-
1 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
2 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
3 étang de stabilisation
хранилище жидких отходов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
stabilisation lagoon
Ponds in which wastes are allowed to decompose over long periods of time and aeration is provided only by wind action. Sunlight is allowed to fall on sewage to purify it. (Source: PARCOR / PHC)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > étang de stabilisation
-
4 ciseau
ciseau mTir de volée en extension en position horizontal dans l'air, où l'impulsion et le tir sont réalisés avec la même jambe, les deux jambes se croisant dans les airs.► Un ciseau est autorisé si, de l'avis de l'arbitre, cela ne représente pas un danger pour un joueur adverse.
Technique in which a player strikes the ball with his foot over his head and in the direction of the opposing goal while horizontal in mid-air.► A scissors kick is allowed provided that it does not endanger the opposing player, in the opinion of the referee.
Syn. volley -
5 gardien
Joueur chargé de protéger le but de son équipe de manière à ce que le ballon ne franchisse pas la ligne de but et qui peut, pour ce faire, utiliser tout son corps, y compris ses bras et ses mains, dans sa propre surface de réparation, contrairement aux autres joueurs.Player positioned in the goalmouth whose task is to stop the ball from crossing the goal line and who is the only player in the team allowed to handle the ball provided, if he is inside his own penalty area. -
6 gardien de but
Joueur chargé de protéger le but de son équipe de manière à ce que le ballon ne franchisse pas la ligne de but et qui peut, pour ce faire, utiliser tout son corps, y compris ses bras et ses mains, dans sa propre surface de réparation, contrairement aux autres joueurs.Player positioned in the goalmouth whose task is to stop the ball from crossing the goal line and who is the only player in the team allowed to handle the ball provided, if he is inside his own penalty area.Dictionnaire Français-Anglais (UEFA Football) > gardien de but
-
7 lancer d'objets
Action des spectateurs de jeter des objets sur le terrain, sur les joueurs adverses, sur l'arbitre ou sur les policiers qui est interdite.Projecting objects of any kind from the stands to the pitch by spectators, which is not allowed under prevailing security regulations.Dictionnaire Français-Anglais (UEFA Football) > lancer d'objets
-
8 portier
Joueur chargé de protéger le but de son équipe de manière à ce que le ballon ne franchisse pas la ligne de but et qui peut, pour ce faire, utiliser tout son corps, y compris ses bras et ses mains, dans sa propre surface de réparation, contrairement aux autres joueurs.Player positioned in the goalmouth whose task is to stop the ball from crossing the goal line and who is the only player in the team allowed to handle the ball provided, if he is inside his own penalty area. -
9 banque d'échantillons de l'environnement
банк образцов природных элементов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
environmental specimen bank
Places in which selected specimens (fish, mussels, milk, soil sample and human tissue, etc.) are stored without being allowed to decompose. (Source: AZENP)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > banque d'échantillons de l'environnement
-
10 réserve de biosphčre
биосферный заповедник
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biosphere reserve
Protected land and coastal areas that are approved under the Man and Biosphere programme (MAB) in conjunction with the Convention on International Trade in Endangered Species (CITES). Each reserve has to have an ecosystem that is recognized for its diversity and usefulness as a conservation unit. The reserves have at least one core area where there can be no interference with the natural ecosystem. A transition zone surrounds this and within it scientific research is allowed. Beyond this is a buffer zone which protects the whole reserve from agricultural, industrial and urban development. Biosphere reserves and buffer zones were regarded as examples of a new generation of conservation techniques. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > réserve de biosphčre
-
11 biofiltration
биофильтрация
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biofiltration
The distribution of settled sewage on a bed of inert granular material through which it is allowed to percolate. In doing so, the effluent is aerated thus allowing aerobic bacteria and fungi to reduce its biochemical oxygen demand. (Source: PORT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > biofiltration
-
12 réserve de pęche
водоем для спортивной рыбной ловли
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
fishing preserve
Limited portion of a water body where angling is allowed. (Source: RRDA)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > réserve de pęche
-
13 pręt de document
выдача документов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
document lending
The service provided by a library in which the library's clients are temporarily allowed to use books and other printed materials outside the library. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > pręt de document
-
14 pręt inter-bibliothčques
выдача по межбиблиотечному обмену
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
inter-library loan
The service provided by one library in which a second library's clients are temporarily allowed to use books and other printed materials belonging to the first library; and consequently the system providing rules and infrastructure for this service to a group of libraries. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > pręt inter-bibliothčques
-
15 courant maximal admissible
допустимый длительный ток кабеля (провода)
-
[Интент]
допустимый длительный ток (проводника)
Максимальный электрический ток, который проводник способен проводить в продолжительном режиме без превышения его установившейся температурой определённого значения.
