-
1 двухполюсный автоматический выключатель
двухполюсный автоматический выключатель
-EN
two-pole circuit-breaker
circuit-breaker with two independent electrically separated conducting paths for the main circuit
NOTE 1 The two paths may be connected in series for use in a single phase circuit where the establishment and the seperation of the two paths are simultaneous.
NOTE 2 The construction arrangement of this device is in principle identical to two phases of a three phase circuit-breaker.
[IEC 62505-1, ed. 1.0 (2009-03)]FR
disjoncteur bipolaire
disjoncteur constitué de deux circuits principaux indépendants conducteurs, électriquement séparés
NOTE 1 Les deux pôles peuvent être connectés en série pour une utilisation dans un circuit monophasé où l'établissement et la coupure des deux circuits sont simultanés.
NOTE 2 La disposition constructive de cet appareil est en principe identique à deux phases d'un disjoncteur triphasé.
[IEC 62505-1, ed. 1.0 (2009-03)]Рис. Schneider ElectricНедопустимые, нерекомендуемые
Тематики
Классификация
>>>Обобщающие термины
EN
FR
Русско-французский словарь нормативно-технической терминологии > двухполюсный автоматический выключатель
2 устройство с двумя выводами
устройство с двумя выводами
-
[IEV number 151-12-13]EN
two-terminal device
device having two terminals, or device having more than two terminals where only the performance at two terminals forming a pair is of interest
NOTE – In French, the term "bipôle" is also used for a two-terminal element or a two-terminal network in circuit theory.
Source: see IEC 60050-131
[IEV number 151-12-13]FR
bipôle, m
dipôle (terme déconseillé dans ce sens), m
dispositif à deux bornes, ou à plus de deux bornes lorsque le comportement, vu de deux bornes formant une paire, est seul pris en considération
NOTE – En français, le terme "bipôle" est aussi employé pour un élément de circuit ou un réseau à deux bornes en théorie des circuits.
Source: voir la CEI 60050-131
[IEV number 151-12-13]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > устройство с двумя выводами
3 расстояние утечки
расстояние утечки
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание. Стык между двумя элементами из изоляционного материала считают частью поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
расстояние утечки (см. приложение В)
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание — При определении расстояния утечки относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9
[ ГОСТ Р 50345-99( МЭК 60898-95)]
расстояние утечки по поверхности
-
[IEV number 151-15-50]
путь утечки
Кратчайшее расстояние вдоль поверхности изоляции между двумя проводящими частями или между проводящей частью и доступной поверхностью.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - A joint between two pieces of insulating material is considered part of the surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - For the purpose of determining a creepage distance to accessible parts, the accessible surface of an insulating enclosure is considered conductive as if it was covered by a metal foil wherever it can be touched by a hand or a standard test finger according to figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
creepage distance
shortest distance along the surface of insulation between two conductive parts or between a conductive part and the accessible surface
[IEC 60335-1, ed. 4.0 (2001-05)]
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts
[IEV number 151-15-50]FR
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Un joint entre deux portions de matière isolante est considéré comme faisant partie de la surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Pour la détermination d'une ligne de fuite pour des parties accessibles, la surface accessible d'une enveloppe isolante est considérée comme conductrice comme si elle était recouverte d'une feuille métallique à tout endroit où elle peut être touchée par la main ou par le doigt d'essai normalisé conforme à la figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
ligne de fuite
plus petite distance le long de la surface de l’isolation entre deux parties conductrices ou entre une partie conductrice et la surface accessible
[IEC 60335-1, ed. 4.0 (2001-05)]
ligne de fuite, f
distance la plus courte, le long de la surface d'un isolant solide, entre deux parties conductrices
[IEV number 151-15-50]1) Должно быть проводящими
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > расстояние утечки
4 бифилярная обмотка
бифилярная обмотка
-
[IEV number 151-13-18]EN
bifilar winding
set of two coils the turns of which consist of two contiguous conductors isolated from one another
NOTE – The inductive leakage factor of the two coils of a bifilar winding is generally negligible.
