-
1 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
2 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
3 verfügbare Leistung eines Blocks, f
располагаемая мощность агрегата (электростанции)
Установленная мощность генерирующего агрегата (электростанции), за вычетом ограничений его мощности.
[ ГОСТ 19431-84]EN
available capacity of a unit
the maximum power at which a unit can be operated continuously under the prevailing conditions
Note – This power may be gross or net.
[IEV ref 602-03-11]
available capacity of a power station
the maximum power at which a power station can be operated continuously under the prevailing conditions
Note – This power may be gross or net.
[IEV ref 602-03-12]FR
puissance disponible d'une tranche
puissance maximale réalisable en régime continu dans les conditions réelles où une tranche se trouve
Note – Cette puissance peut être brute ou nette.
[IEV ref 602-03-11]
puissance disponible d'une centrale
puissance maximale réalisable en régime continu dans les conditions réelles où une centrale se trouve
Note – Cette puissance peut être brute ou nette.
[IEV ref 602-03-12]Тематики
Синонимы
EN
DE
- verfügbare Leistung eines Blocks, f
- verfügbare Leistung eines Kraftwerks
FR
- puissance disponible d'une centrale
- puissance disponible d'une tranche
- puissance disponible d’une centrale
Немецко-русский словарь нормативно-технической терминологии > verfügbare Leistung eines Blocks, f
-
4 verfügbare Leistung eines Kraftwerks
располагаемая мощность агрегата (электростанции)
Установленная мощность генерирующего агрегата (электростанции), за вычетом ограничений его мощности.
[ ГОСТ 19431-84]EN
available capacity of a unit
the maximum power at which a unit can be operated continuously under the prevailing conditions
Note – This power may be gross or net.
[IEV ref 602-03-11]
available capacity of a power station
the maximum power at which a power station can be operated continuously under the prevailing conditions
Note – This power may be gross or net.
[IEV ref 602-03-12]FR
puissance disponible d'une tranche
puissance maximale réalisable en régime continu dans les conditions réelles où une tranche se trouve
Note – Cette puissance peut être brute ou nette.
[IEV ref 602-03-11]
puissance disponible d'une centrale
puissance maximale réalisable en régime continu dans les conditions réelles où une centrale se trouve
Note – Cette puissance peut être brute ou nette.
[IEV ref 602-03-12]Тематики
Синонимы
EN
DE
- verfügbare Leistung eines Blocks, f
- verfügbare Leistung eines Kraftwerks
FR
- puissance disponible d'une centrale
- puissance disponible d'une tranche
- puissance disponible d’une centrale
Немецко-русский словарь нормативно-технической терминологии > verfügbare Leistung eines Kraftwerks
-
5 ökologische Belastbarkeit
экологическая емкость
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
ecological carrying capacity
1) The maximum number of species an area can support during the harshest part of the year, or the maximum biomass it can support indefinitely. 2) The maximum number of grazing animals an area can support without deterioration. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > ökologische Belastbarkeit
-
6 gegen Überstrom ungeschützter Pol (eines Leistungsschalters)
незащищенный полюс автоматического выключателя
Полюс, не оснащенный максимальным расцепителем тока.
[ ГОСТ Р 50031-99]
незащищенный полюс
Полюс, не оснащенный максимальным расцепителем тока, но в остальном способный функционировать так же, как защищенный полюс того же автоматического выключателя:
а) во исполнение этого требования незащищенный полюс может иметь такую же конструкцию, как один или более защищенных полюсов, или особую конструкцию;
б) если отключающая способность незащищенного полюса иная, чем у одного или более защищенных полюсов, это должно быть оговорено изготовителем
[ ГОСТ Р 50345-99( МЭК 60898-95)]
незащищенный полюс (от сверхтока)
-
[IEV number 442-05-41]EN
unprotected pole
pole without overcurrent release (see 3.3.6), but otherwise generally capable of the same performance as a protected pole of the same circuit-breaker
NOTE 1 - To ensure compliance with this requirement, the unprotected pole may be of the same construction as the protected pole(s), or of a particular construction.
NOTE 2 - If the short-circuit capacity of the unprotected pole is different from that of the protected pole(s), this has to be indicated by the manufacturer.
