-
1 интергармоническая частота
интергармоническая частота
Любая частота, не кратная основной частоте.По аналогии с порядком кратности гармоник порядок интергармонической частоты основан на отношении к основной частоте. Если это отношение меньше единицы, то такую гармоническую частоту называют субгармонической. В соответствии с рекомендацией МЭК порядок интергармонических частот обозначается буквой «m»
EN
interharmonic frequency
frequency which is a non-integer multiple of the reference fundamental frequency
NOTE 1 By extension of the harmonic order, the interharmonic order is the ratio of interharmonic frequency to the reference fundamental frequency, this ratio is not an integer (recommended notation " m ").
NOTE 2 In the case where " m 1" the term of sub-harmonic frequency may also be used (see IEV 551-20-10).
[IEC 60146-1-1, ed. 4.0 (2009-06)]FR
fréquence interharmonique
fréquence qui est un multiple non entier de la fréquence fondamentale de référence
NOTE 1 Par extension du rang harmonique, le rang interharmonique désigne le rapport de la fréquence interharmonique à la fréquence fondamentale de référence. Ce rapport n’est pas un entier (notation recommandée « m »).
NOTE 2 Lorsque « m < 1 », le terme de fréquence sous-harmonique peut également être employé (voir VEI 551-20-10).
[IEC 60146-1-1, ed. 4.0 (2009-06)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > интергармоническая частота
-
2 частота гармоники
частота гармоники
Частота, кратная основной частоте.
Примечание. Отношение частоты гармоники к основной частоте называют "порядком гармоники".
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
harmonic frequency
frequency which is an integer multiple of the fundamental frequency
NOTE The ratio of the harmonic frequency to the fundamental frequency is the harmonic order (notation: h).
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
fréquence harmonique
fréquence qui est un multiple entier de la fréquence fondamentale
NOTE Le rapport entre la fréquence harmonique et la fréquence fondamentale est le rang harmonique (notation: h).
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > частота гармоники
-
3 коэффициент подавления общего вида
коэффициент подавления общего вида
-
[IEV number 312-06-21]EN
common mode rejection ratio
CMRR (abbreviation)
ratio of the voltage applied between a specified reference point and the input terminals, when connected together by a specified circuit, to the voltage required between the input terminals to produce the same value of the output
NOTE 1 – The common mode rejection ratio is usually expressed in decibels and can depend on the frequency, the waveform and the method of measurement.
NOTE 2 – Common mode rejection ratio can also apply to quantities other than voltage.
[IEV number 312-06-21]FR
rapport de réjection de mode commun
rapport de la tension appliquée entre un point de référence spécifié et les deux bornes d'entrée connectées l'une à l'autre par un circuit spécifié, à la tension nécessaire entre les bornes d'entrée pour produire la même valeur de sortie
NOTE 1 – Le facteur de réjection de mode commun est généralement exprimé en décibels et peut dépendre de la fréquence, de la forme d’onde et de la méthode de mesure.
NOTE 2 – Le rapport de réjection de mode commun peut aussi s'appliquer à des grandeurs autres que les tensions.
[IEV number 312-06-21]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > коэффициент подавления общего вида
-
4 коэффициент подавления при последовательном включении
коэффициент подавления при последовательном включении
-
[IEV number 312-06-22]EN
series mode rejection ratio
SMRR (abbreviation)
ratio of the series mode voltage causing a specified change in output information, to the voltage initiated by the measurand which would produce the same change
NOTE 1 – The series mode rejection ratio is usually expressed in decibels and may depend on the frequency, the waveform and the method of measurement.
NOTE 2 – Series mode rejection ratio can also apply to quantities other than voltage.
[IEV number 312-06-22]FR
rapport de réjection de mode série
rapport de la tension de mode série, provoquant un changement spécifié d'information de sortie, à la tension résultant du mesurande qui produirait le même changement
NOTE 1 – Le facteur de réjection de mode série est généralement exprimé en décibels et peut dépendre de la fréquence, de la forme d’onde et de la méthode de mesure.
NOTE 2 – Le rapport de réjection de mode commun peut aussi s'appliquer à des grandeurs autres que les tensions.
[IEV number 312-06-22]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > коэффициент подавления при последовательном включении
-
5 добротность
добротность
1. Количественная характеристика потерь колебательной системы при резонансе, равная
где Wк - полный запас энергии колебаний при резонансе;
Wп - потери энергии за период
[ Физический энциклопедический словарь]
2. Количественная мера потерь колебательной системы. Показывает, во сколько раз амплитуда вынужденных колебаний при резонансе превышает амплитуду на частоте, много меньшей резонансной при одинаковой внешней силе
3. Отношение резонансной частоты спектра колебаний к его ширине на уровне 0,707 от максимального значения амплитуды спектра
Примечание
Определения 2 и 3 являются достаточно точными для систем с высокой добротностью (Q >(5-10)), определение 1 пригодно во всех случаях
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
добротность (1)
коэффициент добротности (1)
-
[IEV number 151-15-45]
добротность (2)
коэффициент добротности (2)
-
[IEV number 151-15-46]EN
quality factor (1)
Q factor (1)
for a capacitor or inductor under periodic conditions, ratio of the absolute value of the reactive power to the active power
NOTE 1 – The quality factor is a measure of the losses, usually unwanted, in a capacitor or an inductor.