[IEV number 151-13-18]FR
enroulement bifilaire, m
ensemble de deux bobines dont les spires sont formées de deux conducteurs juxtaposés isolés l'un de l'autre
NOTE – Le facteur de dispersion inductif des deux bobines d’un enroulement bifilaire est généralement négligeable.
[IEV number 151-13-18]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > бифилярная обмотка
5 двухконсольный ротор
двухконсольный ротор
Ротор, существенная часть массы которого расположена за крайними опорами.
[ ГОСТ 19534-74]Тематики
EN
DE
FR
D. Zweikonsolenrotor
E. Two-outboard (Two-console) rotor
F. Rotor a deux consoles
Ротор, существенная часть массы которого расположена за крайними опорами (см. черт. 3 приложения 3)
Источник: ГОСТ 19534-74: Балансировка вращающихся тел. Термины оригинал документа
Русско-французский словарь нормативно-технической терминологии > двухконсольный ротор
6 воздушный зазор
- entrefer, m (2)
- distance d’isolement dans l’air
- distance d'isolement
воздушный зазор
Кратчайшее расстояние между двумя токоведущими и/или токоведущей и открытой проводящей частью.
МЭК 60050(441-17-31).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
воздушный зазор
Кратчайшее расстояние в воздухе между двумя токопроводящими1) частями вдоль линии наименьшей протяженности между этими токоведущими1) частями.
Примечание. Для определения воздушного зазора относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9.
(МЭС 441-17-31)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
1) Должно быть проводящими
[Интент]
изоляционный промежуток
Расстояние между двумя токопроводящими частями вдоль нити, натянутой по кратчайшему пути между ними.
[ ГОСТ Р 52726-2007]
зазор
Кратчайшее расстояние по воздуху между двумя токопроводящими1) частями оборудования.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
1) Должно быть проводящими
[Интент]EN
clearance
the distance between two conductive parts along a string stretched the shortest way between these conductive parts
[IEV number 441-17-31]
clearance
shortest distance in air between two conductive parts
NOTE – This distance applies only to parts that are exposed to the atmosphere and not to parts which are insulated parts or covered with casting compound.
[IEV number 426-04-12]FR
distance d'isolement
distance entre deux parties conductrices le long d'un fil tendu suivant le plus court trajet possible entre ces deux parties conductrices
[IEV number 441-17-31]
distance d’isolement dans l’air
plus courte distance dans l’air entre deux pièces conductrices
NOTE – Cette distance s'applique seulement aux parties exposées à l'atmosphère et non aux parties isolées ou recouvertes par un composé de moulage.
[IEV number 426-04-12]
Параллельные тексты EN-RU
Clearance distance
Shortest distance in air between two conductive parts or between a conductive part and the accessible surface of the relay.
[Tyco Electronics]Воздушный зазор
Кратчайшее расстояние по воздуху между двумя проводящими частями или между проводящей частью и доступной для прикосновения поверхностью реле.
[Перевод Интент]
Наименьшее изоляционное расстояние по воздуху (в свету) от токоведущих до заземленных частей опоры
[ПУЭ]
2
воздушный зазор
-
[IEV number 151-14-05]EN
air gap
short gap in the magnetic material forming a magnetic circuit
Source: 221-04-13 MOD
[IEV number 151-14-05]FR
entrefer, m
coupure de faible longueur dans le matériau magnétique constituant un circuit magnétique
Source: 221-04-13 MOD
[IEV number 151-14-05]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- air clearance
- air distance
- air gap (2)
- air-gap clearance
- clearance
- contact gap (1)
- contact opening distance (1)
- contact separation (1)
- flashover distance
- insulation clearanse
- insulation distance
- isolating distance
DE
FR
- distance d'isolement
- distance d’isolement dans l’air
- entrefer, m (2)
Русско-французский словарь нормативно-технической терминологии > воздушный зазор
7 двухпроводная сеть постоянного тока
двухпроводная сеть постоянного тока
-EN
two-wire d.c. system
d.c. system comprising two conductors only, between which the load is connected
[IEC 60092-201, 2.2.1]FR
distribution à courant continu à deux fils
réseau à courant continu ne comprenant que deux conducteurs entre lesquels est branchée la charge
[IEC 60092-201, 2.2.1]Тематики
EN
- two-wire d.c. system
FR
Русско-французский словарь нормативно-технической терминологии > двухпроводная сеть постоянного тока
8 двухступенчатый двухпозиционный пускатель
двухступенчатый двухпозиционный пускатель
Пускатель с единственной промежуточной позицией разгона между положениями включения и отключения.
