-
21 высокочастотное плазменное наплавление кварцевого стекла
высокочастотное плазменное наплавление кварцевого стекла
плазменный способ
Наплавление кварцевого стекла в высокочастотной низкотемпературной плазме.
[ ГОСТ 16548-80]Тематики
- оптика, оптические приборы и измерения
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > высокочастотное плазменное наплавление кварцевого стекла
-
22 высокочастотный электрохирургический стоматологический аппарат
высокочастотный электрохирургический стоматологический аппарат
Ндп. стоматологический диатермокоагулятор
Стоматологический аппарат для хирургического воздействия на мягкие ткани полости рта токами высокой частоты
[ ГОСТ 26322-84]Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > высокочастотный электрохирургический стоматологический аппарат
-
23 высотно-частотная характеристика
высотно-частотная характеристика
Кривая, выражающая зависимость действующих высот отражения слоя от частоты излучаемых радиоволн
[ ГОСТ 21879-88]
высотно-частотная характеристика
По ГОСТ 24375-80
[ ГОСТ 25645.113-84]Тематики
Обобщающие термины
EN
FR
Русско-французский словарь нормативно-технической терминологии > высотно-частотная характеристика
-
24 Согласующий сигнальный трансформатор высокой частоты
- Transformateur d’adaptation à haute fréquence
24. Согласующий сигнальный трансформатор высокой частоты
Трансформатор высокой частоты
D. Anpassender Signaltransformator der Hochfrequenz
E. Matching high-frequency transformer
F. Transformateur d’adaptation à haute fréquence
Источник: ГОСТ 20938-75: Трансформаторы малой мощности. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > Согласующий сигнальный трансформатор высокой частоты
-
25 номинальное напряжение ОПН
номинальное напряжение
Uн
Действующее значение напряжения промышленной частоты, которое ограничитель может выдерживать в течение 10 с в процессе рабочих испытаний. Номинальное напряжение должно быть не менее 1,25 наибольшего длительно допустимого рабочего напряжения.
[ ГОСТ Р 52725-2007]EN
rated voltage of an arrester
Ur
maximum permissible r.m.s. value of power-frequency voltage between its terminals at which it is designed to operate correctly under temporary overvoltage conditions as established in the operating duty tests
NOTE 1 The rated voltage is used as a reference parameter for the specification of operating characteristics.
NOTE 2 The rated voltage as defined in this standard is the 10 s power-frequency voltage used in the operating duty test after high-current or long-duration impulses. Tests used to establish the voltage rating in IEC 60099-1, as well as some national standards, involve the application of repetitive impulses at nominal current with power-frequency voltage applied. Attention is drawn to the fact that these two methods used to established rating do not necessarily produce equivalent values (a resolution to this discrepancy is under consideration).
[IEC 60099-4, ed. 2.0 (2004-05)]FR
tension assignée d'un parafoudre
Ur
valeur maximale de la tension efficace à fréquence industrielle admissible entre ses bornes pour laquelle le parafoudre est prévu pour fonctionner correctement dans des conditions de surtension temporaires comme il est défini dans les essais de fonctionnement
NOTE 1 La tension assignée est utilisée comme paramètre de référence pour la spécification des caractéristiques de fonctionnement.
NOTE 2 La tension assignée comme définie dans la présente norme est la tension à fréquence industrielle de 10 s, utilisée pour vérifier la stabilité après application des chocs de courant de grande amplitude ou de longue durée lors de l'essai de fonctionnement. Les essais utilisés pour définir la tension assignée dans la CEI 60099-1, ainsi que dans certaines normes nationales, impliquent l'application de chocs répétés au courant nominal pendant que la tension à fréquence industrielle est appliquée. On attire l'attention sur le fait que ces deux méthodes utilisées pour définir les valeurs assignées ne produisent pas nécessairement des valeurs équivalentes (une résolution de cette différence est à l'étude).
[IEC 60099-4, ed. 2.0 (2004-05)]Тематики
- высоковольтный аппарат, оборудование...
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение ОПН
-
26 прямой пуск вращающегося электродвигателя
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Русско-французский словарь нормативно-технической терминологии > прямой пуск вращающегося электродвигателя
-
27 классификационный ток ОПН
классификационный ток ОПН
Iкл
Амплитудное значение (более высокое амплитудное значение из двух полярностей, если ток асимметричен) активной составляющей тока промышленной частоты, которое используется для определения классификационного напряжения ОПН и нормируется изготовителем.
[ ГОСТ Р 52725-2007]EN
reference current of an arrester
peak value (the higher peak value of the two polarities if the current is asymmetrical) of the resistive component of a power-frequency current used to determine the reference voltage of the arrester
NOTE 1 The reference current will be high enough to make the effects of stray capacitances at the measured reference voltage of the arrester units (with designed grading system) negligible and is to be specified by the manufacturer.
