-
21 incomplete penetration
неполное проплавление
Проплавление, глубина которого менее установленной.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]EN
incomplete penetration
Penetration that is less than that required or specified.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]FR
manque de pénétration
Pénétration moindre que celle exigée ou spécifiée.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]Тематики
- сварка, резка, пайка
EN
FR
Англо-русский словарь нормативно-технической терминологии > incomplete penetration
-
22 partial penetration
неполный провар
(шва при сварке)
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
частичное проплавление
Проплавление, которое преднамеренно не является полным.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]EN
partial penetration
Penetration that is intentionally not full penetration.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]FR
pénétration partielle
Pénétration volontairement moindre qu'une pleine pénétration.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]Тематики
- сварка, резка, пайка
EN
FR
Англо-русский словарь нормативно-технической терминологии > partial penetration
-
23 cross joint
перекрестное соединение
Тип соединения, при котором две детали (например, проволоки) лежат друг на друге пересекаясь.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]EN
cross joint
Type of joint where two parts (e.g. wires) lie crossing over each other.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]FR
assemblage de fils en croix
assemblage de ronds en croix
Type d'assemblage dans lequel deux pièces, par exemple des fils ou des ronds, forment une croix.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]Тематики
- сварка, резка, пайка
EN
FR
Англо-русский словарь нормативно-технической терминологии > cross joint
-
24 design throat thickness
проектная толщина шва
Толщина шва, установленная проектировщиком.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]EN
design throat thickness
Throat thickness specified by the designer.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]FR
gorge théorique(soudures d'angle)
épaisseur théorique (soudures bout а bout)
Gorge spécifiée par le concepteur.
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]Тематики
- сварка, резка, пайка
EN
FR
Англо-русский словарь нормативно-технической терминологии > design throat thickness
-
25 throat thickness specified by the designer
totale (soudures d'angle) épaisseur totale (soudures bout а bout)
soudures d'angle distance mesurée entre le point le plus bas de la pénétration et le point le plus haut de la surépaisseur soudures bout а bout distance mesurée entre le point le plus bas de la passe de fond et le point le plus haut de la surépaisseur
throat thickness specified by the designer
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
throat thickness specified by the designer
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > throat thickness specified by the designer
-
26 side of the largest isosceles triangle that can be inscribed in the section
катет углового шва: Сторона наибольшего равнобедренного треугольника, который можно вписать в сечение шва.
side of the largest isosceles triangle that can be inscribed in the section
soudures d'angle côté du plus grand triangle isocèle inscrit dans la section
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
side of the largest isosceles triangle that can be inscribed in the section
soudures d'angle côté du plus grand triangle isocèle inscrit dans la section
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > side of the largest isosceles triangle that can be inscribed in the section
-
27 the junction of workpieces or the edges of workpieces that are to be joined or have been joined
the junction of workpieces or the edges of workpieces that are to be joined or have been joined
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > the junction of workpieces or the edges of workpieces that are to be joined or have been joined
-
28 welding involving localized melting without the application of external force in which the fusion surface(s) has (have) to be melted
welding involving localized melting without the application of external force in which the fusion surface(s) has (have) to be melted
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > welding involving localized melting without the application of external force in which the fusion surface(s) has (have) to be melted
-
29 welding in which sufficient external force is applied to cause more or less plastic deformation of both the contact surfaces, generally without the addition of filler metal
welding in which sufficient external force is applied to cause more or less plastic deformation of both the contact surfaces, generally without the addition of filler metal
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > welding in which sufficient external force is applied to cause more or less plastic deformation of both the contact surfaces, generally without the addition of filler metal
-
30 surface of one component that is intended to be in contact with a surface of another component to form a joint
surface of one component that is intended to be in contact with a surface of another component to form a joint
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > surface of one component that is intended to be in contact with a surface of another component to form a joint
-
31 penetration that is intentionally not full penetration
penetration that is intentionally not full penetration
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > penetration that is intentionally not full penetration
-
32 penetration that is less than that required or specified
penetration that is less than that required or specified
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > penetration that is less than that required or specified
-
33 type of joint where the parts lie approximately in the same plane and abut against one another
type of joint where the parts lie approximately in the same plane and abut against one another