Пример. Двухступенчатым является пускатель со схемой звезда — треугольник.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]EN
two-step starter
starter in which there is only one intermediate accelerating position between the OFF and ON positions
EXAMPLE - A star-delta starter is a two-step starter.
[IEC 60947-4-1, ed. 3.0 (2009-09)]FR
démarreur à deux étapes
démarreur dans lequel il n'existe qu'une seule position intermédiaire d'accélération entre la position ARRET et la position MARCHE
EXEMPLE - Un démarreur étoile-triangle est un démarreur à deux étapes.
[IEC 60947-4-1, ed. 3.0 (2009-09)]Тематики
- аппарат, изделие, устройство...
- контакторы и пускатели
Синонимы
EN
FR
Русско-французский словарь нормативно-технической терминологии > двухступенчатый двухпозиционный пускатель
9 двухтактный двигатель
двухтактный двигатель
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
two-stroke engine
An internal combustion engine whose cycle is completed in two strokes of the piston. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > двухтактный двигатель
10 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
11 переключающий контакт
переключающий контакт электрической цепи
Контакт электрической цепи, который размыкает одну электрическую цепь и замыкает другую при заданном действии устройства
[ ГОСТ 14312-79]
переключающий контакт
switching contact
Механический контакт, предназначенный для замыкания и размыкания электрической цепи.
[ ГОСТ Р МЭК 60050-426-2006]EN
change-over contact
combination of two contact circuits with three contact members, one of which is common to the two contact circuits; such that when one of these contact circuits is open, the other is closed
[IEV number 444-04-19]FR
contact à deux directions, m
contact inverseur (déconseillé), m
combinaison de deux circuits de contact comprenant trois éléments de contact, l'un d'eux étant commun aux deux circuits de contact ; de telle manière que lorsque l'un des circuits de contact est ouvert, l'autre est fermé
[IEV number 444-04-19]Параллельные тексты EN-RU CO contact
Compound contact consisting of a NO (make) contact and a NC (break) contact with a common terminal. On changing the switch position, the contact previously closed opens first followed by the closing of the contact that was previously open. Note: in case of a switching arc the NO and NC contact may be temporarily electrically connected.
[Tyco Electronics]Переключающий контакт
Контакт, объединяющий в себе замыкающий и размыкающий контакты с общим выводом. При изменении коммутационного положения сначала размыкается ранее замкнутый контакт, затем замыкается контакт, который до этого был разомкнут. Примечание. Если в процессе коммутации возникнет дуга между размыкающим и замыкающим контактами, то между ними может установиться кратковременная электрическая связь.
[Перевод Интент]Недопустимые, нерекомендуемые
Тематики
Обобщающие термины
Синонимы
EN
- C/O
- change-over contact
- changeover contact
- CO contact
- double-throw contact
- make-and-break contact
- switching contact
- transfer contact
- two-way contact
DE
FR
Русско-французский словарь нормативно-технической терминологии > переключающий контакт
12 полициклический углеводород
полициклический углеводород
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
polycyclic hydrocarbon
Hydrocarbon molecule with two or more nuclei; examples are naphtalene, with two benzene rings side by side, or diphenyl, with two bond-connected benzene rings. Also known as polynuclear hydrocarbon. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > полициклический углеводород
13 система кабельных коробов
система кабельных коробов
Система замкнутых оболочек, состоящих из основания (корпуса) и съемной крышки, предназначенная дляполного заключения в себяпрокладки внутри неё изолированных проводов, кабелей, шнуров и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60050-826-2009]
система кабельных коробов
Система замкнутых оболочек, состоящих из корпуса со съемной или открывающейся крышкой, предназначенная для прокладки внутри нее изолированных проводов, кабелей и шнуров и/или для размещения другого электрооборудования.
