-
1 колонка с рычагами управления
Automobile industry: lever control connector, lever control consoleУниверсальный русско-английский словарь > колонка с рычагами управления
-
2 усилие (сила)
force
- (сила, потребная для перемещения органа управления ла) — control force
- (давление или нагрузка, создаваемая на органе управления ла) — pressure, load
-, большое (на рычаге управления) — heavy (control) force
-, возникающее на поверхности управления — force exerted on control surface
-, загрузочное (создаваемое автоматом усилий или загрузочным механизмом) — (artificial) feel
усилие, создаваемое механизмами, включенными в необратимую (бустерную) систему управления ла, при которой усилие (нагрузка) на поверхность управления не ощущается на органах управления, расположенных в кабине экипажа. — a control feel simulated by mechanisms incorporated in the control system of an aircraft where the forces acting on the control surfaces are not transmitted to the cockpit controls, as in the case of an irreversible control system or a power-operated system.
- летчика (прикладываемое к органу управления) — pilot-applied force
- летчика, физическое — pilot's (physical) effort
при наличии гидроусилителей отклонение поверхностей управления не требует физических усилий со стороны летчика. — power-operated controls are moved hydraulically with the pilot's physical effort making no contribution.
- механизма загрузки (руля высоты) — (elevator) feel load
- (летчика) на органах управления — pilot control force, pilot force (for controls)
the pilot control force of the ailerons is provided by a load feel mechanism.
- на органах управления, предельное — limit pilot force
предельные усилия на педалях управления рн не должны превышать 60 кг, на ручке (штурвальной колонке) - 45 кг при продольном н 30 кг при поперечном управлении, и 45 кг на штурвале. — the limit pilot forces are as follows: for foot controls, 130 pounds, for stick controls, 100 pounds fore and aft and 67 pounds laterally, for wheel controls, 100 pounds.
- на органах управления, создаваемое летчиком — pilot-applied force the design loads resulting from 0.60 of the pilot-applied forces are acceptable minimum design loads.
- на педалях — pedal force
усилие на педалях не должно превышать 80 кг. — rudder pedal force of 180 pounds need not be exceeded.
- на поверхности управления (напр., рв, снимаемое триммерам) — control surface (elevator) pressure (relieved by using trim tab)
- на руле высоты (нагрузка, вызывающая кабрирование) — backpressure on elevator (to rise nose)
- на ручке управления — stick force
усилие, которое необходимо приложить к ручке (штурвалу) управления самолетом при отклонении руля высоты (элеронов) на заданный угол при данной скорости полета. — a force required to be applied to the stick (control column, wheel) to deflect the elevator (ailerons) through a desired angle at a given speed.
- на ручке управления в направлении на себя — back pressure on control stick relieve the back pressure on the stick.
- на ручке управпения (или штурвале) в направлении от себя — control stick (or wheel) for-ward pressure
- на ручке управления, небольшое — low stick force (load, pressure)
- на ручке от руля высоты (элеронов) — stick force /pressure/ caused from movement of elevator (ailerons)
- на ручке управления (или штурвале), толкающее ("от себя") — control stick (or wheel) forward pressure
- на ручке управления (или штурвале), тянущее ("на себя") — control stick (or wheel) back pressure
- на штурвале (создаваемое внешней аэродинамической нагрузкой на рв) — control column pressure /load/ relieve the control column (or elevator) pressure by the elevator trim tab.
- на штурвале (по крену) — aileron control wheel force /pressure/
- на штурвале (по тангажу) — elevator control column /wheel/ force /pressure/
- на штурвале на единицу перегрузки — control column force per unit of normal acceleration
- от руки — manual effort
при сборке деталей требуется небольшое усилие от руки. — slight manual effort is required to assemble the parts.
- от руля высоты — elevator pressure
- от элерона — aileron pressure
- перекладки рычага (переключателя) управления — (switch) lever actuating force
- пересиливания (рулевых машинок автопилота) — pilot overpower
- при размыкании и замыкании контактов штепсельного разъема — connector contacts engagement and separation force
- пружинного механизма загрузки (в системе управления ла) — (artificial) spring feel load
- пружины — spring force
-, рабочее (на валу) — (shaft) operating torque
- разъема шр(дпя рассоединения) — connector contacts separation force
-, тормозное — braking force
-, тяговое — tractive force
-, тяговое (при буксировке) — tawing force
-, тянущее (на ручке управления или штурвале) — backpressure
- управления — control force
(пере)балансировать самолет для снятия усилий с руля высоты — (re)trirn aircraft to reduce pressure on elevator
не прикладывать большого — do not strain tool by tightening
у. при затяжке гайки (винта) — nut (screw) severely
предупреждение: не прилагать значительных у. — caution: do not force.