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > type of joint where the parts lie approximately in the same plane and abut against one another
-
34 type of joint where the parts lie parallel to each other and overlap each other
type of joint where the parts lie parallel to each other and overlap each other
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > type of joint where the parts lie parallel to each other and overlap each other
-
35 type of joint where the parts meet each other at approximately right angles (forming a T-shape)
type of joint where the parts meet each other at approximately right angles (forming a T-shape)
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > type of joint where the parts meet each other at approximately right angles (forming a T-shape)
-
36 type of joint where two parts lying in the same plane each meet, at right angles, a third part lying between them (forming a double T-shape)
type of joint where two parts lying in the same plane each meet, at right angles, a third part lying between them (forming a double T-shape)
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > type of joint where two parts lying in the same plane each meet, at right angles, a third part lying between them (forming a double T-shape)
-
37 type of joint where one part meets the other at an acute angle
type of joint where one part meets the other at an acute angle
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > type of joint where one part meets the other at an acute angle
-
38 type of joint where three or more parts meet at any required angle to each other
type of joint where three or more parts meet at any required angle to each other
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > type of joint where three or more parts meet at any required angle to each other
-
39 dimension measured from the deepest point of the penetration in fillet welds or the extremity of the root run in butt welds to the highest point of the excess weld metal
dimension measured from the deepest point of the penetration in fillet welds or the extremity of the root run in butt welds to the highest point of the excess weld metal
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > dimension measured from the deepest point of the penetration in fillet welds or the extremity of the root run in butt welds to the highest point of the excess weld metal
-
40 dimension that is responsible for carrying the load, dependent on the shape and penetration of the weld
dimension that is responsible for carrying the load, dependent on the shape and penetration of the weld
Источник: ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений оригинал документа
Англо-русский словарь нормативно-технической терминологии > dimension that is responsible for carrying the load, dependent on the shape and penetration of the weld
- 1
- 2
См. также в других словарях:
ГОСТ Р ИСО 17659-2009 — 40 с. (6) Сварка. Термины многоязычные для сварных соединений раздел 25.160.40 … Указатель национальных стандартов 2013
ГОСТ Р ИСО 17659-2009: Сварка. Термины многоязычные для сварных соединений — Терминология ГОСТ Р ИСО 17659 2009: Сварка. Термины многоязычные для сварных соединений оригинал документа: actual throat thickness (fillet welds), the value of the height of the largest isosceles triangle that can be inscribed in the section of… … Словарь-справочник терминов нормативно-технической документации
ГОСТ 2601-84 — 57 с. (9) Сварка металлов. Термины и определения основных понятий Взамен: ГОСТ 2601 74; ГОСТ 19232 73 Прекращено применение на территории Российской Федерации в части пп. 1 12, 16 22, 27 33, 36 45, 47, 48, 50 55, 77, 79, 94, 95, 139, 169, с 01.07 … Указатель национальных стандартов 2013
assemblage — disposition relative des pièces ou des bords des pièces à souder ou qui ont été soudé(e)s Источник: ГОСТ Р ИСО 17659 2009: Сварка. Термины многоязычные для сварных соединений оригинал документа … Словарь-справочник терминов нормативно-технической документации
соединение — 01.03.16 соединение [ concatenation]: Средство для связывания воедино отдельных элементов данных, хранящихся на носителях данных, для формирования отдельного файла или поля данных. Источник … Словарь-справочник терминов нормативно-технической документации
сварка давлением — Сварка, осуществляемая приложением внешней силы и сопровождаемая пластическим деформированием сопрягаемых поверхностей, обычно без присадочного металла. Примечание Сопрягаемые поверхности можно нагревать, чтобы облегчить получение соединения.… … Справочник технического переводчика
сварка плавлением — Сварка, осуществляемая оплавлением сопрягаемых поверхностей без приложения внешней силы; обычно, но необязательно, добавляется расплавленный присадочный металл. [ГОСТ Р ИСО 857 1 2009] [ГОСТ Р ИСО 17659 2009] [ISO 17659:2002] сварка плавлением… … Справочник технического переводчика
теоретическая толщина углового шва — Высота наибольшего равнобедренного треугольника, который можно вписать в сечение выполненного шва; теоретическая толщина стыкового шва: Минимальное расстояние от поверхности детали до корня шва [ИСО 2553] [ГОСТ Р ИСО 17659 2009] [ISO 17659:2002]… … Справочник технического переводчика
катет углового шва — Сторона наибольшего равнобедренного треугольника, который можно вписать в сечение шва [ГОСТ Р ИСО 17659 2009] [ISO 17659:2002] катет углового шва катет шва Кратчайшее расстояние от поверхности одной из свариваемых частей до границы углового шва… … Справочник технического переводчика
нахлесточное соединение — Сварное соединение, в котором сваренные элементы расположены параллельно и частично перекрывают друг друга [ГОСТ 2601 84] [Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)] нахлесточное соединение Тип соединения, при … Справочник технического переводчика
торцовое соединение — Ндп. боковое соединение Сварное соединение, в котором боковые поверхности сваренных элементов примыкают друг к другу [ГОСТ 2601 84] торцовое соединение Тип соединения, при котором угол между поверхностями двух деталей в месте примыкания кромок… … Справочник технического переводчика