-
101 interrupteur à bouton-poussoir
кнопочный выключатель
Выключатель, управляемый с помощью кнопки, имеющей привод, для оперирования силой, создаваемой частью человеческого тела, обычно ладонью или пальцем руки, и имеющий устройство возврата накопленной энергии, например пружину.
[ ГОСТ Р 51324. 1-2005 ( МЭК 60669-1: 2000)]
кнопочный выключатель
Выключатель, приводимый в действие нажатием или вытягиванием детали, передающей усилие оператора.
[ ГОСТ 17703-72]
[IEV number 442-04-07]
(нажимная) кнопка
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва]EN
push-button switch
switch, the actuating member of which is a button which has to be pushed in order to achieve a change in contact state
NOTE - The switch may be provided with one or more actuating members.
[IEC 61058-1, ed. 3.0 (2000-07)]
[IEV number 442-04-07]FR
interrupteur à bouton-poussoir
interrupteur dont l'organe de manoeuvre est un bouton qui doit être poussé afin d'obtenir un changement de l'état des contacts
NOTE - L'interrupteur peut être équipé d'un ou de plusieurs organes de manoeuvre
[IEC 61058-1, ed. 3.0 (2000-07)]
[IEV number 442-04-07]
КЛАССИФИКАЦИЯ
Раньше кнопочные выключатели классифицировали по виду толкателя:-
с цилиндрическим толкателем
-
с грибовидным толкателем
-
с поворотной ручкой
- с ручкой, расположенной в исходном положении на вертикальной оси, воздействующей на контакты при повороте на 90о
- с ручкой, расположенной в исходном положении под углом 45о от вертикальной оси, воздействующей на контакты при повороте на 90о
- с ручкой, расположенной в исходном положении на вертикальной оси, воздействующей на контакты при повороте в одну и другую сторону на 90о
-
с замком
- ключ во включенном положении вынимается
- ключ замка в исходном положении расположен по вертикальной оси, воздействие на контакты при повороте на 90о
- ключ замка в исходном положении расположен по вертикальной оси, воздействие на контакты при повороте в одну и другую строну на 90о
-
ключ во включенном положении не вынимается
- ключ замка в исходном положении расположен по вертикальной оси, воздействие на контакты при повороте на 90о
- ключ замка в исходном положении расположен по вертикальной оси, воздействие на контакты при повороте в одну и другую строну на 90о
1 - Фронтальная гайка
2 - Установочное отверстие
3 - Панель
4 - Ориентирующее кольцо
5 - Контактный зажим
6 - Контактный узел
7 - Прижимная гайка
8 - Цилиндрический толкатель
Кнопочный выключатель устанавливается на панели 3 толщиной не более 6 мм в установочном отверстии 2 диаметром 22,5 мм и фиксируется фронтальной 1 и прижимной 7 гайками. Для предотвращения поворота выключателя имеется ориентирующее кольцо 4. Провода присоединяются к винтовым зажимам 5.
Тематики
- выключатель кнопочный, кнопка
Обобщающие термины
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > interrupteur à bouton-poussoir
-
с цилиндрическим толкателем
-
102 mécanisme à déclenchement libre
механизм свободного расцепления
-
[IEV number 442-01-45]
механизм свободного расцепления
Обеспечивает мгновенное замыкание и размыкание контактов, не зависящее от скорости движения рукоятки управления, а также автоматическое отключение автоматического выключателя под действием расцепителей независимо от положения в данный момент органов ручного управленияEN
trip-free mechanism
a mechanism designed so that disconnection can neither be prevented nor inhibited by a reset mechanism, and so that the contacts can neither be prevented from opening nor be maintained closed against a continuation of the excess temperature or current
[IEV number 442-01-45]FR
mécanisme à déclenchement libre
mécanisme conçu de façon telle que la déconnexion ne puisse être ni empêchée ni interdite par un organe de réenclenchement et que les contacts ne doivent pas avoir leur ouverture empêchée ou être maintenus collés lors du maintien d'une température ou d'un courant excessif
[IEV number 442-01-45].
Тематики
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > mécanisme à déclenchement libre
-
103 appareillage pour l'intérieur
НКУ внутренней установки
НКУ, предназначенное для эксплуатации внутри помещений
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
НКУ для внутренней установки
НКУ, предназначенное для применения в местах, где выполняются условия нормальной эксплуатации внутри помещений согласно 7.1.
