-
1 power center
главный распределительный щит (ГРЩ)
Распределительный щит, через который снабжается электроэнергией все здание или его обособленная часть. Роль ГРЩ может выполнять ВРУ или щит низкого напряжения подстанции.
[ПУЭ]
главный распределительный щит
Электрощит в здании, обеспечивающий распределение энергии между подключенными к нему нагрузками и включение аварийных систем при падении напряжения.
[ ГОСТ Р 51321. 3-99 ( МЭК 60439-3-90)]
[ ГОСТ Р 50571.28-2006]EN
main distribution board
board in the building which fulfils all the functions of a main electrical distribution for the supply building area assigned to it and where the voltage drop is measured for operating the safety services
[IEC 60364-7-710, ed. 1.0 (2002-11)]FR
tableau général de distribution
tableau de distribution dans le bâtiment remplissant toutes les fonctions d’un tableau général de distribution pour l’alimentation de la zone qui lui est dédiée et où la chute de tension est mesurée pour le fonctionnement des services de sécurité
[IEC 60364-7-710, ed. 1.0 (2002-11)]
Главный распределительный щит (ГРЩ) на ток 6300 А
[http://www.uzoelectro.ru/catalogue/group-383/product-36465/ ]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
- электроустановки
Синонимы
EN
- feeder switchboard
- m.s.b.
- main distributing frame
- main distribution board
- main distribution switchboard
- Main Low Voltage Switchboard
- main low-voltage distribution switchboard
- main switchboard
- MLVS
- MSB
- power center
FR
комплектное устройство первичного распределения электроэнергии
-
[Интент]
Рис. ABBПараллельные тексты EN-RU
They are usually installed on the load side of MV/LV transformers or generators.
These assemblies include one or more incoming units, bus ties and a relatively reduced number of outgoing units.
There are also present measuring instruments and other switching and control equipment.
These assemblies have a sturdy structure to withstand the electrodynamic stresses and the weight of big sized apparatus.
As a matter of fact peculiar characteristics of the power center are high rated currents and shortcircuit currents.
The constructional type is a cubicle structure, with metal enclosure and sections divided into compartments with selective access.
[ABB]Такие устройства обычно подключают на стороне нагрузки СВ/НВ трансформаторов или генераторов.
В их состав входят один или несколько блоков ввода, шины и относительно небольшое число блоков вывода.
В состав комплектного устройства первичного распределения электроэнергии входят также измерительные приборы, коммутационные устройства и средства контроля состояния.
Данные комплектные устройства имеют прочную конструкцию, способную выдерживать электродинамическое действие токов и вес крупногабаритной аппаратуры.
Центры распределения электроэнергии характеризуются высокими номинальным током и током короткого замыкания.
С точки зрения конструктивного исполнения они представляют собой многошкафное комплектное устройство в металлической оболочке, состоящее из секций, каждая из которых разделена на отсеки с независимым доступом.
[Перевод Интент]Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
- комплектное распред. устройство (КРУ)
EN
Англо-русский словарь нормативно-технической терминологии > power center
-
2 primary distribution switchgear
комплектное устройство первичного распределения электроэнергии
-
[Интент]
Рис. ABBПараллельные тексты EN-RU
They are usually installed on the load side of MV/LV transformers or generators.
These assemblies include one or more incoming units, bus ties and a relatively reduced number of outgoing units.
There are also present measuring instruments and other switching and control equipment.
These assemblies have a sturdy structure to withstand the electrodynamic stresses and the weight of big sized apparatus.
As a matter of fact peculiar characteristics of the power center are high rated currents and shortcircuit currents.
The constructional type is a cubicle structure, with metal enclosure and sections divided into compartments with selective access.
[ABB]Такие устройства обычно подключают на стороне нагрузки СВ/НВ трансформаторов или генераторов.
В их состав входят один или несколько блоков ввода, шины и относительно небольшое число блоков вывода.
В состав комплектного устройства первичного распределения электроэнергии входят также измерительные приборы, коммутационные устройства и средства контроля состояния.
Данные комплектные устройства имеют прочную конструкцию, способную выдерживать электродинамическое действие токов и вес крупногабаритной аппаратуры.
Центры распределения электроэнергии характеризуются высокими номинальным током и током короткого замыкания.
С точки зрения конструктивного исполнения они представляют собой многошкафное комплектное устройство в металлической оболочке, состоящее из секций, каждая из которых разделена на отсеки с независимым доступом.
[Перевод Интент]Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
- комплектное распред. устройство (КРУ)
EN
Англо-русский словарь нормативно-технической терминологии > primary distribution switchgear
-
3 primary unit substation
комплектное устройство первичного распределения электроэнергии
-
[Интент]
Рис. ABBПараллельные тексты EN-RU
They are usually installed on the load side of MV/LV transformers or generators.
These assemblies include one or more incoming units, bus ties and a relatively reduced number of outgoing units.
There are also present measuring instruments and other switching and control equipment.
These assemblies have a sturdy structure to withstand the electrodynamic stresses and the weight of big sized apparatus.
As a matter of fact peculiar characteristics of the power center are high rated currents and shortcircuit currents.
The constructional type is a cubicle structure, with metal enclosure and sections divided into compartments with selective access.
[ABB]Такие устройства обычно подключают на стороне нагрузки СВ/НВ трансформаторов или генераторов.
В их состав входят один или несколько блоков ввода, шины и относительно небольшое число блоков вывода.
В состав комплектного устройства первичного распределения электроэнергии входят также измерительные приборы, коммутационные устройства и средства контроля состояния.
Данные комплектные устройства имеют прочную конструкцию, способную выдерживать электродинамическое действие токов и вес крупногабаритной аппаратуры.
Центры распределения электроэнергии характеризуются высокими номинальным током и током короткого замыкания.
С точки зрения конструктивного исполнения они представляют собой многошкафное комплектное устройство в металлической оболочке, состоящее из секций, каждая из которых разделена на отсеки с независимым доступом.
[Перевод Интент]Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
- комплектное распред. устройство (КРУ)
EN
Англо-русский словарь нормативно-технической терминологии > primary unit substation
Перевод: со всех языков на русский
с русского на все языки- С русского на:
- Все языки
- Со всех языков на:
- Все языки
- Английский
- Русский