most nitrogenous organic material. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > аммиак
-
19 антиводорослевый реагент
антиводорослевый реагент
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
antifouling agent
Agent that inhibits the growth of barnacles and other marine organisms on a ship's bottom (an antifouling paint or other coating). Organo-tin compounds have been the most often used agents in this application since they are effective against both soft and hard fouling organisms. However, in spite of their performance, they have a negative impact on the marine environment and their long half life in the environment, has prompted marine paint manufacturers to look for a nonpersistent alternative. (Source: CED / OLIN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > антиводорослевый реагент
-
20 бесшумная технология
бесшумная технология
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
noise-free technology
Sound is radiated both as air-borne and as structure-borne; most sources produce both, thus various noise attenuation principles must be employed. Measures include: the replacement of components with quieter parts and material; the enclosure of particularly noisy components; the selection of quieter types of fan; the replacement of noisy compressed-air nozzles with quieter types; the choice of quieter transmission and cooling systems. (Source: GILP96a)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > бесшумная технология
См. также в других словарях:
Most — Most … Deutsch Wörterbuch
most — [ moust ] function word, quantifier *** Most is the superlative form of much and many and can be used in the following ways: as an adverb (before an adjective or another adverb): a most interesting lecture the question that is asked most often.… … Usage of the words and phrases in modern English
most — most·lings; most·ly; near·most; neath·most; north·east·ern·most; north·er·most; north·ern·most; north·most; out·er·most; out·most; over·most; pred·most; pri·most; rear·most; right·most; sea·most; south·east·ern·most; south·er·most;… … English syllables
MOST — steht für vergorenen oder unvergorenen Fruchtsaft, siehe Most (Getränk) The Most, eine kanadische Musikgruppe Most (Tschechien) (deutsch Brüx), eine Stadt in der Tschechischen Republik Most, niedersorbische Name der Gemeinde Heinersbrück im… … Deutsch Wikipedia
Most — steht für Fruchtsaft Obstwein in Süddeutschland, der Schweiz und Teilen von Österreich Apfelwein in Wien und den österreichischen Weinanbaugebieten Traubensaft (siehe auch Most (Getränk)) The Most, eine kanadische Musikgruppe Most (Tschechien)… … Deutsch Wikipedia
most — 1. For more and most used in the comparison of adjectives, see adjective 3–4. With adverbs, more and most are normally used when the adverb is formed with ly from an adjective, e.g. most richly, most happily: see er and est forms. The use of most … Modern English usage
Most — (m[=o]st), a., superl. of {More}. [OE. most, mast, mest, AS. m[=ae]st; akin to D. meest, OS. m[=e]st, G. meist, Icel. mestr, Goth. maists; a superl. corresponding to E. more. [root]103. See {More}, a.] 1. Consisting of the greatest number or… … The Collaborative International Dictionary of English
most — [mōst] adj. [ME < OE mast, used as superl. of micel, big (var. of mycel: see MUCH): akin to Goth maists: for IE base see MORE] 1. compar. of MORE 2. greatest in amount, quantity, or degree: used as the superlative of MUCH 3. greatest in number … English World dictionary
Most — Most, adv. [AS. m[=ae]st. See {Most}, a.] In the greatest or highest degree. [1913 Webster] Those nearest to this king, and most his favorites, were courtiers and prelates. Milton. [1913 Webster] Note: Placed before an adjective or adverb, most… … The Collaborative International Dictionary of English
Most — Héraldique … Wikipédia en Français
most — mȏst m <G mȍsta, N mn mòstovi> DEFINICIJA 1. građevina ili objekt koji služi za prelaženje ljudi i tereta preko rijeke, morskog tjesnaca, provalije itd. [pontonski most; viseći most; željeznički most] 2. posebna naprava preko koje se silazi … Hrvatski jezični portal