-
1 воздействие производства энергии на окружающую среду
воздействие производства энергии на окружающую среду
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
environmental impact of energy
Energy and environmental problems are closely related, since it is nearly impossible to produce, transport, or consume energy without significant environmental impact. The environmental problems directly related to energy production and consumption include air pollution, water pollution, thermal pollution, and solid waste disposal. The emission of air pollutants from fossil fuel combustion is the major cause of urban air pollution. Diverse water pollution problems are associated with energy usage. One major problem is oil spills. In all petroleum-handling operations, there is a finite probability of spilling oil either on the earth or in a body of water. Coal mining can also pollute water. Changes in groundwater flow produced by mining operations often bring otherwise unpolluted waters into contact with certain mineral materials which are leached from the soil and produce an acid mine drainage. Solid waste is also a by-product of some forms of energy usage. Coal mining requires the removal of large quantities of earth as well as coal. In general, environmental problems increase with energy use and this combined with the limited energy resource base is the crux of the energy crisis. An energy impact assessment should compare these costs with the benefits to be derived from energy use. (Source: RAU)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > воздействие производства энергии на окружающую среду
-
2 заброшенная мусорная яма
заброшенная мусорная яма
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
old landfill site
Landfill that has been filled and covered with topsoil and seeded. The most common end use for landfills is open spaces with no active recreation taking place over the completed landfill. The obvious reason for this use is that the completed surface is steeply sloped to provide rapid runoff. Also, no irrigation of the cover grasses should be allowed. It is very unlikely to think that commercial or industrial buildings will be constructed on a completed landfill. If the end use is such that the public will be walking on the site, it is important that all manholes be properly secured, leachate lagoons fenced, and other potential hazards eliminated. (Source: CORBITa)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > заброшенная мусорная яма
-
3 производная единица системы единиц физических величин
производная единица системы единиц физических величин
производная единица
Единица производной физической величины системы единиц, образованная в соответствии с уравнением, связывающим ее с основными единицами или с основными и уже определенными производными.
Примеры
1. 1 м/с - единица скорости, образованная из основных единиц СИ - метра и секунды.
2. 1 Н - единица силы, образованная из основных единиц СИ - килограмма, метра, и секунды.
[РМГ 29-99]EN
derived unit
unit of measurement for a derived quantity
NOTE 1 – Some derived units in the International System of Units (SI) have special names, e.g. hertz for frequency and joule for energy, but others have compound names, e.g. metre per second for speed. Compounds including units with special names are also used, e.g. volt per metre for the electric field strength, and newton metre for torque. See in particular ISO 31 and ISO/IEC 80000.
NOTE 2 – Derived units can also be expressed by using multiples and submultiples. For example, the metre per second, symbol m/s, and the centimetre per second, symbol cm/s, are derived units of speed in the SI. The kilometre per hour, symbol km/h, is a unit of speed outside the SI but accepted for use with the SI, because the unit hour is accepted for use with the SI. The knot, equal to one nautical mile per hour, is a unit of speed outside the SI, that is used by special interest groups.
Source: ISO/IEC GUIDE 99:2007 1.11
[IEV number 112-01-19]FR
unité dérivée, f
unité de mesure d'une grandeur dérivée
NOTE 1 – Certaines unités dérivées dans le SI ont des noms spéciaux, par exemple le hertz pour la fréquence et le joule pour l'énergie, tandis que d'autres ont des noms composés, par exemple le mètre par seconde pour la vitesse. Les unités ayant des noms spéciaux sont aussi utilisées dans des noms composés, par exemple le volt par mètre pour le champ électrique et le newton mètre pour le moment de torsion. Voir en particulier l'ISO 31 et l'ISO/CEI 80000.
