(between+wheels)

SUBJECT AREA: Broadcasting, Electronics and information technology, Recording

[br]

[br]

[br]

After education in Hungary and a period as an assistant at the Technische Hochschule, Berlin, Goldmark moved to England, where he joined Pye of Cambridge and worked on an experimental thirty-line television system using a cathode ray tube (CRT) for the display. In 1936 he moved to the USA to work at Columbia Broadcasting Laboratories. There, with monochrome television based on the CRT virtually a practical proposition, he devoted his efforts to finding a way of producing colour TV images: in 1940 he gave his first demonstration of a working system. There then followed a series of experimental field-sequential colour TV systems based on segmented red, green and blue colour wheels and drums, where the problem was to find an acceptable compromise between bandwidth, resolution, colour flicker and colour-image breakup. Eventually he arrived at a system using a colour wheel in combination with a CRT containing a panchromatic phosphor screen, with a scanned raster of 405 lines and a primary colour rate of 144 fields per second. Despite the fact that the receivers were bulky, gave relatively poor, dim pictures and used standards totally incompatible with the existing 525-line, sixty fields per second interlaced monochrome (black and white) system, in 1950 the Federal Communications Commission (FCC), anxious to encourage postwar revival of the industry, authorized the system for public broadcasting. Within eighteen months, however, bowing to pressure from the remainder of the industry, which had formed its own National Television Systems Committee (NTSC) to develop a much more satisfactory, fully compatible system based on the RCA three-gun shadowmask CRT, the FCC withdrew its approval.

While all this was going on, Goldmark had also been working on ideas for overcoming the poor reproduction, noise quality, short playing-time (about four minutes) and limited robustness and life of the long-established 78 rpm 12 in. (30 cm) diameter shellac gramophone record. The recent availability of a new, more robust, plastic material, vinyl, which had a lower surface noise, enabled him in 1948 to reduce the groove width some three times to 0.003 in. (0.0762 mm), use a more lightly loaded synthetic sapphire stylus and crystal transducer with improved performance, and reduce the turntable speed to 33 1/3 rpm, to give thirty minutes of high-quality music per side. This successful development soon led to the availability of stereophonic recordings, based on the ideas of Alan Blumlein at EMI in the 1930s.

In 1950 Goldmark became a vice-president of CBS, but he still found time to develop a scan conversion system for relaying television pictures to Earth from the Lunar Orbiter spacecraft. He also almost brought to the market a domestic electronic video recorder (EVR) system based on the thermal distortion of plastic film by separate luminance and coded colour signals, but this was overtaken by the video cassette recorder (VCR) system, which uses magnetic tape.

[br]

See also: Baird, John Logie

SUBJECT AREA: Land transport, Railways and locomotives, Steam and internal combustion engines

[br]

[br]

[br]

By the mid-1840s Joy was Chief Draughtsman at E.B.Wilson's locomotive works at Leeds. During that period, attempts by engineers to design ever larger and more powerful locomotives were producing ungainly types, such as the long-boiler and the Cramp ton, which were to prove blind alleys in locomotive development. Joy rediscovered the proper route with his Jenny Lind 2–2–2, built in 1847. His locomotive had minimal overhang, with the firebox between the driving and trailing axles; the driving axle supported inside frames which stopped short at the firebox, allowing the latter to be wide, while leading and trailing wheels were held by outside plate frames which had a degree of elasticity. The boiler was low-pitched, the steam pressure high at 120 psi (8.4 kg/cm²). The result was a powerful locomotive which rode well and immediately became popular, a forerunner of many later designs. Joy subsequently had a varied career with successive railways and engineering firms. In the late 1850s he invented steam reversing gear for large, marine steam engines, a hydraulic organ blower and a pneumatic hammer. In 1879 he invented his radial valve gear for steam engines, which was adopted by F.W. Webb for the London \& North Western Railway's locomotives and was also much used in marine steam engines.

