-
21 full voltage starter application
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > full voltage starter application
-
22 augstsprieguma tīkls
▪ Terminilv ekon.ru сеть высокого напряженияLZAlvi▪ EuroTermBank terminiUzņ, Ek, Dokru ceть выcoкoгo нaпpяжeнияETB -
23 transformer
3) пищ. котёл для получения инвертированного сиропа•-
adapter transformer
-
adjustable transformer
-
air transformer
-
air-blast transformer
-
air-cooled transformer
-
air-core transformer
-
air-natural transformer
-
amorphous-core transformer
- arc furnace transformer -
arc-welding transformer
-
audio-frequency transformer
-
autocompounded current transformer
-
autocompounded voltage transformer
-
autoconnected transformer
-
auxiliary transformer
-
balanced-to-unbalanced transformer
-
balance-to-unbalanced transformer
-
balanced-to-unbalance transformer
-
balance-to-unbalance transformer
-
balanced transformer
-
balancing transformer
-
ballast transformer
-
banked distribution transformers
-
bar-type transformer
-
bell transformer
-
booster transformer
-
bridge transformer
-
busbar current transformer
-
capacitive voltage transformer
-
cascade transformer
-
cast resin transformer
-
center-tapped transformer
-
closed core transformer
-
code transformer
-
combined voltage and current transformer
-
compensated current transformer
-
compensated voltage transformer
-
compound-filled instrument transformer
-
constant-current transformer
-
constant-potential transformer
-
control circuit transformer
-
control transformer
-
converter transformer
-
coreless transformer
-
core-type transformer
-
coupling transformer
-
current transformer
-
decoupling transformer
-
differential transformer
-
diode-split line-output transformer
-
direct-current transformer
-
distribution transformer
-
double-stub transformer
-
double-tuned transformer
-
double-winding transformer
-
driving transformer
-
dry-type transformer
-
dry transformer
-
dry-type forced-air-cooled transformer
-
dry-type self-cooled transformer
-
E transformer
-
earthed transformer
-
earthing transformer
-
effective grounded transformer
-
EHV power transformer
-
excitation transformer
-
extra-high-voltage power transformer
-
feed transformer
-
feeder transformer
-
feeding transformer
-
filter transformer
-
five-legged transformer
-
flash transformer
-
flyback transformer
-
forced-air-cooled transformer
-
forced-oil transformer
-
frame-output transformer
-
furnace transformer
-
gas-filled transformer
-
gas-insulated transformer
-
general transformer
-
general-purpose transformer
-
grounded transformer
-
grounding transformer
-
high-potential transformer
-
high-power transformer
-
high-voltage transformer
-
horizontal-output transformer
-
house transformer
-
hydropneumatic transformer
-
ideal transformer
-
image-output transformer
-
impedance transformer
-
impedance-matching transformer
-
impulse current transformer
-
indoor transformer
-
induction voltage transformer
-
injector transformer
-
input transformer
-
instrument transformer
-
insulated-core transformer
-
insulating transformer
-
integral current transformer
-
interphase transformer
-
intervening current transformer
-
iron-clad transformer
-
iron-core transformer
-
isolating transformer
-
lightning-proof transformer
-
line regulating transformer
-
line transformer
-
linear hydraulic transformer
-
line-output transformer
-
liquid-filled transformer
-
loading transformer
-
low-power transformer
-
low-voltage transformer
-
mains transformer
-
manhole transformer
-
matching transformer
-
measuring transformer
-
micromodular transformer
-
mode transformer
-
molded transformer
-
multiratio current transformer
-
multiratio voltage transformer
-
multiwinding transformer
-
natural-draft transformer
-
network transformer
-
nonmagnetic current transformer
-
nonresonating transformer
-
oil-cooled transformer
-
oil transformer
-
oil-filled instrument transformer
-
oil-immersed forced-air-cooled transformer
-
oil-immersed forced-oil-cooled transformer
-
oil-immersed self-cooled transformer
-
oil-immersed transformer
-
oil-immersed water-cooled transformer
-
one-coil transformer
-
one-to-one transformer
-
on-load tap-changing transformer
-
open-core transformer
-
outdoor transformer
-
output transformer
-
pad-mounted transformer
-
peaking transformer
-
peak transformer
-
phase-shifting transformer
-
pole-type transformer
-
polyphase transformer
-
potential transformer
-
power transformer
-
protection current transformer
-
protection voltage transformer
-
protective transformer
-
pulse transformer
-
pulse-forming transformer
-
radio-frequency transformer
-
reactance-earthed transformer
-
reactor transformer
-
rectifier transformer
-
reducing transformer
-
regulating transformer
-
relay transformer
-
resistance-earthed transformer
-
resonance transformer
-
rotary hydraulic transformer
-
rotary transformer
-
rotatabletransformer
-
saturable current transformer
-
saturable transformer
-
saturating current transformer
-
sealed transformer
-
self-cooled transformer
-
self-protected transformer
-
series regulating transformer
-
series transformer
-
SF6-filled transformer
-
shell-core transformer
-
shell-form
-
shell-type transformer
-
shunt transformer
-
signal transformer
-
single-phase transformer
-
single-turn current transformer
-
small-power transformer
-
solidly earthed transformer
-
spare transformer
-
standard current transformer
-
standard instrument transformer
-
standard potential transformer
-
standby transformer
-
starting transformer
-
step-down transformer
-
step-up transformer
-
subdivided transformer
-
submersible transformer
-
substation transformer
-
supply transformer
-
tank transformer
-
tap-changing transformer
-
tap-changing-under-load transformer
-
tapped transformer
-
teaser transformer
-
testing transformer
-
test transformer
-
thermal transformer
-
three-circuit transformer
-
three-legged transformer
-
three-leg transformer
-
three-phase transformer
-
three-winding transformer
-
through-type current transformer
-
tool transformer
-
toroidal-coretransformer
-
toroidaltransformer
-
track-circuit transformer
-
track transformer
-
traction-feeding transformer
-
triple-wound transformer
-
tuned transformer
-
two-winding transformer
-
unbalanced-to-balanced transformer
-
unbalance-to-balanced transformer
-
unbalanced-to-balance transformer
-
unbalance-to-balance transformer
-
unearthed transformer
-
variable-ratio transformer
-
vertical-output transformer
-
voltage measuring transformer
-
voltage transformer
-
water-cooled transformer
-
welding transformer
-
window-type current transformer
-
zero-phase sequence current transformer -
24 distribution
- распределительное устройство
- распределительная сеть
- распределение характеристики
- распределение (в биотехнологии)
- внедрение (в практику)
внедрение
1. Процесс планомерного перевода объекта (предприятия или организации, системы управления, отдельного процесса или его элемента) из существующего состояния в новое, предусмотренное проектом.