[ ГОСТ Р МЭК 61084-1 2007]
кабельнесущая система
Система закрытых оболочек, допускающая размещение изолированных проводов на базе подвижных поверхностей и предназначенная для полной защиты изолированных проводов, кабелей, шнуров, а также для размещения другого электрооборудования.
система кабельных коробов
Система закрываемых полых конструкций, состоящая из основания (корпуса) и съемной крышки, предназначенная для прокладки внутри них и защиты от механических повреждений кабелей, шнуров, изолированных проводов и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
cable trunking system
a system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electrical accessories
Source: 826-06-04 MOD
[IEV number 442-02-34]
cable trunking system
system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electric equipment including information technology equipment
Source: 442-02-34 MOD
[IEV number 826-15-04]
[IEC 60204-1-2006]FR
système de goulottes
ensemble d'enveloppes fermées munies d'un fond avec un couvercle amovible et destiné à la protection complète de conducteurs isolés et de câbles, ou au logement d'autre petit appareillage électrique
Source: 826-06-04 MOD
[IEV number 442-02-34]
système de goulottes, m
ensemble d'enveloppes fermées, munies d'un fond avec un couvercle amovible et destiné à la protection complète des conducteurs isolés et des câbles et/ou au logement d'autres matériels électriques y compris des matériels de traitement de l'information
Source: 442-02-34 MOD
[IEV number 826-15-04]Обратите внимание!
Различают два вида систем кабельных коробов:
1) (просто) система кабельных коробов (cable trunking system) - система любого сечения, но обязательно с крышкой;
2) система специальных кабельных коробов (cable ducting system) - система некруглого сечения и без крышек.
Примечание. В ПУЭ короб без крышки называется глухой короб (см. кабельный короб)
[Автор карточки]
Параллельные тексты EN-RU
Raceways shall be one- or two-piece design with base and snap-on cover, or three-piece design with base and two snap-on covers which snap side by side on a common base.
[Legrand/Wiremold. SECTION 16130 RACEWAY AND BOXES]В состав поставки входят специальные (глухие) кабельные короба, а также кабельные короба, состоящие из основания и защелкивающейся крышки, или из основания и двух защелкивающихся крышек.
[Перевод Интент]
1 - Система кабельных коробов
Система кабельных коробов
Система кабельных коробов
Недопустимые, нерекомендуемые
Примечание(1) - мнение автора карточкиТематики
- изделие электромонтажное
- электропроводка, электромонтаж
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > система кабельных коробов
14 степень защиты (обеспечиваемая оболочкой)
степень защиты
Способ защиты, обеспечиваемый оболочкой от доступа к опасным частям, попадания внешних твердых предметов и (или) воды и проверяемый стандартными методами испытаний.
[ ГОСТ 14254-96( МЭК 529-89)]
степень защиты, обеспечиваемая оболочкой (IP)
Числовые обозначения после кода IP, которые в соответствии с МЭК 60529 [12] характеризуют оболочку электрооборудования, обеспечивающую:
- защиту персонала от прикасания или доступа к находящимся под напряжением или движущимся частям (за исключением гладких вращающихся валов и т.п.), расположенным внутри оболочки;
- защиту электрооборудования от проникания в него твердых посторонних тел и,
- если указано в обозначении, защиту электрооборудования от вредного проникания воды.
