-
21 Gleichzeitigkeitsfaktor
коэффициент одновременности
Отношение совмещенного максимума нагрузки энергоустановок потребителей к сумме максимумов нагрузки этих же установок за тот же интервал времени.
[ ГОСТ 19431-84]Параллельные тексты EN-RU
... have a breaking capacity sufficient to interrupt the current of the largest motor when stalled together with the sum of the normal running currents of all other motors and/or loads.
The calculated breaking capacity may be reduced by the use of a proven diversity factor.
[IEC 60204-1-2006]... иметь отключающую способность, достаточную для отключения тока при заторможенном роторе самого мощного двигателя, плюс сумму токов всех других работающих в нормальном режиме двигателей и/или других нагрузок данной цепи.
Вычисленную таким образом отключающую способность можно уменьшить за счет применения обоснованного коэффициента одновременности.
[Перевод Интент]Тематики
EN
DE
59. Коэффициент одновременности
D. Gleichzeitigkeitsfaktor
Отношение совмещенного максимума нагрузки энергоустановок потребителей к сумме максимумов нагрузки этих же установок за тот же интервал времени
Источник: ГОСТ 19431-84: Энергетика и электрификация. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Gleichzeitigkeitsfaktor
-
22 Bemessungsfaktor für zyklische Last
коэффициент циклической токовой нагрузки (кабелей)
Коэффициент, на который может быть умножен номинальный ток установившегося режима, соответствующий коэффициенту нагрузки 100 %, для получения допустимого пикового значения тока в течение суточного цикла, при котором температура токопроводящей жилы в течение этого цикла достигает, но не превышает максимально допустимое значение
[IEV number 461-23-02]EN
cyclic rating factor
factor by which the permissible steady-state rated current corresponding to a 100 % load factor may be multiplied to obtain the permissible peak value of current during a daily cycle such that the conductor attains, but does not exceed, the maximum rated temperature during the cycle
[IEV number 461-23-02]FR
facteur de régime cyclique
facteur par lequel le courant assigné admissible en régime permanent, correspondant à un facteur de charge 100 %, peut être multiplié pour obtenir la valeur de pointe du courant au cours d'un cycle journalier, de sorte qu'au cours de ce cycle, l'âme atteigne sans la dépasser la température assignée maximale
[IEV number 461-23-02]Тематики
- кабели, провода...
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Bemessungsfaktor für zyklische Last
-
23 Dimension einer Grösse
размерность физической величины
размерность величины
Выражение в форме степенного одночлена, составленного из произведений символов основных физических величин в различных степенях и отражающее связь данной физической величины с физическими величинами, принятыми в данной системе величин за основные с коэффициентом пропорциональности, равным 1.
Примечания
1. Степени символов основных величин, входящих в одночлен, в зависимости от связи рассматриваемой физической величины с основными, могут быть целыми, дробными, положительными и отрицательными. Понятие размерность распространяется и на основные величины. Размерность основной величины в отношении самой себя равна единице, т.е. формула размерности основной величины совпадает с ее символом.
2. В соответствии с международным стандартом ИСО 31/0, размерность величин следует обозначать знаком dim [2]. В системе величин LMT размерность величины.x будет: dim х = LlMmTt, где L, М, Т - символы, величин, принятых за основные (соответственно длины, массы, времени).
[РМГ 29-99]EN
dimension of a quantity
quantity dimension
dimension
expression of the dependence of a quantity on the base quantities of a system of quantities as a product of powers of factors corresponding to the base quantities, omitting any numerical factor
NOTE 1 – A power of a factor is the factor raised to an exponent. Each factor is the dimension of a base quantity.
NOTE 2 – The conventional symbolic representation of the dimension of a base quantity is a single upper case letter in roman (upright) sans-serif type. The conventional symbolic representation of the dimension of a derived quantity is the product of powers of the dimensions of the base quantities according to the definition of the derived quantity. The dimension of a quantity Q is denoted by dim Q.
NOTE 3 – In deriving the dimension of a quantity, no account is taken of its scalar, vector or tensor character.
NOTE 4 – In a given system of quantities, – quantities of the same kind have the same dimension, – quantities of different dimensions are always of different kinds, and – quantities having the same dimension are not necessarily of the same kind. For example, in the ISQ, pressure and energy density (volumic energy) have the same dimension L–1MT–2. See also note 5.