[br]

SUBJECT AREA: Land transport, Railways and locomotives

[br]

[br]

[br]

Mallet's family moved to Normandy while he was still a child. After working as a civil engineer, in 1867 he turned to machinery, particularly to compound steam engines. He designed the first true compound steam locomotives, which were built for the Bayonne- Biarritz Railway in 1876. They were 0–4–2 tank locomotives with one high-pressure and one low-pressure cylinder. A starting valve controlled by the driver admitted high-pressure steam to the low-pressure cylinder while the high-pressure cylinder exhausted to the atmosphere. At that time it was thought impracticable in a narrow-gauge locomotive to have more than three coupled axles in rigid frames. Mallet patented his system of articulation in 1884 and the first locomotives were built to that design in 1888: they were 0–4–4–0 tanks with two sets of frames. The two rear pairs of wheels carried the rear set of frames and were driven by two high-pressure cylinders; the two front pairs, which were driven by the high-pressure cylinders, carried a separate set of frames that was allowed sideplay, with a centre of rotation between the low-pressure cylinders. In contrast to the patent locomotive of Robert Fairlie, no flexible connections were required to carry steam at boiler pressure. The first Mallet articulated locomotives were small, built to 60 cm (23.6 in.) gauge: the first standard-gauge Mallets were built in 1890, for the St Gotthard Railway, and it was only after the type was adopted by American railways in 1904 that large Mallet locomotives were built, with sizes increasing rapidly to culminate in some of the largest steam locomotives ever produced. In the late 1880s Mallet also designed monorail locomotives, which were built for the system developed by C.F.M.-T. Lartigue.

[br]

See also: Bousquet, Gaston du; Vauclain, Samuel Matthews; Webb, Francis William

SUBJECT AREA: Agricultural and food technology

[br]

[br]

[br]

The son of the millwright James Meikle, who is credited with the introduction of the winnowing machine into Britain, Andrew Meikle followed in his father's footsteps. His inventive inclinations were first turned to developing his father's idea, and together with his own son George he built and patented a double-fan winnowing machine.

However, in the history of agricultural development Andrew Meikle is most famous for his invention of the threshing machine, patented in 1784. He had been presented with a model of a threshing mill designed by a Mr Ilderton of Northumberland, but after failing to make a full-scale machine work, he developed the concept further. He eventually built the first working threshing machine for a farmer called Stein at Kilbagio. The patent revolutionized farming practice because it displaced the back-breaking and soul-destroying labour of flailing the grain from the straw. The invention was of great value in Scotland and in northern England when the land was becoming underpopulated as a result of heavy industrialization, but it was bitterly opposed in the south of England until well into the nineteenth century. Although the introduction of the threshing machine led to the "Captain Swing" riots of the 1830s, in opposition to it, it shortly became universal.

Meikle's provisional patent in 1785 was a natural progression of earlier attempts by other millwrights to produce such a machine. The published patent is based on power provided by a horse engine, but these threshing machines were often driven by water-wheels or even by windmills. The corn stalks were introduced into the machine where they were fed between cast-iron rollers moving quite fast against each other to beat the grain out of the ears. The power source, whether animal, water or wind, had to cause the rollers to rotate at high speed to knock the grain out of the ears. While Meikle's machine was at first designed as a fixed barn machine powered by a water-wheel or by a horse wheel, later threshing machines became mobile and were part of the rig of an agricultural contractor.

In 1788 Meikle was awarded a patent for the invention of shuttered sails for windmills. This patent is part of the general description of the threshing machine, and whilst it was a practical application, it was superseded by the work of Thomas Cubitt.

At the turn of the century Meikle became a manufacturer of threshing machines, building appliances that combined the threshing and winnowing principles as well as the reciprocating "straw walkers" found in subsequent threshing machines and in conventional combine harvesters to the present day. However, he made little financial gain from his invention, and a public subscription organized by the President of the Board of Agriculture, Sir John Sinclair, raised £1,500 to support him towards the end of his life.