2. Распространение нововведений, достижение практического использования прогрессивных идей, изобретений, результатов научных исследований.
[ http://www.lexikon.ru/dict/buh/index.html]Тематики
EN
распределительная сеть
Часть энергетической системы, которая предназначена для распределения электроэнергии и работает, как правило, на напряжении до 110 кВ.
[ ГОСТ Р 54325-2011 (IEC/TS 61850-2:2003)]Тематики
EN
распределительное устройство
Распределительным устройством (РУ) называется электроустановка, служащая для приема и распределения электроэнергии и содержащая сборные и соединительные шины, коммутационные аппараты, вспомогательные устройства (компрессорные, аккумуляторные и др.), а также устройства защиты, автоматики и измерительные приборы.
[РД 34.20.185-94]
распределительное устройство
Электроустановка, предназначенная для приема и распределения электрической энергии на одном напряжении и содержащая коммутационные аппараты и соединяющие их сборные шины [секции шин], устройства управления и защиты.
Примечание. К устройствам управления относятся аппараты и связывающие их элементы обеспечивающие контроль, измерение, сигнализацию и выполнение команд.
[ ГОСТ 24291-90]
[ ГОСТ Р 53685-2009]
электрическое распределительное устройство
распределительное устройство
Устройство, предназначенное для приема и распределения электроэнергии на одном напряжении и содержащее коммутационные аппараты и соединяющие их сборные соединительные устройства.
Примечание. В состав распределительного устройства дополнительно могут входить устройства защиты и управления
[ОСТ 45.55-99]
распределительное устройство
Электроустановка, служащая для приема и распределения электроэнергии и содержащая коммутационные аппараты, сборные и соединительные шины, вспомогательные устройства (компрессорные, аккумуляторные и др.), а также устройства защиты, автоматики и измерительные приборы.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]
устройство распределительное
Совокупность аппаратов и приборов для приёма и распределения электроэнергии одного напряжения, вырабатываемой электростанцией или преобразуемой подстанцией
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
switching substation
a substation which includes switchgear and usually busbars, but no power transformers
[IEV number 605-01-02]FR
poste de sectionnement
poste de coupure
poste comprenant des organes de manoeuvre et généralement des jeux de barres, à l'exclusion de transformateurs de puissance
[IEV number 605-01-02]В качестве РУ 6—10 кВ используется сборка высокого напряжения с однополюсными разъединителями и вертикальным расположением фаз одного присоединения и одна камера КСО с выключателем нагрузки и предохранителями для подключения трансформатора. Для РУ 0,4 кВ применяются сборки низкого напряжения с предохранителями и вертикальным расположением фаз одного присоединения.
На ПС применяются открытые (ОРУ), закрытые (ЗРУ) или комплектные (КРУ) распределительные устройства.
[ http://energy-ua.com/elektricheskie-p/klassifikatsiya.html]
В общем случае ПС и РУ являются составной частью электроустановок, которые различаются:
-
по назначению:
- генерирующие,
- преобразовательно-распределительные,
-
потребительские.
Генерирующие электроустановки служат для выработки электроэнергии, преобразовательно-распределительные электроустановки преобразуют электроэнергию в удобный для передачи и потребления вид, передают ее и распределяют между потребителями;
-
по роду тока:
- постоянного тока,
- переменного тока.
-
по напряжению:
- до 1000 В,
- выше 1000 В.
ГОСТ 29322—92 установлена следующая шкала номинальных напряжений:
Шкала номинальных напряжений ограничена сравнительно небольшим числом стандартных значений, благодаря чему изготавливается небольшое число типоразмеров машин и оборудования, а электросети выполняются более экономичными. В установках трехфазного тока номинальным напряжением принято считать напряжение между фазами (междуфазовое напряжение). Согласнодля электросетей переменного тока частотой 50 Гц междуфазовое напряжение должно быть: 12, 24, 36, 42, 127, 220, 380 В; 3, 6, 10, 20, 35, 110, 150, 220, 330, 500, 750 и 1150 кВ;
для электросетей постоянного тока: 12, 24, 36, 48, 60, 110, 220, 440, 660, 825, 3000 В и выше.-
по способу присоединения к электросети ПС разделяются на:
- тупиковые (блочные),
- ответвительные (блочные),
- проходные (транзитные)
- узловые.
Тупиковые ПС получают питание по одной или двум тупиковым ВЛ.
Ответвительные ПС присоединяются ответвлением к одной или двум проходящим ВЛ с односторонним или двухсторонним питанием.
Проходные ПС включаются в рассечку одной или двух проходящих ВЛ с односторонним или двухсторонним питанием.
Узловые ПС кроме питающих имеют отходящие радиальные или транзитные ВЛ.-
по способу управления ПС могут быть:
- только с телесигнализацией,
- телеуправляемыми с телесигнализацией,
- с телесигнализацией и управлением с общеподстанционного пункта управления (ОПУ).
Подстанции оперативно обслуживаются постоянным дежурным персоналом на щите управления, дежурными на дому или оперативно-выездными бригадами (ОВБ). Ремонт ПС осуществляется специализированными выездными бригадами централизованного ремонта или местным персоналом подстанции.
В РУ напряжением до 1000 В провода, шины, аппараты, приборы и конструкции выбирают как по нормальным условиям работы (напряжению и току), так и по термическим и динамическим воздействиям токов коротких замыканий (КЗ) или предельно допустимой отключаемой мощности.
В РУ и ПС напряжением выше 1000 В расстояния между электрооборудованием, аппаратами, токоведущими частями, изоляторами, ограждениями и конструкциями устанавливаются так, чтобы при нормальном режиме работы электроустановки возникающие физические явления (температура нагрева, электрическая дуга, выброс газов, искрение и др.) не могли привести к повреждению оборудования и КЗ.[ http://energy-ua.com/elektricheskie-p/klassifikatsiya.html]
Several different classifications of switchgear can be made:- By the current rating.
-
By interrupting rating (maximum short circuit current that the device can safely interrupt)
- Circuit breakers can open and close on fault currents
- Load-break/Load-make switches can switch normal system load currents
- Isolators may only be operated while the circuit is dead, or the load current is very small.
