-
1 tension de rétablissement
- восстанавливающееся напряжение (для контактора и пускателя)
- восстанавливающееся напряжение
- восстанавливающееся и возвращающееся напряжение
восстанавливающееся и возвращающееся напряжение
Напряжение, появляющееся на выводах полюса коммутационного аппарата или плавкого предохранителя после отключения тока..
Примечания
1 Напряжение можно рассматривать на протяжении двух последовательных интервалов времени, на первом из которых напряжение переходное, а на последующем — промышленной частоты.
2 Определение действительно для однополюсного аппарата. Для многополюсного аппарата — это межфазное напряжение на входных выводах аппаратов.
МЭК 60050(441-17-25)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
recovery voltage
the voltage which appears across the terminals of a pole of a switching device or a fuse after the breaking of the current
NOTE – This voltage may be considered in two successive intervals of time, one during which a transient voltage exists, followed by a second one during which the power frequency or the steady-state recovery voltage alone exists.
[IEV number 441-17-25]FR
tension de rétablissement
tension qui apparaît entre les bornes d'un appareil de connexion ou d'un fusible après l'interruption du courant
NOTE – Cette tension peut être considérée durant deux intervalles de temps consécutifs, l'un durant lequel existe une tension transitoire, suivi par un second intervalle durant lequel la tension de rétablissement à fréquence industrielle ou en régime établi existe seule.
[IEV number 441-17-25]Тематики
- электротехника, основные понятия
EN
DE
FR
восстанавливающееся напряжение
Напряжение, появляющееся на выводах полюса автоматического выключателя после отключения тока.
Примечания
1 Это напряжение можно рассматривать на протяжении двух последовательных интервалов времени, на первом из которых напряжение переходное, а на последующем втором — напряжение промышленной частоты.
2 Это определение действительно для однополюсного выключателя. Для многополюсного выключателя — это напряжение между входными выводами аппарата
(МЭС 441-17-25)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
восстанавливающееся напряжение
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]EN
recovery voltage
the voltage which appears across the terminals of a pole of a switching device or a fuse after the breaking of the current
NOTE – This voltage may be considered in two successive intervals of time, one during which a transient voltage exists, followed by a second one during which the power frequency or the steady-state recovery voltage alone exists.
[IEV number 441-17-25]FR
tension de rétablissement
tension qui apparaît entre les bornes d'un appareil de connexion ou d'un fusible après l'interruption du courant
NOTE – Cette tension peut être considérée durant deux intervalles de temps consécutifs, l'un durant lequel existe une tension transitoire, suivi par un second intervalle durant lequel la tension de rétablissement à fréquence industrielle ou en régime établi existe seule
[IEV number 441-17-25]Тематики
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
EN
- cleaning voltage
- recovery voltage
- restoring voltage
- restriking voltage
- transient recovery voltage
- TRV
DE
FR
восстанавливающееся напряжение
Напряжение, появляющееся на выводах полюса автоматического выключателя после отключения тока.
Примечания
1 Это напряжение можно рассматривать на протяжении двух последовательных интервалов времени, на первом из которых напряжение переходное, а на последующем втором — напряжение промышленной частоты.
2 Это определение действительно для однополюсного выключателя. Для многополюсного выключателя — это напряжение между входными выводами аппарата
3 У вакуумного контактора или пускателя наибольшее восстанавливающееся напряжение возможно не на первом отключаемом полюсе
(МЭС 441-17-25)
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]EN
recovery voltage
the voltage which appears across the terminals of a pole of a switching device or a fuse after the breaking of the current
NOTE – This voltage may be considered in two successive intervals of time, one during which a transient voltage exists, followed by a second one during which the power frequency or the steady-state recovery voltage alone exists.
[IEV number 441-17-25]FR
tension de rétablissement
tension qui apparaît entre les bornes d'un appareil de connexion ou d'un fusible après l'interruption du courant
NOTE – Cette tension peut être considérée durant deux intervalles de temps consécutifs, l'un durant lequel existe une tension transitoire, suivi par un second intervalle durant lequel la tension de rétablissement à fréquence industrielle ou en régime établi existe seule
[IEV number 441-17-25]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension de rétablissement
-
2 protection par limitation du courant permanent et de la charge électrique, f
защита ограничением установившегося тока и электрического разряда
Защита от поражения электрическим током при помощи такого исполнения электрической цепи или оборудования, которое при нормальных условиях и условиях повреждений ограничивает установившийся ток и электрический разряд до неопасного уровня.
