-
81 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
82 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
83 courant de courte durée admissible
кратковременно допустимый ток
Ток, который цепь или коммутационный аппарат способны проводить в замкнутом положении в течение установленного кратковременного периода в заданных условиях эксплуатации и поведения.
МЭК 60050(441-17-17).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
short-time withstand current
the current that a circuit or a switching device in the closed position can carry during a specified short time under prescribed conditions of use and behaviour
[IEV number 441-17-17]FR
courant de courte durée admissible
courant qu'un circuit ou un appareil de connexion dans la position de fermeture peut supporter pendant un court intervalle de temps spécifié et dans des conditions prescrites d'emploi et de comportement
[IEV number 441-17-17]Тематики
- электротехника, основные понятия
EN
DE
FR
номинальный кратковременно выдерживаемый ток (Icw) цепи НКУ
Номинальным кратковременно выдерживаемым током цепи НКУ является действующее значение кратковременного тока, установленное для этой цепи изготовителем, который данная цепь может выдерживать без повреждений.
Для цепи переменного тока значение тока есть его действующее значение, при этом предполагают, что наибольшее значение пика тока, которое может появиться не превысит в n раз действующее значение.
(МЭС 441-17-17, с изменением)
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]Тематики
- НКУ (шкафы, пульты,...)
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant de courte durée admissible
-
84 courant de ligne
линейный ток
Ток, протекающий в линейном проводнике трехфазной электрической цепи, соединяющем источник и приемник электрической энергии.EN
phase current, I
value of the current flowing in each phase of an electrical distribution system
[IEC 61557-12, ed. 1.0 (2007-08)]FR
courant de phase, I
valeur du courant circulant dans chaque phase d’un réseau de distribution électrique
[IEC 61557-12, ed. 1.0 (2007-08)]
Четырехпроводная система трехфазного токаНейтраль - обшая точка соединенных концов фазных обмоток генератора (источника питания). То же самое относится и к потребителю (нагрузке).
Линейные провода ( проводники) - проводники, присоединенные к началу фазных обмоток (А, В и С).
Звезда ( соединение звездой) - представленное на рисунке соединение, в котором начала обмоток соединены в одну общую точку.
Нулейвой провод ( проводник) или нулевой рабочий провод (проводник) - проводник соединяющий нейтрали генератора (источника питания) и потребителя (нагрузки). Нулевой провод выполняет роль обратного провода.
Линейное напряжение - напряжение между линейными проводами.
Фазное напряжение - напряжение между линейным и нулевым проводом.
Фазный ток - ток, протекающий по фазной обмотке генератора (источника питания) или потребителя.
Линейный ток - ток, протекающий по линейному проводу.
При соединении звездой линейный ток равен фазному.
При работе по нулевому проводу протекает ток, равный векторной сумме трех линейных токов: IА, IB и IC.
Если фазы нагружены равномерно, то ток нулевого провода равен нулю.
[На основе книги Кузнецов М. И. Основы электротехники. М, "Высшая Школа", 1964]Тематики
- электротехника, основные понятия
EN
FR
Франко-русский словарь нормативно-технической терминологии > courant de ligne
-
85 courant de phase
линейный ток
Ток, протекающий в линейном проводнике трехфазной электрической цепи, соединяющем источник и приемник электрической энергии.EN
phase current, I
value of the current flowing in each phase of an electrical distribution system
[IEC 61557-12, ed. 1.0 (2007-08)]FR
courant de phase, I
valeur du courant circulant dans chaque phase d’un réseau de distribution électrique
[IEC 61557-12, ed. 1.0 (2007-08)]
Четырехпроводная система трехфазного токаНейтраль - обшая точка соединенных концов фазных обмоток генератора (источника питания). То же самое относится и к потребителю (нагрузке).
Линейные провода ( проводники) - проводники, присоединенные к началу фазных обмоток (А, В и С).
Звезда ( соединение звездой) - представленное на рисунке соединение, в котором начала обмоток соединены в одну общую точку.
Нулейвой провод ( проводник) или нулевой рабочий провод (проводник) - проводник соединяющий нейтрали генератора (источника питания) и потребителя (нагрузки). Нулевой провод выполняет роль обратного провода.
Линейное напряжение - напряжение между линейными проводами.
Фазное напряжение - напряжение между линейным и нулевым проводом.
