-
1 длительный
long, de longue durée; de longue haleine (тк. со словами affaire и ouvrage) -
2 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
3 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
4 longue
-
5 de longue durée
длительныйдолговечныйдолговременный -
6 courant maximal admissible
допустимый длительный ток кабеля (провода)
-
[Интент]
допустимый длительный ток (проводника)
Максимальный электрический ток, который проводник способен проводить в продолжительном режиме без превышения его установившейся температурой определённого значения.
Допустимый длительный ток является одной из основных характеристик проводника. Он представляет собой максимальный электрический ток, который проводник может проводить длительно (неделями, месяцами, годами) не перегреваясь. Значение допустимого длительного тока зависит от сечения проводника, материалов из которых выполнены проводник и его изоляция, способов монтажа проводника в электроустановке здания. Допустимый длительный ток проводника фактически является его номинальным током. В электроустановках зданий выполняют защиту проводников от сверхтоков, протекание которых по проводникам сопровождается их перегревом.
[ http://www.volt-m.ru/glossary/letter/%C4/view/11/]EN
current carrying capacity
maximum current a cable circuit (one or several conductors) can support resulting in a specified increase of the surface temperature of the conductor beyond the ambient temperature, not exceeding the maximum allowed operating temperature of the cable
[IEC 61156-1, ed. 3.0 (2007-06< size="2">)]FR
courant maximal admissible
courant maximal qu’un circuit de câble (un ou plusieurs conducteurs) peut supporter avec une augmentation spécifiée de la température de surface du conducteur au delà de la température ambiante, et ne dépassant pas la température maximale de fonctionnement autorisée du câble
[IEC 61156-1, ed. 3.0 (2007-06< size="2">)]Номинальный ток устройств защиты от короткого замыкания может превышать допустимый длительный ток кабеля.
[ ГОСТ Р 50571. 5-94 ( МЭК 364-4-43-77)]Допустимые длительные токи для проводов и кабелей, проложенных в коробах, а также в лотках пучками, должны приниматься...
[ПУЭ]Тематики
- кабели, провода...
- электроустановки
EN
- ampere capacity
- current carrying capacity
- current carrying capacity of the cable
- current carrying capacity of the conductors
- current-carrying capacity of the cable
FR
Франко-русский словарь нормативно-технической терминологии > courant maximal admissible
-
7 module d'élasticité de longue durée
длительный модуль упругости
Отношение напряжения к относительной деформации элемента после очень длительного выдерживания постоянной нагрузки.
[Сборник рекомендуемых терминов. Выпуск 82. Строительная механика. Академия наук СССР. Комитет научно-технической терминологии. 1970 г.]
модуль упругости длительный
Модуль упругости, определённый после длительного выдерживания материала под нагрузкой с целью исключения влияния процесса релаксации
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- строительная механика, сопротивление материалов
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > module d'élasticité de longue durée
-
8 long
1. прил.общ. длительный, продолжительный, долгий, длинный2. сущ.1) общ. длительный, продолжительный, протяжённость, медлительный, вьетнамка (обувь), долгий, разновидность игры в шары (на юге Франции), в длинной одежде, длина, длинный (о протяжении)2) тех. голень, паголенок, текст3) лингв. долгая гласная, долгий слог4) муз. долгая нота5) маш. longueur -
9 courant limite de service continu d'un circuit de sortie
предельный длительный ток выходной цепи электрического реле
Наибольшее значение тока, которое предварительно замкнутая или находящаяся в проводящем состоянии выходная цепь электрического реле способна выдерживать длительно в заданных условиях
[ ГОСТ 16022-83]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant limite de service continu d'un circuit de sortie
-
10 service ininterrompu (pour un dispositif de coupure)
непрерывный режим
длительный режим
-
[IEV number 442-05-43]EN
uninterrupted duty (for a switching device)
duty in which the main contacts of a switching device remain closed whilst carrying a steady current without interruption for long periods (which could be weeks, months, or even years)
[IEV number 442-05-43]FR
service ininterrompu (pour un dispositif de coupure)
service dans lequel les contacts principaux d'un dispositif de coupure restent fermés tout en transportant un courant permanent sans interruption pendant de longues périodes (qui peuvent être des semaines, des mois, et même des années)
[IEV number 442-05-43]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > service ininterrompu (pour un dispositif de coupure)
-
11 persistant traineé
устойчивый метеорный след
устойчивый след
ндп. длительный метеорный след
Светящийся след продолжительностью больше секунды.