[ ГОСТ Р МЭК 61439.1-2013]EN
indoor switchgear and controlgear
switchgear and controlgear designed solely for installation within a building or other housing, where the switchgear and controlgear is protected against wind, rain, snow, abnormal dirt deposits, abnormal condensation, ice and hoar frost
[IEV number 441-11-04]
assembly for indoor installation
assembly which is designed for use in locations where the normal service conditions for indoor use as specified in 7.1 are fulfilled
[IEC 61439-1, ed. 2.0 (2011-08)]FR
appareillage pour l'intérieur
appareillage qui n'est conçu que pour être installé à l'intérieur d'un bâtiment ou d'un autre abri, dans lequel l'appareillage est protégé contre le vent, la pluie, la neige, les pollutions anormales, la condensation anormale, la glace et le givre
[IEV number 441-11-04]
ensemble pour installation à l'intérieur
ensemble destiné à être utilisé dans des locaux où les conditions normales d'emploi pour l'intérieur, spécifiées en 7.1, sont satisfaites
[IEC 61439-1, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>EN
DE
- Innen(raum)-Schaltanlagen und/oder -Schaltgeräte
FR
Франко-русский словарь нормативно-технической терминологии > appareillage pour l'intérieur
-
104 ensemble pour installation à l'intérieur
НКУ внутренней установки
НКУ, предназначенное для эксплуатации внутри помещений
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
НКУ для внутренней установки
НКУ, предназначенное для применения в местах, где выполняются условия нормальной эксплуатации внутри помещений согласно 7.1.
[ ГОСТ Р МЭК 61439.1-2013]EN
indoor switchgear and controlgear
switchgear and controlgear designed solely for installation within a building or other housing, where the switchgear and controlgear is protected against wind, rain, snow, abnormal dirt deposits, abnormal condensation, ice and hoar frost
[IEV number 441-11-04]
assembly for indoor installation
assembly which is designed for use in locations where the normal service conditions for indoor use as specified in 7.1 are fulfilled
[IEC 61439-1, ed. 2.0 (2011-08)]FR
appareillage pour l'intérieur
appareillage qui n'est conçu que pour être installé à l'intérieur d'un bâtiment ou d'un autre abri, dans lequel l'appareillage est protégé contre le vent, la pluie, la neige, les pollutions anormales, la condensation anormale, la glace et le givre
[IEV number 441-11-04]
ensemble pour installation à l'intérieur
ensemble destiné à être utilisé dans des locaux où les conditions normales d'emploi pour l'intérieur, spécifiées en 7.1, sont satisfaites
[IEC 61439-1, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>EN
DE
- Innen(raum)-Schaltanlagen und/oder -Schaltgeräte
FR
Франко-русский словарь нормативно-технической терминологии > ensemble pour installation à l'intérieur
-
105 bouton-poussoir à verrouillage
нажимная кнопка с блокировкой
Аппарат, который может находиться в одном или нескольких положениях за счет отдельного воздействия (нажатием).
Примечание
Блокировка может быть достигнута вращением кнопки, поворотом ключа, воздействием на рычаг и т. д.
[ ГОСТ 50030.5.1-2005]EN
locked push-button
a push-button which may be secured in one or more of its positions by a separate action
NOTE - The locking may be obtained by turning the button, by turning a key, by operating a lever, etc.
[IEC 60947-5-1, ed. 3.0 (2003-11)]FR
bouton-poussoir à verrouillage
bouton-poussoir qui peut être maintenu dans une ou plusieurs de ses positions par une action séparée
NOTE - Le verrouillage peut être obtenu par rotation du bouton, par rotation d'une clef, par action sur un levier, etc.
[IEC 60947-5-1, ed. 3.0 (2003-11)]…должны быть применены кнопки с фиксацией, которые после их нажатия не возвращаются в первоначальное состояние до тех пор, пока не будут принудительно приведены в это состояние.
[ ГОСТ 12.2.007.0-75]Тематики
- аппарат, изделие, устройство...
- выключатель кнопочный, кнопка
EN
FR
Франко-русский словарь нормативно-технической терминологии > bouton-poussoir à verrouillage
-
106 baie
шкаф
Оболочка, как правило, имеющая большие размеры, предназначенная для установки на полу, которая может состоять из нескольких секций, подсекций или отсеков.
Примечание - Оболочки нестандартной формы, например пульты для испытаний, считают шкафами.
