a+history+of+reading

SUBJECT AREA: Textiles

[br]

[br]

[br]

In mass production of garments, layers of cloth are laid out on top of each other and multiples of each different part are cut out at the same time. The first portable cutting machine was invented by Joseph Bloch in 1888. It was operated from a DC electricity supply and had a circular knife, which was difficult to use when cutting round curves. Therefore the cloth had to be raised on curves so that it would reach the furthest part of the circular blade. In the same year in the USA, G.P.Eastman produced a vertically reciprocating cutting machine with a straight blade.

[br]

SUBJECT AREA: Textiles

[br]

[br]

[br]

In the earliest draw looms, the pattern to be woven was selected by means of loops of string that were loosely tied round the appropriate leashes, which had to be lifted to make that pick of the pattern by raising the appropriate warp threads. In Isfahan, Persia, looms were seen in the 1970s where a boy sat in the top of the loom. Before the weaver could weave the next pick, the boy selected the appropriate loop of string, pulled out those leashes which were tied in it and lifted them up by means of a forked stick. The weaver below him held up these leashes by a pair of wooden sticks and sent the shuttle through that shed while the boy was sorting out the next loop of string with its leashes. When the pick had been completed, the first loop was dropped further down the leashes and, presumably, when the whole sequence of that pattern was finished, all the loops had be pushed up the leashes to the top of the loom again.

Models in the Conservatoire National des Arts et Métiers, Paris, show that in 1725 Bouchon, a worker in Lyon, dispensed with the loops of string and selected the appropriate leashes by employing a band of pierced paper pressed against a row of horizontal wires by the drawboy using a hand-bar so as to push forward those which happened to lie opposite the blank spaces. These connected with loops at the lower extremity of vertical wires linked to the leashes at the top of the loom. The vertical wires could be pulled down by a comb-like rack beside the drawboy at the side of the loom in order to pull up the appropriate leashes to make the next shed. Bouchon seems to have had only one row of needles or wires, which must have limited the width of the patterns. This is an early form of mechanical memory, used in computers much later. The apparatus was improved subsequently by Falcon and Jacquard.

[br]

SUBJECT AREA: Steam and internal combustion engines

[br]

[br]

[br]

Branca practised architecture at Loretto. In 1629 he published Le Machine: volume nuovo et di molto artificio, in which he described various mechanisms. One was the application of rolls for working copper, lead or the precious metals gold and silver. The rolls were powered by a form of smokejack with the gases from the fire passing up a long tube forming a chimney which, through gearing, turned the rolls. Another device used a jet of steam from a boiler issuing from a mouthpiece shaped like the head of a person to impinge upon blades around the circumference of a horizontal wheel, connected through triple reduction gearing to drop stamps, for pounding drugs. This was a form of impulse turbine and has been claimed as the first machine worked by steam to do a particular operation since Heron's temple doors.

[br]

SUBJECT AREA: Aerospace, Weapons and armour

[br]

[br]

[br]

Von Braun's mother was an amateur astronomer who introduced him to the futuristic books of Jules Verne and H.G.Wells and gave him an astronomical telescope. He was a rather slack and undisciplined schoolboy until he came across Herman Oberth's book By Rocket to Interplanetary Space. He discovered that he required a good deal of mathematics to follow this exhilarating subject and immediately became an enthusiastic student.

The Head of the Ballistics and Armaments branch of the German Army, Professor Karl Becker, had asked the engineer Walter Dornberger to develop a solid-fuel rocket system for short-range attack, and one using liquid-fuel rockets to carry bigger loads of explosives beyond the range of any known gun. Von Braun joined the Verein für Raumschiffsfahrt (the German Space Society) as a young man and soon became a leading member. He was asked by Rudolf Nebel, VfR's chief, to persuade the army of the value of rockets as weapons. Von Braun wisely avoided all mention of the possibility of space flight and some financial backing was assured. Dornberger in 1932 built a small test stand for liquid-fuel rockets and von Braun built a small rocket to test it; the success of this trial won over Dornberger to space rocketry.

Initially research was carried out at Kummersdorf, a suburb of Berlin, but it was decided that this was not a suitable site. Von Braun recalled holidays as a boy at a resort on the Baltic, Peenemünde, which was ideally suited to rocket testing. Work started there but was not completed until August 1939, when the group of eighty engineers and scientists moved in. A great fillip to rocket research was received when Hitler was shown a film and was persuaded of the efficacy of rockets as weapons of war. A factory was set up in excavated tunnels at Mittelwerk in the Harz mountains. Around 6,000 "vengeance" weapons were built, some 3,000 of which were fired on targets in Britain and 2,000 of which were still in storage at the end of the Second World War.

