Перевод: со всех языков на английский

с английского на все языки

condensing+engine

  • 1 Auspuffdampfmaschine

    f < bahn> ■ non-condensing steam engine; non-condensing engine

    German-english technical dictionary > Auspuffdampfmaschine

  • 2 машина, работающая на выхлоп

    1. non-condensing engine

     

    машина, работающая на выхлоп
    —
    [А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]

    Тематики

    EN

    Русско-английский словарь нормативно-технической терминологии > машина, работающая на выхлоп

  • 3 Watt, James

    [br]
    b. 19 January 1735 Greenock, Renfrewshire, Scotland
    d. 19 August 1819 Handsworth Heath, Birmingham, England
    [br]
    Scottish engineer and inventor of the separate condenser for the steam engine.
    [br]
    The sixth child of James Watt, merchant and general contractor, and Agnes Muirhead, Watt was a weak and sickly child; he was one of only two to survive childhood out of a total of eight, yet, like his father, he was to live to an age of over 80. He was educated at local schools, including Greenock Grammar School where he was an uninspired pupil. At the age of 17 he was sent to live with relatives in Glasgow and then in 1755 to London to become an apprentice to a mathematical instrument maker, John Morgan of Finch Lane, Cornhill. Less than a year later he returned to Greenock and then to Glasgow, where he was appointed mathematical instrument maker to the University and was permitted in 1757 to set up a workshop within the University grounds. In this position he came to know many of the University professors and staff, and it was thus that he became involved in work on the steam engine when in 1764 he was asked to put in working order a defective Newcomen engine model. It did not take Watt long to perceive that the great inefficiency of the Newcomen engine was due to the repeated heating and cooling of the cylinder. His idea was to drive the steam out of the cylinder and to condense it in a separate vessel. The story is told of Watt's flash of inspiration as he was walking across Glasgow Green one Sunday afternoon; the idea formed perfectly in his mind and he became anxious to get back to his workshop to construct the necessary apparatus, but this was the Sabbath and work had to wait until the morrow, so Watt forced himself to wait until the Monday morning.
    Watt designed a condensing engine and was lent money for its development by Joseph Black, the Glasgow University professor who had established the concept of latent heat. In 1768 Watt went into partnership with John Roebuck, who required the steam engine for the drainage of a coal-mine that he was opening up at Bo'ness, West Lothian. In 1769, Watt took out his patent for "A New Invented Method of Lessening the Consumption of Steam and Fuel in Fire Engines". When Roebuck went bankrupt in 1772, Matthew Boulton, proprietor of the Soho Engineering Works near Birmingham, bought Roebuck's share in Watt's patent. Watt had met Boulton four years earlier at the Soho works, where power was obtained at that time by means of a water-wheel and a steam engine to pump the water back up again above the wheel. Watt moved to Birmingham in 1774, and after the patent had been extended by Parliament in 1775 he and Boulton embarked on a highly profitable partnership. While Boulton endeavoured to keep the business supplied with capital, Watt continued to refine his engine, making several improvements over the years; he was also involved frequently in legal proceedings over infringements of his patent.
    In 1794 Watt and Boulton founded the new company of Boulton \& Watt, with a view to their retirement; Watt's son James and Boulton's son Matthew assumed management of the company. Watt retired in 1800, but continued to spend much of his time in the workshop he had set up in the garret of his Heathfield home; principal amongst his work after retirement was the invention of a pantograph sculpturing machine.
    James Watt was hard-working, ingenious and essentially practical, but it is doubtful that he would have succeeded as he did without the business sense of his partner, Matthew Boulton. Watt coined the term "horsepower" for quantifying the output of engines, and the SI unit of power, the watt, is named in his honour.
    [br]
    Principal Honours and Distinctions
    FRS 1785. Honorary LLD, University of Glasgow 1806. Foreign Associate, Académie des Sciences, Paris 1814.
    Further Reading
    H.W.Dickinson and R Jenkins, 1927, James Watt and the Steam Engine, Oxford: Clarendon Press.
    L.T.C.Rolt, 1962, James Watt, London: B.T. Batsford.
    R.Wailes, 1963, James Watt, Instrument Maker (The Great Masters: Engineering Heritage, Vol. 1), London: Institution of Mechanical Engineers.
    IMcN