Допустимый длительный ток является одной из основных характеристик проводника. Он представляет собой максимальный электрический ток, который проводник может проводить длительно (неделями, месяцами, годами) не перегреваясь. Значение допустимого длительного тока зависит от сечения проводника, материалов из которых выполнены проводник и его изоляция, способов монтажа проводника в электроустановке здания. Допустимый длительный ток проводника фактически является его номинальным током. В электроустановках зданий выполняют защиту проводников от сверхтоков, протекание которых по проводникам сопровождается их перегревом.
[ http://www.volt-m.ru/glossary/letter/%C4/view/11/]EN
current carrying capacity
maximum current a cable circuit (one or several conductors) can support resulting in a specified increase of the surface temperature of the conductor beyond the ambient temperature, not exceeding the maximum allowed operating temperature of the cable
[IEC 61156-1, ed. 3.0 (2007-06< size="2">)]FR
courant maximal admissible
courant maximal qu’un circuit de câble (un ou plusieurs conducteurs) peut supporter avec une augmentation spécifiée de la température de surface du conducteur au delà de la température ambiante, et ne dépassant pas la température maximale de fonctionnement autorisée du câble
[IEC 61156-1, ed. 3.0 (2007-06< size="2">)]Номинальный ток устройств защиты от короткого замыкания может превышать допустимый длительный ток кабеля.
[ ГОСТ Р 50571. 5-94 ( МЭК 364-4-43-77)]Допустимые длительные токи для проводов и кабелей, проложенных в коробах, а также в лотках пучками, должны приниматься...
[ПУЭ]Тематики
- кабели, провода...
- электроустановки
EN
- ampere capacity
- current carrying capacity
- current carrying capacity of the cable
- current carrying capacity of the conductors
- current-carrying capacity of the cable
FR
Франко-русский словарь нормативно-технической терминологии > courant maximal admissible
-
16 dépôt ancien
заброшенная мусорная яма
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
old landfill site
Landfill that has been filled and covered with topsoil and seeded. The most common end use for landfills is open spaces with no active recreation taking place over the completed landfill. The obvious reason for this use is that the completed surface is steeply sloped to provide rapid runoff. Also, no irrigation of the cover grasses should be allowed. It is very unlikely to think that commercial or industrial buildings will be constructed on a completed landfill. If the end use is such that the public will be walking on the site, it is important that all manholes be properly secured, leachate lagoons fenced, and other potential hazards eliminated. (Source: CORBITa)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > dépôt ancien
-
17 température maximale de service
максимальная допустимая температура
-
[IEV number 442-06-41]EN
maximum permissible temperature
maximum service temperature
Denotes the highest temperature which the connecting device is allowed to attain in normal use as a result of ambient temperature, induced heat, and heat caused by the device itself
[IEV number 442-06-41]FR
température maximale permise
température maximale de service
Température la plus élevée que le dispositif de connexion peut atteindre en usage normal et résultant de la température ambiante, de la chaleur induite et de la chaleur dégagée par le dispositif lui-même
[IEV number 442-06-41]EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > température maximale de service
-
18 température maximale permise
максимальная допустимая температура
-
[IEV number 442-06-41]EN
maximum permissible temperature
maximum service temperature
Denotes the highest temperature which the connecting device is allowed to attain in normal use as a result of ambient temperature, induced heat, and heat caused by the device itself
[IEV number 442-06-41]FR
température maximale permise
température maximale de service
Température la plus élevée que le dispositif de connexion peut atteindre en usage normal et résultant de la température ambiante, de la chaleur induite et de la chaleur dégagée par le dispositif lui-même
[IEV number 442-06-41]EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > température maximale permise
-
19 concentration maximale admissible
максимально допустимая концентрация
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
maximum admissible concentration
The maximum exposure to a physical or chemical agent allowed in an 8-hour work day to prevent disease or injury. (Source: KOREN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
предельно допустимая концентрация примеси в атмосфере
ПДК
Ндп. максимально возможная концентрация
предельная концентрация
Максимальная концентрация примеси в атмосфере, отнесенная к определенному времени осреднения, которая при периодическом воздействии или на протяжении всей жизни человека не оказывает на него вредного действия, включая отдаленные последствия, и на окружающую среду в целом.