Peenemünde was taken by the Russians on 5 May 1945, but by then von Braun was lodging with many of his colleagues at an inn, Haus Ingeburg, near Oberjoch. They gave themselves up to the Americans, and von Braun presented a "prospectus" to the Americans, pointing out how useful the German rocket team could be. In "Operation Paperclip" some 100 of the team were moved to the United States, together with tons of drawings and a number of rocket missiles. Von Braun worked from 1946 at the White Sands Proving Ground, New Mexico, and in 1950 moved to Redstone Arsenal, Huntsville, Alabama. In 1953 he produced the Redstone missile, in effect a V2 adapted to carry a nuclear warhead a distance of 320 km (199 miles). The National Aeronautics and Space Administration (NASA) was formed in 1958 and recruited von Braun and his team. He was responsible for the design of the Redstone launch vehicles which launched the first US satellite, Explorer 1, in 1958, and the Mercury capsules of the US manned spaceflight programme which carried Alan Shepard briefly into space in 1961 and John Glenn into earth orbit in 1962. He was also responsible for the Saturn series of large, staged launch vehicles, which culminated in the Saturn V rocket which launched the Apollo missions taking US astronauts for the first human landing on the moon in 1969. Von Braun announced his resignation from NASA in 1972 and died five years later.

[br]

SUBJECT AREA: Agricultural and food technology, Textiles

[br]

[br]

[br]

Edmund Cartwright, the fourth son of William Cartwright, was educated at Wakefield Grammar School, and went to University College, Oxford, at the age of 14. By special act of convocation in 1764, he was elected Fellow of Magdalen College. He married Alice Whitaker in 1772 and soon after was given the ecclesiastical living of Brampton in Derbyshire. In 1779 he was presented with the living of Goadby, Marwood, Leicestershire, where he wrote poems, reviewed new works, and began agricultural experiments. A visit to Matlock in the summer of 1784 introduced him to the inventions of Richard Arkwright and he asked why weaving could not be mechanized in a similar manner to spinning. This began a remarkable career of inventions.

Cartwright returned home and built a loom which required two strong men to operate it. This was the first attempt in England to develop a power loom. It had a vertical warp, the reed fell with the weight of at least half a hundredweight and, to quote Gartwright's own words, "the springs which threw the shuttle were strong enough to throw a Congreive [sic] rocket" (Strickland 19.71:8—for background to the "rocket" comparison, see Congreve, Sir William). Nevertheless, it had the same three basics of weaving that still remain today in modern power looms: shedding or dividing the warp; picking or projecting the shuttle with the weft; and beating that pick of weft into place with a reed. This loom he proudly patented in 1785, and then he went to look at hand looms and was surprised to see how simply they operated. Further improvements to his own loom, covered by two more patents in 1786 and 1787, produced a machine with the more conventional horizontal layout that showed promise; however, the Manchester merchants whom he visited were not interested. He patented more improvements in 1788 as a result of the experience gained in 1786 through establishing a factory at Doncaster with power looms worked by a bull that were the ancestors of modern ones. Twenty-four looms driven by steam-power were installed in Manchester in 1791, but the mill was burned down and no one repeated the experiment. The Doncaster mill was sold in 1793, Cartwright having lost £30,000, However, in 1809 Parliament voted him £10,000 because his looms were then coming into general use.

In 1789 he began working on a wool-combing machine which he patented in 1790, with further improvements in 1792. This seems to have been the earliest instance of mechanized combing. It used a circular revolving comb from which the long fibres or "top" were. carried off into a can, and a smaller cylinder-comb for teasing out short fibres or "noils", which were taken off by hand. Its output equalled that of twenty hand combers, but it was only relatively successful. It was employed in various Leicestershire and Yorkshire mills, but infringements were frequent and costly to resist. The patent was prolonged for fourteen years after 1801, but even then Cartwright did not make any profit. His 1792 patent also included a machine to make ropes with the outstanding and basic invention of the "cordelier" which he communicated to his friends, including Robert Fulton, but again it brought little financial benefit. As a result of these problems and the lack of remuneration for his inventions, Cartwright moved to London in 1796 and for a time lived in a house built with geometrical bricks of his own design.