    Biographical history of technology > Watt, James

  • 4 Todd, Leonard Jennett

    [br]
    fl. 1885 London, England
    [br]
    English (?) patentee of steam engines incorporating the uniflow principle.
    [br]
    In a uniflow system, the steam enters a steam engine cylinder at one end, pushes the pistons along, and exhausts through a ring of ports at the centre of the cylinder that are uncovered by movement of the piston. The piston is returned by steam then entering the other end of the cylinder, moving the piston arrangement back, and again making its exit through the central ports. This gave the thermodynamic advantage of the cylinder ends remaining hot and the centre colder with reheating the ends of the cylinder through compression of the residual steam. The principle was first patented by Jacob Perkins in England in 1827 and was tried in America in 1856.
    Little is known about Todd. The addresses given in his patent specifications show that he was living first at South Hornsey and then Stoke Newington, both in Middlesex (now in London). No obituary notices have been traced. He took out a patent in 1885 for a "terminal exhaust engine" and followed this with two more in 1886 and 1887. His aim was to "produce a double acting steam engine which shall work more efficiently, which shall produce and maintain within itself an improved gradation of temperature extending from each of its two Hot Inlets to its common central Cold Outlet". His later patents show the problems he faced with finding suitable valve gears and the compression developing during the return stroke of the piston. It was this last problem, particularly when starting a condensing engine, that probably defeated him through excessive compression pressures. There is some evidence that he hoped to apply his engines to railway locomotives.
    [br]
    Bibliography
    1885, British patent no. 7,301 (terminal exhaust engine). 1886, British patent no. 2,132.
    1887, British patent no. 6,666.
    Further Reading
    R.L.Hills, 1989, Power from Steam. A History of the Stationary Steam Engine, Cambridge University Press (provides the fullest discussion of his patents). H.W.Dickinson, 1938, A Short History of the Steam Engine, Cambridge University Press.
    J.Stumpf, 1912, The Una-Flow Steam Engine, Munich: R.Oldenbourg.
    RLH

    Biographical history of technology > Todd, Leonard Jennett

  • 5 Murdock (Murdoch), William

    [br]
    b. 21 August 1754 Cumnock, Ayrshire, Scotland
    d. 15 November 1839 Handsworth, Birmingham, England
    [br]
    Scottish engineer and inventor, pioneer in coal-gas production.
    [br]
    He was the third child and the eldest of three boys born to John Murdoch and Anna Bruce. His father, a millwright and joiner, spelled his name Murdock on moving to England. He was educated for some years at Old Cumnock Parish School and in 1777, with his father, he built a "wooden horse", supposed to have been a form of cycle. In 1777 he set out for the Soho manufactory of Boulton \& Watt, where he quickly found employment, Boulton supposedly being impressed by the lad's hat. This was oval and made of wood, and young William had turned it himself on a lathe of his own manufacture. Murdock quickly became Boulton \& Watt's representative in Cornwall, where there was a flourishing demand for steam-engines. He lived at Redruth during this period.
    It is said that a number of the inventions generally ascribed to James Watt are in fact as much due to Murdock as to Watt. Examples are the piston and slide valve and the sun-and-planet gearing. A number of other inventions are attributed to Murdock alone: typical of these is the oscillating cylinder engine which obviated the need for an overhead beam.
    In about 1784 he planned a steam-driven road carriage of which he made a working model. He also planned a high-pressure non-condensing engine. The model carriage was demonstrated before Murdock's friends and travelled at a speed of 6–8 mph (10–13 km/h). Boulton and Watt were both antagonistic to their employees' developing independent inventions, and when in 1786 Murdock set out with his model for the Patent Office, having received no reply to a letter he had sent to Watt, Boulton intercepted him on the open road near Exeter and dissuaded him from going any further.
    In 1785 he married Mary Painter, daughter of a mine captain. She bore him four children, two of whom died in infancy, those surviving eventually joining their father at the Soho Works. Murdock was a great believer in pneumatic power: he had a pneumatic bell-push at Sycamore House, his home near Soho. The pattern-makers lathe at the Soho Works worked for thirty-five years from an air motor. He also conceived the idea of a vacuum piston engine to exhaust a pipe, later developed by the London Pneumatic Despatch Company's railway and the forerunner of the atmospheric railway.
    Another field in which Murdock was a pioneer was the gas industry. In 1791, in Redruth, he was experimenting with different feedstocks in his home-cum-office in Cross Street: of wood, peat and coal, he preferred the last. He designed and built in the backyard of his house a prototype generator, washer, storage and distribution plant, and publicized the efficiency of coal gas as an illuminant by using it to light his own home. In 1794 or 1795 he informed Boulton and Watt of his experimental work and of its success, suggesting that a patent should be applied for. James Watt Junior was now in the firm and was against patenting the idea since they had had so much trouble with previous patents and had been involved in so much litigation. He refused Murdock's request and for a short time Murdock left the firm to go home to his father's mill. Boulton \& Watt soon recognized the loss of a valuable servant and, in a short time, he was again employed at Soho, now as Engineer and Superintendent at the increased salary of £300 per year plus a 1 per cent commission. From this income, he left £14,000 when he died in 1839.
    In 1798 the workshops of Boulton and Watt were permanently lit by gas, starting with the foundry building. The 180 ft (55 m) façade of the Soho works was illuminated by gas for the Peace of Paris in June 1814. By 1804, Murdock had brought his apparatus to a point where Boulton \& Watt were able to canvas for orders. Murdock continued with the company after the death of James Watt in 1819, but retired in 1830 and continued to live at Sycamore House, Handsworth, near Birmingham.
    [br]
    Principal Honours and Distinctions
    Royal Society Rumford Gold Medal 1808.
    Further Reading
    S.Smiles, 1861, Lives of the Engineers, Vol. IV: Boulton and Watt, London: John Murray.
    H.W.Dickinson and R.Jenkins, 1927, James Watt and the Steam Engine, Oxford: Clarendon Press.
    J.A.McCash, 1966, "William Murdoch. Faithful servant" in E.G.Semler (ed.), The Great Masters. Engineering Heritage, Vol. II, London: Institution of Mechanical Engineers/Heinemann.
    IMcN

