-
1 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
2 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
3 Naturschutzgebiet
заповедник
Охраняемая территория или акватория, на которой поддерживается в естественном состоянии весь природный или историко-архитектурный комплекс и ведутся научные исследования
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
DE
FR
заповедник природный
Заповедник, являющийся уникальным участком природы
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
DE
FR
национальный заповедник
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
national reserve
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
природный заповедник
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
nature reserve
Areas allocated to preserve and protect certain animals and plants, or both. They differ from national park, which are largely a place for public recreation, because they are provided exclusively to protect species for their own sake. Endangered species are increasingly being kept in nature reserves to prevent them from extinction, particularly in India, Indonesia and some African countries. Natural reserves were used once to preserve the animals that landowners hunted, but, in the 19th century, they became places where animals were kept to prevent them from dying out. Special refuges and sanctuaries are also often designated to protect certain species or groups of wild animals or plants, especially if their numbers and distribution have been significantly reduced. They also serve as a place for more plentiful species to rest, breed or winter. Many parts of the world also have marine and aquatic reserves to protect different species of sea or freshwater plant and animal life. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Naturschutzgebiet
-
4 Wasserversalzung
засоление воды
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
water salination
Process by which water becomes more salty, found especially in hot countries where irrigation is practised. (Source: PHC)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Wasserversalzung
-
5 Nadelwald
хвойный лес
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
coniferous forest
A forest type characterized by cone-bearing, needle-leaved trees. They are generally, but not necessarily, evergreen and relatively shallow-rooted. Since they grow more rapidly than most broad-leaved trees, conifers are extensively planted as a source of softwood timber and pulp. They are tolerant of wide-ranging climatic conditions, of many different types of soil and of considerable differences in terrain. Thus, they are found from the polar latitudes to the tropics, on most types of soils (especially, thin acid soils) and from mountain summits to coastal environments. (Source: WHIT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Nadelwald
См. также в других словарях:
More Fire! Productions — was a women s theatre collective active in New York City from 1980 to 1988. It was founded by Robin Epstein and Dorothy Cantwell and based in the East Village section of lower Manhattan, New York City. More Fire! Productions created and produced… … Wikipedia
More FM — Broadcast area 22 markets in New Zealand Slogan Live it, Love it, Sing it First air date 1991, in Wellington Format Adult contemporary music, Pop music Owner … Wikipedia
More Crap — South Park episode Bono backs Stan up against a wall and tells him he is not gonna be number two in the world s biggest crap record … Wikipedia
Especially for Youth — Saltar a navegación, búsqueda Especially For Youth (normalmente abreviado como EFY) es una semana que está orientada a la juventud en época de seminario, y que se centra en la enseñanza de los principios de la Iglesia de Jesucristo de los Santos… … Wikipedia Español
More Today Than Yesterday: The Greatest Hits Tour — Promotional poster for tour Tour by Diana Ross Start date May 15, 2010 ( … Wikipedia
Especially for Youth — (often abbreviated as EFY) is a week long youth oriented seminar focused on fellowship and teaching the principles of The Church of Jesus Christ of Latter day Saints. Attendance is open to all youth aged 14 to 18. Sessions, which are primarily… … Wikipedia
More pie now — (MPN) is a fictional character originating in the O Reilly comic book series around the late nineteen nineties, but popularized more recently in the manga Southgate, Cutter and Tinman released to a limited audience in late 2005. He is a large… … Wikipedia
More Than Words: The Best of Kevin Kern — Greatest hits album by Kevin Kern Released 2002 … Wikipedia
(more than) your fair share of something — phrase used for emphasizing that an amount is very large, especially an amount of something bad Jean has had her fair share of tragedy. Thesaurus: words used to describe large amounts and quantitiessynonym Main entry: fair * * * ( … Useful english dictionary
more fool somebody (for doing something) — ˌmore fool ˈsb (for doing sth) idiom (informal) used to say that you think that sb was stupid to do sth, especially when it causes them problems • ‘He s not an easy person to live with.’ ‘More fool her for marrying him!’ • ‘I know I shouldn t… … Useful english dictionary
more than you bargained for — more than you bargained for/not what you bargained for/ phrase something different from what you expected, especially something worse The babysitter found she had taken on more than she bargained for. Thesaurus: too much, extra and moresynonym… … Useful english dictionary