[ ГОСТ Р 52796- 2007( МЭК 62208: 2002)]
EN
cabinet
free-standing and self-supporting enclosure for housing electrical and/or electronic equipment
It is usually fitted with doors and/or side panels which may or may not be removable.[IEC 60917-1, ed. 1.0 (1998-09)]
[IEV number 581-25-02]
cabinet
container that may enclose connection devices, terminations, apparatus, cabling, and equipment. It may be either wall-mounted or self-supporting
[IEC 62134-1, ed. 2.0 (2009-06)]
cubicle
empty enclosure, generally of large dimensions, and in principle of the floor standing type, which may comprise several sections, sub-sections or compartments
NOTE Enclosures with an irregular shape, such as a desk, are considered cubicles for testing purposes.
[IEC 62208, ed. 1.0 (2002-11)]R
baie
structure fermée indépendante et auto-porteuse destinée à loger du matériel électrique et/ou électronique
Elle est habituellement munie de portes et/ou de panneaux latéraux qui peuvent être amovibles ou non.[IEC 60917-1, ed. 1.0 (1998-09)]
[IEV number 581-25-02]
armoire
conteneur qui peut abriter des dispositifs de connexion, des terminaisons, des appareillages, des câblages et des équipements. Elle peut être fixée au mur ou être auto-porteuse
[IEC 62134-1, ed. 2.0 (2009-06)]
armoire
enveloppe vide, généralement de grandes dimensions et, en principe fixée au sol, qui peut comprendre plusieurs colonnes, éléments de colonne ou compartiments
NOTE Les enveloppes ayant une forme irrégulière telle qu'un pupitre sont considérées comme des armoires pour les essais.
[IEC 62208, ed. 1.0 (2002-11)]Тематики
- НКУ (шкафы, пульты,...)
EN
DE
- Schrank, m
FR
проём
Большое отверстие в ограждающих конструкциях зданий и сооружений, устраиваемое в эксплуатационных или монтажных целях
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > baie
-
107 dispositif de connexion par épissure non réutilisable
одноразовое устройство соединения проводников скручиванием
-
[IEV number 442-06-38]EN
non-reusable twist-on connecting device
Twist-on connecting device that can only be used once and which is constructed in such a way that it cannot be separated from the conductor without being completely destroyed
[IEV number 442-06-38]FR
dispositif de connexion par épissure non réutilisable
Dispositif de connexion par épissure qui ne peut être utilisé qu'une seule fois et qui est construit de telle façon qu'il ne puisse être séparé des âmes des conducteurs sans être définitivement détruit
[IEV number 442-06-38]EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > dispositif de connexion par épissure non réutilisable
-
108 élément de dérivation
ответвительное устройство (на шинопроводе)
ответвительная коробка (на шинопроводе)
-
ответвительное устройство
узел ответвления
Устройство отвода электроэнергии от секции шинопровода с местами для присоединения ответвительных устройств (см. 2.3.6), например с помощью роликов, щеток или втычных устройств.
Узел ответвления может быть включен постоянно и предназначаться для работы с одной или несколькими комбинациями цепей питания, связи или управления.
Узел ответвления может включать в себя дополнительные устройства, такие как устройства защиты (например, предохранители, разъединители с плавкими предохранителями, автоматические выключатели, автоматические выключатели дифференциального тока), электронное оборудование для связи или дистанционного управления, контакторы, розетки, соединительную арматуру, такую как предварительно смонтированные клеммы с винтовым или безвинтовым креплением, и т.д.
Узлы ответвления могут представлять собой устройства, прошедшие частичные типовые испытания (ЧИ НКУ).
[ ГОСТ Р 51321.2-2009]EN
tap-off unit
outgoing unit for tapping-off power from the busbar trunking unit with tap-off facilities (see 2.3.6), such as rollers, brushes or plug-in devices
A tap-off unit may also be permanently connected and can be intended for one or any combinations of power, communication or control circuits.
A tap-off unit may contain accessories, such as protective devices (for example fuse, fuse-switch, switch-fuse, circuit-breaker, residual current circuit-breaker), electronic apparatus for communication or remote control, contactors, socket-outlets, connecting facilities such as prewired, screw-type or screw-less type terminals, etc.
Tap-off units may be partially type-tested assemblies (PTTA).