    Biographical history of technology > Murdock (Murdoch), William

  • 6 машина без охлаждения

    Универсальный русско-английский словарь > машина без охлаждения

  • 7 машина с конденсацией

    Railway term: condensing engine

    Универсальный русско-английский словарь > машина с конденсацией

  • 8 машина с охлаждением

    Универсальный русско-английский словарь > машина с охлаждением

  • 9 паровая машина с выхлопом в воздух

    Mechanic engineering: non-condensing engine

    Универсальный русско-английский словарь > паровая машина с выхлопом в воздух

  • 10 машина с выхлопом в атмосферу

    Русско-английский политехнический словарь > машина с выхлопом в атмосферу

  • 11 Kondensationsmaschine

    f < energ> (Dampfturbine) ■ condensing engine
    f < textil> ■ curing machine

    German-english technical dictionary > Kondensationsmaschine

  • 12 kondenzacijska parna mašina

    • condensing-steam engine

    Српски-Енглески Технички речник > kondenzacijska parna mašina

  • 13 kondenzacijska parna mašina

    • condensing-steam engine

    Serbian-English dictionary > kondenzacijska parna mašina

  • 14 Porter, Charles Talbot

    [br]
    b. 18 January 1826 Auburn, New York, USA
    d. 1910 USA
    [br]
    American inventor of a stone dressing machine, an improved centrifugal governor and a high-speed steam engine.
    [br]
    Porter graduated from Hamilton College, New York, in 1845, read law in his father's office, and in the autumn of 1847 was admitted to the Bar. He practised for six or seven years in Rochester, New York, and then in New York City. He was drawn into engineering when aged about 30, first through a client who claimed to have invented a revolutionary type of engine and offered Porter the rights to it as payment of a debt. Having lent more money, Porter saw neither the man nor the engine again. Porter followed this with a similar experience over a patent for a stone dressing machine, except this time the machine was built. It proved to be a failure, but Porter set about redesigning it and found that it was vastly improved when it ran faster. His improved machine went into production. It was while trying to get the steam engine that drove the stone dressing machine to run more smoothly that he made a discovery that formed the basis for his subsequent work.
    Porter took the ordinary Watt centrifugal governor and increased the speed by a factor of about ten; although he had to reduce the size of the weights, he gained a motion that was powerful. To make the device sufficiently responsive at the right speed, he balanced the centrifugal forces by a counterweight. This prevented the weights flying outwards until the optimum speed was reached, so that the steam valves remained fully open until that point and then the weights reacted more quickly to variations in speed. He took out a patent in 1858, and its importance was quickly recognized. At first he manufactured and sold the governors himself in a specially equipped factory, because this was the only way he felt he could get sufficient accuracy to ensure a perfect action. For marine use, the counterweight was replaced by a spring.
    Higher speed had brought the advantage of smoother running and so he thought that the same principles could be applied to the steam engine itself, but it was to take extensive design modifications over several years before his vision was realized. In the winter of 1860–1, J.F. Allen met Porter and sketched out his idea of a new type of steam inlet valve. Porter saw the potential of this for his high-speed engine and Allen took out patents for it in 1862. The valves were driven by a new valve gear designed by Pius Fink. Porter decided to display his engine at the International Exhibition in London in 1862, but it had to be assembled on site because the parts were finished in America only just in time to be shipped to meet the deadline. Running at 150 rpm, the engine caused a sensation, but as it was non-condensing there were few orders. Porter added condensing apparatus and, after the failure of Ormerod Grierson \& Co., entered into an agreement with Joseph Whitworth to build the engines. Four were exhibited at the 1867 Paris Exposition Universelle, but Whitworth and Porter fell out and in 1868 Porter returned to America.
    Porter established another factory to build his engine in America, but he ran into all sorts of difficulties, both mechanical and financial. Some engines were built, and serious production was started c. 1874, but again there were further problems and Porter had to leave his firm. High-speed engines based on his designs continued to be made until after 1907 by the Southwark Foundry and Machine Company, Philadelphia, so Porter's ideas were proved viable and led to many other high-speed designs.
    [br]
    Bibliography
    1908, Engineering Reminiscences, New York: J. Wiley \& Sons; reprinted 1985, Bradley, Ill.: Lindsay (autobiography; the main source of information about his life).
    Further Reading
    R.L.Hills, 1989, Power from Steam. A History of the Stationary Steam Engine, Cambridge University Press (examines his governor and steam engine).
    O.Mayr, 1974, "Yankee practice and engineering theory; Charles T.Porter and the dynamics of the high-speed engine", Technology and Culture 16 (4) (examines his governor and steam engine).
    RLH