NOTE 5 – In the International System of Quantities (ISQ), the symbols representing the dimensions of the base quantities are:
[IEV number 112-01-11]FR
dimension, f
dimension d'une grandeur, f
expression de la dépendance d’une grandeur par rapport aux grandeurs de base d'un système de grandeurs sous la forme d'un produit de puissances de facteurs correspondant aux grandeurs de base, en omettant tout facteur numérique
NOTE 1 – Une puissance d'un facteur est le facteur muni d'un exposant. Chaque facteur exprime la dimension d'une grandeur de base.
NOTE 2 – Par convention, la représentation symbolique de la dimension d'une grandeur de base est une lettre majuscule unique en caractère romain (droit) sans empattement. Par convention, la représentation symbolique de la dimension d'une grandeur dérivée est le produit de puissances des dimensions des grandeurs de base conformément à la définition de la grandeur dérivée. La dimension de la grandeur Q est notée dim Q.
NOTE 3 – Pour établir la dimension d'une grandeur, on ne tient pas compte du caractère scalaire, vectoriel ou tensoriel.
NOTE 4 – Dans un système de grandeurs donné, – les grandeurs de même nature ont la même dimension, – des grandeurs de dimensions différentes sont toujours de nature différente, – des grandeurs ayant la même dimension ne sont pas nécessairement de même nature. Par exemple, dans l'ISQ, la pression et l'énergie volumique ont la même dimension L–1MT–2. Voir aussi la note 5.
NOTE 5 – Dans le Système international de grandeurs (ISQ), les symboles représentant les dimensions des grandeurs de base sont:
[IEV number 112-01-11]Тематики
- метрология, основные понятия
Синонимы
EN
DE
- Dimension einer Grösse
- Dimension, f
- Größendimension, f
FR
- dimension d'une grandeur, f
- dimension, f
Немецко-русский словарь нормативно-технической терминологии > Dimension einer Grösse
-
24 Dimension, f
размерность физической величины
размерность величины
Выражение в форме степенного одночлена, составленного из произведений символов основных физических величин в различных степенях и отражающее связь данной физической величины с физическими величинами, принятыми в данной системе величин за основные с коэффициентом пропорциональности, равным 1.
Примечания
1. Степени символов основных величин, входящих в одночлен, в зависимости от связи рассматриваемой физической величины с основными, могут быть целыми, дробными, положительными и отрицательными. Понятие размерность распространяется и на основные величины. Размерность основной величины в отношении самой себя равна единице, т.е. формула размерности основной величины совпадает с ее символом.
2. В соответствии с международным стандартом ИСО 31/0, размерность величин следует обозначать знаком dim [2]. В системе величин LMT размерность величины.x будет: dim х = LlMmTt, где L, М, Т - символы, величин, принятых за основные (соответственно длины, массы, времени).
[РМГ 29-99]EN
dimension of a quantity
quantity dimension
dimension
expression of the dependence of a quantity on the base quantities of a system of quantities as a product of powers of factors corresponding to the base quantities, omitting any numerical factor
NOTE 1 – A power of a factor is the factor raised to an exponent. Each factor is the dimension of a base quantity.
NOTE 2 – The conventional symbolic representation of the dimension of a base quantity is a single upper case letter in roman (upright) sans-serif type. The conventional symbolic representation of the dimension of a derived quantity is the product of powers of the dimensions of the base quantities according to the definition of the derived quantity. The dimension of a quantity Q is denoted by dim Q.
NOTE 3 – In deriving the dimension of a quantity, no account is taken of its scalar, vector or tensor character.
NOTE 4 – In a given system of quantities, – quantities of the same kind have the same dimension, – quantities of different dimensions are always of different kinds, and – quantities having the same dimension are not necessarily of the same kind. For example, in the ISQ, pressure and energy density (volumic energy) have the same dimension L–1MT–2. See also note 5.
NOTE 5 – In the International System of Quantities (ISQ), the symbols representing the dimensions of the base quantities are:
[IEV number 112-01-11]FR
dimension, f
dimension d'une grandeur, f
expression de la dépendance d’une grandeur par rapport aux grandeurs de base d'un système de grandeurs sous la forme d'un produit de puissances de facteurs correspondant aux grandeurs de base, en omettant tout facteur numérique
NOTE 1 – Une puissance d'un facteur est le facteur muni d'un exposant. Chaque facteur exprime la dimension d'une grandeur de base.