Other inventions followed fast, including a tread-wheel for cranes, metallic packing for pistons in steam-engines, and bread-making and brick-making machines, to mention but a few. He had already returned to agricultural improvements and he put forward suggestions in 1793 for a reaping machine. In 1801 he received a prize from the Board of Agriculture for an essay on husbandry, which was followed in 1803 by a silver medal for the invention of a three-furrow plough and in 1805 by a gold medal for his essay on manures. From 1801 to 1807 he ran an experimental farm on the Duke of Bedford's estates at Woburn.

From 1786 until his death he was a prebendary of Lincoln. In about 1810 he bought a small farm at Hollanden near Sevenoaks, Kent, where he continued his inventions, both agricultural and general. Inventing to the last, he died at Hastings and was buried in Battle church.

[br]

SUBJECT AREA: Photography, film and optics

[br]

[br]

[br]

The son of a minor official in a magistrate's court, Daguerre showed an early aptitude for drawing. He was first apprenticed to an architect, but in 1804 he moved to Paris to learn the art of stage design. He was particularly interested in perspective and lighting, and later showed great ingenuity in lighting stage sets. Fascinated by a popular form of entertainment of the period, the panorama, he went on to create a variant of it called the diorama. It is assumed that he used a camera obscura for perspective drawings and, by purchasing it from the optician Chevalier, he made contact with Joseph Nicéphore Niepce. In 1829 Niepce and Daguerre entered into a formal partnership to perfect Niepce's heliographic process, but the partnership was dissolved when Niepce died in 1833, when only limited progress had been made. Daguerre continued experimenting alone, however, using iodine and silver plates; by 1837 he had discovered that images formed in the camera obscura could be developed by mercury vapour and fixed with a hot salt solution. After unsuccessfully attempting to sell his process, Daguerre approached F.J.D. Arago, of the Académie des Sciences, who announced the discovery in 1839. Details of Daguerre's work were not published until August of that year when the process was presented free to the world, except England. With considerable business acumen, Daguerre had quietly patented the process through an agent, Miles Berry, in London a few days earlier. He also granted a monopoly to make and sell his camera to a Monsieur Giroux, a stationer by trade who happened to be a relation of Daguerre's wife. The daguerreotype process caused a sensation when announced. Daguerre was granted a pension by a grateful government and honours were showered upon him all over the world. It was a direct positive process on silvered copper plates and, in fact, proved to be a technological dead end. The future was to lie with negative-positive photography devised by Daguerre's British contemporary, W.H.F. Talbot, although Daguerre's was the first practicable photographic process to be announced. It captured the public's imagination and in an improved form was to dominate professional photographic practice for more than a decade.

[br]

SUBJECT AREA: Electricity

[br]

[br]

[br]

With an early bias towards science, Daniell's interest in chemistry was formed when he joined a relative's sugar-refining business. He formed a lifelong friendship with W.T.Brande, Professor of Chemistry at the Royal Institution, and together they revived the journal of the Royal Institution, to which Daniell submitted many of his early papers on chemical subjects. He made many contributions to the science of meteorology and in 1820 invented a hydrometer, which became widely used and gave precision to the measurement of atmospheric moisture. As one of the originators of the Society for Promoting Useful Knowledge, Daniell edited several of its early publications. His work on crystallization established his reputation as a chemist and in 1831 he was appointed the first Professor of Chemistry at King's College, London, where he was largely responsible for establishing its department of applied science. He was also involved in the Chemical Society of London and served as its Vice-President. At King's College he began the research into current electricity with which his name is particularly associated. His investigations into the zinc-copper cell revealed that the rapid decline in power was due to hydrogen gas being liberated at the positive electrode. Daniell's cell, invented in 1836, employed a zinc electrode in dilute sulphuric acid and a copper electrode in a solution of copper sulphate, the electrodes being separated by a porous membrane, typically an unglazed earthenware pot. He was awarded the Copley Medal of the Royal Society for his invention which avoided the "polarization" of the simple cell and provided a further source of current for electrical research and for commercial applications such as electroplating. Although the high internal resistance of the Daniell cell limited the current and the potential was only 1.1 volts, the voltage was so unchanging that it was used as a reference standard until the 1870s, when J. Lattimer Clark devised an even more stable cell.