    Biographical history of technology > Porter, Charles Talbot

  • 15 Priestman, William Dent

    [br]
    b. 23 August 1847 Sutton, Hull, England
    d. 7 September 1936 Hull, England
    [br]
    English oil engine pioneer.
    [br]
    William was the second son and one of eleven children of Samuel Priestman, who had moved to Hull after retiring as a corn miller in Kirkstall, Leeds, and who in retirement had become a director of the North Eastern Railway Company. The family were strict Quakers, so William was sent to the Quaker School in Bootham, York. He left school at the age of 17 to start an engineering apprenticeship at the Humber Iron Works, but this company failed so the apprenticeship was continued with the North Eastern Railway, Gateshead. In 1869 he joined the hydraulics department of Sir William Armstrong \& Company, Newcastle upon Tyne, but after a year there his father financed him in business at a small, run down works, the Holderness Foundry, Hull. He was soon joined by his brother, Samuel, their main business being the manufacture of dredging equipment (grabs), cranes and winches. In the late 1870s William became interested in internal combustion engines. He took a sublicence to manufacture petrol engines to the patents of Eugène Etève of Paris from the British licensees, Moll and Dando. These engines operated in a similar manner to the non-compression gas engines of Lenoir. Failure to make the two-stroke version of this engine work satisfactorily forced him to pay royalties to Crossley Bros, the British licensees of the Otto four-stroke patents.
    Fear of the dangers of petrol as a fuel, reflected by the associated very high insurance premiums, led William to experiment with the use of lamp oil as an engine fuel. His first of many patents was for a vaporizer. This was in 1885, well before Ackroyd Stuart. What distinguished the Priestman engine was the provision of an air pump which pressurized the fuel tank, outlets at the top and bottom of which led to a fuel atomizer injecting continuously into a vaporizing chamber heated by the exhaust gases. A spring-loaded inlet valve connected the chamber to the atmosphere, with the inlet valve proper between the chamber and the working cylinder being camoperated. A plug valve in the fuel line and a butterfly valve at the inlet to the chamber were operated, via a linkage, by the speed governor; this is believed to be the first use of this method of control. It was found that vaporization was only partly achieved, the higher fractions of the fuel condensing on the cylinder walls. A virtue was made of this as it provided vital lubrication. A starting system had to be provided, this comprising a lamp for preheating the vaporizing chamber and a hand pump for pressurizing the fuel tank.
    Engines of 2–10 hp (1.5–7.5 kW) were exhibited to the press in 1886; of these, a vertical engine was installed in a tram car and one of the horizontals in a motor dray. In 1888, engines were shown publicly at the Royal Agricultural Show, while in 1890 two-cylinder vertical marine engines were introduced in sizes from 2 to 10 hp (1.5–7.5 kW), and later double-acting ones up to some 60 hp (45 kW). First, clutch and gearbox reversing was used, but reversing propellers were fitted later (Priestman patent of 1892). In the same year a factory was established in Philadelphia, USA, where engines in the range 5–20 hp (3.7–15 kW) were made. Construction was radically different from that of the previous ones, the bosses of the twin flywheels acting as crank discs with the main bearings on the outside.
    On independent test in 1892, a Priestman engine achieved a full-load brake thermal efficiency of some 14 per cent, a very creditable figure for a compression ratio limited to under 3:1 by detonation problems. However, efficiency at low loads fell off seriously owing to the throttle governing, and the engines were heavy, complex and expensive compared with the competition.
    Decline in sales of dredging equipment and bad debts forced the firm into insolvency in 1895 and receivers took over. A new company was formed, the brothers being excluded. However, they were able to attend board meetings, but to exert no influence. Engine activities ceased in about 1904 after over 1,000 engines had been made. It is probable that the Quaker ethics of the brothers were out of place in a business that was becoming increasingly cut-throat. William spent the rest of his long life serving others.
    [br]
    Further Reading
    C.Lyle Cummins, 1976, Internal Fire, Carnot Press.
    C.Lyle Cummins and J.D.Priestman, 1985, "William Dent Priestman, oil engine pioneer and inventor: his engine patents 1885–1901", Proceedings of the Institution of
    Mechanical Engineers 199:133.
    Anthony Harcombe, 1977, "Priestman's oil engine", Stationary Engine Magazine 42 (August).
    JB