[ ГОСТ Р МЭК 60050-826-2009]EN
protection by limitation of steady-state current and electric charge
protection against electric shock by electric circuit or equipment design so that under normal and fault conditions the steady-state current and electric charge are limited to below a hazardous level
[IEV number 826-12-34]FR
protection par limitation du courant permanent et de la charge électrique, f
protection contre les chocs électriques assurée par la conception des circuits ou des matériels (électriques), de telle façon que le courant permanent et la charge électrique soient limités au-dessous d'une valeur dangereuse, dans les conditions normales ou de défaut
[IEV number 826-12-34]Тематики
EN
DE
- Schutz durch Begrenzung des Beharrungsstroms und der Entladungsenergie, m
FR
- protection par limitation du courant permanent et de la charge électrique, f
Франко-русский словарь нормативно-технической терминологии > protection par limitation du courant permanent et de la charge électrique, f
-
3 courant d'appel
пусковой ток
-EN
inrush current
transient current associated with energizing of transformers, cables, reactors, etc
[IEV number 448-11-30]
inrush current
Iin
current occurring during the transient period from the moment of switching to the steady-state condition
[IEC 60738-1, ed. 3.0 (2006-04)]
starting current
the steady-state r.m.s. current taken from the line over the starting period from zero speed to load speed with rated voltage and frequency applied
[IEV number 411-48-18]FR
courant d'appel
courant transitoire associé à la mise sous tension des transformateurs, câbles, bobines d'inductance, etc
[IEV number 448-11-30]
courant de démarrage
valeur efficace du courant en régime établi, absorbé par le moteur pendant la période de démarrage de la vitesse nulle jusqu'à la vitesse de charge minimale lorsqu'il est alimenté à la tension et à la fréquence assignées
[IEV number 411-48-18]Тематики
- машины электрические вращающиеся в целом
- электротехника, основные понятия
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant d'appel
-
4 courant de démarrage
пусковой ток
-EN
inrush current
transient current associated with energizing of transformers, cables, reactors, etc
[IEV number 448-11-30]
inrush current
Iin
current occurring during the transient period from the moment of switching to the steady-state condition
[IEC 60738-1, ed. 3.0 (2006-04)]
starting current
the steady-state r.m.s. current taken from the line over the starting period from zero speed to load speed with rated voltage and frequency applied
[IEV number 411-48-18]FR
courant d'appel
courant transitoire associé à la mise sous tension des transformateurs, câbles, bobines d'inductance, etc
[IEV number 448-11-30]
courant de démarrage
valeur efficace du courant en régime établi, absorbé par le moteur pendant la période de démarrage de la vitesse nulle jusqu'à la vitesse de charge minimale lorsqu'il est alimenté à la tension et à la fréquence assignées
[IEV number 411-48-18]Тематики
- машины электрические вращающиеся в целом
- электротехника, основные понятия
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant de démarrage
-
5 tension de rétablissement en courant continu en régime établi
установившееся возвращающееся напряжение постоянного тока
Напряжение в цепи постоянного тока после исчезновения переходных явлений, выраженное средним значением при наличии пульсации.
МЭК 60050(441-17-28).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
d.c. steady-state recovery voltage
the recovery voltage in a d.c. circuit after the transient voltage phenomena have subsided, expressed by the mean value where ripple is present
[IEV number 441-17-28]FR
tension de rétablissement en courant continu en régime établi
tension de rétablissement dans un circuit à courant continu après la disparition des phénomènes transitoires de tension, exprimée par sa valeur moyenne s'il y a des ondulations
[IEV number 441-17-28]EN
- d.c. steady-state recovery voltage
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension de rétablissement en courant continu en régime établi
-
6 bruit continu
устойчивый звук
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
steady noise
Unceasing prolonged noise, without interruption. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > bruit continu
-
7 contraction isotonique
Raccourcissement d'un muscle sans modification notable de sa tension.Contraction in which muscles exert a steady pull and get much shorter.Dictionnaire Français-Anglais (UEFA Football) > contraction isotonique
-
8 travail continu
Entraînement de l'endurance caractérisé par un temps de travail dont la durée est supérieure à 30 min. avec une intensité inférieure à l'intensité maximale.Steady exercise at a medium intensity with no bursts of activity or rest periods.Syn. continuous methodDictionnaire Français-Anglais (UEFA Football) > travail continu
-
9 mouvement stable
движение устойчивое
Движение, параметры которого не изменяются во времени
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
устойчивое движение
Невозмущенное движение механической системы, для которого всякое достаточно близкое к нему в начальный момент времени возмущенное движение остается сколь угодно близким во все последующее время.
[Сборник рекомендуемых терминов. Выпуск 102. Теоретическая механика. Академия наук СССР. Комитет научно-технической терминологии. 1984 г.]Тематики
Обобщающие термины
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > mouvement stable
-
10 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
11 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
12 source à courant limité
источник с ограничением тока
Источник электрической энергии для электрической цепи с ограничением возможного значения тока до безопасного уровня, имеющий электрическое разделение между своим выходом и опасными токоведущими частями.