NOTE 2 Depending on the nominal discharge current and/or line discharge class of the arrester, the reference current will be typically in the range of 0,05 mA to 1,0 mA per square centimetre of disc area for single column arresters.
[IEC 60099-4, ed. 2.0 (2004-05)]FR
courant de référence d'un parafoudre
valeur de crête (la plus grande des deux polarités si le courant est dissymétrique) de la composante résistive du courant à fréquence industrielle utilisée pour déterminer la tension de référence d'un parafoudre.
NOTE 1 Il convient que le courant de référence soit suffisamment élevé pour rendre négligeables les effets des capacités parasites aux tensions de référence mesurées sur les éléments de parafoudre (avec leur système de répartition) et qu’il soit spécifié par le constructeur.
NOTE 2 Fonction du courant de décharge nominal et/ou de la classe de décharge de ligne du parafoudre, il convient que le courant de référence soit typiquement dans la gamme de 0,05 mA à 1,0 mA par centimètre carré de surface de disque pour les parafoudres à colonne unique
[IEC 60099-4, ed. 2.0 (2004-05)]Тематики
- высоковольтный аппарат, оборудование...
EN
FR
Русско-французский словарь нормативно-технической терминологии > классификационный ток ОПН
-
28 пол плавающий
пол плавающий
Пол, отделённый от основания и стен амортизирующими прослойками или изолирующими устройствами для повышения звукоизоляции смежных помещений
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
floating floor
The upper layer of floor construction supported on battens, mountings or a resilient sheet membrane of damping material such as expanded polystyrene or mineral wool to provide acoustic isolation.
floating floor
A floating floor is a floor that does not need to be nailed or glued to the subfloor. The term floating floor refers to the installation method, but is often used synonymously with laminate flooring in a domestic context.
A sprung floor is a special type of floating floor designed to enhance sports or dance performance. In general though the term refers to a floor used to reduce noise or vibration.
A domestic floating floor might be constructed over a subfloor or even over an existing floor. It can consist of a glass fibre, felt or cork layer for sound insulation with neoprene pads holding up a laminate floor. There is a gap between the floating floor and the walls to decouple them and allow for expansion; this gap is covered with skirting boards or mouldings.
Floating floors as used in sound studios can be either just larger versions of the domestic variety, or much larger constructions with slabs of concrete to keep the resonance frequency down. The manufacture of integrated circuits uses massive floating floors with hundreds of tons in weight of concrete to avoid vibration affecting mask alignment.
Floating floors are one of the requirements for the THX high-fidelity sound reproduction standard for movie theaters, screening rooms, home theaters, computer speakers, gaming consoles, and car audio systems.
While floating floors add to the appeal of a home, they are not recommended for areas that may get wet, i.e. bathrooms and near exterior doors.
[http://en.wikipedia.org/wiki/Floating_floor]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > пол плавающий
- 1
- 2
См. также в других словарях:
High frequency — (HF) radio frequencies are between 3 and 30 MHz. Also known as the decameter band or decameter wave as the wavelengths range from one to ten decameters (ten to one hundred metres). Frequencies immediately below HF are denoted Medium frequency… … Wikipedia
high frequency — ► NOUN ▪ (in radio) a frequency of 3 30 megahertz … English terms dictionary
high frequency — n. any radio frequency between 3 and 30 megahertz … English World dictionary
high frequency — high frequency, adj. the range of frequencies in the radio spectrum between 3 and 30 megahertz. [1890 95] * * * … Universalium
high-frequency — ˈ ̷ ̷| ̷ ̷ ̷ ̷ ̷ ̷ adjective Etymology: high frequency 1. : occurring very frequently drills based on the repetition of high frequency words 2. : relating to high frequency: as a. : involving a radio wave of high frequency used especi … Useful english dictionary
high frequency — noun Date: 1892 a radio frequency between very high frequency and medium frequency see radio frequency table … New Collegiate Dictionary
high frequency — /haɪ ˈfrikwənsi / (say huy freekwuhnsee) noun 1. any radiofrequency between 3 and 30 megahertz. Abbrev.: HF 2. any audible frequency which is high in pitch. –high frequency, adjective …
high-frequency — adjective Of or pertaining to high frequency sound or other radiation … Wiktionary
high-frequency — adj. High frequency is used with these nouns: ↑signal, ↑vibration … Collocations dictionary
high frequency — aukštasis dažnis statusas T sritis Standartizacija ir metrologija apibrėžtis Dažniausiai tai elektromagnetinių virpesių dažnis nuo 10⁵ Hz iki 10¹² Hz. atitikmenys: angl. high frequency vok. Hochfrequenz, f rus. высокая частота, f pranc. haute… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
high frequency — aukštasis dažnis statusas T sritis Standartizacija ir metrologija apibrėžtis Radijo dažnis nuo 3 MHz iki 300 MHz. atitikmenys: angl. high frequency vok. Hochfrequenz, f rus. высокая частота, f pranc. haute fréquence, f … Penkiakalbis aiškinamasis metrologijos terminų žodynas