-
1 отношение величин сопротивления в системе
- Impedanzverhältnis, n
отношение величин сопротивления в системе
Для заданной точки измерения, обычно на одном конце линии - отношение сопротивления источника к полному сопротивлению защищаемой зоны.
[Разработка типовых структурных схем микропроцессорных устройств РЗА на объектах ОАО "ФКС ЕЭС". Пояснительная записка. Новосибирск 2006 г.]
отношение сопротивлений
Для конкретной точки измерений это отношение сопротивления источника (системы) к сопротивлению цепи КЗ (сопротивление защищаемой зоны).
[Циглер Г. Цифровая дистанционная защита: принципы и применение. М.: Энергоиздат. 2005]EN
system impedance ratio
source impedance ratio (US)
at a given measurement location, commonly at one end of a line, the ratio of the power system source impedance to the impedance of the protected zone
[IEV ref 448-14-14]FR
rapport d'impédance du réseau
en un point de mesure donné, en général à une extrémité d'une ligne, rapport de l'impédance de source du réseau d'énergie à l'impédance de la zone protégée
[IEV ref 448-14-14]Тематики
EN
DE
- Impedanzverhältnis, n
FR
Русско-немецкий словарь нормативно-технической терминологии > отношение величин сопротивления в системе
-
2 коэффициент трансформации ответвления (пары обмоток)
коэффициент трансформации ответвления (пары обмоток)
Коэффициент, равный номинальному коэффициенту трансформации:
- умноженному на коэффициент ответвления обмотки с ответвлениями, если это обмотка высшего напряжения;
- деленному на коэффициент ответвления обмотки с ответвлениями, если это обмотка низшего напряжения.
Примечание — В отличие от номинального коэффициента трансформации, который по определению не может быть меньше 1, коэффициент трансформации ответвления может быть меньше 1 в случаях, когда номинальный коэффициент трансформации близок к 1.
[ ГОСТ 30830-2002]EN
tapping voltage ratio (of a pair of windings)
the ratio which is equal to the rated voltage ratio:
- multiplied by the tapping factor of the tapped winding if this is the high voltage winding
- divided by the tapping factor of the tapped winding if this is the low voltage windin
[IEV number 421-05-08]FR
rapport de transformation de prise (d'une paire d'enroulements)
rapport qui est égal au rapport de transformation assigné:
- multiplié par le facteur de prise de l'enroulement à prises si celui-ci est l'enroulement haute tension
- divisé par le facteur de prise de l'enroulement à prises si celui-ci est l'enroulement basse tension
[IEV number 421-05-08]Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент трансформации ответвления (пары обмоток)
-
3 логометр
логометр
-
[IEV number 312-02-28]EN
ratio-meter
quotient-meter
instrument intended to measure the ratio or the quotient of the values of two quantities
[IEV number 312-02-28]FR
ratiomètre
quotientmètre
appareil destiné à mesurer le rapport ou le quotient des valeurs de deux grandeurs
[IEV number 312-02-28]Тематики
- измерение электр. величин в целом
Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > логометр
-
4 номинальный коэффициент трансформации
номинальный коэффициент трансформации
Отношение номинального напряжения одной обмотки к меньшему или равному номинальному напряжению другой обмотки
(МЭС 421-04-02).
