-
1 линейное преобразование
линейное преобразование
-
[IEV number 314-02-04]EN
linear conversion
conversion for which the quotient of each change in the output value by the corresponding change in the input value is intended to be constant
[IEV number 314-02-04]FR
conversion linéaire
conversion telle que le quotient de chaque changement de la valeur de sortie par le changement correspondant de la valeur d'entrée soit constant
[IEV number 314-02-04]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > линейное преобразование
-
2 нелинейное преобразованиеических величин
нелинейное преобразование
-
[IEV number 314-02-05]EN
non-linear conversion
conversion for which the quotient of each change in the output value to the corresponding change in the input value is not constant
[IEV number 314-02-05]FR
conversion non linéaire
conversion telle que le quotient de chaque changement de la valeur de sortie par le changement correspondant de la valeur d'entrée n'est pas constant
[IEV number 314-02-05]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > нелинейное преобразованиеических величин
-
3 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
-
4 входное полное сопротивление
входное полное сопротивление
-
[IEV number 312-06-18]EN
input impedance
impedance of the input circuit measured between the input terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the input circuit is such that the instantaneous value of the current flowing into the input terminals is a non-linear function of the instantaneous value of the input voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual input circuit, is sometimes called the "equivalent input impedance".
[IEV number 312-06-18]FR
impédance du circuit d'entrée
impédance du circuit d'entrée entre les bornes d'entrée dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit d'entrée est tel que la valeur instantanée du courant traversant les bornes d'entrée est une fonction non linéaire de la valeur instantanée de la tension d'entrée dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit d'entrée réel, est parfois appelée "impédance équivalente d'entrée".
[IEV number 312-06-18]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > входное полное сопротивление
-
5 значение величины срабатывания (возврата) электрического реле
значение величины срабатывания (возврата) электрического реле
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
[ ГОСТ 16022-83]EN
switching value
the value of the input energizing quantity (or characteristic quantity) at which a relay switches under specified conditions
NOTE – These specified conditions can be expressed by using one of the adjectives defined under the items 446-13-27 to 446-13-29.
[IEV number 446-13-24]FR
valeur de commutation
valeur de la grandeur d'alimentation d'entrée ou de la grandeur caractéristique, pour laquelle un relais commute dans des conditions spécifiées
NOTE – Ces conditions spécifiées peuvent être exprimées par l'un des qualificatifs définis de 446-13-27 à 446-13-29.
[IEV number 446-13-24]Тематики
Классификация
>>>EN
DE
FR
71. Значение величины срабатывания (возврата) электрического реле
D. Ansprechwert
Е. Operate value
F. Valeur de fonctionnement
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > значение величины срабатывания (возврата) электрического реле
-
6 время устойчивого замыкания (размыкания) контакта электрического реле
- Temps de fermeture (d’ouverture) stable
- temps de fermeture (d'ouverture) stable
время устойчивого замыкания (размыкания) контакта электрического реле
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
[ ГОСТ 16022-83]EN
time to stable closed condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is closed and fulfils specified requirements
[IEV number 446-17-24]
time to stable open condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is open and fulfils specified requirements
[IEV number 446-17-25]FR
temps de fermeture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est fermé et répond aux prescriptions spécifiées
[IEV number 446-17-24]
temps d'ouverture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est ouvert et répond aux prescriptions spécifiées
[IEV number 446-17-25]
Тематики
EN
DE
FR
136. Время устойчивого замыкания (размыкания) контакта электрического реле
D. Ansprech-Rückfallzeit
Е. Time to stable closed (open) condition
F. Temps de fermeture (d’ouverture) stable
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > время устойчивого замыкания (размыкания) контакта электрического реле
-
7 входная полная проводимость биполярного транзистора в режиме малого сигнала
- Valeur de l’admittance d’entrée, sortie en court-circuit pour de petits signaux
- valeur de l'admittance d’entrée, sortie en court-circuit pour de petits signaux
входная полная проводимость биполярного транзистора в режиме малого сигнала
Отношение изменений комплексных величин входного тока к вызванному им изменению напряжения на входе при коротком замыкании по переменному току на выходе.