[br]

SUBJECT AREA: Electricity, Land transport, Railways and locomotives

[br]

[br]

[br]

Davidson, son of an Aberdeen merchant, attended Marischal College, Aberdeen, between 1819 and 1822: his studies included mathematics, mechanics and chemistry. He subsequently joined his father's grocery business, which from time to time received enquiries for yeast: to meet these, Davidson began to manufacture yeast for sale and from that start built up a successful chemical manufacturing business with the emphasis on yeast and dyes. About 1837 he started to experiment first with electric batteries and then with motors. He invented a form of electromagnetic engine in which soft iron bars arranged on the periphery of a wooden cylinder, parallel to its axis, around which the cylinder could rotate, were attracted by fixed electromagnets. These were energized in turn by current controlled by a simple commutaring device. Electric current was produced by his batteries. His activities were brought to the attention of Michael Faraday and to the scientific world in general by a letter from Professor Forbes of King's College, Aberdeen. Davidson declined to patent his inventions, believing that all should be able freely to draw advantage from them, and in order to afford an opportunity for all interested parties to inspect them an exhibition was held at 36 Union Street, Aberdeen, in October 1840 to demonstrate his "apparatus actuated by electro-magnetic power". It included: a model locomotive carriage, large enough to carry two people, that ran on a railway; a turning lathe with tools for visitors to use; and a small printing machine. In the spring of 1842 he put on a similar exhibition in Edinburgh, this time including a sawmill. Davidson sought support from railway companies for further experiments and the construction of an electromagnetic locomotive; the Edinburgh exhibition successfully attracted the attention of the proprietors of the Edinburgh 585\& Glasgow Railway (E \& GR), whose line had been opened in February 1842. Davidson built a full-size locomotive incorporating his principle, apparently at the expense of the railway company. The locomotive weighed 7 tons: each of its two axles carried a cylinder upon which were fastened three iron bars, and four electromagnets were arranged in pairs on each side of the cylinders. The motors he used were reluctance motors, the power source being zinc-iron batteries. It was named Galvani and was demonstrated on the E \& GR that autumn, when it achieved a speed of 4 mph (6.4 km/h) while hauling a load of 6 tons over a distance of 1 1/2 miles (2.4 km); it was the first electric locomotive. Nevertheless, further support from the railway company was not forthcoming, although to some railway workers the locomotive seems to have appeared promising enough: they destroyed it in Luddite reaction. Davidson staged a further exhibition in London in 1843 without result and then, the cost of battery chemicals being high, ceased further experiments of this type. He survived long enough to see the electric railway become truly practicable in the 1880s.

[br]

PJGR / GW

SUBJECT AREA: Textiles

[br]

[br]

[br]

William Dawson, a Leicester framework knitter, made an important addition to William Lee's knitting machine with his invention of the notched wheel in 1791. Lee's machine could make only plain knitting; to be able to knit patterns, there had to be some means of mechanically selecting and operating, independently of all the others, any individual thread, needle, lever or bar at work in the machine. This was partly achieved when Dawson devised a wheel that was irregularly notched on its edge and which, when rotated, pushed sprung bars, which in turn operated on the needles or other parts of the recently invented warp knitting machines. He seems to have first applied the idea for the knitting of military sashes, but then found it could be adapted to plait stay laces with great rapidity. With the financial assistance of two Leicester manufacturers and with his own good mechanical ability, Dawson found a way of cutting his wheels. However, the two financiers withdrew their support because he did not finish the design on time, although he was able to find a friend in a Nottingham architect, Mr Gregory, who helped him to obtain the patent. A number of his machines were set up in Nottingham but, like many other geniuses, he squandered his money away. When the patent expired, he asked Lord Chancellor Eldon to have it renewed: he moved his workshop to London, where Eldon inspected his machine, but the patent was not extended and in consequence Dawson committed suicide.

[br]

SUBJECT AREA: Aerospace

[br]

[br]

[br]

Geoffrey de Havilland started experimenting with aircraft and engines of his own design in 1908. In the following year, with the help of his friend Frank Hearle, he built and flew his first aircraft; it crashed on its first flight. The second aircraft used the same engine and made its first flight on 10 September 1910, and enabled de Havilland to teach himself to fly. From 1910 to 1914 he was employed at Farnborough, where in 1912 the Royal Aircraft Factory was established. As Chief Designer and Chief Test Pilot he was responsible for the BE 2, which was the first British military aircraft to land in France in 1914.