NOTE 2 – On peut aussi exprimer les unités dérivées en utilisant des multiples et des sous-multiples. Par exemple, le mètre par seconde, symbole m/s, et le centimètre par seconde, symbole cm/s, sont des unités dérivées de vitesse dans le SI. Le kilomètre par heure, symbole km/h, est une unité de vitesse en dehors du SI mais en usage avec le SI, parce que l'heure est une unité en usage avec le SI. Le nœud, égal à un mille marin par heure, est une unité de vitesse en dehors du SI, qui répond aux besoins spécifiques de certains groupes d’utilisateurs.
Source: ISO/IEC GUIDE 99:2007 1.11
[IEV number 112-01-19]Тематики
- метрология, основные понятия
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > производная единица системы единиц физических величин
-
4 управление землями различного хозяйственного назначения
управление землями различного хозяйственного назначения
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
multiple use management area
1) Coordinated management for the most judicious and harmonious use of the land on a long term basis under the concept of combining two or more uses and/or purposes with attention to sustainability and nonimpairment of the natural resources and land area. 2) Use of land for more than one purpose; e.g. grazing of livestock, watershed and wildlife protection, recreation, and timber production. (Source: UNUN / EPAGLO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > управление землями различного хозяйственного назначения
-
5 группа влияния
группа влияния
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
pressure group
Any politically active group with a common set of values about resource use allocation. Pressure groups seek to influence decisions on resource use allocation in excess of their proportional representation in the planned-for populace by seeking preferential consideration for their resource use choices. (Source: LANDY)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > группа влияния
-
6 энергия ГЭС
энергия ГЭС
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
hydroelectric energy
The free renewable source of energy provided by falling water that drives the turbines. Hydropower is the most important of the regenerable energy sources because of its highest efficiency at the energy conversion. There are two types of hydroelectric power plants: a) run-of-river power plants for the use of affluent water; b) storage power plants (power stations with reservoir) where the influx can be regulated with the help of a reservoir. Mostly greater differences in altitudes are being used, like mountain creeks. Power stations with reservoirs are generally marked by barrages with earth fill dam or concrete dams. Though hydropower generally can be called environmentally acceptable, there exist also some problems: a) change of groundwater level and fill up of the river bed with rubble. b) Risk of dam breaks. c) Great demand for land space for the reservoir. d) Diminution, but partly also increase of value of recreation areas. As the hydropowers of the world are limited, the world energy demand however is rising, finally the share of hydropower will decrease. (Source: PORT / PHC / PZ)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > энергия ГЭС
-
7 аппаратура распределения
аппаратура распределения
Общий термин для коммутационных аппаратов и их комбинаций с относящимися к ним устройствами управления, измерения, защиты и регулирования, а также для узлов, в которых такие аппараты и устройства соединяются с соответствующими фидерами, комплектующим оборудованием, оболочками и опорными конструкциями, предназначенных, в принципе, для использования в системах производства, передачи, распределения и преобразования электрической энергии.
МЭК 60050(441-11-02).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
switchgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures, intended in principle for use in connection with generation, transmission, distribution and conversion of electric energy
[IEV number 441-11-02]FR
appareillage de connexion
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les supports correspondants, destinés en principe à être utilisés dans le domaine de la production, du transport, de la distribution et de la transformation de l'énergie électrique
[IEV number 441-11-02]Тематики
- аппарат, изделие, устройство...
EN
DE
- Schaltanlagen und/oder Schaltgeräte für Energieverteilung
FR
Русско-французский словарь нормативно-технической терминологии > аппаратура распределения
-
8 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
9 израсходованная вода
израсходованная вода
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
water for consumption
Consumptive water use starts with withdrawal, but in this case without any return, e.g. irrigation, steam escaping into the atmosphere, water contained in final products, i.e. it is no longer available directly for subsequent use. (Source: GOOD)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > израсходованная вода
-
10 орган управления
орган управления
Частьсистемыаппарата управления, к которой прилагается извне усилие управления.
МЭК 60050(441-15-22).
