-
21 démarrage étoile-triangle
пуск переключением со звезды на треугольник
-EN
star-delta starting
the process of starting a three-phase motor by connecting it to the supply with the primary winding initially connected in star, then reconnected in delta for the running condition
[IEV number 411-52-16]FR
démarrage étoile-triangle
mode de démarrage d'un moteur triphasé à tension réduite, consistant à relier à la source à tension constante les enroulements statoriques, d'abord en couplage étoile, puis à passer au couplage triangle pour le fonctionnement normal
[IEV number 411-52-16]
Magnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Y/Δ changeover node - Узел переключения со звезды на треугольник
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Contactor KΔ - Контактор KΔ
Contactor KY- Контактор KY
Параллельные тексты EN-RU Star-delta Y/Δ starting
Star-delta starting is the best known system and perhaps the commonest starting system at reduced voltage; it is used to start the motor reducing the mechanical stresses and limiting the current values during starting; on the other hand, it makes available a reduced inrush torque.This system can be used for motors with terminal box with 6 terminals and double supply voltage.
It is particularly suitable for no-load starting or with low and constant load torque or lightly increasing load torque, such as in the case of fans or low power centrifugal pumps.
Making reference to the diagram of Figure 6, the starting modality foresees the initial phase with star-connection of the windings to be realized through the closing of the circuit-breaker, of the line contactor KL and of the star contactor KY.
After a suitable predetermined period of time, the opening of the contactor KY and the closing of KΔ allow switching to delta-connection, which is also the configuration of normal running position.
[ABB]Пуск переключением со звезды на треугольник
Пуск переключением со звезды на треугольник является самым известным способом и, возможно, самой распространенной схемой пуска на пониженном напряжении. С одной стороны, этот способ используется для снижения механических нагрузок и ограничения пускового тока, а с другой - обеспечивает уменьшение пускового момента.Такая возможность может быть реализована в двигателях с шестью зажимами в выводной коробке, что позволяет питать его от двух напряжений.
Особенно этот способ подходит для ненагруженного пуска и пуска с низким постоянным или немного увеличивающимся вращающим моментом, например, для пуска вентиляторов или маломощных центробежных насосов.
Схема пуска переключением со звезды на треугольник представлена на рисунке 6. В начальный момент пуска обмотки статора соединяют звездой путем замыкания контактов автоматического выключателя, линейного контактора KL и контактора KY со схемой "звезда".
По истечении заданного времени контакты контактора KY размыкаются и замыкаются контакты контактора КΔ со схемой треугольник.
В результате выполняется переключение обмоток статора со схемы «звезда» на схему «треугольник».
Обе схемы соединения обмоток являются схемами нормального рабочего режима.
[Перевод Интент]Тематики
Обобщающие термины
EN
- star-delta starting
- Y/Δ starting
DE
FR
Франко-русский словарь нормативно-технической терминологии > démarrage étoile-triangle
-
22 bobine d’inductance de limitation de courant
токоограничивающий реактор
-
[ ГОСТ 18624-73]EN
current-limiting reactor
reactor connected in series in a power system to limit the current under system fault conditions
[IEC 60076-6, ed. 1.0 (2007-12)]
series reactor
a reactor intended for series connection in a network, either for limiting the current under fault conditions or for load-sharing in parallel circuits
[IEV ref 421-01-02]FR
bobine d’inductance de limitation de courant
bobine d’inductance connectée en série dans un réseau pour limiter le courant en cas de conditions de défaut dans le réseau
[IEC 60076-6, ed. 1.0 (2007-12)]
(bobine d')inductance série
bobine d'inductance destinée à être placée en série dans un réseau, soit pour limiter le courant dans le cas de défaut dans le réseau, soit pour répartir la charge dans des circuits en parallèle
[IEV ref 421-01-02]Тематики
Классификация