-
By voltage class:
- Low voltage (less than 1,000 volts AC)
- Medium voltage (1,000–35,000 volts AC)
- High voltage (more than 35,000 volts AC)
-
By insulating medium:
-
By construction type:
- Indoor (further classified by IP (Ingress Protection) class or NEMA enclosure type)
- Outdoor
- Industrial
- Utility
- Marine
- Draw-out elements (removable without many tools)
- Fixed elements (bolted fasteners)
- Live-front
- Dead-front
- Open
- Metal-enclosed
- Metal-clad
- Metal enclosed & Metal clad
- Arc-resistant
-
By IEC degree of internal separation
- No Separation (Form 1)
- Busbars separated from functional units (Form 2a, 2b, 3a, 3b, 4a, 4b)
- Terminals for external conductors separated from busbars (Form 2b, 3b, 4a, 4b)
- Terminals for external conductors separated from functional units but not from each other (Form 3a, 3b)
- Functional units separated from each other (Form 3a, 3b, 4a, 4b)
- Terminals for external conductors separated from each other (Form 4a, 4b)
- Terminals for external conductors separate from their associated functional unit (Form 4b)
-
By interrupting device:
-
By operating method:
- Manually operated
- Motor/stored energy operated
- Solenoid operated
-
By type of current:
-
By application:
-
By purpose
- Isolating switches (disconnectors)
- Load-break switches.
- Grounding (earthing) switches
A single line-up may incorporate several different types of devices, for example, air-insulated bus, vacuum circuit breakers, and manually operated switches may all exist in the same row of cubicles.
Ratings, design, specifications and details of switchgear are set by a multitude of standards. In North America mostly IEEE and ANSI standards are used, much of the rest of the world uses IEC standards, sometimes with local national derivatives or variations.
[Robert W. Smeaton (ed) Switchgear and Control Handbook 3rd Ed., Mc Graw Hill, new York 1997]
[ http://en.wikipedia.org/wiki/High_voltage_switchgear]Тематики
- электрификация, электроснабж. железных дорог
- электроагрегаты генераторные
- электробезопасность
- электроснабжение в целом
Синонимы
EN
- distribution
- energy distribution board
- gear
- switch-gear
- switchboard
- switchgear
- switching substation
- switchyard
DE
FR
3.1.2.1 распределение характеристики (distribution): Распределение вероятностей наблюдаемой характеристики, описывающее ее вероятностное поведение.
Примечание 1 - Распределение вероятностей наблюдаемой характеристики может быть представлено, например, в виде ранжированных результатов наблюдений или гистограммы, построенной по результатам наблюдений. Распределение вероятностей позволяет описать все свойства наблюдаемой характеристики за исключением последовательности, в которой получены данные.
Примечание 2 - Распределение характеристики зависит от преобладающих условий получения данных. Таким образом, для получения достоверной информации о распределении характеристики необходимо установить условия получения данных.
Примечание 3 - Важно знать вид распределения (нормальное, лог-нормальное и т.п.) до прогнозирования или оценки показателя воспроизводимости процесса, показателей его функционирования (пригодности), индексов или доли несоответствующих единиц продукции.
[3534-2:2006, пункт 2.5.1]
Источник: ГОСТ Р ИСО 21747-2010: Статистические методы. Статистики пригодности и воспроизводимости процесса для количественных характеристик качества оригинал документа
Англо-русский словарь нормативно-технической терминологии > distribution
-
25 terminal
1) конечная позиция ( при перемещении), конечная точка2) терминал, конечное устройство, оконечное устройство || терминальный3) конечное слово; конечный слог4) зажим, клемма; ввод; вывод•- blank terminal
- BTR terminal
- CAD terminal
- cathode terminal
- component's terminals
- CRT terminal
- CRT-based terminal
- current terminal
- data terminal
- data-entry terminal
- design terminal
- desk-top terminal
- dumb terminal
- dump terminal
- EDP terminal
- ESD terminal
- external input terminal
- forward terminal
- gate terminal
- hand-held terminal
- hardcopy terminal
- high-voltage terminal
- induction terminal
- intelligent terminal
- interactive terminal
- intermediate voltage terminal
- keyboard terminal
- local intelligent terminal
- low-voltage terminal
- machine interface terminal
- main terminal
- master terminal
- negative current terminal
- network terminal
- networked DNC terminal
- networked terminal
- nonusable terminal
- output terminal
- portable hand-held terminal
- positive current terminal
- radio data terminal
- remote dispatch terminal
- remote terminal
- room terminal
- shopfloor terminal
- supervisory terminal
- terminal of belt conveyor
- transfer terminal
- video display terminal
- video terminal
- work-station factory terminalEnglish-Russian dictionary of mechanical engineering and automation > terminal
-
26 distribution companies
распределенное производство электроэнергии
Распределенное производство электроэнергии включает в себя небольшие электростанции, расположенные в распределительной сети электроэнергетического предприятия с целью покрытия местной или региональной пиковой нагрузки (на уровне подстанции) или для того, чтобы отказаться от модернизации или строительства дополнительных местных распределительных линий.
[Англо-русский глосcарий энергетических терминов ERRA]EN
distribution companies
Electricity companies responsible for the psysical transportation of electricity from the high-voltage transmission network to the middle- and low-voltage customers distributed generation: a distributed generation system involves small amounts of generation located on a utility's distribution system for the purpose of meeting local or regional (substation level) peak loads and/or displacing the need to build additional (or upgrade) local distribution lines.
[Англо-русский глосcарий энергетических терминов ERRA]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > distribution companies
-
27 Anschluß
- контактный вывод для присоединения высоковольтного воздушного провода
- вывод химического источника тока
- вывод тензорезистора
вывод тензорезистора
вывод
Элемент конструкции тензорезистора, предназначенный для электрического соединения чувствительного элемента с внешней измерительной цепью.
[ ГОСТ 20420-75]Тематики
Синонимы
EN
DE
FR
вывод химического источника тока
вывод
Часть химического источника тока, предназначенная для присоединения его к внешней электрической цепи.