In May 1914 de Havilland went to work for George Holt Thomas, whose Aircraft Manufacturing Company Ltd (Airco) of Hendon was expanding to design and build aircraft of its own design. However, because de Havilland was a member of the Royal Flying Corps Reserve, he had to report for duty when war broke out in August. His value as a designer was recognized and he was transferred back to Airco, where he designed eight aircraft in four years. Of these, the DH 2, DH 4, DH 5, DH 6 and DH 9 were produced in large numbers, and a modified DH 4A operated the first British cross- Channel air service in 1919.

On 25 September 1920 de Havilland founded his own company, the De Havilland Aircraft Company Ltd, at Stag Lane near Edgware, London. During the 1920s and 1930s de Havilland concentrated on civil aircraft and produced the very successful Moth series of small biplanes and monoplanes, as well as the Dragon, Dragon Rapide, Albatross and Flamingo airliners. In 1930 a new site was acquired at Hatfield, Hertfordshire, and by 1934 a modern factory with a large airfield had been established. His Comet racer won the England-Australia air race in 1934 using de Havilland engines. By this time the company had established very successful engine and propeller divisions. The Comet used a wooden stressed-skin construction which de Havilland developed and used for one of the outstanding aircraft of the Second World War: the Mosquito. The de Havilland Engine Company started work on jet engines in 1941 and their Goblin engine powered the Vampire jet fighter first flown by Geoffrey de Havilland Jr in 1943. Unfortunately, Geoffrey Jr and his brother John were both killed in flying accidents. The Comet jet airliner first flew in 1949 and the Trident in 1962, although by 1959 the De Havilland Company had been absorbed into Hawker Siddeley Aviation.

[br]

SUBJECT AREA: Textiles

[br]

[br]

[br]

Robert Kay improved his father John's flying shuttle by inventing the drop box, in which up to four shuttles could be stored one below the other. The weaver's left hand controlled levers and catches to raise or lower the drop box in order to bring the appropriate shuttle into line with the shuttle race on the slay. The shuttle could then be driven across the loom, leaving its particular type or colour of weft. On the earliest power looms of Edmund Cartwright in 1785, and for many years later, it was possible to use only one shuttle. In 1845 Squire Diggle of Bury, Lancashire, took out a patent for mechanizing the drop box so that different types or colours of weft could be woven without the weaver attending to the shuttles. He used an endless chain on which plates of different heights could be fixed to raise the boxes to the required height; later this would be operated by either the dobby or Jacquard pattern-selecting mechanisms. He took out further patents for improvements to looms. One, in 1854, was for taking up the cloth with a positive motion. Two more, in 1858, improved his drop box mechanism: the first was for actually operating the drop box, while the second was for tappet chains which operated the timing for raising the boxes.

[br]

See also: Kay, John

SUBJECT AREA: Horology

[br]

[br]

[br]

Giovanni was the son of Jacopo de'Dondi dall'-Orologio, a physician who designed a public clock that was installed in Padua in 1344. The careers of both father and son followed similar paths, for Giovanni became Physician to Emperor Charles IV and designed a complicated astronomical clock (astrarium) for which he became famous. Around 1350 he was appointed Professor of Astronomy at the University of Padua. Dondi completed his astrarium in 1381, having worked on it for sixteen years. Unlike the clock of Richard of Wallingford, it used the common form of verge escapement and had no facility for sounding the hours on a bell. It did, however, indicate time on a 24- hour dial and had calendars for both the fixed and movable feasts of the Church. Its principal function was to show the motions of the planets on the Ptolemaic theory, i.e. the Sun, Moon, Mercury, Venus, Mars, Jupiter and Saturn. Like the Wallingford clock, it also indicated the position of the nodes, or points where the orbits of the Sun and Moon intersected, so that eclipses could be predicted. The astrarium was acquired by the Duke of Milan and its history can be traced to c.1530, when it was in disrepair. It is now known only from copies of Dondi's manuscript "Tractus astarii". Several modern reconstructions have been made based upon the details in the various manuscripts.