Фазный ток - ток, протекающий по фазной обмотке генератора (источника питания) или потребителя.
Линейный ток - ток, протекающий по линейному проводу.
При соединении звездой линейный ток равен фазному.
При работе по нулевому проводу протекает ток, равный векторной сумме трех линейных токов: IА, IB и IC.
Если фазы нагружены равномерно, то ток нулевого провода равен нулю.
[На основе книги Кузнецов М. И. Основы электротехники. М, "Высшая Школа", 1964]Тематики
- электротехника, основные понятия
EN
FR
Франко-русский словарь нормативно-технической терминологии > courant de phase
-
86 courant présumé (d'un circuit et relatif à un appareil de connexion ou à un fusible)
- ожидаемый ток цепи (по отношению к коммутационному аппарату или плавкому предохранителю)
ожидаемый ток цепи (по отношению к коммутационному аппарату или плавкому предохранителю)
Ток, который протекал бы в цепи, если бы каждый полюс коммутационного аппарата или плавкого предохранителя был заменен проводником с пренебрежимо малым полным сопротивлением.
МЭК 60050(441-17-01).
Примечание. Метод оценки и выражения ожидаемого тока должен быть уточнен в соответствующем стандарте на аппарат.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
prospective current (of a circuit and with respect to a switching device or a fuse)
current that would flow in the circuit if each pole of the switching device or the fuse were replaced by a conductor of negligible impedance.
NOTE - The method to be used to evaluate and to express the prospective current is to be specified in the relevant publications.
[IEC 61095, ed. 2.0 (2009-02)]FR
courant présumé (d'un circuit et relatif à un appareil de connexion ou à un fusible)
courant qui circulerait dans le circuit si chaque pôle de l'appareil de connexion ou le fusible était remplacé par un conducteur d'impédance négligeable
NOTE - La méthode à employer pour évaluer et pour exprimer le courant présumé doit être spécifiée dans les publications correspondantes.
[IEC 61095, ed. 2.0 (2009-02)]Тематики
- выключатель автоматический
- выключатель, переключатель
EN
- prospective current (of a circuit and with respect to a switching device or a fuse)
DE
- unbeeinflußter Strom (in einem Stromkreis in bezug auf ein Schaltgerät oder eine Sicherung)
FR
- courant présumé (d'un circuit et relatif à un appareil de connexion ou à un fusible)
Франко-русский словарь нормативно-технической терминологии > courant présumé (d'un circuit et relatif à un appareil de connexion ou à un fusible)
-
87 courant d'excitation
ток намагничивания трансформатора тока
Действующее значение тока, потребляемого вторичной обмоткой трансформатора тока, когда ко вторичным зажимам подведено синусоидальное напряжение номинальной частоты, причем первичная обмотка и все остальные обмотки разомкнуты.
[ ГОСТ 18685-73]EN
exciting current
the r.m.s. value of the current taken by the secondary winding of a current transformer, when a sinusoidal voltage of rated frequency is applied to the secondary terminals, the primary and any other windings being open-circuited
[IEV number 321-02-32]FR
courant d'excitation
valeur efficace du courant qui traverse l'enroulement secondaire d'un transformateur de courant, lorsqu'on applique entre les bornes secondaires une tension sinusoïdale à la fréquence assignée, l'enroulement primaire et tous les autres enroulements étant à circuit ouvert
[IEV number 321-02-32]Недопустимые, нерекомендуемые
EN
DE
- Erregerstrom, sekundärer
- sekundärer Erregerstrom
FR
Франко-русский словарь нормативно-технической терминологии > courant d'excitation
-
88 courant coupé limité
ток отсечки
Максимальное мгновенное значение тока, достигаемое в процессе отключения тока коммутационным аппаратом или плавким предохранителем.
МЭК 60050 (441-17-12).
Примечание. Понятие особенно важно, когда коммутационный аппарат или плавкий предохранитель срабатывает так, что ожидаемый пиковый ток цепи не достигается.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
cut-off current
let-through current
the maximum instantaneous value of current attained during the breaking operation of a switching device or a fuse
NOTE – This concept of particular importance when the switching device or the fuse operates in such a manner that the prospective peak current of the circuit is not reached.