[ ГОСТ Р МЭК 60050-195-2005]
источник с ограничением тока
Устройство, питающее электрическую цепь электрической энергией, которое при этом:
- обеспечивает ток установившегося (постоянного) значения и электрический разряд, ограниченный до неопасного уровня, и
- оборудовано электрическим защитным разделением между выходом устройства и любой опасной токоведущей частью.
[ ГОСТ Р МЭК 60050-826-2009]EN
limited-current source
device supplying electric energy to an electric circuit:
– with a steady-state current and an electric charge limited to non-hazardous levels, and
– equipped with electrically protective separation between the output of the device and any hazardous-live-part
[IEV number 195-06-20]FR
source à courant limité
appareil qui fournit de l'énergie électrique à un circuit électrique:
– avec un courant et une charge en régime permanent limités à des niveaux non dangereux et
– avec une séparation de protection électrique entre la sortie de l'appareil et les parties actives dangereuses
[IEV number 195-06-20]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > source à courant limité
-
13 facteur de régime cyclique
коэффициент циклической токовой нагрузки (кабелей)
Коэффициент, на который может быть умножен номинальный ток установившегося режима, соответствующий коэффициенту нагрузки 100 %, для получения допустимого пикового значения тока в течение суточного цикла, при котором температура токопроводящей жилы в течение этого цикла достигает, но не превышает максимально допустимое значение
[IEV number 461-23-02]EN
cyclic rating factor
factor by which the permissible steady-state rated current corresponding to a 100 % load factor may be multiplied to obtain the permissible peak value of current during a daily cycle such that the conductor attains, but does not exceed, the maximum rated temperature during the cycle
[IEV number 461-23-02]FR
facteur de régime cyclique
facteur par lequel le courant assigné admissible en régime permanent, correspondant à un facteur de charge 100 %, peut être multiplié pour obtenir la valeur de pointe du courant au cours d'un cycle journalier, de sorte qu'au cours de ce cycle, l'âme atteigne sans la dépasser la température assignée maximale
[IEV number 461-23-02]Тематики
- кабели, провода...
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > facteur de régime cyclique
-
14 pression maximale constante limite
максимальное длительное предельное давление
Наибольшее давление газа длительностью более 300 мс (100 мс для новорожденных), создающееся в отверстии для присоединения пациента, когда любое устройство для ограничения давления действует нормально вне зависимости от нормальной работы других частей аппарата.
Обозначение
PLSmax
[ ГОСТ Р 52423-2005]Тематики
- ингаляц. анестезия, искусств. вентиляц. легких
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > pression maximale constante limite
-
15 pression minimale constante limite
минимальное длительное предельное давление
Самое низкое (наиболее отрицательное) давление газа, которое может длиться в отверстии для присоединения пациента более 300 мс (100 мс для новорожденных), когда любое устройство для ограничения давления работает нормально, вне зависимости от нормальной работы других частей аппарата.
Обозначение
PLSmin
[ ГОСТ Р 52423-2005]Тематики
- ингаляц. анестезия, искусств. вентиляц. легких
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > pression minimale constante limite
-
16 élément chauffant lumineux
нагревательный элемент с видимым свечением
Нагревательный элемент, который виден снаружи прибора частично или полностью и температура которого по меньшей мере 650 оС после достижения прибором установившегося состояния при номинальной потребляемой мощности в условиях нормальной работы.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
visibly glowing heating element
heating element that is partly or completely visible from the outside of the appliance and has a temperature of at least 650 °C when the appliance has been operated under normal operation at rated power input until steady conditions have been established
[IEC 60335-1, ed. 4.0 (2001-05)]FR
élément chauffant lumineux
élément chauffant qui est partiellement ou complètement visible de l'extérieur de l'appareil et ayant une température au moins égale à 650 °C après que l'appareil a été mis en fonctionnement dans les conditions de fonctionnement normal à la puissance assignée jusqu'à l'établissement des conditions de régime
[IEC 60335-1, ed. 4.0 (2001-05)]Тематики
Обобщающие термины
EN
FR
Франко-русский словарь нормативно-технической терминологии > élément chauffant lumineux
-
17 charge continue
нагрузка сплошная
Нагрузка, точки приложения которой непрерывно заполняют данный отрезок или данную площадку
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
[Сборник рекомендуемых терминов. Выпуск 82. Строительная механика. Академия наук СССР. Комитет научно-технической терминологии. 1970 г.]Тематики
- строительная механика, сопротивление материалов
EN
DE
FR
постоянное загрязнение
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
continuous load
The amount or quantity of polluting material found in a transporting agent that flows at a steady rate, in contrast to a sudden or dramatic influx. (Source: APD)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > charge continue
-
18 fluage stabilisé
установившаяся ползучесть
Ползучесть, скорость которой постоянна при постоянном напряжении.
