-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
limit frequency — ribinis dažnis statusas T sritis automatika atitikmenys: angl. boundary frequency; limit frequency; limiting frequency vok. Grenzfrequenz, f rus. граничная частота, f; предельная частота, f pranc. fréquence de coupure, f; fréquence limite, f … Automatikos terminų žodynas
Frequency-hopping spread spectrum — (FHSS) is a method of transmitting radio signals by rapidly switching a carrier among many frequency channels, using a pseudorandom sequence known to both transmitter and receiver. A spread spectrum transmission offers three main advantages over… … Wikipedia
frequency — UK US /ˈfriːkwənsi/ noun [C or U] ► the number of times something happens within a particular period, or the fact of something happening often or a large number of times: »Once a week is a good frequency to back up all the data. the frequency of… … Financial and business terms
Frequency capping — is a term in advertising that means restricting (capping) the amount of times (frequency) a specific visitor to a website is shown a particular advertisement. This restriction is applied to all websites that serve ads from the same advertising… … Wikipedia
Frequency — For other uses, see Frequency (disambiguation). Three cyclically flashing lights, from lowest frequency (top) to highest frequency (bottom). f is the frequency in hertz (Hz), meaning the number of cycles per second. T is the period in seconds (s) … Wikipedia
Frequency allocation — The electromagnetic spectrum is an aspect of the physical world which, like land, water, and air, is subject to usage limitations. Use of radio frequency bands of the electromagnetic spectrum is regulated by governments in most countries, in a… … Wikipedia
Limit — A limit can be: * Limit (mathematics), including: ** Limit of a function ** Limit of a sequence ** One sided limit ** Limit superior and limit inferior ** Limit of a net ** Limit point ** Limit (category theory) * A constraint (mathematical,… … Wikipedia
Frequency management challenges in military forces — Every military force has a goal to ensure and have permanent access in the spectrum of radio frequencies to meet its vital military tasks. This is based on strategies, doctrines and different policies that military forces adhere to.The nature of… … Wikipedia
Frequency probability — Statistical probability redirects here. For the episode of Star Trek: Deep Space Nine, see Statistical Probabilities. John Venn Frequency probability is the interpretation of probability that defines an event s probability as the limit of its… … Wikipedia
Frequency extender — In broadcast engineering, a frequency extender is an electronic device that allows high fidelity analogue audio to be sent over regular POTS telephone lines, without the loss of higher audio frequencies (treble). It is an extended concept of a… … Wikipedia
frequency theory of probability — The view developed by Richard von Mises (1883–1953), in his Probability, Statistics, and Truth (1957; 1st German edn., 1928) that the probability of an event in a situation can be defined in terms of the frequency of occurrence of events of the… … Philosophy dictionary
