-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
Aluminum wire — is a type of wiring used in houses and power grids. History Usage within utilities Since the early 1900s, utility companies have been using aluminum wire for transmission of electricity within their power grids. It has advantages over the older… … Wikipedia
aluminum processing — Introduction preparation of the ore for use in various products. Aluminum, or aluminium (Al), is a silvery white metal with a melting point of 660° C (1,220° F) and a density of 2.7 grams per cubic centimetre. The most abundant… … Universalium
Aluminum piano plate — A piano with an aluminum piano plate, called the Alumatone plate, was created in the late 1940s by Winter and Company, piano manufacturers, and Alcoa, a manufacturer of aluminum and aluminum products. The metal frame of a piano, often called the… … Wikipedia
Aluminum Corporation of China Limited — 中国铝业 Type Public (SEHK: 2600, NYSE: ACH [1] Industry Aluminum Founded 2001 ( … Wikipedia
aluminum — (n.) 1812, coined by English chemist Sir Humphry Davy (1778 1829), from alumina, name given 18c. to aluminum oxide, from L. alumen alum (see ALUM (Cf. alum)). Davy originally called it alumium (1808), then amended this to aluminum, which remains… … Etymology dictionary
Aluminum Metal Toys — Aluminum Metal Toys, or AMT for short, is a Troy, Michigan based company that manufactures various plastic models from the late 1950s to 2005, particularly American cars and trucks in 1/25 scale.In 1981, AMT was purchased by Ertl renamed AMT Ertl … Wikipedia
Aluminum — A*lu mi*num ([.a]*l[=u]*m[i^]*n[u^]m), n. The metallic element forming the base of alumina. This metal is white, but with a bluish tinge, and is remarkable for its resistance to oxidation, and for its lightness, having a specific gravity of about … The Collaborative International Dictionary of English
aluminum sulfate — n. a white crystalline salt, Al2 (SO4) 3, made by treating bauxite or clay with sulfuric acid: it is used in sizing paper, purifying water, fixing dyes, tanning, etc … English World dictionary
aluminum — aluminic /al yeuh min ik/, adj. /euh looh meuh neuhm/, n. 1. Chem. a silver white metallic element, light in weight, ductile, malleable, and not readily corroded or tarnished, occurring combined in nature in igneous rock, shale, clay, and most… … Universalium
Aluminum bottle — An aluminum beverage bottle, also known as a bottlecan, is a bottle made entirely of 100 percent recyclable aluminum that holds beer, soft drinks, alternative beverages and wine. History Overview The aluminum beverage bottle was introduced to the … Wikipedia
Aluminum Company of America — ▪ American company (Alcoa), American corporation founded in 1888 (as the Pittsburgh Reduction Company) and now a leading producer of aluminum. Its operations range from mining bauxite and other ores to smelting and processing aluminum,… … Universalium