[ ГОСТ 15596-82]EN
terminal
conductive part of a device, electric circuit or electric network, provided for connecting that device, electric circuit or electric network to one or more external conductors
Source: 151-12-12
[IEV number 482-02-22]FR
borne, f
partie conductrice d'un dispositif, d'un circuit électrique ou d'un réseau électrique, destinée à le connecter à un ou plusieurs conducteurs extérieurs
Source: 151-12-12
[IEV number 482-02-22]Тематики
Классификация
>>>Синонимы
EN
DE
- Anschlusspunkt, m
- Anschluß
- Anschluß der chemischen Stromquelle
- Klemme, f
- Pol, m
FR
- borne, f
контактный вывод для присоединения высоковольтного воздушного провода
-Тематики
- высоковольтный аппарат, оборудование...
EN
DE
Немецко-русский словарь нормативно-технической терминологии > Anschluß
-
28 terminal
2) нефт. тупиковый резервуарный парк3) нефт. перевалочная база4) ж.-д., мор. терминал5) аэровокзал9) концевая муфта ( кабеля)11) оконечное устройство, терминал || оконечный, терминальный12) вчт. конечный слог; конечное слово15) мор. причал16) порт назначения•-
air freight terminal
-
air terminal
-
alphanumeric terminal
-
alphameric terminal
-
area composition terminal
-
ASCII terminal
-
asynchronous terminal
-
audio terminal
-
axial terminal
-
battery terminal
-
block terminal
-
BTR terminal
-
buffered terminal
-
bulk terminal
-
cable terminal
-
carrier terminal
-
cathode-ray tube terminal
-
cell terminal
-
character terminal
-
circuit terminal
-
coil terminals
-
cold storage terminal
-
color graphic terminal
-
communications terminal
-
communication terminal
-
computer terminal
-
condenser-type terminal
-
conductor terminal
-
congested terminal
-
connection terminal
-
console terminal
-
container terminal
-
control terminal
-
copy input terminal
-
correcting terminal
-
CRT terminal
-
data terminal
-
data-entry terminal
-
dedicated memory terminal
-
deep-sea terminal
-
design terminal
-
desktop terminal
-
destination terminal
-
dial-up terminal
-
digital terminal
-
direct memory access terminal
-
discharge terminal
-
display terminal
-
distribution terminal
-
dry gas terminal
-
dumb terminal
-
earth terminal
-
edge terminal
-
Edison screw terminal
-
editing terminal
-
edit terminal
-
executive terminal
-
feedthrough terminal
-
floating terminal
-
freight terminal
-
gas pipeline terminal
-
gas terminal
-
gateway terminal
-
general cargo terminal
-
graphical terminal
-
graphic terminal
-
gravity loading terminal
-
ground terminal
-
group terminal
-
handheld terminal
-
hardcopy terminal
-
high intelligent terminal
-
high-voltage terminal
-
home terminal
-
initiating terminal
-
input terminal
-
insertion terminal
-
insert terminal
-
intelligent terminal
-
interactive terminal
-
intermodal terminal
-
junction terminal
-
keyboard terminal
-
lead terminal
-
light-wave terminal
-
line terminal
-
loading terminal
-
lug terminal
-
machine interface terminal
-
main terminals
-
makeup terminal
-
marine terminal
-
markup terminal
-
master terminal
-
measuring terminal
-
mobile terminal
-
multipoint terminal
-
negative terminal
-
network terminal
-
neutral terminal
-
nonintelligent terminal
-
office terminal
-
offshore terminal
-
oil-loading terminal
-
on-premise terminal
-
onshore terminal
-
output terminal
-
package terminal
-
packet-mode terminal
-
packet terminal
-
page view terminal
-
passenger terminal
-
phase terminal
-
pin-type terminal
-
pin terminal
-
plug terminal
-
point-of-sale terminal
-
pole terminal
-
port terminal
-
positive terminal
-
printer terminal
-
programmable terminal
-
prong-type terminal
-
prong terminal
-
quiescent terminal
-
radio terminal
-
railway terminal
-
raster-scan graphic terminal
-
receiving terminal
-
remote terminal
-
ring terminal
-
route terminal
-
sales gas terminal
-
screw terminal
-
sea terminal
-
secured terminal
-
shopfloor terminal
-
slave terminal
-
smart terminal
-
snap terminal
-
softcopy terminal
-
spade-type terminal
-
spade terminal
-
split terminal
-
stand-alone terminal
-
subscriber terminal
-
supply terminal
-
switching terminal
-
synchronous terminal
-
system control terminal
-
tab terminal
-
tanker terminal
-
tape correction terminal
-
telecommunications terminal
-
telecommunication terminal
-
teller terminal
-
testing terminal
-
test terminal
-
text editing terminal
-
text input terminal
-
touch-sensitive terminal
-
touch terminal
-
transfer terminal
-
transshipment terminal
-
typesetting terminal
-
unloading terminal
-
user terminal
-
video display terminal
-
video terminal
-
virtual terminal
-
voice terminal
-
welding terminals
-
wire terminal
-
wiring terminal
-
work-station factory terminal
-
wrapping terminal
-
wrap terminal
-
zero terminal -
29 сеть ультравысокого напряжения
Большой англо-русский и русско-английский словарь > сеть ультравысокого напряжения
-
30 сеть ультравысокого напряжения
( выше 1000 кВ) ultra-high voltage power networkАнгло-русский словарь технических терминов > сеть ультравысокого напряжения
-
31 GIS
- свидетельство
- КРУ с газовой изоляцией
- комплектное распределительное устройство элегазовое
- комплектное распределительное устройство с элегазовой изоляцией
- глобальное информационное общество
- ГИС
- географическая информационная система (ГИС)
- географическая информационная система
- газоизолированная подстанция
- выключатель элегазовый
- выключатель с газовой изоляцией
выключатель с газовой изоляцией
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
выключатель элегазовый
Выключатель газовый, контакты которого размыкаются и замыкаются в элегазе (шестифтористой сере).
[ ГОСТ Р 52565-2006]EN
sulphur hexafluoride circuit-breaker
SF6 circuit-breaker
a circuit-breaker in which the contacts open and close in sulphur hexafluoride
[IEV number 441-14-31]FR
disjoncteur à hexafluorure de soufre
disjoncteur à SF6
disjoncteur dont les contacts s'ouvrent et se ferment dans l'hexafluorure de soufre
[IEV number 441-14-31]Для РУ напряжением 110 кВ и выше (вплоть до 1150 кВ) наиболее широко используются воздушные выключатели, где гашение дуги осуществляется потоком сжатого воздуха. Однако в последнее время они вытесняются элегазовыми выключателями, в которых в качестве дугогасящей среды используется электроотрицательный газ — шестифтористая сера (элегаз). Такие выключатели создаются для герметичных распределительных устройств (ГРУ), а также для наружной установки. Использование элегаза в качестве дугогасящей среды обусловлено его высокими изоляционными и дугогасящими свойствами. Это позволяет создать более совершенные выключатели с меньшим числом дугогасительных разрывов, с меньшими габаритами и более надежные в эксплуатации.