передавать у. (нагрузку) — transmit load
передавать у. (механизма, человека) — transmit effort
преодолевать у. (пружины) — overcome spring force
прикладывать у. к... — apply force to...
регулировать у. (руля высоты) триммером — adjust elevator trim tab to relieve elevator pressure
снимать. у. с органа управления — relieve /relax/ control pressure, trim out control force /pressure/
снимать у. с (рв или рн) триммированием — relieve /relax/ (elevator, ruder) pressure by adjusting trim control
создавать у. — create /produce/ force /load, pressure/
создавать у. на руле высоты взятием штурвала на себя — apply backpressure on elevator
увеличивать у. на руле высоты (отклонением рв вверх) — increase back elevator pressureРусско-английский сборник авиационно-технических терминов > усилие (сила)
-
3 переключатель
1) General subject: commutator, key, relay, switch, throw over2) Computers: option button3) Aviation: switch change over4) Medicine: selector (в приборе)5) Military: (change-over) (света фар) dimmer, (change-over) selector switch, (change-over) switch6) Engineering: change switch, changer (с одного режима на другой), chopper switch, circuit changer, commutator (на несколько положений), interchanging switch, reverser, reversing switch, select dial (программ), selection valve, selection valve group, selector (на несколько положений), selector control, selector control valve, selector group, selector switch (на несколько положений), selector valve, selector valve group, switch group, switch key, switching key, switching unit, throw-over switch, enable switch7) Construction: change-over switch, selector switch8) Railway term: changing switch, commutation switch, current reverser9) Automobile industry: changer, doubler (электрический), shifter10) Polygraphy: autochanger11) Telecommunications: change-tune switch (диапазонов частот), selector knob, switching gate, transfer contact12) Electronics: permutator13) Information technology: anticoincidence switch, communicator, jumper, radio button, switch box, toggle button, toggle switch (перекидной), transfer table, tumbler switch (перекидной)14) Oil: shift knob, switcher, switchgear, toggle15) Special term: throw-over16) Astronautics: changeover lever, channel selector, connector17) Mechanics: changeover switch18) Drilling: on-off switch19) Network technologies: SW20) Automation: actuator, changeover gate, keyer, knob21) Robots: tumbler22) Arms production: fire control lever23) General subject: actuation selector switch, switch (или переключает между несколькими положениями)24) Chemical weapons: switching device25) Bicycle: changer ("перекидка"; то же, что derailleur и jumper), derailleur ("перекидка"; то же, что changer и jumper), jumper ("перекидка"; то же, что changer и derailleur)26) Tengiz: changeover switch (рычажный), switch hook (рычажный)27) Electrical engineering: transfer (на другой источник питания), contractor -
4 узел (агрегат, блок)
assembly, unit
ряд деталей или подузлов, соединенных вместе для выполнения определенной функции. — а number of parts or subassemblies or any combination thereof joined together to perform a specific function.
- (единица скорости) морская миля (1852 м в час) — knot (к, kt) а nautical mile per hour.
- (изделие) количество деталей на изделие (графа таблицы). — assembly (assy) units per assy.
- (составная часть агрегата, блока, установки) — sub-assembly, subassembly
две или более деталей, о6разующих часть агрегата (сборки) или блока и заменяемых как одно целое, но включающее деталь (детали), подлежащие индивидуальной замене. — two оr more parts which form а portion of an assembly or а unit replaceable as а whole, but having а part or parts which are individually replaceable.
- а (обозначение на чертеже) — detail а
- (часть) агрегата — sub-assembly, assembly
the distinction between an assembly and sub-assembly is not always exact.
- баков (масляных) (блок) — oil tank assembly
два отдельных бака установлены в одном узле. — two separate tanks are housed within the tank assembly.
-, гиростабилизированный, на карданном подвесе — gyro stabilized gimbal assembly
- гироскопа — gyro assembly
- дозирующей иглы (топлива) — throttle valve assembly
-, законченный (конструктивно) — definite-purpose assembly
-, качающий — pumping unit
насос имеет два отдельных качающих узла, состоящих из блока плунжеров, вращающихся no скошенной пяте. — the pump has two independent pumping units consisting of pfunger rotating assembly working against a variable angle swash plate.