[IEC 60898-1, ed. 1.0 (2002-01)]
(overcurrent) unprotected pole (of a circuit-breaker)
a pole without overcurrent release, but otherwise generally capable of the same performance as a protected pole of the same circuit-breaker
[IEV number 442-05-41]FR
pôle non protégé
pôle sans déclencheur à maximum de courant (voir 3.3.6), mais, hormis cela, généralement capable des mêmes performances qu'un pôle protégé du même disjoncteur
NOTE 1 - Pour assurer cette prescription, le pôle non protégé peut être de la même construction que le ou les pôles protégés ou d'une construction particulière.
NOTE 2 - Si le pouvoir de coupure du pôle non protégé est différent de celui du ou des pôles protégés ceci sera indiqué par le constructeur
[IEC 60898-1, ed. 1.0 (2002-01)]
pôle (d'un disjoncteur) non protégé contre les surintensités
pôle sans déclencheur à maximum de courant, mais à part cela généralement capable des mêmes performances qu'un pôle protégé contre les surintensités du même disjoncteur
[IEV number 442-05-41]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > gegen Überstrom ungeschützter Pol (eines Leistungsschalters)
-
7 Aufnahmekapazität des Bodens
экологическая емкость земли
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
land carrying capacity
The maximum extent to which ground or soil area may be exploited without degradation or depletion. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Aufnahmekapazität des Bodens
-
8 Kombikraftwerk
тепловая электростанция на различных видах топлива
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
combined cycle-power station
This type of plant is flexible in response and can be built in the 100-600 MW capacity range. It produces electrical power from both a gas turbine (ca. 1300°C gas inlet temperature), fuelled by natural gas or oil plus a steam turbine supplied with the steam generated by the 500°C exhaust gases from the gas turbine. The thermal efficiency of these stations is ca. 50 per cent compared with a maximum of 40 per cent from steam turbine coal fired power stations. This type of plant can be built in two years compared with six years for a coal-fired station and 10-15 years for nuclear. (Source: PORT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Kombikraftwerk
См. также в других словарях:
Maximum Capacity — For the business simulation game, see Maximum Capacity: Hotel Giant. Michael Stanco Ring name(s) Maximum Capacity Max Capacity Monster MAX Cobra The World s Largest Athlete Billed height … Wikipedia
Maximum flow problem — An example of a flow network with a maximum flow. The source is s, and the sink t. The numbers denote flow and capacity. In optimization theory, the maximum flow problem is to find a feasible flow through a single source, single sink flow network … Wikipedia
Capacity factor — The net capacity factor of a power plant is the ratio of the actual output of a power plant over a period of time and its output if it had operated at full nameplate capacity the entire time. To calculate the capacity factor, total the energy the … Wikipedia
capacity — /keuh pas i tee/, n., pl. capacities, adj. n. 1. the ability to receive or contain: This hotel has a large capacity. 2. the maximum amount or number that can be received or contained; cubic contents; volume: The inn is filled to capacity. The… … Universalium
capacity — I. noun (plural ties) Etymology: Middle English capacite, from Middle French capacité, from Latin capacitat , capacitas, from capac , capax Date: 15th century 1. legal competency or fitness < capacity to stand trial > 2. a. the potential or… … New Collegiate Dictionary
capacity — 01. The [capacity] of this elevator is only 500 kilograms. 02. The hospital is filled to [capacity], and patients are having to sleep in beds in the halls. 03. A [capacity] crowd of 17,000 fans were packed into the arena to see the final game of… … Grammatical examples in English
capacity — ca•pac•i•ty [[t]kəˈpæs ɪ ti[/t]] n. pl. ties, adj. 1) the ability to receive or contain: This hotel has a large capacity[/ex] 2) the maximum amount or number that can be received or contained; cubic contents; volume: a jug with a capacity of two… … From formal English to slang
maximum — max|i|mum1 W3S2 [ˈmæksıməm] adj [only before noun] the maximum amount, quantity, speed etc is the largest that is possible or allowed ≠ ↑minimum ▪ The car has a maximum speed of 120 mph. ▪ They made maximum use of the resources available. ▪ To… … Dictionary of contemporary English
Capacity utilization — is a concept in economics and managerial accounting which refers to the extent to which an enterprise or a nation actually uses its installed productive capacity. Thus, it refers to the relationship between actual output that is produced with the … Wikipedia
Maximum life span — is a measure of the maximum amount of time one or more members of a population has been observed to survive between birth and death. Most living species have at least one upper limit on the number of times cells can divide. For humans, this is… … Wikipedia
capacity — ca·pac·i·ty n pl ties 1: a qualification, power, or ability (as to give consent or make a testament) created by operation of law 2: an individual s ability or aptitude; esp: mental ability as it relates to responsibility for the commission of a… … Law dictionary