NOTE 2 – Par convention, la représentation symbolique de la dimension d'une grandeur de base est une lettre majuscule unique en caractère romain (droit) sans empattement. Par convention, la représentation symbolique de la dimension d'une grandeur dérivée est le produit de puissances des dimensions des grandeurs de base conformément à la définition de la grandeur dérivée. La dimension de la grandeur Q est notée dim Q.
NOTE 3 – Pour établir la dimension d'une grandeur, on ne tient pas compte du caractère scalaire, vectoriel ou tensoriel.
NOTE 4 – Dans un système de grandeurs donné, – les grandeurs de même nature ont la même dimension, – des grandeurs de dimensions différentes sont toujours de nature différente, – des grandeurs ayant la même dimension ne sont pas nécessairement de même nature. Par exemple, dans l'ISQ, la pression et l'énergie volumique ont la même dimension L–1MT–2. Voir aussi la note 5.
NOTE 5 – Dans le Système international de grandeurs (ISQ), les symboles représentant les dimensions des grandeurs de base sont:
[IEV number 112-01-11]Тематики
- метрология, основные понятия
Синонимы
EN
DE
- Dimension einer Grösse
- Dimension, f
- Größendimension, f
FR
- dimension d'une grandeur, f
- dimension, f
Немецко-русский словарь нормативно-технической терминологии > Dimension, f
-
25 Größendimension, f
размерность физической величины
размерность величины
Выражение в форме степенного одночлена, составленного из произведений символов основных физических величин в различных степенях и отражающее связь данной физической величины с физическими величинами, принятыми в данной системе величин за основные с коэффициентом пропорциональности, равным 1.
Примечания
1. Степени символов основных величин, входящих в одночлен, в зависимости от связи рассматриваемой физической величины с основными, могут быть целыми, дробными, положительными и отрицательными. Понятие размерность распространяется и на основные величины. Размерность основной величины в отношении самой себя равна единице, т.е. формула размерности основной величины совпадает с ее символом.
2. В соответствии с международным стандартом ИСО 31/0, размерность величин следует обозначать знаком dim [2]. В системе величин LMT размерность величины.x будет: dim х = LlMmTt, где L, М, Т - символы, величин, принятых за основные (соответственно длины, массы, времени).
[РМГ 29-99]EN
dimension of a quantity
quantity dimension
dimension
expression of the dependence of a quantity on the base quantities of a system of quantities as a product of powers of factors corresponding to the base quantities, omitting any numerical factor
NOTE 1 – A power of a factor is the factor raised to an exponent. Each factor is the dimension of a base quantity.
NOTE 2 – The conventional symbolic representation of the dimension of a base quantity is a single upper case letter in roman (upright) sans-serif type. The conventional symbolic representation of the dimension of a derived quantity is the product of powers of the dimensions of the base quantities according to the definition of the derived quantity. The dimension of a quantity Q is denoted by dim Q.
NOTE 3 – In deriving the dimension of a quantity, no account is taken of its scalar, vector or tensor character.
NOTE 4 – In a given system of quantities, – quantities of the same kind have the same dimension, – quantities of different dimensions are always of different kinds, and – quantities having the same dimension are not necessarily of the same kind. For example, in the ISQ, pressure and energy density (volumic energy) have the same dimension L–1MT–2. See also note 5.
NOTE 5 – In the International System of Quantities (ISQ), the symbols representing the dimensions of the base quantities are:
[IEV number 112-01-11]FR
dimension, f
dimension d'une grandeur, f
expression de la dépendance d’une grandeur par rapport aux grandeurs de base d'un système de grandeurs sous la forme d'un produit de puissances de facteurs correspondant aux grandeurs de base, en omettant tout facteur numérique
NOTE 1 – Une puissance d'un facteur est le facteur muni d'un exposant. Chaque facteur exprime la dimension d'une grandeur de base.
NOTE 2 – Par convention, la représentation symbolique de la dimension d'une grandeur de base est une lettre majuscule unique en caractère romain (droit) sans empattement. Par convention, la représentation symbolique de la dimension d'une grandeur dérivée est le produit de puissances des dimensions des grandeurs de base conformément à la définition de la grandeur dérivée. La dimension de la grandeur Q est notée dim Q.
NOTE 3 – Pour établir la dimension d'une grandeur, on ne tient pas compte du caractère scalaire, vectoriel ou tensoriel.