NOTE 2 – The quality factor depends generally on frequency and voltage.
[IEV number 151-15-45]
quality factor (2)
Q factor (2)
for a resonant circuit at the resonance frequency, 2π times the ratio of the maximum stored energy to the energy dissipated during one period
NOTE – The quality factor is a measure of sharpness of the resonance.
Source: 801-24-12 MOD
[IEV number 151-15-46]FR
facteur de qualité (1), m
facteur de surtension (1), m
pour un condensateur ou une bobine d'inductance en régime périodique, rapport de la valeur absolue de la puissance réactive à la puissance active
NOTE 1 – Le facteur de qualité caractérise les pertes, généralement non désirées, dans un condensateur ou une bobine d'inductance.
NOTE 2 – Le facteur de qualité dépend généralement de la fréquence et de la tension.
[IEV number 151-15-45]
facteur de qualité (2), m
facteur de surtension (2), m
pour un circuit résonant fonctionnant à la fréquence de résonance, 2π fois le rapport de l'énergie maximale emmagasinée dans le circuit à l'énergie dissipée pendant une période
NOTE – Le facteur de qualité caractérise l'acuité de la résonance.
Source: 801-24-12 MOD
[IEV number 151-15-46]Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > добротность
-
6 коэффициент замыкания на землю
коэффициент замыкания на землю
Отношение наибольшего фазного напряжения в месте металлического замыкания на землю к напряжению в той же точке при отсутствии замыкания.
[ ГОСТ 24291-90]
коэффициент замыкания на землю
Для данного места трехфазной системы заданной конфигурации отношение максимального значения фазного напряжения промышленной частоты на исправном линейном проводнике во время замыкания на землю одного или нескольких линейных проводников в какой-либо точке системы к значению напряжения промышленной частоты в данном месте при отсутствии какого-либо замыкания на землю.
[ ГОСТ Р МЭК 60050-195-2005]
коэффициент замыкания на землю
Отношение напряжения на неповрежденной фазе в рассматриваемой точке трехфазной электрической сети (обычно в точке установки электрооборудования) при замыкании на землю одной или двух других фаз к фазному напряжению рабочей частоты, которое установилось бы в данной точке при устранении замыкания.
Примечание. При определении коэффициента замыкания на землю место замыкания и состояние схемы электрической сети выбираются такими, которые дают наибольшее значение коэффициента
[ ГОСТ 1516.1-76]
коэффициент замыкания на землю
Коэффициент, определяющий отношение влияния на одну или более фаз в любой точке сети во время замыкания на землю другой исправной фазы при наивысшем значении ее напряжения в заданном месте при заданном местоположении трехфазной сети и для заданной конфигурации соответственно в отсутствие любого подобного замыкания. [IEV 604-03-06]
[ ГОСТ Р МЭК 60044-7-2010]EN
earth fault factor
at a given location of a three-phase system, and for a given system configuration, ratio of the highest root-mean-square value of line-to-earth power frequency voltage on a healthy line conductor during an earth fault affecting one or more line conductors at any point on the system, to the root-mean-square value of line-to-earth power frequency voltage which would be obtained at the given location in the absence of any such earth fault
Source: 604-03-06 MOD
[IEV number 195-05-14]FR
facteur de court-circuit à la terre
en un emplacement donné d'un réseau triphasé, et pour un schéma d'exploitation donné de ce réseau, rapport entre d'une part la tension efficace la plus élevée, à la fréquence du réseau, entre un conducteur de ligne saine et la terre pendant un défaut à la terre affectant un ou plusieurs conducteurs de ligne en un point quelconque du réseau, et d'autre part la valeur efficace de la tension phase-terre à la fréquence du réseau qui serait obtenue à l'emplacement considéré en l'absence d'un tel défaut à la terre
Source: 604-03-06 MOD
[IEV number 195-05-14]Тематики
EN
DE
FR
82 коэффициент замыкания на землю
Отношение наибольшего фазного напряжения в месте металлического замыкания на землю к напряжению в той же точке при отсутствии замыкания
604-03-06*
de Erdfehlerfactor
en earth fault factor
fr facteur de défaut à la terre
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > коэффициент замыкания на землю
-
7 полное сопротивление относительно земли
полное сопротивление относительно земли
Полное сопротивление (импеданс) между точкой системы или установки, или оборудования и относительной землей на данной частоте.
