-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
2 возобновляемый сырьевой материал
возобновляемый сырьевой материал
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
renewable raw material
Resources that have a natural rate of availability and yield a continual flow of services which may be consumed in any time period without endangering future consumption possibilities as long as current use does not exceed net renewal during the period under consideration. (Source: WHIT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > возобновляемый сырьевой материал
-
3 пластмасса
пластмасса
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
plastic
A polymeric material (usually organic) of large molecular weight which can be shaped by flow; usually refers to the final product with fillers, plasticizers, pigments, and stabilizers included (versus the resin, the homogeneous polymeric starting material); examples are polyvinyl chloride, polyethylene, and urea-formaldehyde. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > пластмасса
-
4 труба для сброса отходов
труба для сброса отходов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
exhaust device
1) A duct or pipe through which waste material is emitted.
2) A combination of components which provides for enclosed flow of exhaust gas from engine parts to the atmosphere.
(Source: AMHER / LEE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > труба для сброса отходов
См. также в других словарях:
Material flow accounting — (MFA) is the study of material flows on a national or regional scale. It is therefore sometimes also referred to as regional, national or economy wide material flow analysis. Contents 1 Definition 2 Terms and Indicators 3 References 4 … Wikipedia
Material derivative — The material derivative[1][2] is a derivative taken along a path moving with velocity v, and is often used in fluid mechanics and classical mechanics. It describes the time rate of change of some quantity (such as heat or momentum) by following… … Wikipedia
flow chart — A chart used to provide a model for the flow of material, information, or people through a system. The primary purpose of a flow chart is to identify the activities taking place within a system and to enable this information to be presented… … Big dictionary of business and management
Material flow management — (MFM) is a method of efficiently managing materials. Material flow management is the goal oriented, efficient use of materials, material streams and energy. The goals are given by ecological and economical areas and by observing social aspects.… … Wikipedia
Material flow — (MF) is the description of the transportation of raw materials, pre fabricates, parts, components, integrated objects and finally products as a flow of entities. The term applies mainly to advanced modeling of Supply chain management. As… … Wikipedia
Flow measurement — is the quantification of bulk fluid movement. Flow can be measured in a variety of ways. Positive displacement flow meters acumulate a fixed volume of fluid and then count the number of times the volume is filled to measure flow. Other flow… … Wikipedia
Flow — may refer to:In science and technology: *Dataflow, computing term related to the flow of messages between software components *Environmental flow, the amount of water necessary in a watercourse to maintain a healthy ecosystem *Flow (computer… … Wikipedia
Flow stress — is defined as the instantaneous value of stress required to continue deforming the material to keep the metal flowing. It is the Yield Strength of the metal as a function of strain, which can be expressed: [1] Yf = Ke^nYf = Flow stress, MPaK =… … Wikipedia
Material flow analysis — 3R Concepts Waste Disposal Hierarchy Reduce Reuse Recycle Barter Dematerialization Downcycling Dumpster diving Ecode … Wikipedia
Material Point Method — The Material Point Method (MPM), is an extension of the Particle in cell (PIC) Method in computational fluid dynamics to computational solid dynamics, and is a Finite element method (FEM) based particle method. It is primarily used for multiphase … Wikipedia
Flow battery — A flow battery is a form of rechargeable battery in which electrolyte containing one or more dissolved electroactive species flows through a power cell / reactor that converts chemical energy to electricity. Additional electrolyte is stored… … Wikipedia