[br]

SUBJECT AREA: Aerospace

[br]

[br]

[br]

In 1912 Donald Douglas went to the Massachusetts Institute of Technology to study aeronautical engineering. After graduating in this relatively new subject he joined the Glenn L.Martin Company as Chief Engineer. In 1920 he founded the Davis-Douglas Company in California to build an aircraft capable of flying across America non-stop: unfortunately, the Cloudster failed to achieve its target. Douglas reorganized the company in 1921 as the Douglas Company (later it became the Douglas Aircraft Company). In 1924 a team of US Army personnel made the first round-the-world flight in specially designed Douglas World Cruisers, a feat which boosted Douglas's reputation considerably. This reputation was further enhanced by his airliner, designed in 1935, that revolutionized air travel: the Douglas Commercial 3, or DC-3, of which some 13,000 were built. A series of piston-engined airliners followed, culminating in the DC-7. Meanwhile, in the military field, Douglas aircraft played a major part in the Second World War. In the jet age Douglas continued to produce a wide range of successful civil and military aircraft, and the company also moved into the rocket and guided missile business. In 1966 Donald W. Douglas was still Chairman of the company, with Donald W.Douglas Jr as President. In 1967 the company merged with the McDonnell Aircraft Company to become the giant McDonnell Douglas Corporation.

[br]

SUBJECT AREA: Photography, film and optics

[br]

[br]

[br]

The son of a tax collector, Ducos du Hauron began researches into colour photography soon after the publication of Clerk Maxwell's experiment in 1861. In a communication sent in 1862 for presentation at the Académie des Sciences, but which was never read, he outlined a number of methods for photography of colours. Subsequently, in his book Les Couleurs en photographie, published in 1869, he outlined most of the principles of additive and subtractive colour photography that were later actually used. He covered additive processes, developed from Clerk Maxwell's demonstrations, and subtractive processes which could yield prints. At the time, the photographic materials available prevented the processes from being employed effectively. The design of his Chromoscope, in which transparent reflectors could be used to superimpose three additive images, was sound, however, and formed the basis of a number of later devices. He also proposed an additive system based on the use of a screen of fine red, yellow and blue lines, through which the photograph was taken and viewed. The lines blended additively when seen from a certain distance. Many years later, in 1907, Ducos du Hauron was to use this principle in an early commercial screen-plate process, Omnicolore. With his brother Alcide, he published a further work in 1878, Photographie des Couleurs, which described some more-practical subtractive processes. A few prints made at this time still survive and they are remarkably good for the period. In a French patent of 1895 he described yet another method for colour photography. His "polyfolium chromodialytique" involved a multiple-layer package of separate red-, green-and blue-sensitive materials and filters, which with a single exposure would analyse the scene in terms of the three primary colours. The individual layers would be separated for subsequent processing and printing. In a refined form, this is the principle behind modern colour films. In 1891 he patented and demonstrated the anaglyph method of stereoscopy, using superimposed red and green left and right eye images viewed through green and red filters. Ducos du Hauron's remarkable achievement was to propose theories of virtually all the basic methods of colour photography at a time when photographic materials were not adequate for the purpose of proving them correct. For his work on colour photography he was awarded the Progress Medal of the Royal Photographic Society in 1900, but despite his major contributions to colour photography he remained in poverty for much of his later life.

[br]

SUBJECT AREA: Metallurgy

[br]

[br]

[br]

A descendant of Nuremberg nobility, Ebener became recognized as a statesman in his native city and was employed also by foreign dignitaries. His appointment as Privy Councillor to the Dukes of Brunswick involved him in mining and metallurgical affairs at the great Rammelsberg mixed-ore mine at Goslar in the Harz mountains. About 1550, at Rammelsberg, Ebener is believed to have made brass by incorporating accretions of zinc formed in crevices of local lead-smelting furnaces. This small-scale production of impure zinc, formerly discarded as waste, could be used to replace calamine, the carbonate ore of zinc, which by tradition had been combined with copper in European brassmaking. Ercker, writing in 1574, mentions the accretions at Goslar obtained by removing furnace sections to make this material available for brass. The true nature of the zinc ore, calamine, and zinc metal compared with these accretions was determined only much later, but variation in quality with respect to impurities made the material most suitable for cast brassware rather than beaten goods. As quantities were small and much valued, distribution from Goslar was limited, not normally reaching Britain, where production of brasses continued to rely on calamine or expensive zinc imports from the East. Rammelsberg profited from the waste material accumulating over the years and its use at Bundheim brassworks east of Goslar. Ebener partnered Duke Henry the Younger of Brunswick in financing a new drainage adit at Rammelsberg, and was later granted several iron mines and smelting works. From 1556 he was granted rights to market calamine from the Lower Harz and copper sulphate from Rammelsberg. Ebener later had an important role at the court of Duke Julius, son of Henry, advising him on the founding of Helmstedt University.