[ ГОСТ 30830-2002]EN
rated voltage ratio (of a transformer)
the ratio of the rated voltage of a winding to the rated voltage of another winding associated with a lower or equal rated voltage
[IEV number 421-04-02]FR
rapport de transformation assigné (d'un transformateur)
rapport de la tension assignée d'un enroulement à celle d'un autre enroulement caractérisé par une tension assignée inférieure ou égale
[IEV number 421-04-02]Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > номинальный коэффициент трансформации
-
5 номинальный коэффициент трансформации трансформатора тока
номинальный коэффициент трансформации трансформатора тока
-EN
rated transformation ratio of a current transformer
the ratio of the rated primary current to the rated secondary current of a current transformer
[IEV number 321-01-19]FR
rapport de transformation assigné d'un transformateur de courant
rapport entre le courant primaire assigné et le courant secondaire assigné d'un transformateur de courant
[IEV number 321-01-19]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > номинальный коэффициент трансформации трансформатора тока
-
6 фактический коэффициент трансформации трансформатора тока
фактический коэффициент трансформации трансформатора тока
-EN
actual transformation ratio of a current transformer
the ratio of the actual primary current to the actual secondary current of a current transformer
[IEV number 321-01-17]FR
rapport de transformation d'un transformateur de courant
rapport entre le courant primaire réel et le courant secondaire réel d'un transformateur de courant
[IEV number 321-01-17]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > фактический коэффициент трансформации трансформатора тока
-
7 добротность
добротность
1. Количественная характеристика потерь колебательной системы при резонансе, равная
где Wк - полный запас энергии колебаний при резонансе;
Wп - потери энергии за период
[ Физический энциклопедический словарь]
2. Количественная мера потерь колебательной системы. Показывает, во сколько раз амплитуда вынужденных колебаний при резонансе превышает амплитуду на частоте, много меньшей резонансной при одинаковой внешней силе
3. Отношение резонансной частоты спектра колебаний к его ширине на уровне 0,707 от максимального значения амплитуды спектра
Примечание
Определения 2 и 3 являются достаточно точными для систем с высокой добротностью (Q >(5-10)), определение 1 пригодно во всех случаях
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
добротность (1)
коэффициент добротности (1)
-
[IEV number 151-15-45]
добротность (2)
коэффициент добротности (2)
-
[IEV number 151-15-46]EN
quality factor (1)
Q factor (1)
for a capacitor or inductor under periodic conditions, ratio of the absolute value of the reactive power to the active power
NOTE 1 – The quality factor is a measure of the losses, usually unwanted, in a capacitor or an inductor.
NOTE 2 – The quality factor depends generally on frequency and voltage.
[IEV number 151-15-45]
quality factor (2)
Q factor (2)
for a resonant circuit at the resonance frequency, 2π times the ratio of the maximum stored energy to the energy dissipated during one period
NOTE – The quality factor is a measure of sharpness of the resonance.
Source: 801-24-12 MOD
[IEV number 151-15-46]FR
facteur de qualité (1), m
facteur de surtension (1), m
pour un condensateur ou une bobine d'inductance en régime périodique, rapport de la valeur absolue de la puissance réactive à la puissance active
NOTE 1 – Le facteur de qualité caractérise les pertes, généralement non désirées, dans un condensateur ou une bobine d'inductance.
NOTE 2 – Le facteur de qualité dépend généralement de la fréquence et de la tension.
[IEV number 151-15-45]
facteur de qualité (2), m
facteur de surtension (2), m
pour un circuit résonant fonctionnant à la fréquence de résonance, 2π fois le rapport de l'énergie maximale emmagasinée dans le circuit à l'énergie dissipée pendant une période
NOTE – Le facteur de qualité caractérise l'acuité de la résonance.
Source: 801-24-12 MOD
[IEV number 151-15-46]Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > добротность
-
8 КПД двигателя
КПД двигателя
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
power-heat relation
The ratio of the work done by an engine to the heat supplied. (Source: UVAROV)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
- ratio chaleur/ énergie fournie
Русско-немецкий словарь нормативно-технической терминологии > КПД двигателя
-
9 коэффициент ответвления
коэффициент ответвления (соответствующий конкретному ответвлению)
Отношение Uотв/Uном (коэффициент ответвления) либо 100 Uотв/Uном ((коэффициент ответвления, выраженный в процентах), где
Uном — номинальное напряжение обмотки, В (см. 3.4.3), a
Uотв — напряжение, возникающее при холостом ходе между выводами обмотки, присоединенной к данному ответвлению, при приложении номинального напряжения к обмотке без ответвлений, В.
Примечание — Это определение не распространяется на последовательную обмотку линейного регулировочного трансформатора (см. 3.1.3), для которого коэффициент ответвления, выраженный в процентах, относится к напряжению обмотки возбуждения или обмотки сетевого трансформатора, связанного с линейным регулировочным трансформатором
(МЭС 421-05-03).
