-
1 прямизна скважины
Русско-английский словарь по нефти и газу > прямизна скважины
-
2 прямизна скважины
Русско-английский словарь нормативно-технической терминологии > прямизна скважины
-
3 прямизна скважины
Oil: hole straightness -
4 выдерживаться с точностью до
•Roundness and straightness of the hole is held to within 0.0003 inch.
Русско-английский научно-технический словарь переводчика > выдерживаться с точностью до
-
5 выдерживаться с точностью до
•Roundness and straightness of the hole is held to within 0.0003 inch.
Русско-английский научно-технический словарь переводчика > выдерживаться с точностью до
-
6 отклонение
Допускаемое отклонение размеров обработанных поверхностей 0,013 мм — Allowable size deviation of finished surfaces 0.013 mmДопускаемое отклонение — Tolerance; allowable deviation, allowable errorДопускается отклонение... — Allowable error...Отклонение величины угла по отношению к поверхности А не более 0,003 мм — Angular tolerance relative to surface A 0.003 mmОтклонение от перпендикулярности поверхностей В и Г не более 0,003 мм — Perpendicular misalignment of surfaces C and D is within 0.003 mm; surfaces C and D are square within 0.003 mmОтклонение от прямолинейности (образующих) не более 0,01 мм — Straightness tolerance [tol.] 0.01 mm; straight within 0.01 mmОтклонение от симметрично го расположения паза относительно АВ не более 0,003 мм — Slot symmetry tolerance 0.003 mm relative to AB; symmetric with AB within 0.003 mmОтклонение от соосности относительно поверхности А не более 0,02 мм — Parallel misalignment with surface A within 0.02 mmОтклонение от соосности по верхностей диаметра D не более 0,02 мм — Diameters D are concentric within 0.02 mmОтклонение от соосности поверхностей А, В, С не более 0,02 мм — Surfaces A, B, C concentric within 0.02 mm; misalignment of surfaces A, B, C is not in excess of 0.02 mmОтклонение от соосности поверхностей М и Н не более 0.02 мм — Eccentricity of surfaces M and N is not to exceed 0.02 mmОтклонение от соосности поверхностей относительно отверстия диам. 20 мм не более указанного — Surface misalignment with hole 20 dia should not exceed the specified limitsОтклонение поверхности от плоскостности не более 0,02 мм — Flatness tol. 0.02 mm; surface flatness error within 0.02 mmПоставки машин и оборудования. Русско-английский словарь > отклонение
См. также в других словарях:
прямизна скважины — — [http://slovarionline.ru/anglo russkiy slovar neftegazovoy promyishlennosti/] Тематики нефтегазовая промышленность EN hole straightness … Справочник технического переводчика
Drilling — For other uses, see Drilling (disambiguation). Drilling is a cutting process that uses a drill bit to cut or enlarge a hole in solid materials. The drill bit is a multipoint, end cutting tool. It cuts by applying pressure and rotation to the… … Wikipedia
Trojan Oaks Golf Course — Infobox Golf Facility golf facility name = Trojan Oaks Golf Course location = Troy, AL Alabama United States establishment = 1977 type = Public owner = Troy University manager = Jack Phillips holes = 9 tournaments = None website =… … Wikipedia
Geometric dimensioning and tolerancing — (GD T) is a system for defining and communicating engineering tolerances. It uses a symbolic language on engineering drawings and computer generated three dimensional solid models for explicitly describing nominal geometry and its allowable… … Wikipedia
arts, East Asian — Introduction music and visual and performing arts of China, Korea, and Japan. The literatures of these countries are covered in the articles Chinese literature, Korean literature, and Japanese literature. Some studies of East Asia… … Universalium
Lateral movement — Lateral movements are movements made on a horse that are used for training purposes, that involve the horse moving in a direction other than straight forward. They vary in difficulty, and should be used in a progressive manner, according to the… … Wikipedia
Fernald Feed Materials Production Center — The Fernald Feed Materials Production Center (commonly referred to simply as Fernald) was a uranium processing facility located near the rural town of Fernald, in Hamilton County, Ohio, about 20 miles northwest of Cincinnati, which fabricated… … Wikipedia
Katana construction — was the labour intensive bladesmithing process developed in Japan for forging katana and other Japanese blades. Katana and wakizashi were often forged with different profiles, different blade thicknesses, and varying amounts of grind. Wakizashi… … Wikipedia
NMR tube — An NMR tube filled with a colorless sample, sealed with a green polyethylene cap and Parafilm An NMR tube is a thin glass walled tube used to contain samples in nuclear magnetic resonance spectroscopy. Typically NMR tubes come in 5 mm… … Wikipedia
Steel Casing Pipe — Unreferenced|date=March 2007Steel Casing Pipe which is also know as encasement pipe is most commonly used in underground construction to protect utility lines of various types from getting damaged.Such damage might occur due to the elements of… … Wikipedia
North American hunting technologies — Contents 1 Paleo Indians 1.1 Paleo Indian weapons technologies 1.2 Hunting 1.3 Clovis first 1.4 … Wikipedia