[А. И. Афанасьев и др. Электрические аппараты высокого напряжения. - 2-е изд., доп. СПбГТУ, 2000, 503 с.]Тематики
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
EN
DE
FR
ГИС
Географическая информационная система
геоинформационная система
Информационная система, обеспечивающая сбор, хранение, обработку, доступ, отображение и распространение пространственно-координированных данных (пространственных данных). ГИС содержит данные о пространственных обьектах в форме их цифровых представлений (векторных, растровых, квадротомических и иных), включает соответствующий задачам набор функциональных возможностей ГИС, в которых реализуются операции геоинформационных технологий, или ГИС-технологий (GIS tehnology), поддерживается программным, аппаратным, информационным, нормативно-правовым, кадровым и организационным обеспечением. По территориапьному охвату различают глобальные, или планетарные ГИС (global GIS), субконтинентальные ГИС, национальные ГИС, зачастую имеющие статус государственных, региональные ГИС (regional GIS), субрегиональные ГИС и локальные, или местные ГИС (lokal GIS). ГИС различаются предметной областью информационного моделирования, к примеру, городские ГИС, или муниципальные ГИС, МГИС (urban GIS), природоохранные ГИС (environmental GIS) и т.п.; среди них особое наименование, как особо широко распространенные, получили земельные информационные системы. Проблемная ориентация ГИС определяется решаемыми в ней задачами (научными и прикладными), среди них инвентаризация ресурсов (в том числе кадастр), анализ, оценка, мониторинг, управление и ппантрование, поддержка принятия решений. Интегрированные ГИС, ИГИС (integrated GIS, IGIS) совмещают функциональные возможности ГИС и систем цифровой обработки изображений (материалов дистанционного зондирования) в единой интегрированной среде. Полимасштабные, или масштабно-независимые ГИС (multiscale GIS) основаны на множественных, или полимасштабных представпениях пространственных объектов (multiple representation, multiscale representation), обеспечивая графическое или картографическое вопроизведение данных на любом из избранных уровней масштабного ряда на основе единственного набора данных с наибольшим пространственным разрешением. Пространственно-временные ГИС (spatio-temporal GIS) оперируют пространственно-временными данными. Реализация геоинформационных проектов (GIS project), создание ГИС в широком смысле слова, включает этапы предпроектных исследований (feasibility stady), в том числе изучение требований пользователя (user requirements) и функциональных возможностей используемых программных средств ГИС, технико-экономическое обоснование, оценку соотношения "затраты/прибыль" (costs/benefits); системное проектирование ГИС (GIS designing), включая стадию пилот-проекта (pilot-project), разработку ГИС (GIS development); ее тестирование на небольшом территориальном фрагменте, или тестовом участке (test area), прототипирование, или создание опытного образца, прототипа (prototype); внедрение ГИС (GIS implementation), эксплуатацию и использование. Научные, технические, технологические и прикладные аспекты проектирования, создания и использования ГИС изучаются геоинформатикой.
[ http://www.morepc.ru/dict/]Тематики
Синонимы
EN
газоизолированная подстанция
Электрическая подстанция, оборудование которой заключено в металлический кожух, заполненный изолирующим газом.
[ ГОСТ 24291-90]EN
gas insulated metal-enclosed substation
a substation which is made up with only gas insulated metal enclosed switchgear
[IEV number 605-02-14 ]FR
poste sous enveloppe métallique à isolation gazeuse
poste ne comportant que de l'appareillage sous enveloppe métallique à isolation gazeuse
[IEV number 605-02-14 ]Тематики
EN
DE
- Gasoisolirte metaligekapselte Station
- Station, gasisolierte metallgekapselte
FR
географическая информационная система
—
[ http://www.iks-media.ru/glossary/index.html?glossid=2400324]Тематики
- электросвязь, основные понятия
EN
географическая информационная система
ГИС
—
[Упрощение процедур торговли: англо-русский глоссарий терминов (пересмотренное второе издание) НЬЮ-ЙОРК, ЖЕНЕВА, МОСКВА 2011 год]EN
geographic information system
GIS
[Trade Facilitation Terms: An English - Russian Glossary (revised second edition) NEW YORK, GENEVA, MOSCOW 2456]Тематики
Синонимы
EN
глобальное информационное общество
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]Тематики
EN
КРУ с газовой изоляцией
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
комплектное распределительное устройство с элегазовой изоляцией
КРУЭ
-Параллельные тексты EN-RU
The circuit breaker forms the central element of the gas insulated switchgear.
[Siemens]Силовой выключатель является основным элементом КРУЭ.
[Перевод Интент]Switchgears of type 8DQ1 are metal-enclosed, gas-insulated switchgears for operating voltages up to 345 / 420 kV. They consist of individual switchgear bays.
[Siemens]КРУЭ 8DQ1 представляет собой комплектное распределительное устройство в металлической оболочке с элегазовой изоляцией на напряжение до 345/420 кВ. КРУЭ состоит из отдельных ячеек.
[Перевод Интент]These operating instructions are valid for the type and version of the metal-enclosed gas-insulated switchgear specified on the title page.
[Siemens]Данный документ представляет собой Руководство по эксплуатации комплектного распределительного устройства в металлической оболочке с элегазовой изоляцией (КРУЭ) тип и исполнение которого указаны на обложке.
[Перевод Интент]Тематики
- комплектное распред. устройство (КРУ)
Синонимы
EN
комплектное распределительное устройство элегазовое
РУ, в котором основное оборудование заключено в оболочки, заполненные элегазом (SF6), служащим изолирующей и/или дугогасящей средой.
[ПУЭ]EN
gas-insulated metal-enclosed switchgear
metal-enclosed switchgear in which the insulation is obtained, at least partly, by an insulating gas other than air at atmospheric pressure
NOTE – This term generally applies to high-voltage switchgear and controlgear
[IEV number 441-12-05]FR
appareillage sous enveloppe métallique à isolation gazeuse
appareillage de connexion sous enveloppe métallique dans laquelle l'isolation est obtenue, au moins partiellement, par un gaz isolant autre que l'air à pression atmosphérique
NOTE – Ce terme s'applique généralement à l'appareillage à haute tension.