Обозначение
y11
y11
Примечание
В схеме с общей базой или общим эмиттером добавляется индекс соответственно "б" или "э" для отечественных буквенных обозначений и "b" и "е" для международных обозначений.
[ ГОСТ 20003-74]Тематики
EN
DE
FR
- valeur de l'admittance d’entrée, sortie en court-circuit pour de petits signaux
21. Входная полная проводимость биполярного транзистора в режиме малого сигнала
D. Komplexer Kleinsignaleingangsleitwert
E. Small-signal value of the short-circuit input admittance
F. Valeur de l’admittance d’entrée, sortie en court-circuit pour de petits signaux
y*11
Отношение изменений комплексных величин входного тока к вызванному им изменению напряжения на входе при коротком замыкании по переменному току на выходе
Источник: ГОСТ 20003-74: Транзисторы биполярные. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-французский словарь нормативно-технической терминологии > входная полная проводимость биполярного транзистора в режиме малого сигнала
-
8 входное сопротивление биполярного транзистора в схеме с общим эмиттером в режиме большого сигнала
- valeur statique de la résistance d’entrée
входное сопротивление биполярного транзистора в схеме с общим эмиттером в режиме большого сигнала
Отношение напряжения на входе транзистора к входному току при заданном постоянном обратном напряжении коллектор-эмиттер в схеме с общим эмиттером.
Обозначение
h11Э
h11E
[ ГОСТ 20003-74]Тематики
EN
FR
- valeur statique de la résistance d’entrée
19. Входное сопротивление биполярного транзистора в схеме с общим эмиттером в режиме большого сигнала
E. Static value of the input resistance
F. Valeur statique de la résistance d’entrée
h11Э
Отношение напряжения на входе транзистора к входному току при заданном постоянном обратном напряжении коллектор-эмиттер в схеме с общим эмиттером
Источник: ГОСТ 20003-74: Транзисторы биполярные. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-французский словарь нормативно-технической терминологии > входное сопротивление биполярного транзистора в схеме с общим эмиттером в режиме большого сигнала
-
9 нормируемый параметр невозврата электрического реле
нормируемый параметр невозврата электрического реле
Значение входной воздействующей или характеристической величины, при котором электрическое реле не должно возвращаться
[ ГОСТ 16022-83]EN
non-release value
the value of the input energizing quantity (or characteristic quantity) at which a relay does not release under specified conditions
NOTE – These specified conditions can be expressed by using one of the adjectives defined under the items 446-13-27 to 446-13-29.
[IEV number 446-13-18 ]FR
valeur de non-relâchement
valeur de la grandeur d'alimentation d'entrée ou de la grandeur caractéristique pour laquelle un relais ne relâche pas dans des conditions spécifiées
NOTE – Ces conditions spécifiées peuvent être exprimées par l'un des qualificatifs définis de 446-13-27 à 446-13-29.
[IEV number 446-13-18 ]Тематики
Классификация
>>>EN
DE
FR
74. Нормируемый параметр невозврата электрического реле
D. Haltwert
Е. Non-release value
F. Valeur de non relâchement
Значение входной воздействующей или характеристической величины, при котором электрическое реле не должно возвращаться
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > нормируемый параметр невозврата электрического реле
-
10 преобразователь среднего значения величины
преобразователь среднего значения величины
-
[IEV number 313-03-08]EN
mean-sensing transducer
transducer which measures the mean value of a full wave rectified input waveform and which is adjusted so that the output corresponds to the r.m.s. input when the input is sinusoidal
[IEV number 313-03-08]FR
transducteur de valeur moyenne
transducteur qui mesure la valeur moyenne d'une onde d’entrée redressée en double alternance, et qui est ajusté de façon à donner une sortie correspondant à la valeur efficace de l’entrée quand cette entrée est sinusoïdale
[IEV number 313-03-08]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > преобразователь среднего значения величины
-
11 время дифференцирования
время предварения
время дифференцирования
Время, в течение которого входной сигнал, изменяющийся с постоянной скоростью, достигнет значения выходного сигнала, изменяющегося с той же скоростью, в момент начала отсчета.