[ ГОСТ 30830-2002]EN
tapping factor
the ratio Ud/ UN (tapping factor) or 100 Ud/ UN (tapping factor expressed as a percentage)
where:
UN is the rated voltage of the winding
Ud is the voltage which would be developed at no-load at the terminals of the winding, connected on the tapping concerned, by applying rated voltage to an untapped winding
NOTE – The tapping factor expresses the relative value of the "effective number of turns" of the tapped winding at the relevant tapping, the basis 1 being the effective number of turns of this winding at the principal tapping
[IEV number 421-05-03]FR
facteur de prise
rapport Ud/ UN (facteur de prise) ou 100 Ud/ UN (facteur de prise exprimé sous la forme d'un pourcentage)
où:
UN est la tension assignée de l'enroulement,
Ud est la tension qui serait développée aux bornes de l'enroulement, connecté sur la prise considérée, en fonctionnement à vide, en appliquant à un enroulement sans prise sa tension assignée
NOTE – Le facteur de prise exprime la valeur relative du "nombre effectif de spires" de l'enroulement à prises pour la prise considérée, la base 1 étant le nombre effectif de spires de cet enroulement pour la prise principale.
[IEV number 421-05-03]Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент ответвления
-
10 небаланс напряжений
небаланс напряжений
Отличие по модулю значения хотя бы одного из фазных или линейных напряжений многофазной системы электроснабжения от значений напряжений других фаз.
[ ГОСТ 23875-88]EN
voltage unbalance
phenomenon due to the differences between voltage deviations on the various phases, at a point of a polyphase system, resulting from differences between the phase currents or geometrical asymmetry in the line
[IEV number 604-01-29]
voltage unbalance (imbalance)
in a polyphase system, a condition in which the magnitudes of the phase voltages or the phase angles between consecutive phases are not all equal (fundamental component)
NOTE In three phase systems, the degree of inequality is usually expressed as the ratio of the negative and zero sequence components to the positive sequence component. In this technical report, voltage unbalance is considered in relation to three-phase systems and negative sequence only
[IEC 61000-3-13, ed. 1.0 (2008-02)]
voltage unbalance
condition in a polyphase system in which the r.m.s. values of the line voltages (fundamental component), and/or the phase angles between consecutive line voltages, are not all equal
NOTE 1 The degree of the inequality is usually expressed as the ratios of the negative- and zero-sequence components to the positive-sequence component.
NOTE 2 In this standard, voltage unbalance is considered in relation to 3-phase systems.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
déséquilibre des tensions d'un réseau
phénomène résultant des différences de charge ou des dissymétries géométriques de lignes et qui provoque des différences entre les écarts de tension sur les diverses phases en un point d'un réseau polyphasé
[IEV number 604-01-29]
déséquilibre de tension
dans un réseau d’énergie électrique polyphasé, état dans lequel les valeurs efficaces des tensions entre conducteurs (composante fondamentale), et/ou les différences de phase entre conducteurs successifs, ne sont pas toutes égales
NOTE 1 Le taux de déséquilibre s’exprime habituellement par le rapport de la composante inverse ou homopolaire à la composante directe.
NOTE 2 Dans la présente norme, le déséquilibre de tension est relatif aux réseaux triphasés
[IEC 61000-4-30, ed. 2.0 (2008-10)]Параллельные тексты EN-RU
Voltage unbalance
Voltage unbalance on the most unbalanced phase, displayed as a percentage of Vavg.
[Schneider Electric]Небаланс напряжений
Самое значительное отличие по модулю значения одного из линейных напряжений, выраженное в процентах от среднего напряжения Vavg.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Смотри также
Русско-немецкий словарь нормативно-технической терминологии > небаланс напряжений
11 коэффициент нулевой последовательности напряжения (тока)
коэффициент нулевой последовательности напряжения (тока)
Величина, равная отношению напряжения (тока) нулевой последовательности к фазному напряжению (току) прямой последовательности в многофазной системе электроснабжения.
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току).
[ ГОСТ 23875-88]EN
unbalance factor
in a three-phase system, the degree of unbalance expressed by the ratio (in per cent) between the r.m.s. values of the negative sequence (or the zero sequence) component and the positive sequence component of voltage or current
[IEV number 604-01-30]FR
taux de déséquilibre
dans un réseau triphasé, expression du degré de déséquilibre par le rapport, exprimé en pourcentage, entre la valeur efficace de chacune des composantes inverse ou homopolaire et celle de la composante directe de la tension ou du courant
[IEV number 604-01-30]Тематики
EN
DE
FR
Смотри также
43. Коэффициент нулевой последовательности напряжения (тока)
D. Unsymmetriegrad
E. Unbalance factor
F. Taux de déséquilibre
Величина, равная отношению напряжения (тока) нулевой последовательности к фазному напряжению (току) прямой последовательности в многофазной системе электроснабжения.