[br]

SUBJECT AREA: Ports and shipping, Steam and internal combustion engines

[br]

[br]

[br]

John was the third son of David Elder. The father came from a family of millwrights and moved to Glasgow where he worked for the well-known shipbuilding firm of Napier's and was involved with improving marine engines. John was educated at Glasgow High School and then for a while at the Department of Civil Engineering at Glasgow University, where he showed great aptitude for mathematics and drawing. He spent five years as an apprentice under Robert Napier followed by two short periods of activity as a pattern-maker first and then a draughtsman in England. He returned to Scotland in 1849 to become Chief Draughtsman to Napier, but in 1852 he left to become a partner with the Glasgow general engineering company of Randolph Elliott \& Co. Shortly after his induction (at the age of 28), the engineering firm was renamed Randolph Elder \& Co.; in 1868, when the partnership expired, it became known as John Elder \& Co. From the outset Elder, with his partner, Charles Randolph, approached mechanical (especially heat) engineering in a rigorous manner. Their knowledge and understanding of entropy ensured that engine design was not a hit-and-miss affair, but one governed by recognition of the importance of the new kinetic theory of heat and with it a proper understanding of thermodynamic principles, and by systematic development. In this Elder was joined by W.J.M. Rankine, Professor of Civil Engineering and Mechanics at Glasgow University, who helped him develop the compound marine engine. Elder and Randolph built up a series of patents, which guaranteed their company's commercial success and enabled them for a while to be the sole suppliers of compound steam reciprocating machinery. Their first such engine at sea was fitted in 1854 on the SS Brandon for the Limerick Steamship Company; the ship showed an improved performance by using a third less coal, which he was able to reduce still further on later designs.

Elder developed steam jacketing and recognized that, with higher pressures, triple-expansion types would be even more economical. In 1862 he patented a design of quadruple-expansion engine with reheat between cylinders and advocated the importance of balancing reciprocating parts. The effect of his improvements was to greatly reduce fuel consumption so that long sea voyages became an economic reality.

His yard soon reached dimensions then unequalled on the Clyde where he employed over 4,000 workers; Elder also was always interested in the social welfare of his labour force. In 1860 the engine shops were moved to the Govan Old Shipyard, and again in 1864 to the Fairfield Shipyard, about 1 mile (1.6 km) west on the south bank of the Clyde. At Fairfield, shipbuilding was commenced, and with the patents for compounding secure, much business was placed for many years by shipowners serving long-distance trades such as South America; the Pacific Steam Navigation Company took up his ideas for their ships. In later years the yard became known as the Fairfield Shipbuilding and Engineering Company Ltd, but it remains today as one of Britain's most efficient shipyards and is known now as Kvaerner Govan Ltd.

In 1869, at the age of only 45, John Elder was unanimously elected President of the Institution of Engineers and Shipbuilders in Scotland; however, before taking office and giving his eagerly awaited presidential address, he died in London from liver disease. A large multitude attended his funeral and all the engineering shops were silent as his body, which had been brought back from London to Glasgow, was carried to its resting place. In 1857 Elder had married Isabella Ure, and on his death he left her a considerable fortune, which she used generously for Govan, for Glasgow and especially the University. In 1883 she endowed the world's first Chair of Naval Architecture at the University of Glasgow, an act which was reciprocated in 1901 when the University awarded her an LLD on the occasion of its 450th anniversary.

[br]

RLH / FMW

SUBJECT AREA: Broadcasting, Electronics and information technology, Telecommunications

[br]

[br]

[br]

Whilst still in high school, Farnsworth became interested in the possibility of television and conceived many of the basic features of a practicable system of TV broadcast and reception. Following two years of study at the Brigham Young University in Provo, Utah, in 1926 he cofounded the Crocker Research Laboratories in San Francisco, subsequently Farnsworth Television Inc. (1929) and Farnsworth Radio \& Television Corporation, Fort Wayne, Indiana (1938). There he began a lifetime of research, primarily in the field of television. In 1927, with the backing of the Radio Corporation of America (RCA) and the collaboration of Vladimir Zworykin, he demonstrated the first all-electronic television system, based on his early ideas for an image dissector tube, the first electronic equivalent of the Nipkow disc. With this rudimentary sixty-line system he was able to transmit a recognizable dollar sign and file the first of many TV patents. From then on he contributed to a variety of developments in the fields of vacuum tubes, radar and atomic-power generation, with patents on cathode ray tubes, amplifying and pick-up tubes, electron multipliers and photoelectric materials.