[IEC 60439-2, ed. 3.0 (2000-03)]FR
élément de dérivation
unité de départ d'une canalisation préfabriquée avec possibilité de dérivations (voir 2.3.6), telles que matériel à contact roulant ou glissant ou connecteurs débrochables
Un élément de dérivation peut être connecté d’une façon permanente et peut être destiné à recevoir une ou plusieurs combinaisons de circuits de puissance, de communication ou de contrôle.
Un élément de dérivation peut aussi contenir des accessoires, tels que des dispositifs de protection (par exemple fusibles, fusibles-interrupteur, interrupteur-fusibles, disjoncteurs, disjoncteurs à courant résiduel), de l’appareillage électronique à usage de communication ou de contrôle à distance, des contacteurs pour des fonctions d’automatisation, des prises de courant, des facilités de raccordement telles que du précâblage ou des bornes de raccordement du type à vis ou du type sans vis, etc.
Les éléments de dérivation peuvent être des ensembles dérivés de série (EDS).
[IEC 60439-2, ed. 3.0 (2000-03)]2.3. Номинальные токи шинопроводов и их ответвительных устройств (коробок, штепселей, ответвительных секций) должны соответствовать...
4.4. Конструкция шинопровода с ответвительными устройствами, предназначенными для разъемного присоединения приемников электрической энергии, должна исключать возможность подключения нулевых контактов ответвительных устройств к фазным проводникам шинопровода.
4.4а. Конструкция ответвительных устройств, предназначенных для разъемного присоединения приемников электрической энергии, должна обеспечивать опережающее подключение заземляющих контактов ответвительных устройств к заземленной оболочке или заземляющему проводнику шинопровода до подключения фазных контактов ответвительных устройств к фазным проводникам шинопровода, или должен обеспечиваться надежный контакт металлической оболочки ответвительного устройства с металлической оболочкой шинопровода до соприкосновения фазных контактов ответвительного устройства с фазными проводниками шинопровода
[ ГОСТ 6815-79]
Ответвительную коробку вставляют через окно, при этом втычные контакты соединяют с шинами и коробка фиксируется на шинопроводе.
[ВСН 363-76]
Тематики
- изделие электромонтажное
- электропроводка, электромонтаж
Синонимы
Примечание(1) В документации Schneider ElectricСопутствующие термины
EN
FR
Франко-русский словарь нормативно-технической терминологии > élément de dérivation
-
109 socle mobile de prise de courant
переносная розетка
Розетка, предназначенная для соединения с гибким кабелем или шнуром или являющаяся частью гибкого кабеля или шнура,присоединив которую к сети можно легко перемещать с одного места на другоекоторую можно присоединить к стационарной сети и легко перемещать с одного места на другое.
[ ГОСТ Р 51322.1-99]EN
portable socket-outlet
a socket-outlet intended to be connected to, or integral with, flexible cables or cords, and which can easily be moved from one place to another while connected to the supply
[IEV number 442-03-07]FR
socle mobile de prise de courant
socle de prise de courant prévu pour être relié à, ou être intégré à, des câbles souples et qui peut être facilement déplacé lorsqu'il est relié au circuit d'alimentation
[IEV number 442-03-07]
1 - Розетка;
2 - Угловая вилка;
3 - Перносная розеткаТематики
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > socle mobile de prise de courant
-
110 adaptateur intermédiaire (pour le petit appareillage)
промежуточный адаптер (для эдектроустановочных изделий)
-
[IEV number 442-03-21]EN
intermediate adaptor (for accessories)
adaptor which allows the connection of one or more types of plug to a socket-outlet via a control device such as a dimmer, clock switch, photo-electric switch, etc., which can be either integral with the intermediate adaptor or connected to it by a flexible cable, and in which case can be either rewireable or non-rewireable
[IEV number 442-03-21]FR
adaptateur intermédiaire (pour le petit appareillage)
adaptateur qui permet la connexion d'un ou de plusieurs types de fiches à un socle de prise de courant au moyen d'un dispositif de commande tel qu'un gradateur, un interrupteur horaire, un interrupteur photoélectrique, etc., qui peut être soit partie intégrante de l'adaptateur intermédiaire soit connecté à ce dernier au moyen d'un câble souple, et qui dans ce cas peut être démontable ou non
[IEV number 442-03-21]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > adaptateur intermédiaire (pour le petit appareillage)
-
111 traversée à conducteur démontable
проходной изолятор без токопровода
-
[ ГОСТ 27744-88]EN
draw lead bushing
bushing not having an integral current-carrying conductor; a cable or other conductor may be drawn through the bushing and attached to it at one end so that it may subsequently be detached to allow the bushing to be withdrawn
[IEV number 471-02-11]FR
traversée à conducteur démontable
traversée sans conducteur solidaire; un câble ou un autre conducteur peut être introduit dans le tube central et fixé à une extrémité de façon à pouvoir être ensuite démonté afin de permettre d’enlever la traversée
[IEV number 471-02-11]
16 - Тело изолятора
19 - Полость изолятора
70 - Фланец изолятораТематики
Классификация
>>>EN
DE
- Durchführung ohne Stromleiter
- Durchsteck-Durchführung, f
FR
Франко-русский словарь нормативно-технической терминологии > traversée à conducteur démontable
-
112 isolation thermoplastique
термопластичная изоляция
изоляция из пластмассы, способной неоднократно размягчаться при нагревании и затвердевать при охлаждении в пределах установленного для данной пластмассы диапазона температур, а также неоднократно формоваться в размягченном состоянии при экструзии
[IEV number 461-02-10]EN
thermoplastic insulation
insulation made of a plastic capable of being repeatedly softened by heating and hardened by cooling through a temperature range characteristic of the plastic and, in the softened state, capable of being repeatedly shaped by extrusion
[IEV number 461-02-10]FR
isolation thermoplastique
isolation constituée d'un plastique susceptible d'être, de manière répétée, successivement ramolli par chauffage et durci par refroidissement dans un intervalle de température caractéristique du plastique considéré et, à l'état ramolli, d'être mis en forme par extrusion
[IEV number 461-02-10]Тематики
- кабели, провода...
EN
DE
- thermoplastische Isolierung, f
FR
Франко-русский словарь нормативно-технической терминологии > isolation thermoplastique
-
113 tension assignée
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Франко-русский словарь нормативно-технической терминологии > tension assignée
-
114 tension nominale
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
номинальное напряжение конденсатора
Максимальное напряжение, при котором конденсатор может работать в течение минимальной наработки в условиях, указанных в нормативно-технической документации
[ ГОСТ 21415-75]
номинальное напряжение конденсатора
Действующее значение синусоидального переменного напряжения при номинальной частоте, на которое рассчитан конденсатор. Номинальное напряжение многофазного конденсатора - значение напряжения между выводами.
[ ГОСТ 1282-88]Тематики
- конденсаторы для повыш. коэф. мощности
- конденсаторы для электронной аппаратуры
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension nominale
-
115 Un
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Франко-русский словарь нормативно-технической терминологии > Un
-
116 DDR (abréviation)
устройство дифференциального тока
УДТ
Механическое коммутационное устройство, предназначенное включать, проводить и отключать токи в нормальных рабочих условиях и вызывать размыкание контактов, когда дифференциальный ток достигает заданного значения в определенных условиях.
Примечание - Устройство дифференциального тока может быть комбинацией различных отдельных элементов, предназначенных обнаруживать и оценивать дифференциальный ток, а также включать и отключать электрический ток.
Примечание - В национальной нормативной документации вместо термина «устройство дифференциального тока» применяют термин « устройство защитного отключения».
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
устройство дифференциального тока
УДТ
Механическое коммутационное устройство или комплекс устройств, которые вызывают размыкание контактов, когда дифференциальный или несбалансированный ток достигнет заданного значения в заданных условиях.
[ ГОСТ Р 51992-2011( МЭК 61643-1: 2005)]EN
residual current device
RCD, (abbreviation)
a mechanical switching device designed to make, carry and break currents under normal service conditions and to cause the opening of the contacts when the residual current attains a given value under specified conditions
NOTE – A residual current device can be a combination of various separate elements designed to detect and evaluate the residual current and to make and break current.
[IEV number 442-05-02]FR
dispositif (de coupure) différentiel
dispositif (à courant) différentiel résiduel
DDR (abréviation)
dispositif mécanique de coupure destiné à établir, supporter et couper des courants dans les conditions de service normales et à provoquer l'ouverture des contacts quand le courant différentiel atteint, dans des conditions spécifiées, une valeur donnée
NOTE – Un dispositif de coupure différentiel peut être une combinaison de divers éléments séparés conçus pour détecter et mesurer le courant différentiel et pour établir ou interrompre le courant.
[IEV number 442-05-02]Параллельные тексты EN-RU Operating principle of residual current devices
The operating principle of residual current devices consists in the detection of an earth fault current by means of a toroidal transformer which encloses all the live conductors, included the neutral, if distributed.
In absence of an earth fault the vectorial sum of the currents IΔ is equal to zero; in case of an earth fault, if the value of IΔ exceeds the value of the trip threshold, called IΔ n, the circuit at the secondary of the toroid sends a command signal to a dedicated opening device causing the circuit-breaker tripping.
[ABB]Принцип действия устройств дифференциального тока
Принцип действия устройств дифференциального тока заключается в обнаружении тока замыкания на землю с помощью тороидального трансформатора, который охватывает все токоведущие, в том числе и нейтральный проводник, если он используется для распределения электроэнергии.
При отсутствии замыкания на землю векторная сумма токов IΔ равна нулю. Если при возникновении замыкания на землю значение IΔ превысит уставку срабатывания, обозначаемую как IΔn, то во вторичной обмотке тороидального трансформатора будет наведена ЭДС, достаточная для включения специального устройства, вызывающего срабатывание автоматического выключателя
[Перевод Интент]Тематики
- аппарат, изделие, устройство...
- электроустановки
Обобщающие термины
Синонимы
EN
- RCD, (abbreviation)
- residual current device
DE
FR
Франко-русский словарь нормативно-технической терминологии > DDR (abréviation)
-
117 dispositif (de coupure) différentiel
устройство дифференциального тока
УДТ
Механическое коммутационное устройство, предназначенное включать, проводить и отключать токи в нормальных рабочих условиях и вызывать размыкание контактов, когда дифференциальный ток достигает заданного значения в определенных условиях.
Примечание - Устройство дифференциального тока может быть комбинацией различных отдельных элементов, предназначенных обнаруживать и оценивать дифференциальный ток, а также включать и отключать электрический ток.
Примечание - В национальной нормативной документации вместо термина «устройство дифференциального тока» применяют термин « устройство защитного отключения».
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
устройство дифференциального тока
УДТ
Механическое коммутационное устройство или комплекс устройств, которые вызывают размыкание контактов, когда дифференциальный или несбалансированный ток достигнет заданного значения в заданных условиях.
[ ГОСТ Р 51992-2011( МЭК 61643-1: 2005)]EN
residual current device
RCD, (abbreviation)
a mechanical switching device designed to make, carry and break currents under normal service conditions and to cause the opening of the contacts when the residual current attains a given value under specified conditions
NOTE – A residual current device can be a combination of various separate elements designed to detect and evaluate the residual current and to make and break current.
[IEV number 442-05-02]FR
dispositif (de coupure) différentiel
dispositif (à courant) différentiel résiduel
DDR (abréviation)
dispositif mécanique de coupure destiné à établir, supporter et couper des courants dans les conditions de service normales et à provoquer l'ouverture des contacts quand le courant différentiel atteint, dans des conditions spécifiées, une valeur donnée
NOTE – Un dispositif de coupure différentiel peut être une combinaison de divers éléments séparés conçus pour détecter et mesurer le courant différentiel et pour établir ou interrompre le courant.
[IEV number 442-05-02]Параллельные тексты EN-RU Operating principle of residual current devices
The operating principle of residual current devices consists in the detection of an earth fault current by means of a toroidal transformer which encloses all the live conductors, included the neutral, if distributed.
In absence of an earth fault the vectorial sum of the currents IΔ is equal to zero; in case of an earth fault, if the value of IΔ exceeds the value of the trip threshold, called IΔ n, the circuit at the secondary of the toroid sends a command signal to a dedicated opening device causing the circuit-breaker tripping.
[ABB]Принцип действия устройств дифференциального тока
Принцип действия устройств дифференциального тока заключается в обнаружении тока замыкания на землю с помощью тороидального трансформатора, который охватывает все токоведущие, в том числе и нейтральный проводник, если он используется для распределения электроэнергии.
При отсутствии замыкания на землю векторная сумма токов IΔ равна нулю. Если при возникновении замыкания на землю значение IΔ превысит уставку срабатывания, обозначаемую как IΔn, то во вторичной обмотке тороидального трансформатора будет наведена ЭДС, достаточная для включения специального устройства, вызывающего срабатывание автоматического выключателя
[Перевод Интент]Тематики
- аппарат, изделие, устройство...
- электроустановки
Обобщающие термины
Синонимы
EN
- RCD, (abbreviation)
- residual current device
DE
FR
Франко-русский словарь нормативно-технической терминологии > dispositif (de coupure) différentiel
-
118 dispositif (à courant) différentiel résiduel
устройство дифференциального тока
УДТ
Механическое коммутационное устройство, предназначенное включать, проводить и отключать токи в нормальных рабочих условиях и вызывать размыкание контактов, когда дифференциальный ток достигает заданного значения в определенных условиях.
Примечание - Устройство дифференциального тока может быть комбинацией различных отдельных элементов, предназначенных обнаруживать и оценивать дифференциальный ток, а также включать и отключать электрический ток.
Примечание - В национальной нормативной документации вместо термина «устройство дифференциального тока» применяют термин « устройство защитного отключения».
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
устройство дифференциального тока
УДТ
Механическое коммутационное устройство или комплекс устройств, которые вызывают размыкание контактов, когда дифференциальный или несбалансированный ток достигнет заданного значения в заданных условиях.
[ ГОСТ Р 51992-2011( МЭК 61643-1: 2005)]EN
residual current device
RCD, (abbreviation)
a mechanical switching device designed to make, carry and break currents under normal service conditions and to cause the opening of the contacts when the residual current attains a given value under specified conditions
NOTE – A residual current device can be a combination of various separate elements designed to detect and evaluate the residual current and to make and break current.
[IEV number 442-05-02]FR
dispositif (de coupure) différentiel
dispositif (à courant) différentiel résiduel
DDR (abréviation)
dispositif mécanique de coupure destiné à établir, supporter et couper des courants dans les conditions de service normales et à provoquer l'ouverture des contacts quand le courant différentiel atteint, dans des conditions spécifiées, une valeur donnée
NOTE – Un dispositif de coupure différentiel peut être une combinaison de divers éléments séparés conçus pour détecter et mesurer le courant différentiel et pour établir ou interrompre le courant.
[IEV number 442-05-02]Параллельные тексты EN-RU Operating principle of residual current devices
The operating principle of residual current devices consists in the detection of an earth fault current by means of a toroidal transformer which encloses all the live conductors, included the neutral, if distributed.
In absence of an earth fault the vectorial sum of the currents IΔ is equal to zero; in case of an earth fault, if the value of IΔ exceeds the value of the trip threshold, called IΔ n, the circuit at the secondary of the toroid sends a command signal to a dedicated opening device causing the circuit-breaker tripping.
[ABB]Принцип действия устройств дифференциального тока
Принцип действия устройств дифференциального тока заключается в обнаружении тока замыкания на землю с помощью тороидального трансформатора, который охватывает все токоведущие, в том числе и нейтральный проводник, если он используется для распределения электроэнергии.
При отсутствии замыкания на землю векторная сумма токов IΔ равна нулю. Если при возникновении замыкания на землю значение IΔ превысит уставку срабатывания, обозначаемую как IΔn, то во вторичной обмотке тороидального трансформатора будет наведена ЭДС, достаточная для включения специального устройства, вызывающего срабатывание автоматического выключателя
[Перевод Интент]Тематики
- аппарат, изделие, устройство...
- электроустановки
Обобщающие термины
Синонимы
EN
- RCD, (abbreviation)
- residual current device
DE
FR
Франко-русский словарь нормативно-технической терминологии > dispositif (à courant) différentiel résiduel
-
119 ACE
Association, composée de 103 clubs provenant des divisions supérieures des associations membres de l'UEFA, dont les buts sont notamment de défendre et de promouvoir les intérêts du football interclubs européen en particulier et du football interclubs en général, d'être reconnue par l'UEFA comme la seule instance représentant les intérêts des clubs au niveau européen, de représenter les intérêts des clubs en tant qu'employeurs en Europe, y compris dans le processus de dialogue social, et d'agir, le cas échéant, en tant que partenaire social.► L'Association des clubs européennes contribue au sain développement des compétitions interclubs européennes organisées par l'UEFA en participant au processus de décision, apporte des idées concernant le calendrier international des matches, contribue à la bonne gouvernance du football européen, notamment en participant aux séances des instances appropriées au sein de l'UEFA, et favorise l'échange d'informations et de compétences entre l'UEFA et les clubs.
Syn. ACE f abrév.An association of 103 top-division clubs of UEFA member associations whose objectives are, among others, to safeguard and promote the interests of European club football, in particular, and club football in general, to be recognised by UEFA as the sole body representing the interests of clubs at European level and to represent the interests of the clubs as employers in Europe, including in the social dialogue process, and to act as a social partner where appropriate.► In addition, the European Club Association contributes to the healthy development of European club competitions organised by UEFA, by taking part in the relevant decision-making process, by providing input as regards the international match calendar, contributing to the good governance of Eurpean football, in particular by paricipating in the appropriate bodies established within UEFA, and fostering the exchange of information and expertise between UEFA and the clubs.
Syn. ECA abbr. -
120 Association des clubs européennes
Association, composée de 103 clubs provenant des divisions supérieures des associations membres de l'UEFA, dont les buts sont notamment de défendre et de promouvoir les intérêts du football interclubs européen en particulier et du football interclubs en général, d'être reconnue par l'UEFA comme la seule instance représentant les intérêts des clubs au niveau européen, de représenter les intérêts des clubs en tant qu'employeurs en Europe, y compris dans le processus de dialogue social, et d'agir, le cas échéant, en tant que partenaire social.► L'Association des clubs européennes contribue au sain développement des compétitions interclubs européennes organisées par l'UEFA en participant au processus de décision, apporte des idées concernant le calendrier international des matches, contribue à la bonne gouvernance du football européen, notamment en participant aux séances des instances appropriées au sein de l'UEFA, et favorise l'échange d'informations et de compétences entre l'UEFA et les clubs.
Syn. ACE f abrév.An association of 103 top-division clubs of UEFA member associations whose objectives are, among others, to safeguard and promote the interests of European club football, in particular, and club football in general, to be recognised by UEFA as the sole body representing the interests of clubs at European level and to represent the interests of the clubs as employers in Europe, including in the social dialogue process, and to act as a social partner where appropriate.► In addition, the European Club Association contributes to the healthy development of European club competitions organised by UEFA, by taking part in the relevant decision-making process, by providing input as regards the international match calendar, contributing to the good governance of Eurpean football, in particular by paricipating in the appropriate bodies established within UEFA, and fostering the exchange of information and expertise between UEFA and the clubs.
Syn. ECA abbr.Dictionnaire Français-Anglais (UEFA Football) > Association des clubs européennes
См. также в других словарях:
The Amazing Race 19 — Le temple de Borobudur, en Indonésie, a été visité pendant la troisième étape de cette course. Autre titre francophone La course incroyable 19, Rallye autour du monde 19 Genre … Wikipédia en Français
The Journeyman Project (series) — The Journeyman Project Trilogy Developer(s) Presto Studios Publisher(s) … Wikipedia
The Brussels Journal — is a conservative blog, founded by the Flemish journalist Paul Beliën. It was founded in 2005, and has both an English language section with various international contributions, and a Dutch section. It is published by the Society for the… … Wikipedia
The GazettE (groupe) — The GazettE The GazettE … Wikipédia en Français
The Gazette (groupe) — The GazettE The GazettE … Wikipédia en Français
The Pillows — Membres du groupe Pays d’origine … Wikipédia en Français
The pillows — Membres du groupe Pays d’origine … Wikipédia en Français
The Royals — est un groupe vocal de doo wop américain. Le quartet, composé de Henry Booth, chanteur soliste, Sonny Woods, basse, Lawson Smith, baryton, et Charles Sutton, deuxième soliste, est découvert en 1951 par Johnny Otis dans un concours de jeunes… … Wikipédia en Français
The Man Who Would Be King — L Homme qui voulut être roi L Homme qui voulut être roi Titre original The Man Who Would Be King Réalisation John Huston Acteurs principaux Sean Connery Michael Caine Christopher Plummer Scénario John Huston Gladys Hill d après Rudyard Kipling… … Wikipédia en Français
The Importance of Being Emma — De l importance d être Emma The Importance of Being Emma (littéralement : De l importance d être Emma) est un roman de Juliet Archer publié en 2008, moderne adaptation de celui de Jane Austen, Emma. Il est le premier d une série de Choc Lit… … Wikipédia en Français
The Rise and Fall of the Great Powers — Infobox Book | name = The Rise and Fall of the Great Powers author = Paul Kennedy country = United States language = English publisher = Random House release date = media type = Print (Hardback) genre = Economics, History pages = 677 isbn = ISBN… … Wikipedia