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току)
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > коэффициент нулевой последовательности напряжения (тока)
12 коэффициент обратной последовательности напряжения (тока)
коэффициент обратной последовательности напряжения (тока)
Величина, равная отношению напряжения (тока) обратной последовательности к напряжению (току) прямой последовательности в многофазной системе электроснабжения.
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току).
[ ГОСТ 23875-88]EN
unbalance factor
in a three-phase system, the degree of unbalance expressed by the ratio (in per cent) between the r.m.s. values of the negative sequence (or the zero sequence) component and the positive sequence component of voltage or current
[IEV number 604-01-30]FR
taux de déséquilibre
dans un réseau triphasé, expression du degré de déséquilibre par le rapport, exprimé en pourcentage, entre la valeur efficace de chacune des composantes inverse ou homopolaire et celle de la composante directe de la tension ou du courant
[IEV number 604-01-30]Тематики
EN
DE
FR
Смотри также
42. Коэффициент обратной последовательности напряжения (тока)
D. Unsymmetriegrad
E. Unbalance factor
F. Taux de déséquilibre
Величина, равная отношению напряжения (тока) обратной последовательности к напряжению (току) прямой последовательности в многофазной системе электроснабжения.
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току)
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > коэффициент обратной последовательности напряжения (тока)
13 коэффициент пульсации напряжения (тока) no среднему значению
коэффициент пульсации напряжения (тока) no среднему значению
Величина, равная отношению среднего значения переменной составляющей пульсирующего напряжения (тока) к его постоянной составляющей.
[ ГОСТ 23875-88]EN
r.m.s.-ripple factor
the ratio of the r.m.s. value of the ripple content to the absolute value of the direct component of a pulsating quantity
Source: MOD 131-03-13
[IEV number 161-02-27]FR
taux d'ondulation efficace
rapport de la valeur efficace de l'ondulation d'une grandeur pulsatoire à la valeur absolue de la composante continue
Source: MOD 131-03-13
[IEV number 161-02-27]Тематики
EN
- r.m.s.-ripple factor
DE
FR
- taux d’ondulation efficace (d’une tension ou d’un courant pulsatoire)
Смотри также
Русско-немецкий словарь нормативно-технической терминологии > коэффициент пульсации напряжения (тока) no среднему значению
14 дизельный двигатель
дизельный двигатель
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
diesel engine
An internal combustion engine operating on a thermodynamic cycle in which the ratio of compression of the air charge is sufficiently high to ignite the fuel subsequently injected into the combustion chamber. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > дизельный двигатель
15 коэффициент циклической продолжительности включения
коэффициент циклической продолжительности включения
-
ГОСТ Р 52776-2007( МЭК 60034-1-2004)EN
cyclic duration factor
the ratio between the period of loading, including starting and electric braking, and the duration of the duty cycle, expressed as a percentage
[IEV number 411-51-09]FR
facteur de marche
rapport de la période de fonctionnement en charge, y compris le démarrage et le freinage électrique, à la durée du cycle de service, exprimé en pourcentage
[IEV number 411-51-09]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент циклической продолжительности включения
16 измеритель коэффициента мощности
измеритель коэффициента мощности
-
[IEV number 313-01-14]EN
power factor meter
instrument intended to measure the ratio of the active to the apparent power in an electrical circuit
[IEV number 313-01-14]FR
appareil de mesure de facteur de puissance
appareil destiné à mesurer le rapport de la puissance active à la puissance apparente dans un circuit électrique
[IEV number 313-01-14]Тематики
- измерение электр. величин в целом
EN
DE
Русско-немецкий словарь нормативно-технической терминологии > измеритель коэффициента мощности
17 коэффициент искажения синусоидальности кривой напряжения (тока)
коэффициент искажения синусоидальности кривой напряжения (тока)
Величина, равная отношению действующего значения суммы гармонических составляющих к действующему значению основной составляющей переменного напряжения (тока).