[ ГОСТ 9988-84]EN
derivative action time
for a derivative element the same as the derivative action coefficient, if its input and output variables have the same unit
Note 1 – Then the derivative action time is given by TD = KD, where KD is the derivative action coefficient.
Note 2 – The derivative action time can also be given as the duration of the time interval that a rampwise variation of the input variable needs to reach the same value as the stepwise varying output variable.
[IEV ref 351-28-26]FR
constante de temps de dérivation
pour un élément à action par dérivation, la constante de temps de dérivation est égale au coefficient d'action par dérivation, si ses variables d'entrée et de sortie sont dans la même unité
Note 1 – La constante de temps de dérivation est alors donnée par TD = KD, où KD est le coefficient d'action par dérivation.
Note 2 – La constante de temps de dérivation peut également être donnée comme la durée de l'intervalle de temps nécessaire pour qu'une variation en rampe de la variable d'entrée atteigne la même valeur que la variable de sortie correspondante.
[IEV ref 351-28-26]Тематики
- автоматизация, основные понятия
Синонимы
EN
DE
- Differenzierzeit, f
FR
Русско-французский словарь нормативно-технической терминологии > время дифференцирования
-
12 время интегрирования
время интегрирования
Время, в течение которого интегральная составляющая регулятора изменяет выходной сигнал на значение, равное значению скачкообразного изменения входного сигнала.
[ ГОСТ 9988-84]EN
integral action time
for an integral element, the reciprocal of the integral action coefficient, if its input and output variables have the same unit
Note 1 – The integral action time then is given by
TI=1/KI
where KI is the integral action coefficient.
Note 2 – The integral action time can also be given as that duration of the time interval which the output variable needs to reach the same value as a stepwise variation of the input variable.
[IEV ref 351-28-21]FR
constante de temps d'intégration
pour un élément à action par intégration, inverse du coefficient d'action par intégration, si ses variables d'entrée et de sortie sont dans la même unité
Note 1 – La constante de temps d'intégration est alors donnée par
TI=1/KI
où KI est le coefficient d'action par intégration.
Note 2 – La constante de temps d'intégration peut également être donnée comme la durée de l'intervalle de temps nécessaire pour que la variable de sortie atteigne la même valeur qu'une variation en échelon de la variable d'entrée.
[IEV ref 351-28-21]Тематики
- автоматизация, основные понятия
EN
DE
- Integrierzeit, f
FR
Русско-французский словарь нормативно-технической терминологии > время интегрирования
-
13 входное напряжение
- Udin
- tension d’entrée déclarée
входное напряжение
Udin
Напряжение, определяемое напряжением в системе электроснабжения и коэффициентом преобразования измерительного преобразователя.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
declared input voltage
Udin
value obtained from the declared supply voltage by a transducer ratio
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension d’entrée déclarée
Udin
valeur obtenue à partir de la tension d’alimentation déclarée d’un rapport de transformation
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
Синонимы
EN
FR
- tension d’entrée déclarée
- Udin
Русско-французский словарь нормативно-технической терминологии > входное напряжение
-
14 коэффициент подавления общего вида
коэффициент подавления общего вида
-
[IEV number 312-06-21]EN
common mode rejection ratio
CMRR (abbreviation)
ratio of the voltage applied between a specified reference point and the input terminals, when connected together by a specified circuit, to the voltage required between the input terminals to produce the same value of the output
NOTE 1 – The common mode rejection ratio is usually expressed in decibels and can depend on the frequency, the waveform and the method of measurement.
NOTE 2 – Common mode rejection ratio can also apply to quantities other than voltage.
[IEV number 312-06-21]FR
rapport de réjection de mode commun
rapport de la tension appliquée entre un point de référence spécifié et les deux bornes d'entrée connectées l'une à l'autre par un circuit spécifié, à la tension nécessaire entre les bornes d'entrée pour produire la même valeur de sortie
NOTE 1 – Le facteur de réjection de mode commun est généralement exprimé en décibels et peut dépendre de la fréquence, de la forme d’onde et de la méthode de mesure.