[ ГОСТ Р МЭК 60050-426-2006]EN
degree of protection of enclosure
IP (abbreviation)
numerical classification according to IEC 60529 preceded by the symbol IP applied to the enclosure of electrical apparatus to provide:
– protection of persons against contact with, or approach to, live parts and against contact with moving parts (other than smooth rotating shafts and the like) inside the enclosure,
– protection of the electrical apparatus against ingress of solid foreign objects, and
– where indicated by the classification, protection of the electrical apparatus against harmful ingress of water
[IEV number 426-04-02 ]FR
degré de protection procuré par une enveloppe
IP (abréviation)
classification numérique selon la CEI 60529, précédée du symbole IP, appliquée à une enveloppe de matériel électrique pour apporter:
– une protection des personnes contre tout contact ou proximité avec des parties actives et contre tout contact avec une pièce mobile (autre que les roulements en faible rotation) à l'intérieur d'une enveloppe
– une protection du matériel électrique contre la pénétration de corps solide étrangers, et
– selon l’indication donnée par la classification, une protection du matériel électrique contre la pénétration dangereuse de l’eau
[IEV number 426-04-02 ]Элементы кода IP и их обозначения по ГОСТ 14254-96( МЭК 529-89)
Цифры кода IP
Значение для защиты оборудования от проникновения внешних твердых предметов
Значение для защиты людей от доступа к опасным частям
Первая характеристическая цифра
0
Нет защиты
Нет защиты
1
диаметром ≥ 50 мм
тыльной стороной руки
2
диаметром ≥ 12,5 мм
пальцем
3
диаметром ≥ 2,5 мм
инструментом
4
диаметром ≥ 1,0 мм
проволокой
5
пылезащищенное
проволокой
6
пыленепроницаемое
проволокой
От вредного воздействия в результате проникновения воды
Вторая характеристическая цифра
0
Нет защиты
-
1
Вертикальное каплепадение
2
Каплепадение (номинальный угол 15°)
3
Дождевание
4
Сплошное обрызгивание
5
Действие струи
6
Сильное действие струи
7
Временное непродолжительное погружение
8
Длительное погружение
Дополнительная буква (при необходимости)
-
От доступа к опасным частям
A
тыльной стороной руки
B
пальцем
C
инструментом
проволокой
Вспомогательная буква (при необходимости)
Вспомогательная информация относящаяся к:
-
H
высоковольтным аппаратам
M
состоянию движения во время испытаний защиты от воды
S
состоянию неподвижности во время испытаний защиты от воды
W
Требования в части стойкости оболочек и электрооборудования в целом к климатическим, механическим внешним воздействующим факторам (ВВФ) и специальным средам (кроме проникновения внешних твердых предметов и воды) установлены вне рамок настоящего стандарта.
Параллельные тексты EN-RU
The code IP indicates the degrees of protection provided by an enclosure against access to hazardous parts, ingress of solid foreign objects and ingress of water.
The degree of protection of an enclosure is identified, in compliance with the specifications of the Standard IEC 60529, by the code letters IP (International Protection) followed by two numerals and two additional letters.
The first characteristic numeral indicates the degree of protection against ingress of solid foreign objects and against contact of persons with hazardous live parts inside the enclosure.
The second characteristic numeral indicates the degree of protection against ingress of water with harmful effects.
[ABB]Код IP обозначает степень защиты, обеспечиваемую оболочкой от попадания внутрь твердых посторонних предметов и воды.
Степень защиты оболочки обозначается в соответствии со стандартом МЭК 60529 буквенным обозначением IP (International Protection, т. е. Международная защита) после которого следуют две цифры, к которым в некоторых случаях добавляются еще две буквы.
Первая характеристическая цифра обозначает степень защиты от проникновения твердых посторонних предметов и от контакта людей с находящимися внутри оболочки опасными токоведущими частями.
Вторая характеристическая цифра обозначает степень защиты оболочки с точки зрения вредного воздействия, оказываемого проникновением воды.
[Перевод Интент]The protection of enclosures against ingress of dirt or against the ingress of water is defined in IEC529 (BSEN60529:1991). Conversely, an enclosure which protects equipment against ingress of particles will also protect a person from potential hazards within that enclosure, and this degree of protection is also defined as a standard.