[Сборник рекомендуемых терминов. Выпуск 82. Строительная механика. Академия наук СССР. Комитет научно-технической терминологии. 1970 г.]
ползучесть установившаяся
Ползучесть, протекающая при постоянных во времени напряжениях
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- строительная механика, сопротивление материалов
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > fluage stabilisé
-
19 service ininterrompu
продолжительный режим
Режим при котором главные контакты автоматического выключателя остаются замкнутыми, непрерывно проводя установившийся ток в течение длительного времени (неделями, месяцами или даже годами).
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
uninterrupted duty
duty in which the main contacts of a circuit-breaker remain closed whilst carrying a steady current without interruption for long periods (which could be weeks, months, or even years)
[IEC 60898-1, ed. 1.0 (2002-01)]FR
service ininterrompu
service dans lequel les contacts principaux d'un disjoncteur restent fermés tout en transportant un courant régulier sans interruption pendant de longues périodes (qui peuvent être des semaines, des mois, et même des années)
[IEC 60898-1, ed. 1.0 (2002-01)]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > service ininterrompu
-
20 service ininterrompu (pour un dispositif de coupure)
непрерывный режим
длительный режим
-
[IEV number 442-05-43]EN
uninterrupted duty (for a switching device)
duty in which the main contacts of a switching device remain closed whilst carrying a steady current without interruption for long periods (which could be weeks, months, or even years)
[IEV number 442-05-43]FR
service ininterrompu (pour un dispositif de coupure)
service dans lequel les contacts principaux d'un dispositif de coupure restent fermés tout en transportant un courant permanent sans interruption pendant de longues périodes (qui peuvent être des semaines, des mois, et même des années)
[IEV number 442-05-43]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > service ininterrompu (pour un dispositif de coupure)
- 1
- 2
См. также в других словарях:
steady — adj Steady, uniform, even, equable, constant are comparable when they mean neither markedly varying nor variable but much the same throughout its course or extent. Steady is the most widely applicable of these terms; in general it suggests… … New Dictionary of Synonyms
Steady, As She Goes — «Steady, As She Goes» … Википедия
steady — [sted′ē] adj. steadier, steadiest [ STEAD + Y2] 1. that does not shake, tremble, totter, etc.; firm; fixed; stable 2. constant, regular, uniform, or continuous; not changing, wavering, or faltering [a steady gaze, a steady diet, a steady rhythm]… … English World dictionary
Steady state (disambiguation) — Steady state in general is a dynamic equilibrium commonly observed in dynamic systems. Specifically, it may refer to: *Steady state (biochemistry), a central term in osmosis *Steady state (chemistry), a central term in chemical kinetics *Steady… … Wikipedia
Steady — Stead y ( [y^]), a. [Compar. {Steadier} ( [i^]*[ e]r); superl. {Steadiest}.] [Cf. AS. stedig sterile, barren, st[ae][eth][eth]ig, steady (in gest[ae][eth][eth]ig), D. stedig, stadig, steeg, G. st[ a]tig, stetig. See {Stead}, n.] 1. Firm in… … The Collaborative International Dictionary of English
Steady rest — Steady Stead y ( [y^]), a. [Compar. {Steadier} ( [i^]*[ e]r); superl. {Steadiest}.] [Cf. AS. stedig sterile, barren, st[ae][eth][eth]ig, steady (in gest[ae][eth][eth]ig), D. stedig, stadig, steeg, G. st[ a]tig, stetig. See {Stead}, n.] 1. Firm in … The Collaborative International Dictionary of English
Steady state — is a more general situation than dynamic equilibrium. If a system is in steady state, then the recently observed behavior of the system will continue into the future. In stochastic systems, the probabilities that various different states will be… … Wikipedia
Steady B — (bürgerlich Warren McGlone, * 5. Januar 1970 in Philadelphia) ist ein amerikanischer Rapper und Musikproduzent. Er gehörte zur Rap Gruppe Hilltop Hustlers aus Philadelphia. Inhaltsverzeichnis 1 Leben 2 Diskografie 3 Weblinks … Deutsch Wikipedia
Steady-state free precession imaging — Steady state free precession (SSFP) imaging is a magnetic resonance imaging (MRI) technique which uses steady states of magnetizations. In general, SSFP MRI sequences are based on a (low flip angle) gradient echo MRI sequence with a short… … Wikipedia
steady on — british spoken phrase used for telling someone that you do not approve of the bad things that they are saying Steady on, Karen! You’re talking about my boyfriend. Thesaurus: ways of emphasizing when you are annoyed or angrysynonym Main entry:… … Useful english dictionary
steady your nerves — phrase to stop yourself from feeling nervous She took a deep breath to steady her nerves. Thesaurus: to be, or to become calm and stop worryingsynonym Main entry: steady * * * steady your nerves : to make yourself calm or calmer … Useful english dictionary