[IEV number 441-12-05]
Рис. SiemensКРУЭ 8DN8
Тематики
- комплектное распред. устройство (КРУ)
Синонимы
Сопутствующие термины
EN
- gas-insulated metal-enclosed switchgear
- gas-insulated switchgear
- GIS
- SF6 gas-insulated metal-enclosed switchgear
DE
- gasisolierte, metallgekapselte Schaltanlagen
FR
2.1.35 свидетельство: Документ, официально подтверждающий какой-либо факт, имеющий юридическое значение, либо право лица (об окончании учебного заведения).
2.2. В настоящем руководстве применены следующие сокращения на русском языке:
АМИС
Автоматическая метеорологическая измерительная система
АМРК
Автоматизированный метеорологический радиолокационный комплекс
АМСГ
Авиационная метеорологическая станция (гражданская)
АМЦ
Авиационный метеорологический центр
БАМД
Банк авиационных метеорологических данных
ВМО
Всемирная метеорологическая организация
ВНГО
Высота нижней границы облаков
ВПП
Взлетно-посадочная полоса
ВС
Воздушное судно
ВСЗП
Всемирная система зональных прогнозов
ВЦЗП
Всемирный центр зональных прогнозов
ГАМЦ
Главный авиационный метеорологический центр
ГИС
Географическая информационная система
ГОУ ИПК
Государственное образовательное учреждение «Институт повышения квалификации»
ГСТ
Глобальная система телесвязи
ГУ ГРМЦ
Государственное учреждение «Главный радиометеорологический центр»
ДОТ
Дистанционные образовательные технологии
ИТ
Информационные технологии
КПК
Курсы повышения квалификации
КРАМС
Комплексная радиотехническая аэродромная метеорологическая станция
МРЛ
Метеорологический радиолокатор
НГЭА
Нормы годности к эксплуатации гражданских аэродромов
НОО
Непрерывное образование и обучение
НПР
Непрерывное профессиональное развитие
ОВД
Обслуживание воздушного движения
ОГ
Оперативная группа
ОМС
Орган метеорологического слежения
УВД
Управление воздушным движением
2.3. В настоящем руководстве применены следующие сокращения на английском языке:
AFTN
Aeronautical Fixed Telecommunication Network
Авиационная фиксированная сеть электросвязи
AIRMET
AIRman's METeorological information
Выпускаемая органом метеорологического слежения информация о фактическом или ожидаемом возникновении определенных явлений погоды по маршруту полета, которые могут повлиять на безопасность полетов воздушных судов на малых высотах
ATIS
Automatic Terminal Information Service
Автоматическая аэродромная служба информации
BUFR
Binary Universal Form for the Representation of meteorological date
Двоичная универсальная форма для представления метеорологических данных
GIS
Geographic Information Systems
Географическая информационная система
GAMET
General Aviation METeorological forecast
Зональный прогноз, составляемый открытым текстом с сокращениями для полетов на малых высотах применительно к району полетной информации или его субрайону (подрайону) метеорологическим органом и передаваемый метеорологическим органам соседних районов полетной информации
GRIB
GRIdded Binary
Бинарный код (прогностические данные метеорологических элементов в узлах регулярной сетки)
GTS
Global Telecommunication System
Глобальная система телесвязи (в рамках ВМО)
IAVW
International Airways Volcano Watch
Служба слежения за вулканической деятельностью на международных авиатрассах
ICAO
International Civil Aviation Organization
Международная организация гражданской авиации
ISCS
International Satellite Communications System
Международная спутниковая система телесвязи (обеспечивается США)
METAR
METeorological Aerodrome Report
Метеорологическая сводка по аэродрому (код METAR)
MOR
Meteorological Optical Range
Метеорологическая оптическая дальность
OPMET
Operational METeorological information
Оперативная метеорологическая информация (данные)
QFE
Atmospheric pressure at the runway threshold (or at the aerodrome elevation)
Атмосферное давление на уровне порога ВПП (или аэродрома)
QNH
Atmospheric pressure at the aerodrome elevation corrected to the mean sea level according to standard atmosphere
Атмосферное давление на уровне аэродрома, приведенное к среднему уровню моря по стандартной атмосфере
RVR
Runway Visual Range
Дальность видимости на ВПП
SADIS
SAtellite Distribution System
Спутниковая система рассылки метеорологических данных (обеспечивается Великобританией)
SIGMET
SIGnificant METeorological information
Выпускаемая органом метеорологического слежения информация о фактическом или ожидаемом возникновении определенных явлений погоды по маршруту полета, которые могут повлиять на безопасность полетов воздушных судов
SIGWX
SIGnificant Weather
Особые явления погоды
SPECI
SPECIal report
Специальная метеорологическая сводка (по аэродрому)
TAF
Terminal Aerodrome Forecast
Прогноз по аэродрому
TCAC
Tropical Cyclone Aadvisory Center
Консультативный центр по тропическим циклонам
TREND
TREND
Прогноз для посадки
VAAC
Volcanic Ash Advisory Center
Консультативный центр по вулканическому пеплу
VOLMET
Volume of meteorological information for aircraft in flight
Объем метеорологической информации для воздушных судов, находящихся в полете
Англо-русский словарь нормативно-технической терминологии > GIS
32 DOL
- эффект операционного рычага
- пускатель прямого действия
- прямой пуск вращающегося электродвигателя
- Министерство труда (США)
- концентрация растворённого кислорода
концентрация растворённого кислорода
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
Министерство труда (США)
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
пускатель прямого действия
Пускатель, одноступенчато подающий сетевое напряжение на выводы двигателя.
(МЭС 441-14-40)
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]
Пускатели переменного тока для прямого непосредственного пуска (с полным напряжением)
Пускатели, предназначенные для пуска двигателя, разгона его до номинальной скорости, защиты двигателя и подключенных к нему цепей от рабочих перегрузок и отключения питания двигателя.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]EN
direct-on-line starter
a starter which connects the line voltage across the motor terminals in one step
[IEV number 441-14-40]FR
démarreur direct
démarreur qui applique la tension d'alimentation sur les bornes du moteur en une seule manoeuvre
[IEV number 441-14-40]Параллельные тексты EN-RU
Direct-on-line starters
Starters which connect the line voltage across the motor terminals in one step, intended to start and accelerate a motor to normal speed.