The degrees of protection are most commonly expressed as ‘IP’ followed by two numbers, e.g. IP65, where the numbers define the degree of protection. The first digit shows the extent to which the equipment is protected against particles, or to which persons are protected from enclosed hazards. The second digit indicates the extent of protection against water.
The wording in the table is not exactly as used in the standards document, but the dimensions are accurateIP Degree of Protection according to EN/IEC 60529
Correlations between IP (IEC) and NEMA 250 standards
IP10 -> NEMA 1
IP11 -> NEMA 2
IP54 -> NEMA 3 R
IP52 -> NEMA 5-12-12 K
IP54 -> NEMA 3-3 S
IP56 -> NEMA 4-4 X
IP67 -> NEMA 6-6 P[ http://electrical-engineering-portal.com/ip-protection-degree-iec-60529-explained]
Тематики
- безопасность машин и труда в целом
- электробезопасность
- электротехника, основные понятия
Действия
- степень защиты
- степень защиты, обеспечиваемая оболочкой
- степень защиты, обеспечиваемая оболочкой (код IP)
EN
- amount of protection
- degree of protection IP
- degree of protection of an enclosure
- degree of protection of enclosure
- degree of protection provided by enclosure
- enclosure rating
- ingress protection rating
- IP
- IP degree of protection,
- IP rating
- IP Sealing Specification
- IP security
- IPSec
- level of protection
- mechanical rating
- protection
- protection index
- protection rating
DE
- IP-Schutzgrad, m
- Schutzart des Gehäuses, f
FR
Русско-французский словарь нормативно-технической терминологии > степень защиты (обеспечиваемая оболочкой)
15 ворота двупольные
ворота двупольные
Ворота 2., состоящие из двух раздвижных или распашных вертикальных полотен
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ворота двупольные
16 выключатель с переключающим контактом
выключатель с переключающим контактом
-
[Интент]EN
changeover switch
A changeover switch, more commonly called an SPDT switch, is a type of switch that can be positioned in two closed states. The switch has three pins: the "common" (C) pin, the "normally closed" (NC) pin, which is connected to the common pin when the switch is not pressed, and the "normally open" (NO) pin, which is connected to the common pin when the switch is pressed.
[Wikimedia]
single-pole-double-throw switch
SPDT
device with a single input and two outputs, which is transferring the through connection from one output to the other output with switch actuation
[IEC 62047-5, ed. 1.0 (2011-07)]FR
commutateur unipolaire bidirectionnel
SPDT
dispositif à une seule entrée et deux sorties, qui transfère la connexion d’une sortie à l’autre sur l'actionnement du commutateur
[IEC 62047-5, ed. 1.0 (2011-07)]Тематики
- выключатель, переключатель
EN
FR
Русско-французский словарь нормативно-технической терминологии > выключатель с переключающим контактом
17 двухвальный ГТД
двухвальный ГТД
Ндп. двухкаскадный ГТД
ГТД, имеющий два соосных, механически не связанных вала, на которых установлены отдельные каскады компрессоров и вращающих их турбин.
[ ГОСТ 23851-79]Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
3. Двухвальный ГТД
Ндп. Двухкаскадный ГТД
D. Zweiwellen-Gasturbinentriebwerk
Е. Two-shaft gas turbine engine
F. Turbomoteur double corps
ГТД, имеющий два соосных, механически не связанных вала, на которых установлены отдельные каскады компрессоров и вращающих их турбин
Источник: ГОСТ 23851-79: Двигатели газотурбинные авиационные. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > двухвальный ГТД
18 двухкантный брус
двухкантный брус
Брус с двумя противоположными обработанными пластями.
[ ГОСТ 18288-87]Тематики
EN
DE
FR
17. Двухкантный брус
D. Zweikantholz (Model)
E. Two-edge cant
F. Bois aligné à deux faces
Брус с двумя противоположными обработанными пластями
Источник: ГОСТ 18288-87: Производство лесопильное. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > двухкантный брус
19 двухкаскадный компрессор
двухкаскадный компрессор
Компрессор ГТД, состоящий из двух последовательно расположенных каскадов компрессоров.