    Biographical history of technology > Priestman, William Dent

  • 16 Corliss, George Henry

    [br]
    b. 2 June 1817 Easton, Washington City, New York, USA
    d. 21 February 1888 USA
    [br]
    American inventor of a cut-off mechanism linked to the governor which revolutionized the operation of steam engines.
    [br]
    Corliss's father was a physician and surgeon. The son was educated at Greenwich, New York, but while he showed an aptitude for mathematics and mechanics he first of all became a storekeeper and then clerk, bookkeeper, salesperson and official measurer and inspector of the cloth produced at W.Mowbray \& Son. He went to the Castleton Academy, Vermont, for three years and at the age of 21 returned to a store of his own in Greenwich. Complaints about stitching in the boots he sold led him to patent a sewing machine. He approached Fairbanks, Bancroft \& Co., Providence, Rhode Island, machine and steam engine builders, about producing his machine, but they agreed to take him on as a draughtsman providing he abandoned it. Corliss moved to Providence with his family and soon revolutionized the design and construction of steam engines. Although he started working out ideas for his engine in 1846 and completed one in 1848 for the Providence Dyeing, Bleaching and Calendering Company, it was not until March 1849 that he obtained a patent. By that time he had joined John Barstow and E.J.Nightingale to form a new company, Corliss Nightingale \& Co., to build his design of steam-engines. He used paired valves, two inlet and two exhaust, placed on opposite sides of the cylinder, which gave good thermal properties in the flow of steam. His wrist-plate operating mechanism gave quick opening and his trip mechanism allowed the governor to regulate the closure of the inlet valve, giving maximum expansion for any load. It has been claimed that Corliss should rank equally with James Watt in the development of the steam-engine. The new company bought land in Providence for a factory which was completed in 1856 when the Corliss Engine Company was incorporated. Corliss directed the business activities as well as technical improvements. He took out further patents modifying his valve gear in 1851, 1852, 1859, 1867, 1875, 1880. The business grew until well over 1,000 workers were employed. The cylindrical oscillating valve normally associated with the Corliss engine did not make its appearance until 1850 and was included in the 1859 patent. The impressive beam engine designed for the 1876 Centennial Exhibition by E. Reynolds was the product of Corliss's works. Corliss also patented gear-cutting machines, boilers, condensing apparatus and a pumping engine for waterworks. While having little interest in politics, he represented North Providence in the General Assembly of Rhode Island between 1868 and 1870.
    [br]
    Further Reading
    Many obituaries appeared in engineering journals at the time of his death. Dictionary of American Biography, 1930, Vol. IV, New York: C.Scribner's Sons. R.L.Hills, 1989, Power from Steam. A History of the Stationary Steam Engine, Cambridge University Press (explains Corliss's development of his valve gear).
    J.L.Wood, 1980–1, "The introduction of the Corliss engine to Britain", Transactions of the Newcomen Society 52 (provides an account of the introduction of his valve gear to Britain).
    W.H.Uhland, 1879, Corliss Engines and Allied Steam-motors, London: E. \& F.N.Spon.
    RLH

    Biographical history of technology > Corliss, George Henry

  • 17 Robinson, George J.