NOTE 4 – Dans un système de grandeurs donné, – les grandeurs de même nature ont la même dimension, – des grandeurs de dimensions différentes sont toujours de nature différente, – des grandeurs ayant la même dimension ne sont pas nécessairement de même nature. Par exemple, dans l'ISQ, la pression et l'énergie volumique ont la même dimension L–1MT–2. Voir aussi la note 5.
NOTE 5 – Dans le Système international de grandeurs (ISQ), les symboles représentant les dimensions des grandeurs de base sont:
[IEV number 112-01-11]Тематики
- метрология, основные понятия
Синонимы
EN
DE
- Dimension einer Grösse
- Dimension, f
- Größendimension, f
FR
- dimension d'une grandeur, f
- dimension, f
Немецко-русский словарь нормативно-технической терминологии > Größendimension, f
-
26 biotischer Faktor
биотический фактор
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biotic factor
The influence upon the environment of organisms owing to the presence and activities of other organisms, as distinct from a physical, abiotic, environmental factor. (Source: ALL2)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > biotischer Faktor
-
27 Einflussfaktor
влияющая (ий) величина фактор электрического реле
Любая (ой) величина (фактор), способная (ый) изменить одну из заданных характеристик электрического реле.
Примечание. Заданными характеристиками являются, например, срабатывание, возврат, точность
[ ГОСТ 16022-83]EN
influencing quantity
any quantity likely to modify any of the specified characteristics of a relay (operating, releasing, accuracy, etc.)
[IEV number 446-14-01]
influencing factor
any factor likely to modify any of the specified characteristics of a relay (operating, releasing, accuracy, etc.)
[IEV number 446-14-02]FR
grandeur d'influence
grandeur susceptible de modifier l'une des caractéristiques spécifiées d'un relais: fonctionnement, relâchement, précision, et
[IEV number 446-14-01]
facteur d'influence
facteur susceptible de modifier l'une des caractéristiques spécifiées d'un relais: fonctionnement, relâchement, précision, etc
[IEV number 446-14-02]Тематики
Классификация
>>>EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Einflussfaktor
-
28 Einflussgrösse
влияющая (ий) величина фактор электрического реле
Любая (ой) величина (фактор), способная (ый) изменить одну из заданных характеристик электрического реле.
Примечание. Заданными характеристиками являются, например, срабатывание, возврат, точность
[ ГОСТ 16022-83]EN
influencing quantity
any quantity likely to modify any of the specified characteristics of a relay (operating, releasing, accuracy, etc.)
[IEV number 446-14-01]
influencing factor
any factor likely to modify any of the specified characteristics of a relay (operating, releasing, accuracy, etc.)
[IEV number 446-14-02]FR
grandeur d'influence
grandeur susceptible de modifier l'une des caractéristiques spécifiées d'un relais: fonctionnement, relâchement, précision, et
[IEV number 446-14-01]
facteur d'influence
facteur susceptible de modifier l'une des caractéristiques spécifiées d'un relais: fonctionnement, relâchement, précision, etc
[IEV number 446-14-02]Тематики
Классификация
>>>EN
DE
FR
влияющая физическая величина
влияющая величина
Физическая величина, оказывающая влияние на размер измеряемой величины и (или) результат измерений.
[РМГ 29-99]Тематики
- метрология, основные понятия
Синонимы
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Einflussgrösse
-
29 Güte
добротность пьезоэлектрического резонатора
Отношение реактивного сопротивления пьезоэлектрического резонатора на частоте последовательного резонанса к его динамическому сопротивлению.
[ ГОСТ 18669-73]Тематики
EN
DE
FR
добротность системы
добротность
Величина, обратная удвоенному относительному демпфированию системы (см. примечание к термину характеристика восстанавливающей силы (момента)).
[ ГОСТ 24346-80]
добротность системы
добротность
Величина, обратная удвоенному относительному демпфированию системы
Примечание
Определение дано для системы с одной степенью свободы.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]Тематики
Синонимы
EN
DE
FR
- facteur d’amplification dynamique, q
Немецко-русский словарь нормативно-технической терминологии > Güte
-
30 Kompensationskondensator
конденсатор для повышения коэффициента мощности
-
[ ГОСТ 1282-88]EN
power factor correction capacitor
a power capacitor connected in parallel with a circuit to improve its power factor
[IEV number 811-27-22]FR
condensateur d'amélioration de facteur de puissance
condensateur de puissance destiné à être connecté en parallèle sur un circuit, pour en améliorer le facteur de puissance
[IEV number 811-27-22]Конструктивно конденсатор представляет собой металлический (стальной или алюминиевый) корпус, в котором размещаются секции (пакеты), намотанные из нескольких слоев алюминиевой фольги, проложенных конденсаторной бумагой или синтетической пленкой толщиной 10—15 мкм (0,01—0,015 мм). Соединенные между собой секции имеют выводы, расположенные снаружи корпуса, в его верхней части. Трехфазные конденсаторы имеют три фарфоровых вывода, однофазные — один.
