-
121 main distribution switchboard
главный распределительный щит (ГРЩ)
Распределительный щит, через который снабжается электроэнергией все здание или его обособленная часть. Роль ГРЩ может выполнять ВРУ или щит низкого напряжения подстанции.
[ПУЭ]
главный распределительный щит
Электрощит в здании, обеспечивающий распределение энергии между подключенными к нему нагрузками и включение аварийных систем при падении напряжения.
[ ГОСТ Р 51321. 3-99 ( МЭК 60439-3-90)]
[ ГОСТ Р 50571.28-2006]EN
main distribution board
board in the building which fulfils all the functions of a main electrical distribution for the supply building area assigned to it and where the voltage drop is measured for operating the safety services
[IEC 60364-7-710, ed. 1.0 (2002-11)]FR
tableau général de distribution
tableau de distribution dans le bâtiment remplissant toutes les fonctions d’un tableau général de distribution pour l’alimentation de la zone qui lui est dédiée et où la chute de tension est mesurée pour le fonctionnement des services de sécurité
[IEC 60364-7-710, ed. 1.0 (2002-11)]
Главный распределительный щит (ГРЩ) на ток 6300 А
[http://www.uzoelectro.ru/catalogue/group-383/product-36465/ ]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
- электроустановки
Синонимы
EN
- feeder switchboard
- m.s.b.
- main distributing frame
- main distribution board
- main distribution switchboard
- Main Low Voltage Switchboard
- main low-voltage distribution switchboard
- main switchboard
- MLVS
- MSB
- power center
FR
Англо-русский словарь нормативно-технической терминологии > main distribution switchboard
-
122 Main Low Voltage Switchboard
главный распределительный щит (ГРЩ)
Распределительный щит, через который снабжается электроэнергией все здание или его обособленная часть. Роль ГРЩ может выполнять ВРУ или щит низкого напряжения подстанции.
[ПУЭ]
главный распределительный щит
Электрощит в здании, обеспечивающий распределение энергии между подключенными к нему нагрузками и включение аварийных систем при падении напряжения.
[ ГОСТ Р 51321. 3-99 ( МЭК 60439-3-90)]
[ ГОСТ Р 50571.28-2006]EN
main distribution board
board in the building which fulfils all the functions of a main electrical distribution for the supply building area assigned to it and where the voltage drop is measured for operating the safety services
[IEC 60364-7-710, ed. 1.0 (2002-11)]FR
tableau général de distribution
tableau de distribution dans le bâtiment remplissant toutes les fonctions d’un tableau général de distribution pour l’alimentation de la zone qui lui est dédiée et où la chute de tension est mesurée pour le fonctionnement des services de sécurité
[IEC 60364-7-710, ed. 1.0 (2002-11)]
Главный распределительный щит (ГРЩ) на ток 6300 А
[http://www.uzoelectro.ru/catalogue/group-383/product-36465/ ]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
- электроустановки
Синонимы
EN
- feeder switchboard
- m.s.b.
- main distributing frame
- main distribution board
- main distribution switchboard
- Main Low Voltage Switchboard
- main low-voltage distribution switchboard
- main switchboard
- MLVS
- MSB
- power center
FR
Англо-русский словарь нормативно-технической терминологии > Main Low Voltage Switchboard
-
123 main low-voltage distribution switchboard
главный распределительный щит (ГРЩ)
Распределительный щит, через который снабжается электроэнергией все здание или его обособленная часть. Роль ГРЩ может выполнять ВРУ или щит низкого напряжения подстанции.
[ПУЭ]
главный распределительный щит
Электрощит в здании, обеспечивающий распределение энергии между подключенными к нему нагрузками и включение аварийных систем при падении напряжения.
[ ГОСТ Р 51321. 3-99 ( МЭК 60439-3-90)]
[ ГОСТ Р 50571.28-2006]EN
main distribution board
board in the building which fulfils all the functions of a main electrical distribution for the supply building area assigned to it and where the voltage drop is measured for operating the safety services
[IEC 60364-7-710, ed. 1.0 (2002-11)]FR
tableau général de distribution
tableau de distribution dans le bâtiment remplissant toutes les fonctions d’un tableau général de distribution pour l’alimentation de la zone qui lui est dédiée et où la chute de tension est mesurée pour le fonctionnement des services de sécurité
[IEC 60364-7-710, ed. 1.0 (2002-11)]
Главный распределительный щит (ГРЩ) на ток 6300 А
[http://www.uzoelectro.ru/catalogue/group-383/product-36465/ ]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
- электроустановки
Синонимы
EN
- feeder switchboard
- m.s.b.
- main distributing frame
- main distribution board
- main distribution switchboard
- Main Low Voltage Switchboard
- main low-voltage distribution switchboard
- main switchboard
- MLVS
- MSB
- power center
FR
Англо-русский словарь нормативно-технической терминологии > main low-voltage distribution switchboard
-
124 main switchboard
главный распределительный щит (ГРЩ)
Распределительный щит, через который снабжается электроэнергией все здание или его обособленная часть. Роль ГРЩ может выполнять ВРУ или щит низкого напряжения подстанции.