[ ГОСТ 25645.112-84]Недопустимые, нерекомендуемые
Тематики
Обобщающие термины
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > persistant traineé
-
12 Courant limite de service continu d’un circuit de sortie
113. Предельный длительный ток выходной цепи электрического реле
D. Grenzdauerstrom eines Ausgangskreises
Е. Limiting continuous current of an output circuit
F. Courant limite de service continu d’un circuit de sortie
Наибольшее значение тока, которое предварительно замкнутая или находящаяся в проводящем состоянии выходная цепь электрического реле способна выдерживать длительно в заданных условиях
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Франко-русский словарь нормативно-технической терминологии > Courant limite de service continu d’un circuit de sortie
-
13 désert
1. adj ( fém - déserte)1) пустынный; необитаемый2) пустой; скучныйjournée déserte — день без работы2. m1) пустыня••parler [prêcher] dans le désert — попусту говоритьil prêche dans le désert — это глас вопиющего в пустынеtraversée de désert — 1) длительный период нахождения не у власти, в стороне от дел ( о политическом деятеле) 2) период трудностей, кризиса, ожиданияfaire le désert autour de qn — отвернуться от кого-либо (в знак неодобрения); создать пустоту вокруг кого-либо3) одиночество -
14 durable
adjдолговременный, длительный; прочный -
15 duratif
-
16 haleine
f1) дыханиеmauvaise haleine — дурной запах изо ртаprendre haleine — перевести дух; собраться с духом••à perdre haleine, à perte d'haleine — до изнеможенияen haleine — в рабочем состоянии, в форме; в напряженииtenir en haleine — держать в напряженииtenir son ennemi en haleine — преследовать врага, не давая ему передышкиpolitique de longue haleine — политика дальнего прицелаtout d'une haleine — единым, одним духом2) дуновение; дух, запах -
17 long
1. adj ( fém - longue)1) длинный ( о протяжении)long comme le bras разг. — очень длинный••sauce longue — жидкий соус2) долгий, длинный; длительный, продолжительныйde longs jours — долгие дни, долгоmoins long de trente minutes — короче на тридцать минутlong à + infin — медлительный ( в чём-либо)le brouhaha est long à se calmer — шум долго не смолкаетà la longue loc adv — с течением времени, в конце концов3) медлительный2. mдлина, протяжённостьdix mètres de long — десять метров в длинуtomber de tout son long — растянуться во весь рост••scieur de long — продольный пильщикavoir les côtes en long прост. — 1) быть ленивым 2) быть уставшимen long, de long loc adv — в длину, вдоль, в продольном направленииde long en large loc adv — взад и вперёд, вдоль и поперёкau long, tout au long, tout du long loc adv — 1) полностью, ничего не опуская 2) от начала до концаtout au [du] long de... loc prép — по всей длине, на всём протяжении чего-либоle long de... loc prép — вдоль, поle long de la rivière loc prép — вдоль рекиdescendre le long de la corde loc prép — спуститься по верёвке3. adv1)en dire long sur... — много наговорить о...; красноречиво свидетельствовать о...s'habiller trop long — носить слишком длинное, ходить в длинном -
18 perdurable
adjдлительный, вечный -
19 persistant
adj ( fém - persistante)1) упорный, твёрдый; настойчивый2) стойкий; продолжающийся, длящийся; длительный3) бот. неопадающий, постоянный -
20 долгосрочный
1) ( длительный) long2) (о контракте, ссуде и т.п.) à long terme; à long échéance
См. также в других словарях:
длительный — См … Словарь синонимов
ДЛИТЕЛЬНЫЙ — ДЛИТЕЛЬНЫЙ, длительная, длительное; длителен, длительна, длительно (книжн.). 1. Долго продолжающийся, продолжительный. Длительное отсутствие. Длительная болезнь. 2. только полн. То же, что фрикативный (линг.). Толковый словарь Ушакова. Д.Н.… … Толковый словарь Ушакова
ДЛИТЕЛЬНЫЙ — ДЛИТЕЛЬНЫЙ, ая, ое; лен, льна. Долго продолжающийся. Д. отпуск. | сущ. длительность, и, жен. Толковый словарь Ожегова. С.И. Ожегов, Н.Ю. Шведова. 1949 1992 … Толковый словарь Ожегова
длительный — долгосрочный продолжительный — [Англо русский глоссарий основных терминов по вакцинологии и иммунизации. Всемирная организация здравоохранения, 2009 г.] Тематики вакцинология, иммунизация Синонимы долгосрочныйпродолжительный EN long term … Справочник технического переводчика
длительный — прил., употр. сравн. часто Морфология: длителен, длительна, длительно, длительны; длительнее Событие, явление является длительным, если оно долго продолжается. Длительные переговоры. | Длительный курс лечения. | Длительное хранение продуктов. |… … Толковый словарь Дмитриева
длительный ток контактной машины — длительный ток Условное эквивалентное значение тока, при непрерывном прохождении которого токоведущие части контактной машины будут нагреты до той же температуры, что и при прохождении реального тока в повторно кратковременном режиме. [ГОСТ 22990 … Справочник технического переводчика
длительный рабочий режим рентгеновской трубки — Рабочий режим рентгеновской трубки без ограничения времени. Примечание Длительный рабочий режим предполагается при структурном и спектральном анализе, иногда в рентгенодефектоскопии. [ГОСТ 20337 74] Тематики рентгеновские приборы … Справочник технического переводчика
длительный аварийный режим — — [А.С.Гольдберг. Англо русский энергетический словарь. 2006 г.] Тематики энергетика в целом EN long term emergency … Справочник технического переводчика
длительный допустимый ток — (длительный) допустимый ток Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме … Справочник технического переводчика
длительный модуль упругости — Отношение напряжения к относительной деформации элемента после очень длительного выдерживания постоянной нагрузки. [http://www.isopromat.ru/sopromat/terms] Тематики строительная механика, сопротивление материалов EN relахеd modulus of… … Справочник технического переводчика
длительный номинальный ток — — [Я.Н.Лугинский, М.С.Фези Жилинская, Ю.С.Кабиров. Англо русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.] Тематики электротехника, основные понятия EN continuous current rating … Справочник технического переводчика