Конденсатор, как и любой элемент электроэнергетической системы, характеризуется потерями активной мощности, которые приводят к его нагреву. Эти потери тем больше, чем выше приложенное напряжение, его частота и емкость конденсатора. Потери в конденсаторе зависят и от свойств диэлектрика, определяемых тангенсом угла диэлектрических потерь (tg) и характеризующих удельные потери (Вт/квар) в конденсаторе. В зависимости от типа и назначения конденсатора потери в них могут составлять от 0,5 до 4 Вт/квар.
В электроэнергетике для компенсации реактивной мощности применяют так называемые косинусные конденсаторы, предназначенные для работы при частоте напряжения 50 Гц. Их мощность, измеряемая в киловольт-амперах реактивных (квар), составляет от 10 до 100 квар.
Шкала номинальных напряжений конденсаторов от 230 В до 10,5 кВ, что позволяет собирать из них установки для сетей напряжением от 380 В и выше. Конденсаторы обладают хорошей перегрузочной способностью по току (до 30 % от номинального) и по напряжению (до 10 % от номинального).
[ http://www.energocon.com/pages/id1243.html]Тематики
- компенсация реактивной мощности
- конденсаторы для повыш. коэф. мощности
Обобщающие термины
Синонимы
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Kompensationskondensator
-
31 Scheitelfaktor
коэффициент амплитуды кривой переменного напряжения (тока)
Величина, равная отношению максимального по модулю за период значения напряжения (тока) к действующему значению периодического напряжения (тока).
[ ГОСТ 23875-88]
[ОАО РАО "ЕЭС России" СТО 17330282.27.010.001-2008]EN
peak factor
ratio of the maximum absolute value of an alternating quantity to its root-mean-square value
[IEV number 101-14-57]FR
facteur de crête
rapport de la valeur absolue maximale à la valeur efficace d'une grandeur alternative
[IEV number 101-14-57]Тематики
Синонимы
EN
DE
FR
Смотри также
51. Коэффициент амплитуды кривой переменного напряжения (тока)
Коэффициент амплитуды
D. Scheitelfaktor
E. Peak factor
F. Facteur de crête
Величина, равная отношению максимального по модулю за период значения напряжения (тока) к действующему значению периодического напряжения (тока)
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Scheitelfaktor
32 Messbereichsfaktor
коэффициент диапазонов
-
[IEV number 314-09-02]EN
range factor
multiplying factor of the indication produced by a measuring instrument
[IEV number 314-09-02]FR
facteur de calibre
facteur multiplicatif de l'indication fournie par un instrument de mesure
[IEV number 314-09-02]Тематики
- измерение электр. величин в целом
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Messbereichsfaktor
33 Welligkeit (einer Mischspannung oder eines Mischstromes)
- Коэффициент пульсации напряжения (тока) по среднему значению
- коэффициент пульсации напряжения (тока) no среднему значению
коэффициент пульсации напряжения (тока) no среднему значению
Величина, равная отношению среднего значения переменной составляющей пульсирующего напряжения (тока) к его постоянной составляющей.
[ ГОСТ 23875-88]EN
r.m.s.-ripple factor
the ratio of the r.m.s. value of the ripple content to the absolute value of the direct component of a pulsating quantity
Source: MOD 131-03-13
[IEV number 161-02-27]FR
taux d'ondulation efficace
rapport de la valeur efficace de l'ondulation d'une grandeur pulsatoire à la valeur absolue de la composante continue
Source: MOD 131-03-13
[IEV number 161-02-27]Тематики
EN
- r.m.s.-ripple factor
DE
FR
- taux d’ondulation efficace (d’une tension ou d’un courant pulsatoire)
Смотри также
60. Коэффициент пульсации напряжения (тока) по среднему значению
D. Welligkeit (einer Mischspannung oder eines Mischstromes)
E. R. m. s. - ripple factor
F. Taux d’ondulation efficace (d’une tension ou d’un courant pulsatoire)
Величина, равная отношению среднего значения переменной составляющей пульсирующего напряжения (тока) к его постоянной составляющей
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Welligkeit (einer Mischspannung oder eines Mischstromes)
34 Formfaktor
коэффициент формы кривой переменного напряжения (тока)
Величина, равная отношению действующего значения периодического напряжения (тока) к его среднему значению.