[ ГОСТ 17.2.1.04-77]Недопустимые, нерекомендуемые
Тематики
Синонимы
EN
DE
FR
3. Предельно допустимая концентрация примеси в атмосфере
ПДК
Ндп. Максимально возможная концентрация
D. Maximale Imrnissionskonzentration
Е. Maximum permissible concentration
F. Concentration maximale admissible
Максимальная концентрация примеси в атмосфере, отнесенная к определенному времени осреднения, которая при периодическом воздействии или на протяжении всей жизни человека не оказывает на него вредного действия, включая отдаленные последствия, и на окружающую среду в целом
Источник: ГОСТ 17.2.1.04-77: Охрана природы. Атмосфера. Источники и метеорологические факторы загрязнения, промышленные выбросы. Термины и определения оригинал документа
Франко-русский словарь нормативно-технической терминологии > concentration maximale admissible
-
20 réserve nationale de pęche
национальный рыбный заказник
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
national fishing reserve
Limited portion of a water body belonging to the State where angling is allowed. (Source: RRDA)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > réserve nationale de pęche
- 1
- 2
См. также в других словарях:
allowed — I adjective acceptable, accepted, acknowledged, admissible, admitted, allowable, approvable, approved, authorized, certified, chartered, commissioned, conceded, consented, eligible, empowered, endorsed, enfranchised, granted, justified, lawful,… … Law dictionary
allowed — allowed; un·allowed; … English syllables
allowed — (adj.) late 14c., praised; mid 15c., assigned as a due share; late 15c., permitted, pp. adjective from ALLOW (Cf. allow) … Etymology dictionary
Allowed — Allow Al*low , v. t. [imp. & p. p. {Allowed}; p. pr. & vb. n. {Allowing}.] [OE. alouen, OF. alouer, aloer, aluer, F. allouer, fr. LL. allocare to admit as proved, to place, use; confused with OF. aloer, fr. L. allaudare to extol; ad + laudare to… … The Collaborative International Dictionary of English
allowed — /euh lowd /, adj. Physics. involving a change in quantum numbers, permitted by the selection rules: allowed transition. [ALLOW + ED2] * * * … Universalium
allowed claim — a claim of a creditor (or an equity interest) that is approved by the court for satisfaction under the plan of reorganization (Glossary of Common Bankruptcy Terms) (or allowed interest) (Common Bankruptcy Terms) A claim of a creditor (or an… … Glossary of Bankruptcy
allowed interest — a claim of a creditor (or an equity interest) that is approved by the court for satisfaction under the plan of reorganization (Glossary of Common Bankruptcy Terms) (or allowed claim) (Common Bankruptcy Terms) A claim of a creditor (or an equity… … Glossary of Bankruptcy
allowed claim — USA A claim which the court has approved for payment under a plan of reorganization. Practical Law Dictionary. Glossary of UK, US and international legal terms. www.practicallaw.com. 2010 … Law dictionary
Allowed cell rate — The allowed cell rate is the rate in cells per second at which a source device may send data in ATM networks … Wikipedia
allowed him to — permitted him to, allowed him to; made it possible for him to … English contemporary dictionary
allowed outage time — leidžiamoji prastovos trukmė statusas Aprobuotas sritis branduolinė sauga apibrėžtis Maksimalus laikas, kurį leidžiamas saugai svarbios sistemos ar komponento atjungimas arba išjungimas dėl techninės priežiūros, įskaitant remontą. atitikmenys:… … Lithuanian dictionary (lietuvių žodynas)
