-
21 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
- 1
- 2
См. также в других словарях:
code, area — See code, numbering plan area … IT glossary of terms, acronyms and abbreviations
Area code 602 — Area code 775poly 73 58 68 92 64 92 58 88 48 88 51 125 49 135 13 98 10 58 Area code 702poly 74 49 250 49 250 1 73 1 Area code 435poly 250 0 319 0 319 51 249 49 Area code 970poly 248 50 322 51 318 279 286 281 289 299 256 299 Area code 505poly 0 84 … Wikipedia
Area code 813 — is the telephone numbering plan code for the city of Tampa, Florida and surrounding areas such as Zephyrhills and Oldsmar.DescriptionArea code 813 covers all of Hillsborough County, the eastern two thirds of Pasco County, and the city of Oldsmar… … Wikipedia
Area code 308 — Area code 605poly 477 147 389 154 383 146 386 131 376 103 374 104 372 95 369 77 359 58 356 49 343 41 354 12 347 7 350 1 477 0 Area code 712poly 390 155 408 186 416 192 420 191 425 182 418 178 418 175 449 173 449 180 463 185 472 176 480 179 480… … Wikipedia
Area codes 601 and 769 — are the telephone area codes for central Mississippi. Originally, area code 601 covered the entire state. In 1997, area code 228 was created for the Mississippi Gulf Coast area. In 1999, area code 662 was created in the northern half of… … Wikipedia
Area code 805 — is a California telephone area code. Area code 805 includes most or all of the California counties of San Luis Obispo, Santa Barbara, and Ventura, plus southernmost portions of Monterey County, and a small portion of Los Angeles County.Area code… … Wikipedia
Area code 502 — serves the state of Kentucky s north central counties, primarily Louisville, its suburbs, and the state capital Frankfort. Its service area encompasses the following Kentucky counties (the boundary closely, but not exactly, tracks county… … Wikipedia
Area code 475 — is a proposed telephone area code to serve southwestern Connecticut; it will overlay the existing 203 area code. A date for implementing this new overlay area code has yet to be determined; however, it was announced in September 2008 that it… … Wikipedia
code — [kəʊd ǁ koʊd] noun 1. [countable] LAW a complete set of written rules or laws: • Each state in the US has a different criminal and civil code. ˈbuilding code [countable] LAW a set of rules that states what features a new building, bridge etc… … Financial and business terms
Area code 518 — is a telephone area code in eastern upstate New York. It is the largest area code area in the state, extending from the eastern Mohawk Valley to east of Albany and from the Canadian border to the upper Hudson Valley. The boundary of the New York… … Wikipedia
area code — ➔ code * * * area code UK US noun [C] COMMUNICATIONS ► a series of numbers that you use before the main phone number when you phone someone outside your own city or area → Compare DIALLING CODE(Cf. ↑dialling code) … Financial and business terms