[ ГОСТ Р МЭК 60050-195-2005]
полное сопротивление относительно земли
Полное сопротивление между определенной точкой системы или установки, или оборудования и эталонной землей на данной частоте.
[ ГОСТ Р МЭК 60050-826-2009]EN
impedance to earth
impedance at a given frequency between a specified point in a system or in an installation or in equipment and reference earth
[IEV number 195-01-17]
impedance to earth
impedance to ground (US)
impedance at a given frequency between a specified point in a system or in an installation or in equipment and reference earth
NOTE 1 – Reference earth is defined in IEC 60050-195. In practice, a reference point can be substituted to earth, for example the chassis.
NOTE 2 – The common mode rejection ratio of an instrument is dependent on the impedances between the input terminals and earth. Each of these impedances is called a common mode impedance.
Source: 195-01-17
[IEV number 312-06-20]FR
impédance de mise à la terre
impédance à une fréquence donnée entre un point spécifié d'un réseau, d'une installation ou d'un matériel et la terre de référence
[IEV number 195-01-17]
impédance de mise à la terre
impédance à une fréquence donnée entre un point spécifié d'un réseau, d'une installation ou d'un matériel et la terre de référence
NOTE 1 – La terre de référence est définie dans la CEI 60050-195. En pratique, on peut lui substituer un point de référence, par exemple la masse.
NOTE 2 – Le facteur de réjection de mode commun d'un appareil dépend de l'impédance entre chacune des bornes d'entrée et la terre. Chacune de ces impédances est appelée impédance de mode commun.
Source: 195-01-17
[IEV number 312-06-20]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > полное сопротивление относительно земли
-
8 асинхронная машина
асинхронная машина
Бесколлекторная машина переменного тока, у которой отношение частоты вращения ротора к частоте тока в цепи, подключенной к машине, зависит от нагрузок.
[ ГОСТ 27471-87]EN
asynchronous machine
an alternating current machine in which the speed on load and the frequency of the system to which it is connected are not in a constant ratio
[IEV ref 411-31-09]FR
machine asynchrone
machine à courant alternatif dont la vitesse en charge et la fréquence du réseau auquel elle est reliée ne sont pas dans un rapport constant
[IEV ref 411-31-09]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > асинхронная машина
См. также в других словарях:
Frequency Scanning Interferometry — (FSI) is an absolute distance measurement technique, for measuring the distance between a pair of points, along a line of sight. The power of the FSI technique lies in its ability to make many such distance measurements, simultaneously. For each… … Wikipedia
frequency — [frē′kwənsfrē′kwən sē] n. pl. frequencies [ME < Fr < L frequentia < frequens: see FREQUENT] 1. Obs. a) the condition of being crowded b) a crowd 2. the fact of occurring often or repeatedly; frequent occurrence 3 … English World dictionary
Frequency modulation — See also: Amplitude modulation In telecommunications, frequency modulation (FM) conveys information over a carrier wave by varying its frequency (contrast this with amplitude modulation, in which the amplitude of the carrier is varied while its… … Wikipedia
Frequency synthesizer — A frequency synthesizer is an electronic system for generating any of a range of frequencies from a single fixed timebase or oscillator. They are found in many modern devices, including radio receivers, mobile telephones, radiotelephones, walkie… … Wikipedia
Frequency modulation synthesis — In audio and music frequency modulation synthesis (or FM synthesis) is a form of audio synthesis where the timbre of a simple waveform is changed by frequency modulating it with a modulating frequency that is also in the audio range, resulting in … Wikipedia
Frequency list — In computational linguistics, a frequency list is a sorted list of words (word types) together with their frequency, where frequency here usually means the number of occurrences in a given corpus. A short example could be: the3789654he 2098762 [ … Wikipedia
frequency — n. (pl. ies) 1 commonness of occurrence. 2 a the state of being frequent; frequent occurrence. b the process of being repeated at short intervals. 3 Physics the rate of recurrence of a vibration, oscillation, cycle, etc.; the number of… … Useful english dictionary
Ratio distribution — A ratio distribution (or quotient distribution ) is a statistical distribution constructed as the distribution of the ratio of random variables having two other distributions.Given two stochastic variables X and Y , the distribution of the… … Wikipedia
Frequency distribution — In statistics, a frequency distribution is an arrangement of the values that one or more variables take in a sample. Each entry in the table contains the frequency or count of the occurrences of values within a particular group or interval, and… … Wikipedia
Frequency (statistics) — In statistics the frequency of an event i is the number ni of times the event occurred in the experiment or the study. These frequencies are often graphically represented in histograms. We speak of absolute frequencies, when the counts ni… … Wikipedia
Frequency probability — Statistical probability redirects here. For the episode of Star Trek: Deep Space Nine, see Statistical Probabilities. John Venn Frequency probability is the interpretation of probability that defines an event s probability as the limit of its… … Wikipedia