-
61 disk winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
дисковая обмотка
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > disk winding
-
62 scoring saw blade
3.5 дисковая пила для надпила (scoring saw blade): Дисковая пила, установленная перед основной дисковой пилой, которая выполняет надпил на нижней пласти обрабатываемой заготовки (рисунок 4) (далее - подрезная пила).
1 - подрезная дисковая пила; 2 - основная дисковая пила; 3 - ограждение пилы ниже стола станка
Рисунок 4 - Пример основной и подрезной дисковых пил
(ограждение дисковой пилы над столом станка не показано)Англо-русский словарь нормативно-технической терминологии > scoring saw blade
-
63 disc type winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disc type winding
-
64 disc winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disc winding
-
65 disk type winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disk type winding
-
66 portable circular saw
36. Дисковая пневматическая (электрическая) ручная пила
D. Handkreissage
E. Portable circular saw
F. Scie circulaire portative
Источник: ГОСТ 16436-70: Машины ручные пневматические и электрические. Термины и определения оригинал документа
Англо-русский словарь нормативно-технической терминологии > portable circular saw
-
67 large reading dial
* * *Англо-русский словарь нефтегазовой промышленности > large reading dial
-
68 disk rolling cutter
Англо-русский словарь нефтегазовой промышленности > disk rolling cutter
-
69 side mill
дисковая фреза, трёхсторонняя дисковая фрезаEnglish-Russian dictionary of mechanical engineering and automation > side mill
-
70 slitting wheel
дисковая пила; дисковая прорезная фрезаEnglish-Russian dictionary of mechanical engineering and automation > slitting wheel
-
71 spade
-
72 multidrive disk memory
English-Russian dictionary of terms that are used in computer games > multidrive disk memory
-
73 buzz saw
-
74 circular saw
-
75 on-disk database
дисковая база данных, дисковая БДБД, обычно крупная и относительно медленная, размещаемая на дисковой памятиAnt:см. тж. databaseАнгло-русский толковый словарь терминов и сокращений по ВТ, Интернету и программированию. > on-disk database
-
76 attrition mill
дисковая дробилка; дисковая мельница -
77 cutout-disk harrow
English-Russian big polytechnic dictionary > cutout-disk harrow
-
78 perepheral saw
-
79 rotary saw
-
80 saw disk
См. также в других словарях:
дисковая фрикционная муфта — дисковая муфта Фрикционная муфта, плоская поверхность трения которой расположена на торце диска. Примечания 1. Дисковая муфта, состоящая из одного подвижного и одного неподвижного дисков, называется «простая дисковая муфта». 2.… … Справочник технического переводчика
Дисковая пила — стальной диск с нанесенными на его окружности зубьями. В циркулярных станках дисковая пила приводится во вращение электродвигателем. Дисковые пилы применяются для разрезания древесины, металла и других материалов. По английски: Circular saw… … Финансовый словарь
Дисковая фотоплёнка — Дисковая плёнка Kodak … Википедия
Дисковая операционная система — операционная система, загружаемая в компьютер с диска. По английски: Disk Operating System Синонимы: ДОС Синонимы английские: DOS См. также: Дисковые операционные системы Операционные системы Финансовый словарь Финам … Финансовый словарь
дисковая катушечная обмотка — Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов [ГОСТ 16110 82] Параллельные тексты EN RU Aluminum or copper foil disk in high voltage… … Справочник технического переводчика
дисковая фреза с разнонаправленными зубьями — Дисковая фреза с зубьями, попеременно направленными в стороны обоих торцов. [http://sl3d.ru/o slovare.html] Тематики машиностроение в целом … Справочник технического переводчика
ДИСКОВАЯ ОПЕРАЦИОННАЯ СИСТЕМА — (ДОС), компьютерная операционная система, разработанная в начале 1980 х гг. корпорацией «Майкрософт» для использования на ранних версиях персональных компьютеров IBM (International Bureau Machines). ДОС до сих пор используют на многих… … Научно-технический энциклопедический словарь
Дисковая пила — (a. circular saw; н. Kreissage; ф. scie circulaire; и. sierra de disco; sierra circular) рабочий режущий инструмент камнерезных машин, распиловочных и окантовочных станков, имеющий форму диска. Используется для вырезания блоков камня из… … Геологическая энциклопедия
ДИСКОВАЯ ОПЕРАЦИОННАЯ СИСТЕМА (ДОС) — (disk operating system, DOS) Операционная система (operating system), предназначенная для использования в компьютерах, которые имеют один или несколько дисководов (disk drives). Бизнес. Толковый словарь. М.: ИНФРА М , Издательство Весь Мир .… … Словарь бизнес-терминов
Дисковая пила — (circular saw): машина, предназначенная для резки различных материалов вращающимся пильным зубчатым диском... Источник: ГОСТ Р МЭК 60745 2 5 2007. Машины ручные электрические. Безопасность и методы испытаний. Часть 2 5. Частные требования к… … Официальная терминология
дисковая МГД-машина — дисковая МГД машина; радиальная МГД машина МГД машина, в которой движение рабочей среды осуществляется в дискообразном канале в основном прямолинейно в радиальном направлении … Политехнический терминологический толковый словарь