[ ГОСТ 23875-88]
[ОАО РАО "ЕЭС России" СТО 17330282.27.010.001-2008]EN
form factor
ratio of the root-mean-square value of an alternating quantity to its rectified value
[IEV number 101-14-56]FR
facteur de forme
rapport de la valeur efficace à la valeur redressée d'une grandeur alternative
[IEV number 101-14-56]Тематики
EN
DE
FR
Смотри также
50. Коэффициент формы кривой переменного напряжения (тока)
D. Formfaktor
E. Form factor
F. Facteur de forme
Величина, равная отношению действующего значения периодического напряжения (тока) к его среднему значению
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Formfaktor
35 Spannungsänderung bei einer bestimmten Belastung
падение или повышение напряжения при заданном режиме нагрузки
Разность между напряжением холостого хода обмотки и напряжением на ее выводах при заданных нагрузке и коэффициенте мощности при условии, что к другой (или к одной из других) обмотке(ок) подведено напряжение, равное:
- номинальному, если трансформатор включен на основное ответвление (в этом случае напряжение холостого хода рассматриваемой обмотки равно номинальному);
- напряжению другого ответвления, на которое включен трансформатор. Падение или повышение напряжения обычно выражают в процентах напряжения холостого хода рассматриваемой обмотки.
Примечание — В многообмоточном трансформаторе падение или повышение напряжения зависит от нагрузки и коэффициента мощности не только данной обмотки, но и других обмоток
(МЭС 421-07-03).
[ ГОСТ 30830-2002]EN
voltage drop or rise for a specified load condition
voltage regulation for a specified load condition
the arithmetic difference between the no-load voltage of a winding and the voltage developed at the terminals of the same winding at a specified load and power factor, the voltage supplied to (one of) the other winding(s) being equal to:
- its rated value if the transformer is connected on the principal tapping (the no-load voltage of the former winding is then equal to its rated value);
- the tapping voltage if the transformer is connected on another tapping.
This difference is generally expressed as a percentage of the no-load voltage of the former winding
NOTE – For multi-winding transformers, the voltage drop or rise depends not only on the load and power factor of the winding itself, but also on the load and power factor of the other windings
[IEV number 421-07-03]FR
hute ou augmentation de tension pour une condition de charge spécifiée
différence arithmétique entre la tension à vide d'un enroulement et la tension en charge aux bornes du même enroulement pour un courant de charge et un facteur de puissance spécifiés, la tension appliquée à l'autre (ou à l'un des autres) enroulement(s) étant égale:
- à sa valeur assignée, si le transformateur est connecté sur la prise principale (la tension à vide du premier enroulement étant alors égale à sa valeur assignée);
- à la tension de prise si le transformateur est connecté sur une autre prise.
Cette différence s'exprime généralement sous la forme d'un pourcentage de la tension à vide du premier enroulement
NOTE – Pour les transformateurs à plus de deux enroulements, la chute ou l'augmentation de tension dépend non seulement de la charge et du facteur de puissance de l'enroulement lui-même, mais aussi de la charge et du facteur de puissance des autres enroulements.
[IEV number 421-07-03]Тематики
Классификация
>>>EN
- voltage drop or rise for a specified load condition
- voltage regulation for a specified load condition
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Spannungsänderung bei einer bestimmten Belastung
36 ökologischer Faktor
экологический фактор
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
ecological factor
An environmental factor that, under some definite conditions, can exert appreciable influence on organisms or their communities, causing the increase or decrease in the number of organisms and/or changes in the communities. (Source: UNUN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > ökologischer Faktor
37 abiotischer Faktor
абиотический фактор
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
abiotic factor
Physical, chemical and other non-living environmental factors. They are essential for living plants and animals of an ecosystem, providing the essential elements and nutrients that are necessary for growth. The abiotic elements also include the climatic and pedologic components of the ecosystem. (Source: LBC / WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > abiotischer Faktor
38 anthropogener Faktor
антропогенный фактор
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
anthropogenic factor
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > anthropogener Faktor
39 Biokonzentrationsfaktor
биоконцентрирующий фактор
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
bioconcentration factor
The quotient of the concentration of a chemical in aquatic organisms at a specific time or during a discrete time period of exposure, divided by the concentration in the surrounding water at the same time or during the same period. (Source: KOREN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Biokonzentrationsfaktor
40 Betriebsspannungsabhängigkeit des Vervielfachungsfaktors der Lawinenphotodiode
вольтовая характеристика коэффициента умножения лавинного фотодиода
Зависимость коэффициента умножения лавинного фотодиода от напряжения, приложенного к нему.
