-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
immediate — 01. George s new restaurant has been an [immediate] success, with almost a full house every night since it opened. 02. Phone us [immediately] if you have any problems. 03. The medicine had an [immediate] and positive effect. 04. A car bomb threat … Grammatical examples in English
immediate — im|me|di|ate W2S2 [ıˈmi:diət] adj [Date: 1300 1400; : Late Latin; Origin: immediatus, from mediatus in between, separated ] 1.) happening or done at once and without delay ▪ Our immediate response to the attack was sheer horror. ▪ They promise… … Dictionary of contemporary English
immediate — adjective 1 NO DELAY happening or done at once and without delay: The police response to the situation was forceful and immediate. | seek immediate medical attention 2 NOW (only before noun) existing now, and needing to be dealt with quickly: Our … Longman dictionary of contemporary English
Area code 916 — North American area code 916 is a state of California telephone area code which was one of the first three original area codes established in California in October, 1947. It covered the far north portion of the state. It was split in a flash cut… … Wikipedia
Immediate Action Rapid Deployment — (IARD) is a term used to describe a police tactic that provides swift deployment of law enforcement resources to developing or on going, life threatening situations where delayed deployment of emergency personnel could otherwise result in death… … Wikipedia
Area code 816 — is an area code in the state of Missouri that covers the Kansas City Metropolitan Area and the city of St. Joseph to the north. The area code used to cover most of northwestern Missouri to the state s borders with Iowa, Kansas and Nebraska, but… … Wikipedia
area — ar‧e‧a [ˈeəriə ǁ ˈeriə] noun [countable] 1. a part of a city or country: • What area of Bristol do you live in? • the New York metropolitan area (= New York city and the area around it ) asˌsisted ˈarea … Financial and business terms
Area code 404 — covers Atlanta and its immediate neighbors, roughly within Interstate 285.Originally, it covered all of Georgia when the area code system was first created in the 1940s and implemented in 1951. On July 1, 1954, area code 912 was assigned to… … Wikipedia
Area code 614 — Area code 614, which had covered the entire southeastern quarter of the state of Ohio for decades, now represents only the Columbus metropolitan area; it is one of the original area codes established in 1947. In 1998, most of the old 614… … Wikipedia
area placentalis — area pla·cen·ta·lis .plas ən tā ləs n the part of the trophoblast in early placental vertebrate embryos that lies in immediate contact with the uterine mucosa … Medical dictionary
Area bombardment — Aerial area bombardment is the policy of indiscriminate bombing of an enemy s cities, for the purpose of destroying the enemy s means of producing military materiel, communications, government centres and civilian morale. It differs from the use… … Wikipedia