NOTE 2 – Le rapport de réjection de mode commun peut aussi s'appliquer à des grandeurs autres que les tensions.
[IEV number 312-06-21]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > коэффициент подавления общего вида
-
15 аналоговый (измерительный) прибор
аналоговый (измерительный) прибор
аналоговый показывающий прибор
-
[IEV number 312-02-09]EN
analogue (measuring) instrument
analogue indicating instrument
measuring instrument whose indication is a continuous function of the corresponding value of the measurand or of the input signal
NOTE – This term relates to the form of presentation of the indication, not to the principle of operation of the instrument.
Source: ≈ VIM 4.10
[IEV number 312-02-09]FR
appareil de mesure (à affichage) analogique
appareil (de mesure) analogique
appareil de mesure dont l'indication est une fonction continue de la valeur correspondante du mesurande ou du signal d’entrée
NOTE – Ce terme se rattache à la forme de présentation de l’indication, non au principe de fonctionnement de l’appareil.
Source: ≈ VIM 4.10
[IEV number 312-02-09]Тематики
- измерение электр. величин в целом
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > аналоговый (измерительный) прибор
-
16 время замыкания замыкающего контакта электрического реле
- Temps d’etablissement d’un contact de travail
- temps d'etablissement d'un contact de travail
время замыкания замыкающего контакта электрического реле
Время от момента, когда входная воздействующая величина электрического реле, находящегося в начальном состоянии, принимает в заданных условиях определенное значение, до момента, когда замкнется в первый раз замыкающий контакт
[ ГОСТ 16022-83]EN
closing time of a make contact
for a relay which is in the release condition, the time interval between the instant a specified value of the input energizing quantity is applied under specified conditions and the instant when the make contact first closes
[IEV number 446-17-03]FR
temps d'établissement d'un contact de travail
pour un relais qui est dans un état de repos, temps écoulé entre l'instant où la grandeur d'alimentation d'entrée prend, dans des conditions spécifiées, une valeur définie et l'instant où s'établit pour la première fois le contact de travail
[IEV number 446-17-03]Тематики
EN
DE
FR
119. Время замыкания замыкающего контакта электрического реле
D. Ansprechzeit eines Schliessers
E. Closing time of a make contact
F. Temps d’etablissement d’un contact de travail
Время от момента, когда входная воздействующая величина электрического реле, находящегося в начальном состоянии, принимает в заданных условиях определенное значение, до момента, когда замкнется в первый раз замыкающий контакт
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > время замыкания замыкающего контакта электрического реле
-
17 время срабатывания электрического реле
- tеmрs d'action pour relais de tout ou rien
- Temps de fonctionnement;
- temps de fonctionnement
время срабатывания электрического реле
Время от момента, когда входная воздействующая или характеристическая величина электрического реле, находящегося в начальном или исходном состоянии, принимает в заданных условиях определенное значение до момента, когда реле завершает срабатывание
[ ГОСТ 16022-83]EN
operate time
for a relay which is in the release condition (initial condition) the time interval between the instant a specified value of the input energizing quantity (characteristic quantity) is applied under specified condition and the instant when the relay switches
NOTE – This term is used only when the relay has output circuits of the same type and no precision is required according to contact time difference.
[IEV number 446-17-09]FR
temps de fonctionnement
temps d'action (terme déconseillé, utilisé pour les relais de tout ou rien)
pour un relais qui est dans l'état de repos ou dans un état initial, temps écoulé entre l'instant où la grandeur d'alimentation d'entrée ou la grandeur caractéristique prend, dans des conditions spécifiées, une valeur définie et l'instant où le relais commute
NOTE – Ce terme n'est utilisé que lorsque le relais ne comporte que des circuits de sortie de même nature et qu'aucune précision n'est nécessaire quant à la dispersion des temps de contact.