    SUBJECT AREA: Textiles
    [br]
    b. 1712 Scotland
    d. 1798 England
    [br]
    Scottish manufacturer who installed the first Boulton \& Watt rotative steam-engine in a textile mill.
    [br]
    George Robinson is said to have been a Scots migrant who settled at Burwell, near Nottingham, in 1737, but there is no record of his occupation until 1771, when he was noticed as a bleacher. By 1783 he and his son were describing themselves as "merchants and thread manufacturers" as well as bleachers. For their thread, they were using the system of spinning on the waterframe, but it is not known whether they held a licence from Arkwright. Between 1776 and 1791, the firm G.J. \& J.Robinson built a series of six cotton mills with a complex of dams and aqueducts to supply them in the relatively flat land of the Leen valley, near Papplewick, to the north of Nottingham. By careful conservation they were able to obtain considerable power from a very small stream. Castle mill was not only the highest one owned by the Robinsons, but it was also the highest mill on the stream and was fed from a reservoir. The Robinsons might therefore have expected to have enjoyed uninterrupted use of the water, but above them lived Lord Byron in his estate of Newstead Priory. The fifth Lord Byron loved making ornamental ponds on his property so that he could have mock naval battles with his servants, and this tampered with the water supplies so much that the Robinsons found they were unable to work their mills.
    In 1785 they decided to order a rotative steam engine from the firm of Boulton \& Watt. It was erected by John Rennie; however, misfortune seemed to dog this engine, for parts went astray to Manchester and when the engine was finally running at the end of February 1786 it was found to be out of alignment so may not have been very successful. At about the same time, the lawsuit against Lord Byron was found in favour of the Robinsons, but the engine continued in use for at least twelve years and was the first of the type which was to power virtually all steamdriven mills until the 1850s to be installed in a textile mill. It was a low-pressure double-acting condensing beam engine, with a vertical cylinder, parallel motion connecting the piston toone end of a rocking beam, and a connecting rod at the other end of the beam turning the flywheel. In this case Watt's sun and planet motion was used in place of a crank.
    [br]
    Further Reading
    R.L.Hills, 1970, Power in the Industrial Revolution, Manchester (for an account of the installation of this engine).
    D.M.Smith, 1965, Industrial Archaeology of the East Midlands, Newton Abbot (describes the problems which the Robinsons had with the water supplies to power their mills).
    S.D.Chapman, 1967, The Early Factory Masters, Newton Abbot (provides details of the business activities of the Robinsons).
    J.D.Marshall, 1959, "Early application of steam power: the cotton mills of the Upper Leen", Transactions of the Thoroton Society of Nottinghamshire 60 (mentions the introduction of this steam-engine).
    RLH

    Biographical history of technology > Robinson, George J.

  • 18 Symington, William

    SUBJECT AREA: Ports and shipping
    [br]
    b. 1764 Leadhills, Lanarkshire, Scotland
    d. 22 March 1831 Wapping, London, England
    [br]
    Scottish pioneer of steam navigation.
    [br]
    Symington was the son of the Superintendent of the Mines Company in Lanarkshire, and attended the local school. When he was 22 years old he was sent by Gilbert Meason, Manager of the Wanlockhead mines, to Edinburgh University. In 1779 he was working on the assembly of a Watt engine as an apprentice to his brother, George, and in 1786 he started experiments to modify a Watt engine in order to avoid infringing the separate condenser patent. He sought a patent for his alternative, which was paid for by Meason. He constructed a model steam road carriage which was completed in 1786; it was shown in Edinburgh by Meason, attracting interest but inadequate financial support. It had a horizontal cylinder and was non-condensing. No full-sized engine was ever built but the model secured the interest of Patrick Miller, an Edinburgh banker, who ordered an engine from Symington to drive an experimental boat, 25 ft (7.6 m) long with a dual hull, which performed satisfactorily on Dalswinton Loch in 1788. In the following year Miller ordered a larger engine for a bigger boat which was tried on the Forth \& Clyde Canal in December 1789, the component parts having been made by the Carron Company. The engine worked perfectly but had the effect of breaking the paddle wheels. These were repaired and further trials were successful but Miller lost interest and his experiments lapsed. Symington devoted himself thereafter to building stationary engines. He built other engines for mine pumping at Sanquhar and Leadhills before going further afield. In all, he built over thirty engines, about half of them being rotary. In 1800–1 he designed the engine for a boat for Lord Dundas, the Charlotte Dundas; this was apparently the first boat of that name and sailed on both the Forth and Clyde rivers. A second Charlotte Dundas with a horizontal cylinder was to follow and first sailed in January 1803 for the Forth \& Clyde Canal Company. The speed of the boat was only 2 mph (3 km/h) and much was made by its detractors of the damage said to be caused to the canal banks by its wash. Lord Dundas declined to authorize payment of outstanding accounts; Symington received little reward for his efforts. He died in the house of his son-in-law, Dr Robert Bowie, in Wapping, amidst heated controversy about the true inventor of steam navigation.
    [br]
    Further Reading
    W.S.Harvey and G.Downs-Rose, 1980, William Symington, Inventor and Engine- Builder, London: Mechanical Engineering Publications.
    IMcN