- клапана (поддержания) постоянного (пропорционального) перепада давлений (насоса-регулятора) — proportioning valve unit
- компрессора (двиг.) — compressor section
- компрессора (подраздел 72-30) — compressor section
- контроля (блока питания) — monitoring device
работа основана на сравнении контролируемых напряжений с эталонными.
- крепления — attach(ment) fitting
- крепления груза (на борту ла) — cargo tie-down fitting
- крепления двигателя — engine mounting attachment
узлы крепления двигателя и конструкция, несущая эти узлы, должны выдерживать указанные нагрузки без разрушения, поломки или остаточной деформации. — the engine mounting attachments and related structure must be able to withstand the specified loads without failure, malfunction, or permanent deformation.
- крепления закрылка — flap attach(ment) fitting
- крепления крыла — wing attachment fitting
узлы служат для крепления крыла к фюзеляжу. — the fittings on the wing used to attach the wing to the fuselage.
- крепления оси колес (к стойке шасси) — wheel axle attachment fitting
- крепления руля высоты (или направления) — elevator (or rudder) hinge /attach/ fitting
- крепления опоры шасси, (передний, задний) — (forward, aft) landing gear strut attachment fitting
- крепления страховочных строп (или троса) — safety harness (or line) attach(ment) point /receptacle/
- крепления, шарнирный — hinge fitting
- крепления элерона — aileron hinge /attach/ fitting
-, магнито-индукционный (тахометра) — magnetic-drag assembly
-, манометрический — pressure capsule assembly
-, манометрический (трубка бурдона) — bourdon tube assembly
-, мембранный — (pressure) capsule assembly
- мембранный (указателя скорости) — airspeed capsule
- навески (общий термин) — attach(ment) fitting
узлы, служащие для крепления стабилизатора, руля высоты, триммеров, обтекателей. — the fittings on the stabilizers used for attachment of stabilizers, elevators, rudder tabs, fillets/fairings.
- навески (шарнирный) (рис. 10) — hinge fitting
- навески закрылка — flap attach(ment) fitting
- навески руля высоты (направления или элерона) — elevator (rudder or aileron) hinge fitting
- навески руля направления, верхний (нижний) — rudder top (bottom) hinge fitting
- навески руля высоты (или элерона), внешний — elevator (or aileron) outboard hinge fitting
- навески руля высоты (или элерона), внутренний (корневой) — elevator (or aileron) inboard hinge fitting
- навески руля (или элерона), средний — elevator (оr aileron) center hinge fitting
- навески триммера — trim tab hinge fitting
- навески шасси — landing gear (shock strut) attachment fitting
- насоса, управляющий — pump controlling section
- ограничения (раскрутки) оборотов (насоса-регулятора) — overspeed limiting control
- основной дозирующей иглы (командно-топливного агрегата или насоса-регулятора) — throttle valve (sub-) assembly (of fuel flow control unit)
- плунжерный качающий (наcoca) — plunger rotating assembly
- поворота крыла (в горизонтальной плоскости) — wing pivot (assembly)
- подвески вооружения на пилоне — weapon-pylon base
- подвески двигателя — engine mount
каркас, поддерживающий двигатель и крепящий его к мотогондоле или пилону. — the framework which supports an engine and attach it to the nacelle or pylon.
-, поршневой (узел цилиндров тормоза колеса) — cylinder assembly
- приемника-процессора, электронный — receiver-processor electronic assembly
- прямой (завязки шнуров, тросов) — square knot
- разъема коммуникаций, унифицированный (уурк) — combined services connector
- растормаживания (тормоза колеса) — (brake) retraction mechanism
для возвращения (после снятия давления в тормозе) нажимного диска в исходное положение, т.е. для растормаживания колеса. — the brake has automatic adjustment, integral with the retraction mechanism built into each piston, movement of the piston compresses the retraction springs.