They shall ensure switching and protection functions as prescribed in the general definition.
[ABB]Пускатели прямого действия
Пускатели, одноступенчато подающие сетевое напряжение на зажимы двигателя и предназначенные для его пуска и разгона до номинальной скорости.
Кроме того, они должны обеспечивать коммутацию и защиту в соответствии с общим определением.
[Перевод Интент]Тематики
EN
DE
FR
эффект операционного рычага
эффект производственного рычага
Эффект операционного рычага - выражение того факта, что любое изменение выручки от реализации порождает изменение прибыли. Сила воздействия операционного рычага вычисляется как частное от деления выручки от реализации после возмещения переменных затрат на прибыль.
[ http://www.lexikon.ru/dict/fin/a.html]Тематики
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > DOL
33 démarrage direct
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Франко-русский словарь нормативно-технической терминологии > démarrage direct
34 Anlauf mit direktem Einschalten
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Anlauf mit direktem Einschalten
35 direct starting
прямой пуск
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > direct starting
36 across-the-line starting (US)
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > across-the-line starting (US)
37 direct line starting
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > direct line starting
38 direct operation of a motor
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > direct operation of a motor
39 direct-on-line starting
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > direct-on-line starting
40 circuit
2) канал3) т. граф. простая цепь, контур•- active circuit
- acyclic circuit
- adding circuit
- add circuit
- addressing circuit
- advancing circuit
- alarm circuit
- amplifying circuit
- analogous circuit
- analog circuit
- AND-to-OR circuit
- antialiasing circuit
- anticoincidence circuit
- antihunting circuit
- antihunt circuit
- aperiodic circuit
- arithmetic circuit
- arithmetical circuit
- astable circuit
- averaging circuit
- balanced circuit
- basis circuit
- beam-lead integrated circuit
- benchmark circuit
- binary-valued digital circuit
- binary-valued circuit
- bipolar circuit
- bistable circuit
- blanking circuit
- bleeder circuit
- bridge circuit
- buffer circuit
- carry circuit
- character selection circuit
- checking circuit
- check circuit
- clamping circuit
- clocked circuit
- clock-recovery circuit
- closed circuit
- code disjoint circuit
- coincidence circuit
- combinational circuit
- combinatorial circuit
- communication circuit
- comparator circuit
- compare circuit
- comparison circuit
- complementary circuit
- complementary integrated circuit
- complementary transistor logic circuit
- complex function circuit
- computer circuit
- computer test circuit
- computing circuit
- control circuit
- core-diode circuit
- core-transistor circuit
- correcting circuit
- correction circuit
- counter circuit
- counting circuit
- coupling circuit
- current-limit circuit
- current-operated circuit
- current-summation circuit
- custom product integrated circuit
- custom integrated circuit
- custom-wired integrated circuit
- cutoff circuit
- cycle circuit
- cyclic circuit
- dead-on-arrival integrated circuit
- decode circuit
- decoding circuit
- deenergizing circuit
- deflection circuit
- delay circuit
- densely packed circuit
- differentiating circuit
- digital computing circuit
- diode circuit
- diode-coupled circuit
- diode-transistor logic circuit
- direct-coupled circuit
- direct-coupled transistor logic circuit
- direct-current circuit
- discrete component circuit
- discrete logic-level
- discrete wired circuit
- display circuit
- divide-by-two circuit
- dividing circuit
- double-sided printed circuit
- doubling circuit
- drive circuit
- dry circuit
- dual circuit
- duplex circuit
- Eccles-Jordan circuit
- edge-activated circuit
- emitter-coupled circuit
- emitter-coupled logic circuit
- emitter-emitter-coupled logic circuit
- equality circuit
- equivalent circuit
- etched circuit
- Euler circuit
- except circuit
- fanout-free circuit
- fast-switching circuit
- fault detection circuit
- fault-free circuit
- fault-secure circuit
- faulty circuit
- feedback circuit
- ferrite-diode circuit
- ferrite-transistor circuit
- ferroresonant computing circuit
- film integrated circuit
- flag-testing circuit
- flat-pack integrated circuit
- flexible printed circuit
- flexible circuit
- flip-chip integrated circuit
- flip-flop circuit
- frame-grounding circuit
- frequency-halving circuit
- function circuit
- gate circuit
- Goto-pair circuit
- half-duplex circuit
- halving circuit
- Hamilton circuit
- hand-designed circuit
- hardwired circuit
- high-speed circuit
- high-threshold logic circuit
- holding circuit
- hybrid circuit
- idler circuit
- imbedded circuit
- IMOS circuit
- impulse circuit
- inhibit circuit
- input circuit
- integrated circuit
- integrating circuit
- integro-differential circuit
- interchange circuit
- interface circuit
- interfacing circuit
- interlock circuit
- invert circuit
- ion-implanted MOS circuit
- irredundant circuit
- Josephson integrated circuit
- junction transistor circuit
- ladder circuit
- lag-lead circuit
- laminar circuit
- large arithmetic circuit
- large-scale integrated circuit
- large-scale integration circuit
- latch circuit
- lead-lag circuit
- leased circuit
- level circuit
- linear circuit
- linear integrated circuit
- linearity circuit
- liquid logic circuit
- load circuit
- locked pair circuit
- locking circuit
- logic circuit
- logical circuit
- low-threshold integrated circuit
- LSI circuit
- lumped circuit
- magnetic circuit
- magnetic-core circuit
- majority circuit
- match circuit
- material equivalence circuit
- matrix circuit
- maximum-remembering circuit
- measuring circuit
- medium-scale integration circuit
- memory circuit
- memory-decoder circuit
- message circuit
- metal-oxide-semiconductor circuit
- microamp circuit
- microelectronic integrated circuit
- microminiature circuit
- microwave circuit
- mil spec integrated circuit
- milliwatt circuit
- miniature circuit
- minimum-remembering circuit
- mixed-level circuit
- mixing circuit
- modularized circuit
- molecular integrated circuit
- monitoring circuit
- monolithic integrated circuit
- monostable circuit
- MOS circuit
- MOS integrated circuit
- MOS LSI circuit
- MSI circuit
- multichip integrated circuit
- multifunction integrated circuit
- multilayer circuit
- multilevel circuit
- multiple output circuit
- multiplying circuit
- multipoint circuit
- multistable circuit
- multistage circuit
- nanosecond circuit
- n-channel circuit
- network circuit
- noise-balancing circuit