[br]

KM / AP

SUBJECT AREA: Railways and locomotives, Steam and internal combustion engines

[br]

[br]

[br]

Seguin trained under Joseph Montgolfier, one of the inventors of the hot-air balloon, and became a pioneer of suspension bridges. In 1825 he was involved in an attempt to introduce steam navigation to the River Rhône using a tug fitted with a winding drum to wind itself upstream along a cable attached to a point on the bank, with a separate boat to transfer the cable from point to point. The attempt proved unsuccessful and was short-lived, but in 1825 Seguin had decided also to seek a government concession for a railway from Saint-Etienne to Lyons as a feeder of traffic to the river. He inspected the Stockton \& Darlington Railway and met George Stephenson; the concession was granted in 1826 to Seguin Frères \& Ed. Biot and two steam locomotives were built to their order by Robert Stephenson \& Co. The locomotives were shipped to France in the spring of 1828 for evaluation prior to construction of others there; each had two vertical cylinders, one each side between front and rear wheels, and a boiler with a single large-diameter furnace tube, with a watertube grate. Meanwhile, in 1827 Seguin, who was still attempting to produce a steamboat powerful enough to navigate the fast-flowing Rhône, had conceived the idea of increasing the heating surface of a boiler by causing the hot gases from combustion to pass through a series of tubes immersed in the water. He was soon considering application of this type of boiler to a locomotive. He applied for a patent for a multi-tubular boiler on 12 December 1827 and carried out numerous experiments with various means of producing a forced draught to overcome the perceived obstruction caused by the small tubes. By May 1829 the steam-navigation venture had collapsed, but Seguin had a locomotive under construction in the workshops of the Lyons-Sain t- Etienne Railway: he retained the cylinder layout of its Stephenson locomotives, but incorporated a boiler of his own design. The fire was beneath the barrel, surrounded by a water-jacket: a single large flue ran towards the front of the boiler, whence hot gases returned via many small tubes through the boiler barrel to a chimney above the firedoor. Draught was provided by axle-driven fans on the tender.

Seguin was not aware of the contemporary construction of Rocket, with a multi-tubular boiler, by Robert Stephenson; Rocket had its first trial run on 5 September 1829, but the precise date on which Seguin's locomotive first ran appears to be unknown, although by 20 October many experiments had been carried out upon it. Seguin's concept of a multi-tubular locomotive boiler therefore considerably antedated that of Henry Booth, and his first locomotive was completed about the same date as Rocket. It was from Rocket's boiler, however, rather than from that of Seguin's locomotive, that the conventional locomotive boiler was descended.

[br]

SUBJECT AREA: Land transport, Railways and locomotives

[br]

[br]

[br]

George Stephenson was the son of the fireman of the pumping engine at Wylam colliery, and horses drew wagons of coal along the wooden rails of the Wylam wagonway past the house in which he was born and spent his earliest childhood. While still a child he worked as a cowherd, but soon moved to working at coal pits. At 17 years of age he showed sufficient mechanical talent to be placed in charge of a new pumping engine, and had already achieved a job more responsible than that of his father. Despite his position he was still illiterate, although he subsequently learned to read and write. He was largely self-educated.

In 1801 he was appointed Brakesman of the winding engine at Black Callerton pit, with responsibility for lowering the miners safely to their work. Then, about two years later, he became Brakesman of a new winding engine erected by Robert Hawthorn at Willington Quay on the Tyne. Returning collier brigs discharged ballast into wagons and the engine drew the wagons up an inclined plane to the top of "Ballast Hill" for their contents to be tipped; this was one of the earliest applications of steam power to transport, other than experimentally.

In 1804 Stephenson moved to West Moor pit, Killingworth, again as Brakesman. In 1811 he demonstrated his mechanical skill by successfully modifying a new and unsatisfactory atmospheric engine, a task that had defeated the efforts of others, to enable it to pump a drowned pit clear of water. The following year he was appointed Enginewright at Killingworth, in charge of the machinery in all the collieries of the "Grand Allies", the prominent coal-owning families of Wortley, Liddell and Bowes, with authorization also to work for others. He built many stationary engines and he closely examined locomotives of John Blenkinsop's type on the Kenton \& Coxlodge wagonway, as well as those of William Hedley at Wylam.

