-
1 Failure Analysis and Control System
Quality control: FACSУниверсальный русско-английский словарь > Failure Analysis and Control System
-
2 failure and usage data report
Quality control: FUDRУниверсальный русско-английский словарь > failure and usage data report
-
3 failure assessment diagram
Quality control: FADУниверсальный русско-английский словарь > failure assessment diagram
-
4 failure mode cause analysis
Quality control: FMCAУниверсальный русско-английский словарь > failure mode cause analysis
-
5 failure mode frequency ratio
Quality control: FMFRУниверсальный русско-английский словарь > failure mode frequency ratio
-
6 failure modes and effect analysis
Quality control: FMEAУниверсальный русско-английский словарь > failure modes and effect analysis
-
7 failure, unsatisfactory or removal
Quality control: FURУниверсальный русско-английский словарь > failure, unsatisfactory or removal
-
8 failure-rate data
Quality control: FARADA -
9 failure recurrence control
Engineering: FRCУниверсальный русско-английский словарь > failure recurrence control
-
10 total loss control
Gen Mgtthe implementation of safety procedures to prevent or limit the impact of a complete or partial loss of an organization’s physical assets. Total loss control is based on safety audit and prevention techniques. It is concerned with reduction or elimination of losses caused by accidents and occupational ill health. The extent to which it is implemented is usually decided by calculating the total organizational asset cost and weighing this against the likelihood of failure and its worst possible effects on the organization. Total loss control was developed in the 1960s as an approach to risk management. -
11 Cause of Failure, Effect and Corrective
Универсальный русско-английский словарь > Cause of Failure, Effect and Corrective
-
12 acceptance failure rate
Quality control: AFRУниверсальный русско-английский словарь > acceptance failure rate
-
13 airborne equipment failure
Quality control: AEFУниверсальный русско-английский словарь > airborne equipment failure
-
14 catastrophic failure rate
Quality control: CFRУниверсальный русско-английский словарь > catastrophic failure rate
-
15 cumulative failure rate
Quality control: CFRУниверсальный русско-английский словарь > cumulative failure rate
-
16 decreasing failure rate average
Quality control: DFRAУниверсальный русско-английский словарь > decreasing failure rate average
-
17 degradation failure rate
Quality control: DFRУниверсальный русско-английский словарь > degradation failure rate
-
18 early failure
Quality control: EF -
19 hazard of failure
Quality control: HF -
20 human-initiated failure
Quality control: HIFУниверсальный русско-английский словарь > human-initiated failure
См. также в других словарях:
Failure rate — is the frequency with which an engineered system or component fails, expressed for example in failures per hour. It is often denoted by the Greek letter λ (lambda) and is important in reliability engineering. The failure rate of a system usually… … Wikipedia
Control chart — One of the Seven Basic Tools of Quality First described by Walter A. Shewhart … Wikipedia
Control reconfiguration — is an active approach in control theory to achieve fault tolerant control for dynamic systems [1]. It is used when severe faults, such as actuator or sensor outages, cause a break up of the control loop, which must be restructured to prevent… … Wikipedia
Control reversal — is an adverse effect on the controllability of aircraft. The flight controls reverse themselves in a way that is not intuitive, so pilots may not be aware of the situation and therefore provide the wrong inputs; in order to roll to the left, for… … Wikipedia
Control (House) — Control House episode Episode no. Season 1 Episode 14 Directed by Randy Zisk Written by … Wikipedia
Control (Pedro the Lion album) — Control Studio album by Pedro the Lion Released April 16, 2002 … Wikipedia
Failure mode and effects analysis — A failure modes and effects analysis (FMEA) is a procedure for analysis of potential failure modes within a system for classification by severity or determination of the effect of failures on the system. It is widely used in manufacturing… … Wikipedia
Control (management) — Controlling is one of the managerial functions like planning, organizing, staffing and directing. It is an important function because it helps to check the errors and to take the corrective action so that deviation from standards are minimized… … Wikipedia
Control rod — PWR control rod assembly, above fuel element A control rod is a rod made of chemical elements capable of absorbing many neutrons without fissioning themselves. They are used in nuclear reactors to control the rate of fission of uranium and… … Wikipedia
Control of the National Grid — The National Grid is the high voltage electric power transmission network in Great Britain, connecting power stations and major substations, and has a synchronized organization such that electricity generated anywhere in Great Britain can be used … Wikipedia
Control of the National Grid (UK) — The National Grid (UK) is the high voltage electric power transmission network in Great Britain, connecting power stations and major substations to ensure that electricity generated anywhere in Great Britain can be used to satisfy demand… … Wikipedia