[IEV number 441-17-12]FR
courant coupé limité
valeur instantanée maximale du courant atteinte au cours de la coupure effectuée par un appareil de connexion ou un fusible
NOTE – Cette notion est d'importance particulière si l'appareil de connexion ou le fusible fonctionne de telle manière que la valeur de crête du courant présumé du circuit n'est pas atteinte.
[IEV number 441-17-12]Примечание
Более подробно о токе отсечки см. " защитная характеристика автоматического выключателя"Тематики
- выключатель автоматический
- выключатель, переключатель
- предохранитель
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant coupé limité
-
89 courant de base
базовый ток
-
[IEV number 314-07-01]EN
basic current
value of current in accordance with which the relevant performance of a direct connected meter is fixed
[IEV number 314-07-01]FR
courant de base
valeur du courant en fonction de laquelle certaines des caractéristiques d’un compteur à branchement direct sont fixées
[IEV number 314-07-01]Тематики
- измерение электр. величин в целом
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant de base
-
90 courant vagabond
блуждающий ток
Ток утечки в земле или металлических конструкциях, находящихся в земле вследствие их преднамеренного или непреднамеренного заземления.
[ ГОСТ Р МЭК 60050-195-2005]
блуждающий ток
Ток утечки электрических установок постоянного тока, протекающий в земле и в подземных металлических сооружениях.
[ ГОСТ Р 50889-96]
блуждающие токи
земляные токи
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]EN
stray current
leakage current in the Earth or in metallic structures buried in the ground and resulting from their intended or unintended earthing
Source: 604-04-14 MOD
[IEV number 195-05-16]FR
courant vagabond
courant de fuite dans la Terre ou dans des structures métalliques enterrées, et qui résulte de leur mise à la terre, intentionnelle ou non
Source: 604-04-14 MOD
[IEV number 195-05-16]Тематики
- электротехника, основные понятия
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant vagabond
-
91 courant différentiel résiduel
дифференциальный ток
Алгебраическая сумма значений электрических токов во всех токоведущих проводниках в одно и то же время в данной точке электрической цепи электрической установки
[ ГОСТ Р МЭК 60050-826-2009]
Примечание - Определение термина «дифференциальный ток» в МЭК 60050-826 [4] сформулировано для электрической цепи. Через главную цепь устройства дифференциального тока, защищающего электрическую цепь, проходят все ее проводники, находящиеся под напряжением, вследствие чего дифференциальный ток, появляющийся в электрической цепи, будет равен дифференциальному току, определяемому устройством дифференциального тока.
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
дифференциальный ток
IΔ,
Действующее значение векторной суммы токов, протекающих в главной цепи.
дифференциальный ток
ID
Среднеквадратическое значение векторной суммы токов, протекающих через главную цепь устройства дифференциального тока.
П р и м е ч а н и е - Определение термина «дифференциальный ток» в МЭК 60050-442 [6] сформулировано для устройства дифференциального тока.
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
дифференциальный ток
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]EN
residual current
algebraic sum of the values of the electric currents in all live conductors, at the same time at a given point of an electric circuit in an electrical installation
[IEV number 826-11-19]
residual current
r.m.s. value of the vector sum of the currents flowing through the main circuit of the residual current device
[IEV number 442-05-19]FR
courant différentiel résiduel, m
somme algébrique des valeurs des courants électriques dans tous les conducteurs actifs, au même instant en un point donné d'un circuit électrique d'une installation électrique
[IEV number 826-11-19]
courant différentiel résiduel
valeur efficace de la somme vectorielle des courants circulant dans le circuit principal du dispositif de coupure différentiel
[IEV number 442-05-19]Недопустимые, нерекомендуемые
Тематики
- электробезопасность
- электротехника, основные понятия
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant différentiel résiduel
-
92 courant maximal admissible
допустимый длительный ток кабеля (провода)
-
[Интент]
допустимый длительный ток (проводника)
Максимальный электрический ток, который проводник способен проводить в продолжительном режиме без превышения его установившейся температурой определённого значения.
Допустимый длительный ток является одной из основных характеристик проводника. Он представляет собой максимальный электрический ток, который проводник может проводить длительно (неделями, месяцами, годами) не перегреваясь. Значение допустимого длительного тока зависит от сечения проводника, материалов из которых выполнены проводник и его изоляция, способов монтажа проводника в электроустановке здания. Допустимый длительный ток проводника фактически является его номинальным током. В электроустановках зданий выполняют защиту проводников от сверхтоков, протекание которых по проводникам сопровождается их перегревом.