It was in 1813 that Sir Thomas Liddell requested George Stephenson to build a steam locomotive for the Killingworth wagonway: Blucher made its first trial run on 25 July 1814 and was based on Blenkinsop's locomotives, although it lacked their rack-and-pinion drive. George Stephenson is credited with building the first locomotive both to run on edge rails and be driven by adhesion, an arrangement that has been the conventional one ever since. Yet Blucher was far from perfect and over the next few years, while other engineers ignored the steam locomotive, Stephenson built a succession of them, each an improvement on the last.

During this period many lives were lost in coalmines from explosions of gas ignited by miners' lamps. By observation and experiment (sometimes at great personal risk) Stephenson invented a satisfactory safety lamp, working independently of the noted scientist Sir Humphry Davy who also invented such a lamp around the same time.

In 1817 George Stephenson designed his first locomotive for an outside customer, the Kilmarnock \& Troon Railway, and in 1819 he laid out the Hetton Colliery Railway in County Durham, for which his brother Robert was Resident Engineer. This was the first railway to be worked entirely without animal traction: it used inclined planes with stationary engines, self-acting inclined planes powered by gravity, and locomotives.

On 19 April 1821 Stephenson was introduced to Edward Pease, one of the main promoters of the Stockton \& Darlington Railway (S \& DR), which by coincidence received its Act of Parliament the same day. George Stephenson carried out a further survey, to improve the proposed line, and in this he was assisted by his 18-year-old son, Robert Stephenson, whom he had ensured received the theoretical education which he himself lacked. It is doubtful whether either could have succeeded without the other; together they were to make the steam railway practicable.

At George Stephenson's instance, much of the S \& DR was laid with wrought-iron rails recently developed by John Birkinshaw at Bedlington Ironworks, Morpeth. These were longer than cast-iron rails and were not brittle: they made a track well suited for locomotives. In June 1823 George and Robert Stephenson, with other partners, founded a firm in Newcastle upon Tyne to build locomotives and rolling stock and to do general engineering work: after its Managing Partner, the firm was called Robert Stephenson \& Co.

In 1824 the promoters of the Liverpool \& Manchester Railway (L \& MR) invited George Stephenson to resurvey their proposed line in order to reduce opposition to it. William James, a wealthy land agent who had become a visionary protagonist of a national railway network and had seen Stephenson's locomotives at Killingworth, had promoted the L \& MR with some merchants of Liverpool and had carried out the first survey; however, he overreached himself in business and, shortly after the invitation to Stephenson, became bankrupt. In his own survey, however, George Stephenson lacked the assistance of his son Robert, who had left for South America, and he delegated much of the detailed work to incompetent assistants. During a devastating Parliamentary examination in the spring of 1825, much of his survey was shown to be seriously inaccurate and the L \& MR's application for an Act of Parliament was refused. The railway's promoters discharged Stephenson and had their line surveyed yet again, by C.B. Vignoles.

The Stockton \& Darlington Railway was, however, triumphantly opened in the presence of vast crowds in September 1825, with Stephenson himself driving the locomotive Locomotion, which had been built at Robert Stephenson \& Co.'s Newcastle works. Once the railway was at work, horse-drawn and gravity-powered traffic shared the line with locomotives: in 1828 Stephenson invented the horse dandy, a wagon at the back of a train in which a horse could travel over the gravity-operated stretches, instead of trotting behind.

Meanwhile, in May 1826, the Liverpool \& Manchester Railway had successfully obtained its Act of Parliament. Stephenson was appointed Engineer in June, and since he and Vignoles proved incompatible the latter left early in 1827. The railway was built by Stephenson and his staff, using direct labour. A considerable controversy arose c. 1828 over the motive power to be used: the traffic anticipated was too great for horses, but the performance of the reciprocal system of cable haulage developed by Benjamin Thompson appeared in many respects superior to that of contemporary locomotives. The company instituted a prize competition for a better locomotive and the Rainhill Trials were held in October 1829.