    Biographical history of technology > Symington, William

  • 19 Trevithick, Richard

    [br]
    b. 13 April 1771 Illogan, Cornwall, England
    d. 22 April 1833 Dartford, Kent, England
    [br]
    English engineer, pioneer of non-condensing steam-engines; designed and built the first locomotives.
    [br]
    Trevithick's father was a tin-mine manager, and Trevithick himself, after limited formal education, developed his immense engineering talent among local mining machinery and steam-engines and found employment as a mining engineer. Tall, strong and high-spirited, he was the eternal optimist.
    About 1797 it occurred to him that the separate condenser patent of James Watt could be avoided by employing "strong steam", that is steam at pressures substantially greater than atmospheric, to drive steam-engines: after use, steam could be exhausted to the atmosphere and the condenser eliminated. His first winding engine on this principle came into use in 1799, and subsequently such engines were widely used. To produce high-pressure steam, a stronger boiler was needed than the boilers then in use, in which the pressure vessel was mounted upon masonry above the fire: Trevithick designed the cylindrical boiler, with furnace tube within, from which the Cornish and later the Lancashire boilers evolved.
    Simultaneously he realized that high-pressure steam enabled a compact steam-engine/boiler unit to be built: typically, the Trevithick engine comprised a cylindrical boiler with return firetube, and a cylinder recessed into the boiler. No beam intervened between connecting rod and crank. A master patent was taken out.
    Such an engine was well suited to driving vehicles. Trevithick built his first steam-carriage in 1801, but after a few days' use it overturned on a rough Cornish road and was damaged beyond repair by fire. Nevertheless, it had been the first self-propelled vehicle successfully to carry passengers. His second steam-carriage was driven about the streets of London in 1803, even more successfully; however, it aroused no commercial interest. Meanwhile the Coalbrookdale Company had started to build a locomotive incorporating a Trevithick engine for its tramroads, though little is known of the outcome; however, Samuel Homfray's ironworks at Penydarren, South Wales, was already building engines to Trevithick's design, and in 1804 Trevithick built one there as a locomotive for the Penydarren Tramroad. In this, and in the London steam-carriage, exhaust steam was turned up the chimney to draw the fire. On 21 February the locomotive hauled five wagons with 10 tons of iron and seventy men for 9 miles (14 km): it was the first successful railway locomotive.
    Again, there was no commercial interest, although Trevithick now had nearly fifty stationary engines completed or being built to his design under licence. He experimented with one to power a barge on the Severn and used one to power a dredger on the Thames. He became Engineer to a project to drive a tunnel beneath the Thames at Rotherhithe and was only narrowly defeated, by quicksands. Trevithick then set up, in 1808, a circular tramroad track in London and upon it demonstrated to the admission-fee-paying public the locomotive Catch me who can, built to his design by John Hazledine and J.U. Rastrick.
    In 1809, by which date Trevithick had sold all his interest in the steam-engine patent, he and Robert Dickinson, in partnership, obtained a patent for iron tanks to hold liquid cargo in ships, replacing the wooden casks then used, and started to manufacture them. In 1810, however, he was taken seriously ill with typhus for six months and had to return to Cornwall, and early in 1811 the partners were bankrupt; Trevithick was discharged from bankruptcy only in 1814.
    In the meantime he continued as a steam engineer and produced a single-acting steam engine in which the cut-off could be varied to work the engine expansively by way of a three-way cock actuated by a cam. Then, in 1813, Trevithick was approached by a representative of a company set up to drain the rich but flooded silver-mines at Cerro de Pasco, Peru, at an altitude of 14,000 ft (4,300 m). Low-pressure steam engines, dependent largely upon atmospheric pressure, would not work at such an altitude, but Trevithick's high-pressure engines would. Nine engines and much other mining plant were built by Hazledine and Rastrick and despatched to Peru in 1814, and Trevithick himself followed two years later. However, the war of independence was taking place in Peru, then a Spanish colony, and no sooner had Trevithick, after immense difficulties, put everything in order at the mines then rebels arrived and broke up the machinery, for they saw the mines as a source of supply for the Spanish forces. It was only after innumerable further adventures, during which he encountered and was assisted financially by Robert Stephenson, that Trevithick eventually arrived home in Cornwall in 1827, penniless.
    He petitioned Parliament for a grant in recognition of his improvements to steam-engines and boilers, without success. He was as inventive as ever though: he proposed a hydraulic power transmission system; he was consulted over steam engines for land drainage in Holland; and he suggested a 1,000 ft (305 m) high tower of gilded cast iron to commemorate the Reform Act of 1832. While working on steam propulsion of ships in 1833, he caught pneumonia, from which he died.
    [br]
    Bibliography
    Trevithick took out fourteen patents, solely or in partnership, of which the most important are: 1802, Construction of Steam Engines, British patent no. 2,599. 1808, Stowing Ships' Cargoes, British patent no. 3,172.
    Further Reading
    H.W.Dickinson and A.Titley, 1934, Richard Trevithick. The Engineer and the Man, Cambridge; F.Trevithick, 1872, Life of Richard Trevithick, London (these two are the principal biographies).
    E.A.Forward, 1952, "Links in the history of the locomotive", The Engineer (22 February), 226 (considers the case for the Coalbrookdale locomotive of 1802).
    PJGR