- noncoincidence circuit
- noncutoff circuit
- non-self-checking circuit
- one-core-per-bit circuit
- one-generator equivalent circuit
- one-out-of-four selecting circuit
- one-shot circuit
- open circuit
- optical commutation circuit
- optical memory circuit
- optically coupled circuit
- optoelectronic circuit
- output circuit
- packaged circuit
- packed circuit
- p-channel circuit
- phantom circuit
- phase-comparison circuit
- phase-inverting circuit
- picosecond circuit
- pilot circuit
- plastic-embedded circuit
- point-to-point circuit
- power circuit
- power monitoring circuit
- power-fail circuit
- printed circuit
- priority circuit
- propagation circuit
- protection circuit
- pulse circuit
- pulse-actuated circuit
- pulse-broadening circuit
- pulse-regenerating circuit
- pulse-shaping circuit
- pulse-stretching circuit
- pulse-switching circuit
- pumped tunnel-diode transistor logic circuit
- pumping circuit
- quenching circuit
- race-free circuit
- radio-frequency circuit
- random-logic circuit
- ratioed circuit
- reading circuit
- received-data circuit
- receiving circuit
- reconfigurable integrated circuit
- redundant circuit
- reference circuit
- refreshing circuit
- relaxation circuit
- reset circuit
- retriggerable circuit
- rewriting circuit
- ring circuit
- rounding circuit
- sample-hold circuit
- saturated circuit
- scale-of-N circuit
- scale-of-two circuit
- scaling circuit
- schematic circuit
- Schmitt trigger circuit
- Schmitt circuit
- screen printed circuit
- selection circuit
- select circuit
- self-checking circuit
- self-testing circuit
- self-timed circuit
- semiconductor circuit
- send-request circuit
- sequential circuit
- shifting circuit
- shift circuit
- short circuit
- shunt-peaking circuit
- sign-controlled circuit
- silicon integrated circuit
- silicon-on-sapphire integrated circuit
- simplex circuit
- single-chip circuit
- single-ended circuit
- single-level circuit
- single-phase circuit
- single-shot circuit
- small-scale integration circuit
- solid-state circuit
- solid circuit
- SOS integrated circuit
- squaring circuit
- SSI circuit
- stabilizing circuit
- stamped circuit
- start-stop circuit
- steering circuit
- storage circuit
- storage-selection circuit
- strongly fault-secure circuit
- subtraction circuit
- summing circuit
- sweep circuit
- switching circuit
- symbolic circuit
- synchronizing circuit
- synthesis circuit
- thick-film circuit
- thin-film circuit
- threshold circuit
- time-anticoincidence circuit
- time-base circuit
- time-coincidence circuit
- time-delay circuit
- toll circuit
- totally self-checking circuit
- transistor circuit
- transistor-core circuit
- transistor-resistor circuit
- transistor-transistor-logic circuit
- translation circuit
- transmitted-data circuit
- transmitting circuit
- tree circuit
- trigger -action circuit
- trigger circuit
- trunk circuit
- tunnel diode circuit
- twin-tunnel-diode circuit
- twin circuit
- two-cores-per-bit circuit
- two-input circuit
- two-level circuit
- two-way circuit
- ultra-large-scale integration circuit
- unidirectional circuit
- unpackaged circuit
- unpacked circuit
- very-high-speed integrated circuit
- very-large-scale integration circuit
- virtual circuit
- VLSI circuit
- voice circuit
- voice-grade circuit
- voltage-control circuit
- voltage-doubling circuit
- voltage-multiplying circuit
- voltage-summation circuit
- voter circuit
- wave-shaping circuit
- whole-wafer circuit
- wired AND circuit
- wired OR circuit
- wire-wrapped circuit
- writing circuit
- zero circuitEnglish-Russian dictionary of computer science and programming > circuit
СтраницыСм. также в других словарях:
High-voltage direct current — HVDC or high voltage, direct current electric power transmission systems contrast with the more common alternating current systems as a means for the bulk transmission of electrical power. The modern form of HVDC transmission uses technology… … Wikipedia
High-speed rail in Europe — High speed rail is emerging in Europe as an increasingly popular and efficient means of transportation. The first high speed rail lines in Europe, built in the 1980s and 1990s, improved travel times on intra national corridors. Since then,… … Wikipedia
Voltage multiplier — Villard cascade voltage multiplier. A voltage multiplier is an electrical circuit that converts AC electrical power from a lower voltage to a higher DC voltage, typically by means of a network of capacitors and diodes. Voltage multipliers can be… … Wikipedia
Network isolator — Network isolators are installed as part of a copper Ethernet system, as galvanic isolators. Network data continues to be transmitted across an electrically non conducting barrier, through the applied principle of electromagnetic induction,… … Wikipedia
Network information system — (abbreviation: NIS) is an information system for managing networks, such as electricity network, water supply network, gas supply network, or telecommunications network. NIS may manage all data relevant to the network, e.g. all components and… … Wikipedia
Network analysis (electrical circuits) — Linear Network Analysis Elements … Wikipedia
Voltage divider — In electronics, a voltage divider (also known as a potential divider) is a simple linear circuit that produces an output voltage ( V out) that is a fraction of its input voltage ( V in). Voltage division refers to the partitioning of a voltage… … Wikipedia
Voltage regulator tube — A voltage regulator tube (VR tube) is an electronic component used as a shunt regulator to hold a voltage constant at a pre determined level.Physically, these devices resemble vacuum tubes, but there are two main differences: * Their glass… … Wikipedia
Voltage source — In electric circuit theory, an ideal voltage source is a circuit element where the voltage across it is independent of the current through it. A voltage source is the dual of a current source. In analysis, a voltage source supplies a constant DC… … Wikipedia
High-speed rail in Germany — Construction on first German high speed lines began shortly after that of the French LGVs ( lignes à grande vitesse , high speed lines). Legal battles caused significant delays, so that the InterCityExpress (ICE) trains were deployed ten years… … Wikipedia
High-Definition Multimedia Interface — Infobox connector name=High Definition Multimedia Interface type=Digital audio/video connector logo= caption=HDMI cable and HDMI official logo designer=HDMI Founders design date=December 2002 manufacturer=HDMI Adopters production date=2003… … Wikipedia
Перевод: со всех языков на русский
с русского на все языки- С русского на:
- Все языки
- Со всех языков на:
- Все языки
- Английский
- Арабский
- Испанский
- Немецкий
- Русский
- Французский