-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
2 ток стабилизации стабилитрона
ток стабилизации стабилитрона
Iст
Iz
Значение постоянного тока, протекающего через стабилитрон в режиме стабилизации.
[ ГОСТ 25529-82]Тематики
Обобщающие термины
EN
DE
FR
82. Ток стабилизации стабилитрона
D. Z-Strom der Z-Diode
E. Continuous current within the working voltage range
F. Courant continu inverse pour la gamme des tensions de régulation
Iст
Значение постоянного тока, протекающего через стабилитрон в режиме стабилизации
Источник: ГОСТ 25529-82: Диоды полупроводниковые. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-французский словарь нормативно-технической терминологии > ток стабилизации стабилитрона
См. также в других словарях:
Voltage clamp — The voltage clamp is used by electrophysiologists to measure the ion currents across a neuronal membrane while holding the membrane voltage at a set level. Neuronal membranes contain many different kinds of ion channels, some of which are voltage … Wikipedia
Voltage Mode — Schaltbild eines Gleichstromstellers im Voltage Mode Der Voltage Mode ist eine grundsätzliche Art einen Gleichstromsteller zu regeln. Die Regelung beobachtet, im Gegensatz zum Current Mode lediglich die Ausgangsspannung und wandelt diese… … Deutsch Wikipedia
Current Mode — Signalflussplan und Blockschaltbild eines Abwärtswandlers mit Current Mode Regelung Der Current Mode ist eine grundsätzliche Art, einen Gleichstromsteller oder ein Schaltnetzteil zu regeln. Die Regelung beobachtet im Gegensatz zum Voltage Mode… … Deutsch Wikipedia
Voltage regulator — A popular three pin 12 V DC voltage regulator IC. A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. A voltage regulator may be a simple feed forward design or may include negative feedback … Wikipedia
Current differencing buffered amplifier — Block diagram of the CDBA A current differencing buffered amplifier (CDBA) is a multi terminal active component with two inputs and two outputs and developed by Cevdet Acar and Serdar Özoğuz. Its block diagram can be seen from the figure. It is… … Wikipedia
High voltage — The term high voltage characterizes electrical circuits, in which the voltage used is the cause of particular safety concerns and insulation requirements. High voltage is used in electrical power distribution, in cathode ray tubes, to generate X… … Wikipedia
Alternating current — (green curve). The horizontal axis measures time; the vertical, current or voltage. In alternating current (AC, also ac) the movement of electric charge periodically reverses direction. In direct current (DC, also dc), the flow of electric charge … Wikipedia
High Voltage Protection and Isolation of telecommunications circuits and SCADA circuits to and from Hydro Sub Stations — High Voltage Protection and Isolation of telecommunications circuits and SCADA circuits to and from Hydro Sub StationsIn order to protect the continuous service of important telecommunications and control circuits to and from Hydro Sub Stations,… … Wikipedia
ГОСТ 20332-84: Тиристоры. Термины, определения и буквенные обозначения параметров — Терминология ГОСТ 20332 84: Тиристоры. Термины, определения и буквенные обозначения параметров оригинал документа: 110. Время включения тиристора E. Turn on time F. Temps d’amorcage tувкл, tвкл Интервал времени, в течение которого тиристор… … Словарь-справочник терминов нормативно-технической документации
Electric motor — For other kinds of motors, see motor (disambiguation). For a railroad electric engine, see electric locomotive. Various electric motors. A 9 volt PP3 transistor battery is in the center foreground for size comparison. An electric motor converts… … Wikipedia
DC-to-DC converter — An assortment of 78xx series ICs, linear DC DC converters A DC to DC converter is an electronic circuit which converts a source of direct current (DC) from one voltage level to another. It is a class of power converter. Contents … Wikipedia