>>>Обобщающие термины
EN
FR
- bobine d’inductance de limitation de courant
Франко-русский словарь нормативно-технической терминологии > bobine d’inductance de limitation de courant
-
23 alimentation stabilisée en tension/courant
источник питания постоянного напряжения и постоянного тока
-
[IEV number 313-04-03]EN
constant voltage/constant current power supply
power supply which operates as a constant voltage or a constant current power supply, depending on load conditions
Source: 551-19-06
[IEV number 313-04-03]FR
alimentation stabilisée en tension/courant
alimentation qui stabilise soit en tension soit en courant, en fonction des conditions de charge
Source: 551-19-06
[IEV number 313-04-03]Тематики
EN
- constant voltage/constant current power supply
DE
FR
- alimentation stabilisée en tension/courant
Франко-русский словарь нормативно-технической терминологии > alimentation stabilisée en tension/courant
-
24 démarrage direct
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Франко-русский словарь нормативно-технической терминологии > démarrage direct
-
25 facteur de régime cyclique
коэффициент циклической токовой нагрузки (кабелей)
Коэффициент, на который может быть умножен номинальный ток установившегося режима, соответствующий коэффициенту нагрузки 100 %, для получения допустимого пикового значения тока в течение суточного цикла, при котором температура токопроводящей жилы в течение этого цикла достигает, но не превышает максимально допустимое значение
[IEV number 461-23-02]EN
cyclic rating factor
factor by which the permissible steady-state rated current corresponding to a 100 % load factor may be multiplied to obtain the permissible peak value of current during a daily cycle such that the conductor attains, but does not exceed, the maximum rated temperature during the cycle
[IEV number 461-23-02]FR
facteur de régime cyclique
facteur par lequel le courant assigné admissible en régime permanent, correspondant à un facteur de charge 100 %, peut être multiplié pour obtenir la valeur de pointe du courant au cours d'un cycle journalier, de sorte qu'au cours de ce cycle, l'âme atteigne sans la dépasser la température assignée maximale
[IEV number 461-23-02]Тематики
- кабели, провода...
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > facteur de régime cyclique
-
26 sélectivité totale
полная селективность
Селективность по сверхтокам, когда при последовательном соединении двух аппаратов защиты от сверхтоков аппарат со стороны нагрузки осуществляет защиту без срабатывания второго защитного аппарата.
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]EN
total discrimination (total selectivity)
over-current discrimination where, in the presence of two or more over-current protective devices in series, the protective device on the load side effects the protection without causing the other protective devices to operate
[IEC 61892-2, ed. 1.0 (2005-03)]FR
sélectivité totale
sélectivité lors d’une surintensité dans laquelle, en présence de deux dispositifs de protection à maximum de courant placés en série, le dispositif de protection aval assure la protection sans provoquer le fonctionnement de l’autre dispositif de protection
[IEC 60947-2, ed. 4.0 (2006-05)]Тематики
EN
FR
Франко-русский словарь нормативно-технической терминологии > sélectivité totale
-
27 fonctionnement en circuit ouvert, m
режим работы в незамкнутой цепи
-
[IEV number 151-15-22]EN
open-circuit operation
no-load operation with zero output current
NOTE – Zero output current can be obtained when the output terminals are not connected to an external electric circuit.
[IEV number 151-15-22]FR
fonctionnement en circuit ouvert, m
fonctionnement hors charge avec un courant de sortie nul
NOTE – Le courant de sortie nul peut être obtenu lorsque les bornes de sortie ne sont pas connectées à un circuit électrique extérieur.
[IEV number 151-15-22]EN
DE
FR
- fonctionnement en circuit ouvert, m
Франко-русский словарь нормативно-технической терминологии > fonctionnement en circuit ouvert, m
-
28 machine asynchrone
асинхронная машина
Бесколлекторная машина переменного тока, у которой отношение частоты вращения ротора к частоте тока в цепи, подключенной к машине, зависит от нагрузок.