    Biographical history of technology > Trevithick, Richard

  • 20 машинное отделение

    1) General subject: engine-room
    3) Engineering: machine room
    4) Construction: engine house (здание), equipment room, machinery space, mechanical equipment room, plant room
    5) Railway term: power compartment
    10) Automation: engine shop

    Универсальный русско-английский словарь > машинное отделение

Страницы
  • 1
  • 2

См. также в других словарях:

  • Condensing engine — Condense Con*dense , v. t. [imp. & p. p. {Condensed}; p. pr. & vb. n. {Condensing}.] [L. condensare; con + densare to make thick or dense, densus thick, dense: cf. F. condenser. See {Dense}, and cf. {Condensate}.] 1. To make more close, compact,… …   The Collaborative International Dictionary of English

  • condensing engine — noun : a steam engine in which the steam after exhausting from the cylinder is condensed in a separate condenser …   Useful english dictionary

  • Engine — En gine ([e^]n j[i^]n), n. [F. engin skill, machine, engine, L. ingenium natural capacity, invention; in in + the root of gignere to produce. See {Genius}, and cf. {Ingenious}, {Gin} a snare.] 1. Note: (Pronounced, in this sense, [e^]n*j[=e]n .)… …   The Collaborative International Dictionary of English

  • Engine driver — Engine En gine ([e^]n j[i^]n), n. [F. engin skill, machine, engine, L. ingenium natural capacity, invention; in in + the root of gignere to produce. See {Genius}, and cf. {Ingenious}, {Gin} a snare.] 1. Note: (Pronounced, in this sense,… …   The Collaborative International Dictionary of English

  • Engine lathe — Engine En gine ([e^]n j[i^]n), n. [F. engin skill, machine, engine, L. ingenium natural capacity, invention; in in + the root of gignere to produce. See {Genius}, and cf. {Ingenious}, {Gin} a snare.] 1. Note: (Pronounced, in this sense,… …   The Collaborative International Dictionary of English

  • Engine tool — Engine En gine ([e^]n j[i^]n), n. [F. engin skill, machine, engine, L. ingenium natural capacity, invention; in in + the root of gignere to produce. See {Genius}, and cf. {Ingenious}, {Gin} a snare.] 1. Note: (Pronounced, in this sense,… …   The Collaborative International Dictionary of English

  • Engine turning — Engine En gine ([e^]n j[i^]n), n. [F. engin skill, machine, engine, L. ingenium natural capacity, invention; in in + the root of gignere to produce. See {Genius}, and cf. {Ingenious}, {Gin} a snare.] 1. Note: (Pronounced, in this sense,… …   The Collaborative International Dictionary of English

  • Condensing — Condense Con*dense , v. t. [imp. & p. p. {Condensed}; p. pr. & vb. n. {Condensing}.] [L. condensare; con + densare to make thick or dense, densus thick, dense: cf. F. condenser. See {Dense}, and cf. {Condensate}.] 1. To make more close, compact,… …   The Collaborative International Dictionary of English

  • engine — Synonyms and related words: AC motor, Corliss engine, Otto engine, Wankel engine, aeromotor, air engine, alembic, anvil, apparatus, appliance, arc jet engine, axial flow turbojet, beam engine, bearings, blowing engine, boiler, caldron, cam, cam… …   Moby Thesaurus

  • compound engine — noun 1. : an engine (as a steam engine) in which the working fluid is expanded successively in two distinct phases so as to minimize losses (as from cylinder condensation) and so allow a high ratio of expansion to be used, the working fluid (as… …   Useful english dictionary

  • Low-pressure steam engine — Low pressure Low pres sure, a. 1. Having, employing, or exerting, a low degree of pressure. [1913 Webster] 2. same as {easygoing}, 4; as, a low pressure salesman. Syn: easygoing. [WordNet 1.5] {Low pressure steam engine}, a steam engine in which… …   The Collaborative International Dictionary of English

Поделиться ссылкой на выделенное

Прямая ссылка:
… Нажмите правой клавишей мыши и выберите «Копировать ссылку»