[ПУЭ]
главный распределительный щит
Электрощит в здании, обеспечивающий распределение энергии между подключенными к нему нагрузками и включение аварийных систем при падении напряжения.
[ ГОСТ Р 51321. 3-99 ( МЭК 60439-3-90)]
[ ГОСТ Р 50571.28-2006]EN
main distribution board
board in the building which fulfils all the functions of a main electrical distribution for the supply building area assigned to it and where the voltage drop is measured for operating the safety services
[IEC 60364-7-710, ed. 1.0 (2002-11)]FR
tableau général de distribution
tableau de distribution dans le bâtiment remplissant toutes les fonctions d’un tableau général de distribution pour l’alimentation de la zone qui lui est dédiée et où la chute de tension est mesurée pour le fonctionnement des services de sécurité
[IEC 60364-7-710, ed. 1.0 (2002-11)]
Главный распределительный щит (ГРЩ) на ток 6300 А
[http://www.uzoelectro.ru/catalogue/group-383/product-36465/ ]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
- электроустановки
Синонимы
EN
- feeder switchboard
- m.s.b.
- main distributing frame
- main distribution board
- main distribution switchboard
- Main Low Voltage Switchboard
- main low-voltage distribution switchboard
- main switchboard
- MLVS
- MSB
- power center
FR
Англо-русский словарь нормативно-технической терминологии > main switchboard
-
125 MLVS
главный распределительный щит (ГРЩ)
Распределительный щит, через который снабжается электроэнергией все здание или его обособленная часть. Роль ГРЩ может выполнять ВРУ или щит низкого напряжения подстанции.
[ПУЭ]
главный распределительный щит
Электрощит в здании, обеспечивающий распределение энергии между подключенными к нему нагрузками и включение аварийных систем при падении напряжения.
[ ГОСТ Р 51321. 3-99 ( МЭК 60439-3-90)]
[ ГОСТ Р 50571.28-2006]EN
main distribution board
board in the building which fulfils all the functions of a main electrical distribution for the supply building area assigned to it and where the voltage drop is measured for operating the safety services
[IEC 60364-7-710, ed. 1.0 (2002-11)]FR
tableau général de distribution
tableau de distribution dans le bâtiment remplissant toutes les fonctions d’un tableau général de distribution pour l’alimentation de la zone qui lui est dédiée et où la chute de tension est mesurée pour le fonctionnement des services de sécurité
[IEC 60364-7-710, ed. 1.0 (2002-11)]
Главный распределительный щит (ГРЩ) на ток 6300 А
[http://www.uzoelectro.ru/catalogue/group-383/product-36465/ ]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
- электроустановки
Синонимы
EN
- feeder switchboard
- m.s.b.
- main distributing frame
- main distribution board
- main distribution switchboard
- Main Low Voltage Switchboard
- main low-voltage distribution switchboard
- main switchboard
- MLVS
- MSB
- power center
FR
Англо-русский словарь нормативно-технической терминологии > MLVS
-
126 power center
главный распределительный щит (ГРЩ)
Распределительный щит, через который снабжается электроэнергией все здание или его обособленная часть. Роль ГРЩ может выполнять ВРУ или щит низкого напряжения подстанции.
[ПУЭ]
главный распределительный щит
Электрощит в здании, обеспечивающий распределение энергии между подключенными к нему нагрузками и включение аварийных систем при падении напряжения.
[ ГОСТ Р 51321. 3-99 ( МЭК 60439-3-90)]
[ ГОСТ Р 50571.28-2006]EN
main distribution board
board in the building which fulfils all the functions of a main electrical distribution for the supply building area assigned to it and where the voltage drop is measured for operating the safety services
[IEC 60364-7-710, ed. 1.0 (2002-11)]FR
tableau général de distribution
tableau de distribution dans le bâtiment remplissant toutes les fonctions d’un tableau général de distribution pour l’alimentation de la zone qui lui est dédiée et où la chute de tension est mesurée pour le fonctionnement des services de sécurité
[IEC 60364-7-710, ed. 1.0 (2002-11)]
Главный распределительный щит (ГРЩ) на ток 6300 А
[http://www.uzoelectro.ru/catalogue/group-383/product-36465/ ]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
- электроустановки
Синонимы
EN
- feeder switchboard
- m.s.b.
- main distributing frame
- main distribution board
- main distribution switchboard
- Main Low Voltage Switchboard
- main low-voltage distribution switchboard
- main switchboard
- MLVS
- MSB
- power center
FR
комплектное устройство первичного распределения электроэнергии
-
[Интент]
Рис. ABBПараллельные тексты EN-RU
They are usually installed on the load side of MV/LV transformers or generators.
These assemblies include one or more incoming units, bus ties and a relatively reduced number of outgoing units.
There are also present measuring instruments and other switching and control equipment.
These assemblies have a sturdy structure to withstand the electrodynamic stresses and the weight of big sized apparatus.