[br]

See also: Baird, John Logie; Jenkins, Charles Francis

SUBJECT AREA: Electronics and information technology

[br]

[br]

[br]

Born on a cattle ranch, Forrester obtained a BSc in electrical engineering at the University of Nebraska in 1939 and his MSc at the Massachusetts Institute of Technology (MIT) in Cambridge, Massachusetts, where he remained to teach and carry out research. Becoming interested in computing, he established the Digital Computer Laboratory at MIT in 1945 and became involved in the construction of Whirlwind I, an early general-purpose computer completed in March 1951 and used for flight-simulation by the US Army Air Force. Finding the linear memories then available for storing data a major limiting factor in the speed at which computers were able to operate, he developed a three-dimensional store based on the binary switching of the state of small magnetic cores that could be addressed and switched by a matrix of wires carrying pulses of current. The machine used parallel synchronous fixed-point computing, with fifteen binary digits and a plus sign, i.e. 16 bits in all, and contained 5,000 vacuum tubes, eleven semiconductors and a 2 MHz clock for the arithmetic logic unit. It occupied a two-storey building and consumed 150kW of electricity. From his experience with the development and use of computers, he came to realize their great potential for the simulation and modelling of real situations and hence for the solution of a variety of management problems, using data communications and the technique now known as interactive graphics. His later career was therefore in this field, first at the MIT Lincoln Laboratory in Lexington, Massachusetts (1951) and subsequently (from 1956) as Professor at the Sloan School of Management at the Massachusetts Institute of Technology.

[br]

See also: Burks, Arthur Walter; Goldstine, Herman H.; Wilkes, Maurice Vincent; Williams, Sir Frederic Calland

SUBJECT AREA: Mechanical, pneumatic and hydraulic engineering

[br]

[br]

[br]

Very little is known about the life of James Fox, but according to Samuel Smiles (1863) he was as a young man a butler in the service of the Reverend Thomas Gisborne of Foxhall Lodge, Staffordshire. His mechanical abilities were evident from his spare-time activities in the handling of tools and so impressed his employer that he supplied the capital to enable Fox to set up a business in Derby for the manufacture of machinery for the textile and lacemaking industries. To construct this machinery, Fox had to build his own machine tools and later, in the early nineteenth century, made them for sale, some being exported to France, Germany and Poland. He was renowned for his lathes, some of which were quite large; one built in 1830 has been preserved and is 22 ft (6.7 m) long with a swing of 27 in. (69 cm). He was responsible for many improve-ments in the design of the lathe and he also built some of the earliest planing machines (the first, it has been claimed, as early as 1814) and a gear-cutting machine, although this was apparently for cutting wooden patterns for cast gears. The business was continued by his sons Joseph and James (who died in 1859 aged 69) and into the 1860s by the sons of Joseph.

[br]

SUBJECT AREA: Architecture and building, Civil engineering

[br]

[br]

[br]

As early as 1807 Frost, who was originally a builder and bricklayer in Finchley in north London, was manufacturing Roman Cement, patented by James Parker in 1796, in the Harwich area and a similar cement further south, at Sheerness. In the early 1820s Frost visited Louis J.Vicat (1796–1861) in France. Vicat was a French engineer who began in 1812 a detailed investigation into the properties of various limestones found in France. He later published his conclusions, which were that the best hydraulic lime was that produced from limestone containing clay incorporating silica and alumina. He experimented with adding different clays in varying proportions to slaked lime and calcined the mixture. Benefiting from Vicat's research, Frost obtained a patent in 1822 for what he called British Cement. This patent specified an artificial cement made from limestone and silica, and he calcined chalk with the clay to produce a quick-setting product. This was made at Swanscombe near Northfleet on the south bank of the River Thames. In 1833 the Swanscombe manufactory was purchased by Francis \& White for £3,500 and Frost emigrated to America, setting up practice as a civil engineer in New York. The cement was utilized by Sir Marc Brunel in 1835 in his construction of the Thames Tunnel, and at the same time it was used in building the first all-concrete house at Swanscombe for Mr White.

[br]