[IEV number 446-17-09]Тематики
EN
DE
FR
122. Время срабатывания электрического реле
D. Betätigungszeit
E. Operate time
F. Temps de fonctionnement;
Temps d’action (pour relais de tout ou rien)
Время от момента, когда входная воздействующая или характеристическая величина электрического реле, находящегося в начальном или исходном состоянии, принимает в заданных условиях определенное значение до момента, когда реле завершает срабатывание
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > время срабатывания электрического реле
-
18 входное сопротивление биполярного транзистора в режиме малого сигнала
- valeur de l’impédance d’entrée, sortie en court-circuit pour de petits signaux
входное сопротивление биполярного транзистора в режиме малого сигнала
Отношение изменения напряжения на входе к вызвавшему его изменению входного тока в режиме короткого замыкания по переменному току на выходе транзистора.
Обозначение
h11
Примечание
В схеме с общей базой или общим эмиттером добавляется индекс соответственно "б" или "э" для отечественных буквенных обозначений и "b" и "е" для международных обозначений.
[ ГОСТ 20003-74]Тематики
EN
DE
FR
- valeur de l’impédance d’entrée, sortie en court-circuit pour de petits signaux
Русско-французский словарь нормативно-технической терминологии > входное сопротивление биполярного транзистора в режиме малого сигнала
-
19 преобразователь среднеквадратичных значений
преобразователь среднеквадратичных значений
-
[IEV number 313-03-09]EN
rms-sensing transducer
transducer specifically designed to respond to the rms value of the input and which is characterized by the manufacturer for use on a specified range of waveforms
[IEV number 313-03-09]FR
transducteur de valeur efficace
transducteur spécifiquement conçu pour répondre à la valeur efficace de l’entrée et qui est caractérisé par le constructeur pour utilisation avec une plage de formes d’onde spécifiée
[IEV number 313-03-09]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > преобразователь среднеквадратичных значений
См. также в других словарях:
input value — įėjimo vertė statusas T sritis Standartizacija ir metrologija apibrėžtis Įėjimo dydžio vertė. atitikmenys: angl. input value vok. Eingangswert, m rus. входное значение, n pranc. valeur d’entrée, f … Penkiakalbis aiškinamasis metrologijos terminų žodynas
Input — is the term denoting either an entrance or changes which are inserted into a system and which activate/modify a process. It is an abstract concept, used in the modeling, system(s) design and system(s) exploitation. It is usually connected with… … Wikipedia
Value added selling — is one of several sales techniques that relies on building on the inherent value of a product or service. By its nature the value add technique is a more flexible and customized selling approach that requires input from a defined range of average … Wikipedia
input tax — value added tax (VAT) charged on supplies made to a taxable person. It can be recovered from HM Revenue & Customs (HMRC) provided that it is attributable to a taxable supply made or to be made and appropriate evidence is held. For further… … Law dictionary
input tax — Value added tax paid by a taxable person on purchasing goods or services from a VAT registered trader. The input tax, excluding irrecoverable input VAT, is set against the output tax in order to establish the amount of VAT to be paid to the tax… … Accounting dictionary
input tax — Value added tax paid by a taxable person on purchasing goods or services from a VAT registered trader. The input tax, excluding irrecoverable input VAT, is set against the output tax in order to establish the amount of VAT to be paid to the tax… … Big dictionary of business and management
input-output coefficient — input output coefficient, a coefficient used in input output tables to measure the value of the purchases by one industry of another industry s products that are needed to produce $1000 worth of sales by the first industry … Useful english dictionary
Value added tax — Taxation An aspect of fiscal policy … Wikipedia
Input-output model — The Input output model of economics uses a matrix representation of a nation s (or a region s) economy to predict the effect of changes in one industry on others and by consumers, government, and foreign suppliers on the economy. This model, if… … Wikipedia
Value Added Tax in Madhya Pradesh — MADHYA PRADESH VALUE ADDED TAX ACTVAT Tax payable on value addition. Value Addition is not profit it is difference between sale prices and purchase price.METHODS OF CHARGING VAT1. Subtraction Method In this method tax is charged on difference of… … Wikipedia
input — ▪ I. input in‧put 1 [ˈɪnpʊt] noun 1. also factor input [countable usually plural, uncountable] ECONOMICS something or someone that is involved or used in a business: • the value of the product as compared with the cost of the inputs … Financial and business terms