-, регулируемой подпитки (топливом гтд) — variable enrichment unit
-, рифовый (завязки строп) — reef knot
-, рычажно-кулачковый (дозир. иглы) — throttle valve cam and lever assembly
-, силовой (блок цилиндров тормоза колеса) — cylinder assembly
-, скоростной (указателя скорости) — airspeed capsule
-, страховочный (для крепления страховочного троса или ремня) — safety rоре (or belt) attach fitting /point/
-, стыковой (стыковочный) (рис. 16) — attachment fitting
-, такелажный (точка подъема) (рис. 10) — hoist point
- такелажный (деталь) — hoist fitting
- турбины — turbine section
состоит из ступеней высок. и низк. давлений, приводящих во вращение соответствующие компрессоры. — consists of hp and lp stages, each driving their own compressors through concentric shafts.
- турбины (подраздел 72 - 50) — turbine section
- турбины и реактивного сопла — turbine and exhaust section /unit/
- (-) удавка (завязки шнуров, тросов) — running knot, slip knot
- управления и блокировки реверса тяги (насоса-регулятора) — thrust reverser control and interlocking unit
- управления приемистостью (топливного насоса-регулятора) — acceleration control (unit)
-, функционально законченный — definite-purpose assembly
- цилиндров (блок тормоза колеса) — cylinder assembly
-, швартовочный (груза на борту ла) — tie-down fitting
-, швартовочный (швартовый, ла) (рис. 150) — mooring fitting
- штока амортизатора (шасси), нижний — shock strut piston lower fitting
- электро-гидравлический /электро-гидромеханический / (гидроусилителя) — electro-hydraulic unit
командные эл. сигналы подаются в электрогидравлический узел гидроусилителя (бустера), в котором они преобразуются в механическое перемещение соответствующих золотников. — autocontrol demands are signalled electrically to the electrohydraulic unit on each surface drive (hydraulic booster) which converts them to mechanical movements (of corresponding slide valves)
завязывать у. — tie a knot
развязывать у. — loose a knot
определять дефект в у. (точнo устанавливать отказавший узел) — isolate the trouble into sub-assemblyРусско-английский сборник авиационно-технических терминов > узел (агрегат, блок)
См. также в других словарях:
Roland Fantom-G — Fantom G is a series of music production workstation keyboards developed by Roland Corporation that debuted in the Winter NAMM 2008. Featuring a 8.5 LCD display, 128 polyphony and USB audio/MIDI/flash support, it is the successor of the Fantom X … Wikipedia
Diving regulator — and Octopus Other names Demand valve Uses Reduces pressurized breathing gas to ambient pressure and delivers it to the diver Inventor Manuel Théodore Guillaumet (1838), Benoît Rouquayrol (1860) … Wikipedia
IBM PC keyboard — The keyboards for IBM PC compatible computers are standardized. However, during the 3 plus decades of PC architecture being constantly updated, multiple types of keyboard layout variations have been developed. A well known class of IBM PC… … Wikipedia
Friden Flexowriter — The Friden Flexowriter, or flexowriter as on its nameplate, was a teleprinter, a heavy duty electric typewriter capable of being driven not only by a human typing, but also automatically by several methods including direct attachment to a… … Wikipedia
Glock pistol — Infobox Weapon name=Glock caption=The Glock 17 (recent production model) origin=flag|Austria type=Semi automatic pistol is ranged=yes service=1980–present used by=See Users wars= designer=Gaston Glock design date=1980 manufacturer=Glock GmbH unit … Wikipedia
History of the single-lens reflex camera — The history of the single lens reflex camera predates the invention of photography in 1826/27 by one and a half centuries with the use of a reflex mirror in a camera obscura first described in 1676. Such SLR devices were popular as drawing aids… … Wikipedia
Military equipment of Turkey — The military equipment of Turkey includes a wide array of arms, artilleries, large surface vessels, cannons, armored vehicles, mortars, unmanned vehicles and many different equipments. Contents 1 Historical development 1.1 General 1.2 1923 1950 … Wikipedia
Headlamp — Headlight redirects here. For other uses, see Headlight (disambiguation). High Beams redirects here. For the urban legend also known by that name, see Killer in the backseat. A motor scooter s front with an impractical number and variety of… … Wikipedia
Fly system — Fly loft of the Theater Bielefeld in Germany A fly system, flying system or theatrical rigging system, is a system of lines (e.g. ropes), blocks (pulleys), counterweights and related devices within a theatre that enable a stage crew to quickly,… … Wikipedia
Glossary of rail terminology — Rail transport Operations Track Maintenance High speed Gauge Stations … Wikipedia
Electric guitar — Fender Stratocaster String instrument Classification String instrument (plucked, either by fingerpicking, or with a pick.) … Wikipedia