[ ГОСТ 23851-79]Тематики
EN
DE
FR
67. Двухкаскадный компрессор
D. Zweiwellenverdichter
E. Two spool compressor
F. Compresseur double corps
Компрессор ГТД, состоящий из двух последовательно расположенных каскадов компрессоров
Источник: ГОСТ 23851-79: Двигатели газотурбинные авиационные. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > двухкаскадный компрессор
20 двухкоординатный самописец
двухкоординатный самописец
-
[IEV number 313-02-04]EN
X-Y recorder
recording instrument in which the marking device is moved along two orthogonal axes by two separate devices, to each of which a quantity to be recorded is applied
[IEV number 313-02-04]FR
enregistreur X-Y
appareil enregistreur dans lequel le dispositif d'inscription est déplacé le long de deux axes orthogonaux par deux dispositifs distincts à chacun desquels est appliquée une grandeur à enregistrer
[IEV number 313-02-04]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > двухкоординатный самописец
См. также в других словарях:
Two and a Half Men — Genre Sitcom Created by Chuck Lorre Lee Aronsohn … Wikipedia
Two-wheel tractor — in Italy (2008) Two wheel tractor or walking tractor are generic terms understood in the USA and in parts of Europe to represent a single axle tractor, which is a tractor with one axle, self powered and self propelled, which can pull and power… … Wikipedia
Two-factor authentication — (TFA, T FA or 2FA) is an approach to authentication which requires the presentation of two different kinds of evidence that someone is who they say they are. It is a part of the broader family of multi factor authentication, which is a defense in … Wikipedia
Two-Face — ist eine fiktive Figur an der der US amerikanische Unterhaltungskonzern Time Warner die Rechte hält. Der Charakter ist die Hauptfigur einer Reihe von Comicpublikationen im Programm des zu Time Warner gehörenden Verlages DC Comics und hat ferner… … Deutsch Wikipedia
Two Face — ist eine fiktive Figur im Besitz von Time Warner, die in Comics des US amerikanischen Verlages DC auftritt, insbesondere in jenen des Batman Segments des Verlages. Darüber hinaus hat der Charakter eine gewisse popkulturelle Bedeutung und… … Deutsch Wikipedia
Two — (t[=oo]), a. [OE. two, twa, properly fem. & neut., twei, twein, tweien, properly masc. (whence E. twain), AS. tw[=a], fem. & neut., tw[=e]gen, masc., t[=u], neut.; akin to OFries. tw[=e]ne, masc., tw[=a], fem. & neut., OS. tw[=e]ne, masc., tw[=a] … The Collaborative International Dictionary of English
Two-photon excitation microscopy — is a fluorescence imaging technique that allows imaging of living tissue up to a very high depth, that is up to about one millimeter. Being a special variant of the multiphoton fluorescence microscope, it uses red shifted excitation light which… … Wikipedia
Two-dimensional nuclear magnetic resonance spectroscopy — (2D NMR) is a set of nuclear magnetic resonance spectroscopy (NMR) methods which give data plotted in a space defined by two frequency axes rather than one. Types of 2D NMR include correlation spectroscopy (COSY), J spectroscopy, exchange… … Wikipedia
two — [tu:] number [: Old English; Origin: twa] 1.) the number 2 ▪ I ll be away for almost two weeks. ▪ We have to be there by two (=two o clock) . ▪ His family moved to Australia when he was two (=two years old) . 2.) in twos in groups of two people… … Dictionary of contemporary English
Two-body problem — Two bodies with similar mass orbiting around a common barycenter with elliptic orbits. In classical mechanics, the two body problem is to determine the motion of two point particles that interact only with each other. Common examples include a… … Wikipedia
Two-Gun Kid — (Matt Hawk / Matt Liebowicz) Art by Scott Kolins. Publication information Publisher Marvel Comics … Wikipedia
Перевод: с русского на французский
с французского на русский- С французского на:
- Русский
- С русского на:
- Все языки
- Английский
- Итальянский
- Латинский
- Немецкий
- Персидский
- Французский
- Эстонский