As a matter of fact peculiar characteristics of the power center are high rated currents and shortcircuit currents.
The constructional type is a cubicle structure, with metal enclosure and sections divided into compartments with selective access.
[ABB]Такие устройства обычно подключают на стороне нагрузки СВ/НВ трансформаторов или генераторов.
В их состав входят один или несколько блоков ввода, шины и относительно небольшое число блоков вывода.
В состав комплектного устройства первичного распределения электроэнергии входят также измерительные приборы, коммутационные устройства и средства контроля состояния.
Данные комплектные устройства имеют прочную конструкцию, способную выдерживать электродинамическое действие токов и вес крупногабаритной аппаратуры.
Центры распределения электроэнергии характеризуются высокими номинальным током и током короткого замыкания.
С точки зрения конструктивного исполнения они представляют собой многошкафное комплектное устройство в металлической оболочке, состоящее из секций, каждая из которых разделена на отсеки с независимым доступом.
[Перевод Интент]Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
- комплектное распред. устройство (КРУ)
EN
Англо-русский словарь нормативно-технической терминологии > power center
-
127 continuous current-carrying capacity
длительная пропускная способность по току
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Англо-русский словарь нормативно-технической терминологии > continuous current-carrying capacity
-
128 ampacity (US)
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Англо-русский словарь нормативно-технической терминологии > ampacity (US)
См. также в других словарях:
ГОСТ Р 50571.1-93 — ГОСТ 30331.1 95 (МЭК 364 1 72, МЭК 364 2 70)/ГОСТ Р 50571.1 93 (МЭК 364 1 72, МЭК 364 2 70) Утратил силу в РФ Пользоваться: ГОСТ Р 50571.1 2009 (МЭК 60364 1:2005) … Указатель национальных стандартов 2013
ГОСТ Р 50571.3-94 — ГОСТ 30331.3 95 (МЭК 364 4 41 92)/ГОСТ Р 50571.3 94 (МЭК 364 4 41 92) Утратил силу в РФ Пользоваться: ГОСТ Р 50571.3 2009 (МЭК 60364 4 41:2005) … Указатель национальных стандартов 2013
ГОСТ Р 50571.8-94 — ГОСТ 30331.8 95 (МЭК 364 4 47 81)/ГОСТ Р 50571.8 94 (МЭК 364 4 47 81) Утратил силу в РФ Пользоваться: ГОСТ Р 50571.3 2009 (МЭК 60364 4 41:2005) … Указатель национальных стандартов 2013
ГОСТ Р 50571.2-94 — (МЭК 364 3 93) 46 с. (7) Электроустановки зданий. Часть 3. Основные характеристики Заменен: ГОСТ Р 50571.1 2009 в части пунктов 31, 33, 34, 35 Принят в качестве межгосударственного стандарта раздел 91.140.50 … Указатель национальных стандартов 2013
ГОСТ Р 50571.11-96 — (МЭК 364 7 701 84) 8 с. (2) Электроустановки зданий. Часть 7. Требования к специальным электроустановкам. Раздел 701. Ванные и душевые помещения раздел 91.140.50 … Указатель национальных стандартов 2013
ГОСТ Р 50571.12-96 — (МЭК 364 7 703 84) 6 с. (2) Электроустановки зданий. Часть 7. Требования к специальным электроустановкам. Раздел 703. Помещения, содержащие нагреватели для саун раздел 91.140.50 … Указатель национальных стандартов 2013
ГОСТ Р 50571.13-96 — (МЭК 364 7 706 83) 6 с. (2) Электроустановки зданий. Часть 7. Требования к специальным электроустановкам. Раздел 706. Стесненные помещения с проводящим полом, стенами и потолком раздел 91.140.50 … Указатель национальных стандартов 2013
ГОСТ Р 50571.14-96 — (МЭК 364 7 705 84) 8 с. (2) Электроустановки зданий. Часть 7. Требования к специальным электроустановкам. Раздел 705. Электроустановки сельскохозяйственных и животноводческих помещений раздел 91.140.50 … Указатель национальных стандартов 2013
ГОСТ Р 50571.4-94 — (МЭК 364 4 42 80) 6 с. (2) Электроустановки зданий. Часть 4. Требования по обеспечению безопасности. Защита от тепловых воздействий Принят в качестве межгосударственного стандарта разделы 29.120.50, 91.140.50 … Указатель национальных стандартов 2013
ГОСТ Р 50571.5-94 — (МЭК 364 4 43 77) 8 с. (2) Электроустановки зданий. Часть 4. Требования по обеспечению безопасности. Защита от сверхтока Принят в качестве межгосударственного стандарта разделы 29.120.50, 91.140.50 … Указатель национальных стандартов 2013
ГОСТ Р 50571.6-94 — (МЭК 364 4 45 84) 6 с. (2) Электроустановки зданий. Часть 4. Требования по обеспечению безопасности. Защита от понижения напряжения Принят в качестве межгосударственного стандарта разделы 29.120.50, 29.120.70, 91.140.50 … Указатель национальных стандартов 2013