Обозначение
MT(U)
Mф(U)
Md(U)
Mph(U)
[ ГОСТ 21934-83]Тематики
- приемники излуч. полупроводн. и фотоприемн. устр.
EN
DE
- Betriebsspannungsabhängigkeit des Vervielfachungsfaktors der Lawinenphotodiode
161. Вольтовая характеристика коэффициента умножения лавинного фотодиода
D. Betriebsspannungsabhängigkeit des Vervielfachungsfaktors der Lawinenphotodiode
E. Bias multiplication factor characteristic of the avalanche photodiode
MT(U), MФ(U)
Зависимость коэффициента умножения лавинного фотодиода от напряжения, приложенного к нему
Источник: ГОСТ 21934-83: Приемники излучения полупроводниковые фотоэлектрические и фотоприемные устройства. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Betriebsspannungsabhängigkeit des Vervielfachungsfaktors der Lawinenphotodiode
СтраницыСм. также в других словарях:
Factor-X — Saltar a navegación, búsqueda Para el programa de televisión, véase Factor X (TV). Un wikipedista está trabajando actualmente en extender este artículo. Es posible que, a causa de ello, haya lagunas de contenido o deficiencias de formato. Por… … Wikipedia Español
factor — FÁCTOR, factori, s.m. I. 1. Element, condiţie, împrejurare care determină apariţia unui proces, a unei acţiuni, a unui fenomen. 2. (mat.) Fiecare dintre termenii unei înmulţiri. ♢ Factor prim = fiecare dintre numerele prime prin care se împarte… … Dicționar Român
Factor — Paradigmen: multiparadigmatisch Erscheinungsjahr: 2003 Designer: Slava Pestov Aktuelle Version: 0.94 (September 2010) … Deutsch Wikipedia
Factor 5 — Saltar a navegación, búsqueda Factor 5, LLC Tipo Privada Fundación 1987 Sede San Rafael, California, Estados Unidos Administración … Wikipedia Español
factor — aside from its technical senses, means ‘a fact or circumstance that contributes to a result’, and the notion of cause lies at the heart of its use, as in Gladstone s sentence (1878) The first factor in the making of a nation is its religion. A… … Modern English usage
factor — fac·tor n [Medieval Latin, doer, maker, agent, from Latin, maker, from facere to do, make] 1: one who acts or transacts business for another: as a: a commercial agent who buys or sells goods for others on commission b: one that lends money to… … Law dictionary
Factor 5 — LLC war eine deutsche und später US amerikanische Firma, die Computer und Videospiele entwickelte. Sie entstand aus der Hacker Gruppe The Light Circle und wurde 1987 in Köln als kleines Entwicklungsstudio für Computerspiele gegründet. Die 5 im… … Deutsch Wikipedia
Factor — Saltar a navegación, búsqueda Un factor puede hacer referencia a: Factorización; operación matemática. Factorización de enteros Factor (lenguaje de programación) Factor X; grupo de superhéroes mutantes de Marvel Comics. Factor X (programa de… … Wikipedia Español
Factor Rh — Saltar a navegación, búsqueda El Factor Rh es una proteína integral de la membrana aglutinógena que está presente en todas las células. Un 85% de la población tiene en esa proteína una estructura dominante, que corresponde a una determinada… … Wikipedia Español
factor Rh — m. inmun. Factor Rhesus. Medical Dictionary. 2011. factor Rh … Diccionario médico
FACTOR — may also refer to the Object Oriented programming requirements caputre acronym Functionality, Application domain, Conditions, Technology, Objects and Responsibility; FACTOR (the Foundation to Assist Canadian Talent on Records) is a private non… … Wikipedia
Перевод: с немецкого на русский
с русского на немецкий- С русского на:
- Немецкий
- С немецкого на:
- Все языки
- Английский
- Вьетнамский
- Испанский
- Латинский
- Нидерландский
- Русский