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току).
[ ГОСТ 23875-88]
коэффициент нелинейных искажений
коэффициент несинусоидальности
КНИ
Определяет веса высших гармоник переменного напряжения по отношению к основной гармонике. Чем КНИ меньше, тем ближе форма напряжения к чистой синусоиде. Например: синусоидальная форма сигнала (КНИ=0), форма сигнала отлична от синусоидальной, но искажения не заметны на глаз (КНИ<3%), отклонение формы сигнала от синусоидальной заметно на глаз (КНИ>5%), сигнал имеет трапецеидальную или ступенчатую форму (КНИ<21%), сигнал имеет прямоугольную форму (КНИ=43%)
[ http://www.radistr.ru/misc/document423.phtml]
(полный) коэффициент гармоник
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва]EN
total harmonic distortions
THD
RMS value of all harmonics in a waveform (excluding fundamental) divided by RMS value of fundamental. THDV refers to Voltage waveform. THDI refers to Current waveform.
[ http://www.upsonnet.com/UPS-Glossary/]total 3rd order harmonic distortion
коэффициент искажения синусоидальности, вызванный гармоническими составляющими третьего порядка
total harmonic distortion; THD
коэффициент искажения синусоидальности
общий коэффициент несинусоидальностиtotal harmonic current distortion; THDI
коэффициент искажения синусоидальности кривой тока
обшее гармоническое искажение токаtotal harmonic voltage distortion; THDV, THDU
коэффициент искажения синусоидальности кривой напряжения
обшее гармоническое искажение напряженияПараллельные тексты EN-RU
THD is the ratio of harmonic content to the fundamental and provides a general indication of the quality of a waveform.
[Schneider Electric]Коэффициент искажения синусоидальности (THD) представляет собой отношение суммы гармонических составляющих к значению основной составляющей и является основным индикатором качества формы электрического сигнала.
[Перевод Интент]
Тематики
Синонимы
- КНИ
- коэффициент гармоник
- коэффициент искажения
- коэффициент нелинейных искажений
- коэффициент несинусоидальности
- полный коэффициент гармоник
EN
- distortion factor (of a non-sinusoidal alternating voltage or current)
- THD
- total harmonic distortions
DE
FR
- facteur de distortion (d’une tension ou d’un courant alternatif non sinusoïdal)
Смотри также
55. Коэффициент искажения синусоидальности кривой напряжения (тока)
Коэффициент искажения
D. Klirrfaktor
E. Distortion factor (of a non-sinusoidal alternating voltage or current)
F. Facteur de distortion (d’une tension ou d’un courant alternative non sinusoïdal)
Величина, равная отношению действующего значения суммы гармонических составляющих к действующему значению основной составляющей переменного напряжения (тока).
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току)
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > коэффициент искажения синусоидальности кривой напряжения (тока)
18 уровень эффективности
уровень эффективности
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
efficiency level
The ratio of output to input, usually given as a percentage. (Source: ECHO2)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > уровень эффективности
19 коэффициент подавления общего вида
коэффициент подавления общего вида
-
[IEV number 312-06-21]EN
common mode rejection ratio
CMRR (abbreviation)
ratio of the voltage applied between a specified reference point and the input terminals, when connected together by a specified circuit, to the voltage required between the input terminals to produce the same value of the output
NOTE 1 – The common mode rejection ratio is usually expressed in decibels and can depend on the frequency, the waveform and the method of measurement.
NOTE 2 – Common mode rejection ratio can also apply to quantities other than voltage.
[IEV number 312-06-21]FR
rapport de réjection de mode commun
rapport de la tension appliquée entre un point de référence spécifié et les deux bornes d'entrée connectées l'une à l'autre par un circuit spécifié, à la tension nécessaire entre les bornes d'entrée pour produire la même valeur de sortie
NOTE 1 – Le facteur de réjection de mode commun est généralement exprimé en décibels et peut dépendre de la fréquence, de la forme d’onde et de la méthode de mesure.
NOTE 2 – Le rapport de réjection de mode commun peut aussi s'appliquer à des grandeurs autres que les tensions.