[ http://www.volt-m.ru/glossary/letter/%C4/view/11/]EN
current carrying capacity
maximum current a cable circuit (one or several conductors) can support resulting in a specified increase of the surface temperature of the conductor beyond the ambient temperature, not exceeding the maximum allowed operating temperature of the cable
[IEC 61156-1, ed. 3.0 (2007-06< size="2">)]FR
courant maximal admissible
courant maximal qu’un circuit de câble (un ou plusieurs conducteurs) peut supporter avec une augmentation spécifiée de la température de surface du conducteur au delà de la température ambiante, et ne dépassant pas la température maximale de fonctionnement autorisée du câble
[IEC 61156-1, ed. 3.0 (2007-06< size="2">)]Номинальный ток устройств защиты от короткого замыкания может превышать допустимый длительный ток кабеля.
[ ГОСТ Р 50571. 5-94 ( МЭК 364-4-43-77)]Допустимые длительные токи для проводов и кабелей, проложенных в коробах, а также в лотках пучками, должны приниматься...
[ПУЭ]Тематики
- кабели, провода...
- электроустановки
EN
- ampere capacity
- current carrying capacity
- current carrying capacity of the cable
- current carrying capacity of the conductors
- current-carrying capacity of the cable
FR
Франко-русский словарь нормативно-технической терминологии > courant maximal admissible
-
93 courant de choc de manœuvre d'un parafoudre
коммутационный импульс тока ОПН
Максимальное (амплитудное) значение тока с условной длительностью фронта не менее 30, но не более 100 мкс и условной длительностью импульса, равной удвоенному времени условного фронта импульса.
[ ГОСТ Р 52725-2007]EN
switching current impulse of an arrester
peak value of discharge current having a virtual front time greater than 30 ms but less than 100 ms and a virtual time to half-value on the tail of roughly twice the virtual front time
[IEC 60099-4, ed. 2.0 (2004-05)]FR
courant de choc de manœuvre d'un parafoudre
valeur de crête du courant de décharge dont la durée conventionnelle du front est comprise entre 30 ms et 100 ms, et dont la durée conventionnelle jusqu'à mi-valeur sur la queue est d'environ deux fois la durée conventionnelle du front
[IEC 60099-4, ed. 2.0 (2004-05)]Тематики
- высоковольтный аппарат, оборудование...
EN
FR
Франко-русский словарь нормативно-технической терминологии > courant de choc de manœuvre d'un parafoudre
-
94 courant commutable
коммутируемый ток магнитоуправляемого контакта
-
[ ГОСТ 17499-82]Тематики
Обобщающие термины
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant commutable
-
95 courant commuté
коммутируемый ток магнитоуправляемого контакта
-
[ ГОСТ 17499-82]Тематики
Обобщающие термины
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant commuté
-
96 courant de commutation
коммутируемый ток магнитоуправляемого контакта
-
[ ГОСТ 17499-82]Тематики
Обобщающие термины
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant de commutation
-
97 courant critique de court-circuit
критический ток короткого замыкания
Значение тока отключения ниже номинальной наибольшей отключающей способности, при котором энергия дуги значительно выше, чем при номинальной наибольшей отключающей способности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
critical short-circuit current
value of breaking current, less than the rated short-circuit breaking capacity, at which the arc energy is significantly higher than at the rated short-circuit breaking capacity
[IEC 60947-1, ed. 5.0 (2007-06)]FR
courant critique de court-circuit
valeur de courant coupé inférieure au pouvoir assigné de coupure en court-circuit, à laquelle l'énergie d'arc est notablement plus grande qu'au pouvoir assigné coupure en court-circuit
[IEC 60947-1, ed. 5.0 (2007-06)]Тематики
- выключатель автоматический
- выключатель, переключатель
- электротехника, основные понятия
EN
FR
Франко-русский словарь нормативно-технической терминологии > courant critique de court-circuit
-
98 courant critique de charge
критический ток нагрузки
Значение тока отключения в пределах диапазона условий эксплуатации, при котором время дуги заметно увеличивается.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
critical load current
value of breaking current, within the range of service conditions, at which the arcing time is significantly extended
[IEC 60947-1, ed. 5.0 (2007-06)]FR
courant critique de charge
valeur de courant coupé, dans le domaine des conditions de service, à laquelle la durée d'arc est notablement étendue
[IEC 60947-1, ed. 5.0 (2007-06)]Тематики
- выключатель автоматический
- выключатель, переключатель
- электротехника, основные понятия
EN
FR
Франко-русский словарь нормативно-технической терминологии > courant critique de charge
-
99 courant partiel de court-circuit
местный ток короткого замыкания
Электрический ток в данной точке электрической сети, вызванный коротким замыканием в другой точке этой сети.
[ ГОСТ Р МЭК 60050-195-2005]EN
partial short-circuit current
electric current at a given point of a network resulting from a short-circuit at another point of the same network
Source: 603-02-26 MOD
[IEV number 195-05-17]FR
courant partiel de court-circuit
courant électrique en un point donné d'un réseau, dû à un court-circuit en un autre point de ce réseau
Source: 603-02-26 MOD
[IEV number 195-05-17]EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant partiel de court-circuit
-
100 courant partiel de défaut série
местный ток при нарушении непрерывности цепи
Электрический ток в данной точке электрической сети, вызванный нарушением непрерывности проводника в другой точке этой сети.
[ ГОСТ Р МЭК 60050-195-2005]EN
partial (conductor) continuity fault current
electric current at a given point of a network and resulting from a conductor continuity fault at another point of the same network
Source: 603-02-25 MOD
[IEV number 195-05-19]FR
courant partiel de défaut série
courant électrique en un point d'un réseau, dû à un défaut série en un autre point de ce réseau
Source: 603-02-25 MOD
[IEV number 195-05-19]EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > courant partiel de défaut série
См. также в других словарях:
Courant Institute of Mathematical Sciences — (CIMS) Established 1935 Type Private Academic staff 82 … Wikipedia
courant — courant, ante (kou ran, rant t ) adj. 1° Qui court. Adverbialement. Tout courant, en grande hâte. Elle envoie tout courant savoir de Mme du Châtelet, si S. • M. [le roi de Prusse] passera, VOLT. Roi de Prusse, 14. Tout courant, sans… … Dictionnaire de la Langue Française d'Émile Littré
Courant De Court-circuit — Le courant de court circuit d un générateur de tension parfait est, en théorie, infini. Fort heureusement, en pratique, la valeur du courant de court circuit est finie, limitée par les impédances internes de la source, des divers tronçons de… … Wikipédia en Français
Courant De Marée — Pour les articles homonymes, voir Courant. Le raz de Sein (France) est un passage que le courant de marée rend particulièrement dangereux Le courant de marée … Wikipédia en Français
Courant de maree — Courant de marée Pour les articles homonymes, voir Courant. Le raz de Sein (France) est un passage que le courant de marée rend particulièrement dangereux Le courant de marée … Wikipédia en Français
Courant electrique — Courant électrique Pour les articles homonymes, voir Courant. Un courant électrique est un déplacement d ensemble de porteurs de charge électrique, généralement des électrons, au sein d un matériau conducteur. Ces déplacements sont imposés par l… … Wikipédia en Français
Courant Électrique — Pour les articles homonymes, voir Courant. Un courant électrique est un déplacement d ensemble de porteurs de charge électrique, généralement des électrons, au sein d un matériau conducteur. Ces déplacements sont imposés par l action de la force… … Wikipédia en Français
Courant-jet de barrière — Courant jet Représentation du Courant jet Un courant jet[1] (en anglais : jet stream) est un flux d air rapide et confiné que l on trouve dans l … Wikipédia en Français
Courant-jet de bas niveau — Courant jet Représentation du Courant jet Un courant jet[1] (en anglais : jet stream) est un flux d air rapide et confiné que l on trouve dans l … Wikipédia en Français
Courant jet — Représentation du Courant jet Un courant jet[1] (en anglais : jet stream) est un flux d air rapide et confiné que l on trouve dans l … Wikipédia en Français
Courant Alternatif — Pour les articles homonymes, voir Courant alternatif (revue). Le courant alternatif (qui peut être abrégé par CA, ou AC, pour Alternating Current en anglais, étant cependant souvent utilisé) est un courant électrique qui change de sens. Ce… … Wikipédia en Français