Robert Stephenson had been working on improved locomotive designs since his return from America in 1827, but it was the L \& MR's Treasurer, Henry Booth, who suggested the multi-tubular boiler to George Stephenson. This was incorporated into a locomotive built by Robert Stephenson for the trials: Rocket was entered by the three men in partnership. The other principal entrants were Novelty, entered by John Braithwaite and John Ericsson, and Sans Pareil, entered by Timothy Hackworth, but only Rocket, driven by George Stephenson, met all the organizers' demands; indeed, it far surpassed them and demonstrated the practicability of the long-distance steam railway. With the opening of the Liverpool \& Manchester Railway in 1830, the age of railways began.

Stephenson was active in many aspects. He advised on the construction of the Belgian State Railway, of which the Brussels-Malines section, opened in 1835, was the first all-steam railway on the European continent. In England, proposals to link the L \& MR with the Midlands had culminated in an Act of Parliament for the Grand Junction Railway in 1833: this was to run from Warrington, which was already linked to the L \& MR, to Birmingham. George Stephenson had been in charge of the surveys, and for the railway's construction he and J.U. Rastrick were initially Principal Engineers, with Stephenson's former pupil Joseph Locke under them; by 1835 both Stephenson and Rastrick had withdrawn and Locke was Engineer-in-Chief. Stephenson remained much in demand elsewhere: he was particularly associated with the construction of the North Midland Railway (Derby to Leeds) and related lines. He was active in many other places and carried out, for instance, preliminary surveys for the Chester \& Holyhead and Newcastle \& Berwick Railways, which were important links in the lines of communication between London and, respectively, Dublin and Edinburgh.

He eventually retired to Tapton House, Chesterfield, overlooking the North Midland. A man who was self-made (with great success) against colossal odds, he was ever reluctant, regrettably, to give others their due credit, although in retirement, immensely wealthy and full of honour, he was still able to mingle with people of all ranks.

[br]

SUBJECT AREA: Textiles

[br]

[br]

[br]

Townsend, who described himself in his first patent as a framework knitter and afterwards as a hosier of Leicester, took out a patent in 1847 for the application of a "machine like that of a point net frame to an ordinary stocking-frame". He described needles and hooks of a peculiar shape which were able to take the work off the knitting machine, reverse the loops and return them again so that ribbed knitting could be made on circular machines. These became popular for knitting stockings which, although not fully fashioned, had sufficient strength to fit the leg. In 1854 he took out a patent for making round hose with heels and toes fashioned on other machines. In yet another patent, in 1856, he described a method of raising looped pile on knitted fabrics for making "terry" towelling fabrics. He could use different coloured yarns in the fabric that were controlled by a Jacquard mechanism. It was in the same year, 1856, in a further patent that he described his tumbler or latch needles as well as the making of figured patterns in knitting on both sides of the fabric with a Jacquard mechanism. The latch needles were self-acting, being made to move up and down or backwards and forwards by the action of cams set in the cylindrical body of the machine. Normally the needle worked in a vertical or inclined position with the previous loop on the shank below the latch. Weft yarn was placed in the hook of the needle. The needle was drawn down between fixed plates which formed a new loop with the weft. At the same time, the original loop already on the shank of the needle moved along the shank and closed the latch so that it could pass over the newly formed loop in the needle hook and fall over the end of the needle incorporating the new loop on its way to make the next row of stitches. The latch needle obviated the need for loop wheels and pressers and thus simplified the knitting mechanism. Townsend's invention was the forerunner of an entirely new generation of knitting machines, but it was many years before its full potential was realized, the bearded needle of William Lee being preferred because the hinge of the latch could not be made as fine as the bearded needle.

Townsend was in the first rank of skilful manufacturers of fancy Leicester hosiery and had a good practical knowledge of the machinery used in his trade. Having patented his needles, he seems not to have succeeded in getting them into very profitable or extensive use, possibly because he fixed the royalty too high. His invention proved to be most useful and profitable in the hands of others, for it gave great impetus to the trade in seamless hose. For various reasons he discontinued his business in Leicester. He emigrated to the USA, where, after some initial setbacks, he began to reap the rewards of his skill.

[br]