[ ГОСТ 27471-87]EN
asynchronous machine
an alternating current machine in which the speed on load and the frequency of the system to which it is connected are not in a constant ratio
[IEV ref 411-31-09]FR
machine asynchrone
machine à courant alternatif dont la vitesse en charge et la fréquence du réseau auquel elle est reliée ne sont pas dans un rapport constant
[IEV ref 411-31-09]Тематики
EN
FR
Франко-русский словарь нормативно-технической терминологии > machine asynchrone
-
29 tension disponible
предельное напряжение
-
[IEV number 314-04-10]EN
compliance voltage
for variable output load transducers having a current output, the value of the output voltage up to which the transducer meets its accuracy specification
[IEV number 314-04-10]FR
tension disponible
pour les transducteurs à charge de sortie variable dont la grandeur de sortie est un courant, valeur de la tension de sortie jusqu’à laquelle le transducteur satisfait sa spécification d’exactitude
[IEV number 314-04-10]Тематики
- измерение электр. величин в целом
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension disponible
-
30 (bobine d')inductance série
реактор последовательного включения
Реактор, включаемый последовательно в фазу сети переменного тока или полюс сети постоянного тока
[ ГОСТ 18624-73]EN
series reactor
a reactor intended for series connection in a network, either for limiting the current under fault conditions or for load-sharing in parallel circuits
[IEV ref 421-01-02]FR
(bobine d')inductance série
bobine d'inductance destinée à être placée en série dans un réseau, soit pour limiter le courant dans le cas de défaut dans le réseau, soit pour répartir la charge dans des circuits en parallèle
[IEV ref 421-01-02]Тематики
Классификация
>>>Обобщающие термины
EN
FR
Франко-русский словарь нормативно-технической терминологии > (bobine d')inductance série
- 1
- 2
См. также в других словарях:
load current — apkrovos srovė statusas T sritis automatika atitikmenys: angl. load current vok. Belastungsstrom, m; Laststrom, m rus. нагрузочный ток, m; ток нагрузки, m pranc. courant de charge, m … Automatikos terminų žodynas
load current — apkrovos srovė statusas T sritis fizika atitikmenys: angl. load current vok. Belastungsstrom, m; Laststrom, m rus. нагрузочный ток, m; ток нагрузки, m pranc. courant de charge, m … Fizikos terminų žodynas
no-load current — tuščiosios veikos srovė statusas T sritis automatika atitikmenys: angl. idle current; no load current; open circuit current vok. Leerlaufstrom, m; Leerstrom, m rus. ток холостого хода, m pranc. courant à vide, m … Automatikos terminų žodynas
Current limiting — is the practice in electrical or electronic circuits of imposing an upper limit on the current that may be delivered to a load with the purpose of protecting the circuit generating or transmitting the current from harmful effects due to a short… … Wikipedia
Load regulation — is the capability to maintain a constant voltage (or current) level on the output channel of a power supply despite changes in load [cite web|title=Line and Load Regulation for Programmable DC Power Supplies and Precision DC Sources Developer… … Wikipedia
Current sense amplifier — Current sense amplifiers (also called current shunt amplifiers) are special purpose amplifiers that output a voltage proportional to the current flowing in a power rail. They utilize a current sense resistor to convert the load current in the… … Wikipedia
Current source — Figure 1: An ideal current source, I, driving a resistor, R, and creating a voltage V A current source is an electrical or electronic device that delivers or absorbs electric current. A current source is the dual of a voltage source. The term… … Wikipedia
Current-to-voltage converter — In electronics, a transimpedance amplifier is an amplifier that converts current to voltage. Its input ideally has zero impedance, and the input signal is a current. Its output may have low impedance, or in high frequency applications, may be… … Wikipedia
Current transformer — A CT for operation on a 110 kV grid In electrical engineering, a current transformer (CT) is used for measurement of electric currents. Current transformers, together with voltage transformers (VT) (potential transformers (PT)), are known as … Wikipedia
Current Communications Group — CURRENT Group Type Limited Liability Company, LLC Industry Energy Sector Founded Germantown, Maryland, U.S. (January 1, 2000 … Wikipedia
Load management — is the process of balancing the supply of electricity on the network with the electrical load.Electrical energy is a form of Energy that cannot be stored. It can however be traded as a commodity. It must be generated, shipped to the point where… … Wikipedia