[IEV number 312-06-21]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент подавления общего вида
20 коэффициент подавления при последовательном включении
коэффициент подавления при последовательном включении
-
[IEV number 312-06-22]EN
series mode rejection ratio
SMRR (abbreviation)
ratio of the series mode voltage causing a specified change in output information, to the voltage initiated by the measurand which would produce the same change
NOTE 1 – The series mode rejection ratio is usually expressed in decibels and may depend on the frequency, the waveform and the method of measurement.
NOTE 2 – Series mode rejection ratio can also apply to quantities other than voltage.
[IEV number 312-06-22]FR
rapport de réjection de mode série
rapport de la tension de mode série, provoquant un changement spécifié d'information de sortie, à la tension résultant du mesurande qui produirait le même changement
NOTE 1 – Le facteur de réjection de mode série est généralement exprimé en décibels et peut dépendre de la fréquence, de la forme d’onde et de la méthode de mesure.
NOTE 2 – Le rapport de réjection de mode commun peut aussi s'appliquer à des grandeurs autres que les tensions.
[IEV number 312-06-22]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент подавления при последовательном включении
СтраницыСм. также в других словарях:
ratio — the proportional relationship of one thing to another * * * ratio ra‧ti‧o [ˈreɪʆiəʊ ǁ ˈreɪʆoʊ] noun [countable] a relationship between two amounts that is represented by a pair of numbers showing how much greater one amount is than the other: •… … Financial and business terms
Ratio Studiorum — • The educational system of the Jesuits Catholic Encyclopedia. Kevin Knight. 2006. Ratio Studiorum Ratio Studiorum † … Catholic encyclopedia
Ratio decidendi — (plural: rationes decidendi) is a Latin phrase meaning the reason (or ratio nale) for the decision. The ratio decidendi is:: [t] he point in a case which determines the judgment [See Black s Law Dictionary, page 1135 (5th ed. 1979).] or: the… … Wikipedia
Ratio — Ra ti*o (r[=a] sh[i^]*[ o] or r[=a] sh[ o]), n. [L., fr. reri, ratus, to reckon, believe, think, judge. See {Reason}.] 1. (Math.) The relation which one quantity or magnitude has to another of the same kind. It is expressed by the quotient of the … The Collaborative International Dictionary of English
Ratio of a geometrical progression — Ratio Ra ti*o (r[=a] sh[i^]*[ o] or r[=a] sh[ o]), n. [L., fr. reri, ratus, to reckon, believe, think, judge. See {Reason}.] 1. (Math.) The relation which one quantity or magnitude has to another of the same kind. It is expressed by the quotient… … The Collaborative International Dictionary of English
Ratio Studiorum — The Ratio Studiorum (Latin: Plan of Studies ) often designates the document that formally established the globally influential system of Jesuit education in 1599. Its full title is Ratio atque Institutio Studiorum Societatis Iesu ( The Official… … Wikipedia
ratio decidendi — ra·tio de·ci·den·di / rā shē ˌō ˌde sə den ˌdī, rā ˌshō , ˌdā sē den dē/ n [Latin, grounds for deciding]: the principle or rule constituting the basis of a court decision Merriam Webster’s Dictionary of Law. Merriam Webster. 1996. ratio deciden … Law dictionary
Ratio spread — The ratio spread is a strategy in options trading that involves buying some number of options and selling a larger number of other options of the same underlying market and (usually) the same expiration date, but of a different strike price.… … Wikipedia
Ratio Club — The Ratio Club was a small informal dining club of young psychologists, physiologists, mathematicians and engineers who met to discuss issues in cybernetics. The idea of the club arose from a symposium on animal behaviour held by the Society of… … Wikipedia
The theory of a second-best solution — concerns the events that happen when a condition for an optimal outcome isn t met. In that case a second best solution should be sought. But the second best solution isn t always the one where every other condition is met except the one missing… … Wikipedia
Ratio estimate — The ratio of two population aggregates (totals). For example, average miles traveled per vehicle is the ratio of total miles driven by all vehicles, over the total number of vehicles, within any subgroup. There are two types of ratio estimates… … Energy terms
Перевод: с русского на немецкий
с немецкого на русский- С немецкого на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский