-
1 grounding connection
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
Англо-русский словарь нормативно-технической терминологии > grounding connection
-
2 potential electrode
The English-Russian dictionary general scientific > potential electrode
-
3 transformer
3) пищ. котёл для получения инвертированного сиропа•-
adapter transformer
-
adjustable transformer
-
air transformer
-
air-blast transformer
-
air-cooled transformer
-
air-core transformer
-
air-natural transformer
-
amorphous-core transformer
- arc furnace transformer -
arc-welding transformer
-
audio-frequency transformer
-
autocompounded current transformer
-
autocompounded voltage transformer
-
autoconnected transformer
-
auxiliary transformer
-
balanced-to-unbalanced transformer
-
balance-to-unbalanced transformer
-
balanced-to-unbalance transformer
-
balance-to-unbalance transformer
-
balanced transformer
-
balancing transformer
-
ballast transformer
-
banked distribution transformers
-
bar-type transformer
-
bell transformer
-
booster transformer
-
bridge transformer
-
busbar current transformer
-
capacitive voltage transformer
-
cascade transformer
-
cast resin transformer
-
center-tapped transformer
-
closed core transformer
-
code transformer
-
combined voltage and current transformer
-
compensated current transformer
-
compensated voltage transformer
-
compound-filled instrument transformer
-
constant-current transformer
-
constant-potential transformer
-
control circuit transformer
-
control transformer
-
converter transformer
-
coreless transformer
-
core-type transformer
-
coupling transformer
-
current transformer
-
decoupling transformer
-
differential transformer
-
diode-split line-output transformer
-
direct-current transformer
-
distribution transformer
-
double-stub transformer
-
double-tuned transformer
-
double-winding transformer
-
driving transformer
-
dry-type transformer
-
dry transformer
-
dry-type forced-air-cooled transformer
-
dry-type self-cooled transformer
-
E transformer
-
earthed transformer
-
earthing transformer
-
effective grounded transformer
-
EHV power transformer
-
excitation transformer
-
extra-high-voltage power transformer
-
feed transformer
-
feeder transformer
-
feeding transformer
-
filter transformer
-
five-legged transformer
-
flash transformer
-
flyback transformer
-
forced-air-cooled transformer
-
forced-oil transformer
-
frame-output transformer
-
furnace transformer
-
gas-filled transformer
-
gas-insulated transformer
-
general transformer
-
general-purpose transformer
-
grounded transformer
-
grounding transformer
-
high-potential transformer
-
high-power transformer
-
high-voltage transformer
-
horizontal-output transformer
-
house transformer
-
hydropneumatic transformer
-
ideal transformer
-
image-output transformer
-
impedance transformer
-
impedance-matching transformer
-
impulse current transformer
-
indoor transformer
-
induction voltage transformer
-
injector transformer
-
input transformer
-
instrument transformer
-
insulated-core transformer
-
insulating transformer
-
integral current transformer
-
interphase transformer
-
intervening current transformer
-
iron-clad transformer
-
iron-core transformer
-
isolating transformer
-
lightning-proof transformer
-
line regulating transformer
-
line transformer
-
linear hydraulic transformer
-
line-output transformer
-
liquid-filled transformer
-
loading transformer
-
low-power transformer
-
low-voltage transformer
-
mains transformer
-
manhole transformer
-
matching transformer
-
measuring transformer
-
micromodular transformer
-
mode transformer
-
molded transformer
-
multiratio current transformer
-
multiratio voltage transformer
-
multiwinding transformer
-
natural-draft transformer
-
network transformer
-
nonmagnetic current transformer
-
nonresonating transformer
-
oil-cooled transformer
-
oil transformer
-
oil-filled instrument transformer
-
oil-immersed forced-air-cooled transformer
-
oil-immersed forced-oil-cooled transformer
-
oil-immersed self-cooled transformer
-
oil-immersed transformer
-
oil-immersed water-cooled transformer
-
one-coil transformer
-
one-to-one transformer
-
on-load tap-changing transformer
-
open-core transformer
-
outdoor transformer
-
output transformer
-
pad-mounted transformer
-
peaking transformer
-
peak transformer
-
phase-shifting transformer
-
pole-type transformer
-
polyphase transformer
-
potential transformer
-
power transformer
-
protection current transformer
-
protection voltage transformer
-
protective transformer
-
pulse transformer
-
pulse-forming transformer
-
radio-frequency transformer
-
reactance-earthed transformer
-
reactor transformer
-
rectifier transformer
-
reducing transformer
-
regulating transformer
-
relay transformer
-
resistance-earthed transformer
-
resonance transformer
-
rotary hydraulic transformer
-
rotary transformer
-
rotatabletransformer
-
saturable current transformer
-
saturable transformer
-
saturating current transformer
-
sealed transformer
-
self-cooled transformer
-
self-protected transformer
-
series regulating transformer
-
series transformer
-
SF6-filled transformer
-
shell-core transformer
-
shell-form
-
shell-type transformer
-
shunt transformer
-
signal transformer
-
single-phase transformer
-
single-turn current transformer
-
small-power transformer
-
solidly earthed transformer
-
spare transformer
-
standard current transformer
-
standard instrument transformer
-
standard potential transformer
-
standby transformer
-
starting transformer
-
step-down transformer
-
step-up transformer
-
subdivided transformer
-
submersible transformer
-
substation transformer
-
supply transformer
-
tank transformer
-
tap-changing transformer
-
tap-changing-under-load transformer
-
tapped transformer
-
teaser transformer
-
testing transformer
-
test transformer
-
thermal transformer
-
three-circuit transformer
-
three-legged transformer
-
three-leg transformer
-
three-phase transformer
-
three-winding transformer
-
through-type current transformer
-
tool transformer
-
toroidal-coretransformer
-
toroidaltransformer
-
track-circuit transformer
-
track transformer
-
traction-feeding transformer
-
triple-wound transformer
-
tuned transformer
-
two-winding transformer
-
unbalanced-to-balanced transformer
-
unbalance-to-balanced transformer
-
unbalanced-to-balance transformer
-
unbalance-to-balance transformer
-
unearthed transformer
-
variable-ratio transformer
-
vertical-output transformer
-
voltage measuring transformer
-
voltage transformer
-
water-cooled transformer
-
welding transformer
-
window-type current transformer
-
zero-phase sequence current transformer -
4 transformer
= trans, = xfmr2) вчт оператор преобразования•- air-core transformer
- antihunt transformer
- audio transformer
- audio-frequency transformer
- autoconnected transformer
- balance-to-unbalance transformer
- balancing transformer
- ballast transformer
- balun transformer
- bell transformer
- bifilar transformer
- booster transformer
- bridge transformer
- bridging transformer
- capacitance transformer
- closed-core transformer
- code transformer
- compensated transformer
- compensating transformer
- compound-filled transformer
- constant-current transformer
- constant-potential transformer
- constant-voltage transformer
- control-circuit transformer
- core transformer
- coreless transformer
- coupling transformer
- current transformer
- decoupling transformer
- delta matching transformer
- differential transformer
- discrete Hilbert transformer
- discriminator transformer
- doorknob transformer
- double-tuned transformer
- E-transformer
- earthed transformer
- earthing transformer
- exponential-line transformer
- filament transformer
- flux transformer
- flyback transformer
- Fourier transformer
- grounded transformer
- grounding transformer
- horizontal output transformer
- hybrid transformer
- ideal transformer
- IF transformer
- impedance transformer
- impedance-matching transformer
- impulse transformer
- injector transformer
- input transformer
- instrument transformer
- intermediate-frequency transformer
- interphase transformer
- interstage transformer
- inverse transformer
- iron-core transformer
- isolation transformer
- laser current transformer
- line transformer
- linear-variable differential transformer
- mains transformer
- matching transformer
- microphone transformer
- mode transformer
- modulator transformer
- molded transformer
- network transformer
- one-coil transformer
- open-core transformer
- optical transformer
- optimal discrete Hilbert transformer
- output transformer
- peaking transformer
- phase-shifting transformer
- phasing transformer
- polyphase transformer
- potential transformer
- power transformer
- protective transformer
- pulse transformer
- pulsing transformer
- push-pull transformer
- quarter-wave transformer
- radio-frequency transformer
- rectifier transformer
- reducing transformer
- regulating transformer
- resonance transformer
- rotary transformer
- rotatable phase-adjusting transformer
- rudimentary flux transformer
- saturable transformer
- shell-type transformer
- similarity transformer
- single-stub transformer
- single-tuned transformer
- step-down transformer
- step-up transformer
- subdivided transformer
- superconducting transformer
- Tesla transformer
- time-variable transformer
- transistor transformer
- transmission-line transformer
- tuned transformer
- unbalance-to-balance transformer
- variable transformer
- variable-voltage transformer
- voltage transformer
- voltage-regulating transformer
- waveguide transformer
- welding transformer
- wide-band transformer -
5 earth
- земной
- земля (в электроустановках)
- земля (в электрической цепи)
- земля
- замыкание на землю (англ.)
- замыкание на землю
- заземлять
- заземление (англ.)
заземление (англ.)
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
заземлять
Выполнять электрическое соединение между данной точкой системы или установки, или оборудования и локальной землей.
Примечание - Соединение с локальной землей может быть:
- преднамеренным;
- непреднамеренным или случайным;
- постоянным или временным.
[ ГОСТ Р МЭК 60050-826-2009]EN
earth, verb
ground (US), verb
make an electric connection between a given point in a system or in an installation or in equipment and local earth
NOTE – The connection to local earth may be:
– intentional, or
– unintentional or accidental
– and may be permanent or temporary.
Source: 195-01-08
[IEV number 826-13-03]FR
mettre à la terre, verbe
réaliser une liaison électrique entre un point donné d'un réseau, d'une installation ou d'un matériel et une terre locale
NOTE – La liaison à la terre locale peut être:
– intentionnelle, ou
– non intentionnelle ou accidentelle
– et peut être permanente ou temporaire.
Source: 195-01-08
[IEV number 826-13-03]Тематики
EN
DE
- erden, Verb
FR
- mettre à la terre, verbe
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
замыкание на землю (англ.)
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
земля (в электрической цепи)
Точка в электрической цепи, имеющая нулевой потенциал относительно общей шины. См. тж. ground.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]Тематики
- электросвязь, основные понятия
EN
земля
Часть Земли, которая находится в электрическом контакте с заземлителем и электрический потенциал которой не обязательно равен нулю.
[ ГОСТ Р МЭК 60050-195-2005]
(локальная) земля
Часть Земли, которая находится в электрическом контакте с заземлителем и электрический потенциал которой необязательно равен нулю.
[ ГОСТ Р МЭК 60050-826-2009]
Вблизи заземлителя потенциал может быть не равен нулю
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
земля
Проводящая масса земли, электрический потенциал которой в любой точке условно принимают равным нулю
[МЭС 826-04-01].
[ ГОСТ Р 61557-1-2006]EN
(local) earth
part of the Earth which is in electric contact with an earth electrode and the electric potential of which is not necessarily equal to zero
[IEV number 195-01-03]FR
terre (locale)
partie de la Terre en contact électrique avec une prise de terre, et dont le potentiel électrique n'est pas nécessairement égal à zéro
[IEV number 195-01-03]Тематики
Синонимы
EN
DE
FR
земной
—
[ http://www.iks-media.ru/glossary/index.html?glossid=2400324]Тематики
- электросвязь, основные понятия
EN
3.16 земля (earth): Проводящая масса земли, электрический потенциал которой в любой точке условно принимают равным нулю.
3.17
Источник: ГОСТ Р 54127-1-2010: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 1. Общие требования оригинал документа
3.1.18 земля (earth): Проводящая масса земли, электрический потенциал которой в любой точке условно принимают равным нулю [МЭС 826-04-01].
Источник: ГОСТ Р МЭК 61557-1-2005: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 1. Общие требования оригинал документа
Англо-русский словарь нормативно-технической терминологии > earth
-
6 device
1) устройство2) установка; агрегат3) аппарат4) механизм5) прибор; измерительное устройство7) компонент; элемент8) схема•devices identical in design — конструктивные аналоги;-
alphanumeric display device-
automatic exposure control device-
bubble memory device-
bucket brigade charge-coupled device-
decision-making device-
drilling bit feed device-
electrical device-
exposure control device-
Gunn-effect device-
Hall-effect device-
hard-copy output device-
household electrical device-
humidity detecting device-
hybrid-type device-
Josephson-effect device-
maneuvering propulsion device-
materials-handling device-
multiport device-
night observation device-
noise dampening device-
photoconducting device-
propulsion device-
protection device-
raster-display device-
registering pin device-
reversible film feeding device-
seed-feeding device-
supply reel braking device-
three-axis device -
7 relay
1) реле || ставить реле2) снабжать релейной защитой; ставить релейную защиту4) трансляция; передача ( сигнала) || транслировать; передавать ( сигнал)5) ретрансляция; переприём || ретранслировать•-
ac relay
-
ac system relays
-
accelerating relay
-
acoustic relay
-
actuating relay
-
alarm relay
-
allotter relay
-
all-to-all relay
-
amplitude comparison relay
-
angle armature relay
-
annunciation relay
-
antifailure automatics relay
-
armature relay
-
automatic reclosing relay
-
back-current relay
-
backup relay
-
balance beam relay
-
balanced relay
-
banked relay
-
biased relay
-
bimetallic-strip relay
-
bistable relay
-
blocking relay
-
block relay
-
brake application relay
-
brake release relay
-
braking relay
-
Buchholz relay
-
calling relay
-
call relay
-
capacitance relay
-
carrier-actuated relay
-
center-stable polarized relay
-
center-stable polar relay
-
central disconnection relay
-
change-of-current relay
-
charging rate relay
-
circuit-control relay
-
clappers-type relay
-
clappers relay
-
clearing relay
-
clock relay
-
closing relay
-
code relay
-
compelling relay
-
conductance relay
-
contact relay
-
contactless relay
-
continuous-duty relay
-
control relay
-
crossing relay
-
current relay
-
current-balance relay
-
current-overload relay
-
cut-in relay
-
cut-off relay
-
dc relay
-
definite minimum time-limit relay
-
definite-time-lag relay
-
delay relay
-
dependent-time measuring relay
-
dependent-time-lag relay
-
differential relay
-
digital radio relay
-
digital relay
-
direct-action relay
-
directional impedance relay
-
directional power relay
-
directional relay
-
directional-overcurrent relay
-
discriminating relay
-
distance relay
-
double-acting relay
-
draw-out relay
-
dry-feed relay
-
earth-fault relay
-
earthing relay
-
electrical relay
-
electrodynamic relay
-
electromagnetic relay
-
electromechanical relay
-
electronic relay
-
electron relay
-
electrostatic relay
-
element relay
-
enclosed relay
-
entrance relay
-
erase relay
-
excitation-loss relay
-
fast-operating relay
-
fast-release relay
-
ferrodynamic relay
-
ferromagnetic relay
-
field relay
-
field-application relay
-
field-failure relay
-
field-removal relay
-
frequency relay
-
frequency-selective relay
-
gas-actuated relay
-
gas relay
-
gas-filled relay
-
graded time-lag relay
-
grounding relay
-
ground relay
-
guard relay
-
hermetically sealed relay
-
high-speed relay
-
hinged-armature relay
-
holding relay
-
horn relay
-
hot-wire relay
-
impedance relay
-
independent time-lag relay
-
indicating relay
-
indirect-action relay
-
individual point relay
-
induction relay
-
inertia relay
-
initiating relay
-
instantaneous overcurrent relay
-
instantaneous relay
-
interlock relay
-
intermediate switching-off relay
-
interposing relay
-
inverse-time relay
-
keying relay
-
key relay
-
lagged relay
-
lag relay
-
latched relay
-
latch-in relay
-
latching relay
-
leakage relay
-
leak relay
-
LED-coupled solid-state relay
-
light relay
-
light-out relay
-
line relay
-
line-break relay
-
load relay
-
local-remote relay
-
locking relay
-
lock-up relay
-
low-voltage relay
-
low-voltage release relay
-
magnetic relay
-
magnetoelectric relay
-
main locomotive relay
-
main starting relay
-
maximum power relay
-
maximum-voltage relay
-
measuring relay
-
memory relay
-
mercury relay
-
mercury-contact relay
-
mercury-wetted-contact relay
-
metering relay
-
mho relay
-
microprocessor controlled relay for overcurrent protection
-
microwave radio relay
-
microwave relay
-
monostable relay
-
moving-iron relay
-
multiposition relay
-
negative phase-sequence relay
-
net-to-net relay
-
network master relay
-
network-phasing relay
-
neutral relay
-
no-load relay
-
nondirectional relay
-
nonpolarized relay
-
nonspecified-time relay
-
normally closed relay
-
normally open relay
-
notching relay
-
no-voltage relay
-
ohm relay
-
open-frame relay
-
open relay
-
open-phase relay
-
open-track-circuit relay
-
out-of-step relay
-
overcurrent relay
-
overload relay
-
overpower relay
-
overtemperature relay
-
overvoltage relay
-
percentage-differential relay
-
phase relay
-
phase-balance relay
-
phase-comparison relay
-
phase-failure relay
-
phase-reversal relay
-
phase-rotation relay
-
photocell relay
-
photoemissive relay
-
phototube relay
-
plunger relay
-
pneumatic amplifier relay
-
pneumatic relay
-
pneumatic time-delay relay
-
point detection relay
-
point operating relay
-
polarity-directional relay
-
polarized relay
-
positive phase-sequence relay
-
potential relay
-
power direction relay
-
power relay
-
power-transfer relay
-
pressure relay
-
primary relay
-
product relay
-
protection relay
-
pulse relay
-
pulse track relay
-
quick-operating relay
-
quotient relay
-
radio relay
-
rate-of-change relay
-
ratio-balance relay
-
reactance relay
-
reactive power relay
-
reclosing relay
-
reed relay
-
register relay
-
regulating relay
-
reply and call relay
-
reset relay
-
residual relay
-
resistance relay
-
reverse-current relay
-
reverse-phase relay
-
rinding relay
-
route relay
-
route-release relay
-
satellite relay
-
secondary relay
-
sector-type relay
-
selector relay
-
self-resetting relay
-
semiconductor relay
-
service restoring relay
-
shaded-pole relay
-
short-circuit relay
-
shunt relay
-
side-stable relay
-
signal selector relay
-
signaling relay
-
slave relay
-
slew relay
-
slow-acting relay
-
slow-release relay
-
solenoid relay
-
solid-state relay
-
speed relay
-
starting relay
-
static relay with output contact
-
static relay without output contact
-
static relay
-
step-back relay
-
stepping-type relay
-
stepping relay
-
storage relay
-
supervisory relay
-
switch control relay
-
switch indication relay
-
switch lock relay
-
switch position relay
-
switching relay
-
synchronizing relay
-
temperature relay
-
three-position relay
-
time relay
-
time-delay relay
-
timing relay
-
track indicating relay
-
track relay
-
trailing relay
-
train control relay
-
train-stop relay
-
transfer relay
-
transistor relay
-
trip-free relay
-
tuned relay
-
two-element selector relay
-
two-position relay
-
undercurrent relay
-
undervoltage relay
-
unenclosed relay
-
voltage-response relay
-
warning signal relay
-
wet-reed relay
-
wire-break relay
-
zero phase-sequence relay -
8 electrode
1) электрод
2) электродный
– accelerating electrode
– amalgam electrode
– building-up electrode
– coat electrode
– consumable electrode
– contact electrode
– continuous electrode
– control electrode
– cored electrode
– corona-forming electrode
– covered electrode
– current-carrying electrode
– decelerating electrode
– deflecting electrode
– drain electrode
– electrode capacitance
– electrode force
– electrode freezing
– electrode lead
– electrode mast
– electrode metal
– electrode spacing
– electrode suspension
– electrode voltage
– emitter electrode
– emitting electrode
– flux-cored electrode
– fuel electrode
– gate electrode
– graphite electrode
– graphitized electrode
– grounding electrode
– hollow electrode
– ignitor electrode
– implant electrode
– keep-alive electrode
– liquid electrode
– match-strike electrode
– mercury electrode
– nonconsumable electrode
– offset electrode
– pilot electrode
– porous electrode
– reference electrode
– reversible electrode
– roller electrode
– self-baking electrode
– sheathed electrode
– shielding electrode
– source electrode
– starting electrode
– stick electrode
– strip electrode
– tubular electrode
rammed self-baking electrode — набивной самоспекающийся электрод
rise of potential at electrode — возрастание потенциала на электрод
-
9 point
1) пункт
2) запятая
3) кегль
4) острие
5) острый конец
6) очко
7) расшивать
8) расшить
9) точечный
10) шпицевать
11) деление
12) <topogr.> мыс
13) точка
14) место
15) указывать
16) ставить знаки препинания
17) заострение
18) наконечник
19) предмет
20) <engin.> балл
– accessible point
– accumulation point
– adherent point
– altimetric point
– ambiguous point
– amplitude of a point
– anchoring point
– antipodal point
– at a point
– at point
– attaching point
– attachment point
– automatic set point
– barometrical point
– base point
– bending point
– binary point
– boiling point
– boundary point
– branch point
– branching point
– breaker point
– brilliant point
– burble point
– cardinal point
– center point
– check point
– chisel point
– compass-card point
– condensation point
– conjugate point
– contact point
– continuous at a point
– contraction to point
– convergence point
– corner point
– cultivator point
– Curie point
– cuspidal point
– cut point
– cutter point
– data point
– datum point
– dead point
– decimal point
– degree of point
– departure point
– dew point
– diacritical point
– diamond point
– diramation point
– discontinuity point
– divider point
– dividing point
– double point
– drill point
– east point
– enclose a point
– entry point
– equilibrium point
– equivalence point
– evaporating point
– extra-axis point
– extreme point
– finishing point
– firing point
– fix point in position
– fixed point
– flash point
– flex point
– floating point
– form point
– freezing point
– fusion point
– generic point
– glass-transition point
– glaziers' point
– gold point
– grid point
– half-power point
– hinge point
– ice formation point
– ideal point
– ignition point
– image of a point
– indication point
– infinite point
– inflection point
– initial point
– intersection point
– inverse point
– isolated point
– junction point
– labile point
– lattice point
– limit point
– linkage point
– load point
– lubrication point
– main point
– mark a point
– marker point
– mass point
– material point
– measuring point
– melting point
– mirror point
– movable point
– multiple point
– nadir point
– Neel point
– neutral point
– nodal point
– north point
– null point
– operating point
– pitch point
– point approximation
– point at infinity
– point bar
– point brilliance
– point cathode
– point conic
– point contact
– point contacts
– point corrosion
– point diode
– point disturbance
– point eikonal
– point focus
– point force
– point harmonic
– point hologram
– point in time
– point joints
– point lock
– point locking
– point mass
– point of application
– point of break
– point of connection
– point of contact
– point of control
– point of departure
– point of destination
– point of emanation
– point of inflection
– point of interpolation
– point of intersection
– point of junction
– point of lattice
– point of levelling
– point of observation
– point of osculation
– point of reference
– point of separation
– point of sight
– point of support
– point of tangency
– point of the compass
– point of tooth
– point of view
– point pile
– point radiator
– point resolution
– point scale
– point scatterer
– point set
– point source
– point spectrum
– point temperature
– point tool
– point wire
– position of a point
– power of a point
– precipitation point
– principal point
– radix point
– rail point
– ramification point
– reefing point
– reference point
– regular point
– ridge point
– saddle point
– sampling point
– saturation point
– sense point
– separation point
– sequence point
– share point
– silver point
– singing point
– singular point
– softening point
– solidification point
– spark-plug point
– spinodal point
– spiral point
– sputter point
– stagnation point
– starting point
– stationary point
– stock point
– switching point
– terminal point
– tooth point
– touch-down point
– transfer point
– transformation point
– transition point
– triangulation point
– triple point
– turning point
– umbilical point
– unit point
– up to this point
– valley point
– vanishing point
– work point
– world point
– yield point
– zenith point
azimuth of distant point — <topogr.> азимут направления на отдаленную наблюдаемую
bisecting point of a segment — <geom.> середина отрезка
control point adjustment — настройка точки регулирования, <engin.> задатчик
facing point lock — < railways> замок ригельный оконечный
fixed point computation — вычисление с фиксированной запятой
floating decimal point — <comput.> точка плавающая
including the point at infinity — включая бесконечно удаленную точку
phase separation point — <phys.> критическая точка расслаивания
point spread function — <opt.> функция аппаратная, <opt.> функция рассеяния точки
true boiling point — <phys.> температура кипения истинная
-
10 point
1) точка2) балл, очко3) деление (шкалы); румб; лимб4) заострение, остриё, острый конец || заострять, затачивать5) полигр. пункт ( единица измерения в типографской системе мер)6) пост, пункт, место7) мыс8) наконечник9) предмет11) указывать•about a point — мат. в окрестности точки
point at infinity — мат. несобственный элемент, бесконечно удалённая точка
point covers a line — т. граф. вершина покрывает ребро
point in infinity — мат. точка в бесконечности
winding number of curve with respect to point — мат. порядок кривой относительно точки (число оборотов вектора, соединяющего данную точку с точкой кривой при обходе кривой)
right two points — мор. на два румба вправо
with a point as a center — мат. с центром в точке…
- bisecting point of a segment - conditionally stable point - division point - essentially singular point - general point - generic point - horizontal control point - infinitely remote point point - material point - minimal fixed point - negatively stable point - nonessential singular point - optimum point - piercing point of a line - point of greatest concentration - positively normal point - positively stable point - right singular point - single mass point - strongly recurrent point - strongly singular point - triply rational point - uniplanar double point - unstable nodal point - upper significance pointwith respect to point — мат. относительно точки
-
11 resting
1. a отдыхающий; спящий2. a бот. находящийся в покое, спящийresting bud — спящая почка; спящий глазок
Синонимический ряд:1. at rest (adj.) at rest; inactive; inert; not moving; relaxed; undisturbed2. lounging around (adj.) drifting; idling; leisurely; lethargic; loafing; lounging around3. breathing (verb) breathing; laying off; lying by; spelling4. founding (verb) basing; bottoming; building; establishing; founding; grounding; predicating; root in; seating; staying5. lying (verb) consisting; dwelling; existing; inhering; lie down; lying; lying down; reclining; reposing; residing; stretch out; stretching out6. relaxing (verb) relaxing; resting up; unbending; unwinding -
12 défaut à la terre
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
Франко-русский словарь нормативно-технической терминологии > défaut à la terre
-
13 Erdschluβ
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Erdschluβ
-
14 Fehler gegen Erde
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Fehler gegen Erde
-
15 ground connection
- замыкание на землю
- заземление (металлургия)
- заземление (амер.)
- вывод для подсоединения заземляющего проводника
вывод для подсоединения заземляющего проводника
—
[Интент]Тематики
- электротехника, основные понятия
EN
заземление (амер.)
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
заземление
В дуговой сварке, устройство, используемое для присоединения рабочего свинцового кабеля (кабель заземления) к заготовке.
[ http://www.manual-steel.ru/eng-a.html]Тематики
EN
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
Англо-русский словарь нормативно-технической терминологии > ground connection
-
16 ground
- основание (сооружения)
- опускать на землю
- обосновывать
- молотый
- мн. осадок
- масса (в однопроводной электрической цепи)
- замыкание на землю
- заземлить
- грунтовать
- грунт
грунт
1. горные породы, являющиеся объектом инженерно - строительной деятельности человека
2. подготовительный слой материала на поверхности конструкции, являющийся основанием для окрасочных составов
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
грунт
Любая горная порода, залегающая преимущественно в пределах зоны выветривания и являющаяся объектом инженерно-строительной деятельности человека
[ ГОСТ Р 50544-93]Тематики
EN
DE
- 1. Boden
- 1. Grund
- 1.Baugrund
- 2. Grundierung
FR
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
масса (в однопроводной электрической цепи)
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва]Тематики
- электротехника, основные понятия
EN
мн. осадок
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
молотый
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
обосновывать
(напр. решение)
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
основание (сооружения)
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
3.1.2 заземлить (ground): Соединить электрически с землей.
Источник: ГОСТ Р 54274-2010: Топлива авиационные. Определение загрязнений в виде частиц методом лабораторного фильтрования оригинал документа
Англо-русский словарь нормативно-технической терминологии > ground
-
17 earth connection
- замыкание на корпус
- замыкание на землю
- заземление (устройство)
- заземление (англ.)
заземление (англ.)
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
заземление (устройство)
заземляющий провод
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]Тематики
Синонимы
EN
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
замыкание на корпус
Электрическое соединение токоведущей части с открытой проводящей частью.
[ ГОСТ Р 50669-94]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > earth connection
-
18 earth fault
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
замыкание на корпус
Электрическое соединение токоведущей части с открытой проводящей частью.
[ ГОСТ Р 50669-94]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > earth fault
-
19 ground fault (US)
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
Англо-русский словарь нормативно-технической терминологии > ground fault (US)
-
20 ground short circuit
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
Англо-русский словарь нормативно-технической терминологии > ground short circuit
- 1
- 2
См. также в других словарях:
Earth potential rise — In electrical engineering, Earth Potential Rise (EPR) also called Ground Potential Rise (GPR) occurs when a large current flows to earth through an earth grid impedance. The potential relative to a distant point on the Earth is highest at the… … Wikipedia
High Voltage Isolation and Ground Potential Rise — This article outlines the principles of High Voltage Isolation (HVI) and Ground Potential Rise (GPR). Most often questions of concern arise to anyone associated with the use of any communication signal (analog or digital) via a metallic or fiber… … Wikipedia
Ground (electricity) — In electrical engineering, ground or earth may be the reference point in an electrical circuit from which other voltages are measured, or a common return path for electric current, or a direct physical connection to the Earth. A typical earthing… … Wikipedia
Lightning rod — A lightning rod (USA) or lightning conductor (UK) is a single component in a lightning protection system. In addition to rods placed at regular intervals on the highest portions of a structure, a lightning protection system typically includes a… … Wikipedia
Electrical wiring (United States) — Electrical wiring in general refers to conductors used to carry electricity and their accessories. General aspects of electrical wiring as used to provide power in or to buildings and structures, commonly referred to as building wiring, are… … Wikipedia
Lightning protection system — A lightning protection system is a system that protects a structure from damage due to lightning strikes, either through safely conducting the strike to the ground, or preventing the structure from being struck. Most lightning protection systems… … Wikipedia
AC power plugs and sockets — See also: Industrial and multiphase power plugs and sockets Plugs and sockets may sometimes combine male and female contacts, but t … Wikipedia
Earth Sciences — ▪ 2009 Introduction Geology and Geochemistry The theme of the 33rd International Geological Congress, which was held in Norway in August 2008, was “Earth System Science: Foundation for Sustainable Development.” It was attended by nearly… … Universalium
Ground and neutral — For uses of the term ground or earth in electricity but not in the context of mains wiring, see ground (electricity). Since the neutral point of an electrical supply system is often connected to earth ground, ground and neutral are closely… … Wikipedia
History of feminism — The history of feminism is the history of feminist movements and their efforts to overturn injustices of gender inequality. Feminist scholars have divided feminism s history into three waves . Humm, Maggie. 1995. The Dictionary of Feminist Theory … Wikipedia
Ground loop (electricity) — In an electrical system, a ground loop usually refers to a current, generally unwanted, in a conductor connecting two points that are supposed to be at the same potential, often ground, but are actually at different potentials. Ground loops… … Wikipedia