Примечание. Орган управления может иметь форму рукоятки, ручки, нажимной кнопки, ролика, плунжера и т. п.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
орган управления
Часть приводного механизма, к которой прикладывается внешняя сила воздействия.
Примечание - Орган управления может иметь форму ручки, кнопки, ролика, поршня и т.д.
[ ГОСТ Р 52726-2007]
орган управления
Часть системы привода, подвергаемая внешнему силовому воздействию.
Примечания
1. Орган управления может иметь форму ручки, рукоятки, нажимной кнопки, ролика, плунжера и т.д.
2. Есть несколько способов приведения в действие, которые не требуют внешнего силового воздействия, а только какого-либо действия.
[ГОСТ ЕН 1070-2003]
орган управления
Часть системы управления, которая предназначена непосредственно для воздействия оператором, например путем нажатия.
[ГОСТ Р ЕН 614-1-2003]
орган управления
Часть системы приведения в действие, которая принимает воздействие человека.
[ ГОСТ Р МЭК 60447-2000]
орган управления
Часть системы приведения в действие, которая воспринимает воздействие человека (ГОСТ Р МЭК 60447).
Примечание
В настоящем стандарте орган управления в виде интерактивного экранного устройства отображения является частью этого устройства, которое представляет функцию органа управления.
[ ГОСТ Р МЭК 60073-2000]
орган управления
Часть механизма прибора управления, на который оказывается вручную внешнее силовое воздействие.
Примечание.
Орган управления может иметь форму ручки, рукоятки, кнопки, ролика, плунжера и т.д.
Некоторые органы управления не требуют воздействия внешней силы, а только какого-либо действия.
[ ГОСТ Р МЭК 60204-1-2007]
органы управления
Ручки, переключатели, потенциометры и другие органы, служащие для включения и регулировки аппаратуры. Термин относится преимущественно к аналоговым приборам.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
орган управления
-
[IEV number 442-04-14]
средства оперирования
-
[Интент]EN
actuator
the part of the actuating system to which an external actuating force is applied
NOTE – The actuator may take the form of a handle, knob, push-button, roller, plunger, etc.
[IEV number 441-15-22]
actuator
part of a device to which an external manual action is to be applied
NOTE 1 The actuator may take the form of a handle, knob, push-button, roller, plunger, etc.
NOTE 2 There are some actuating means that do not require an external actuating force, but only an action.
NOTE 3 See also 3.34.
[IEC 60204-1 -2005]
actuating member
a part which is pulled, pushed, turned or otherwise moved to cause an operation of the switch
[IEV number 442-04-14]FR
organe de commande
partie du mécanisme transmetteur à laquelle un effort extérieur de manoeuvre est appliqué
NOTE – L'organe de commande peut prendre la forme d'une poignée, d'un bouton, d'un bouton-poussoir, d'une roulette, d'un plongeur, etc.
[IEV number 441-15-22]
organe de manoeuvre
partie qui est tirée, poussée, tournée ou manipulée de toute autre façon pour provoquer le fonctionnement de l'interrupteur
[IEV number 442-04-14]
Аппарат должен оставаться механически действующим. Не допускается сваривание контактов, препятствующее операции размыкания при использовании нормальных средств оперирования.
[ГОСТ Р 50030.3-99 (МЭК 60947-3-99) ]
ВДТ следует оперировать как при нормальной эксплуатации. Операции размыкания должны проводиться в следующем порядке:
для первых 1000 циклов — с использованием ручных средств оперирования;...
[ ГОСТ Р 51326. 1-99 ( МЭК 61008-1-96)]Параллельные тексты EN-RU
The operating means (for example, a handle) of the supply disconnecting device shall be easily accessible and located between 0,6 m and 1,9 m above the servicing level.
[IEC 60204-1-2006]Органы управления, например, рукоятки аппаратов отключения питания, должны быть легко доступны и располагаться на высоте от 0,6 до 1,9 м от рабочей площадки.
[Перевод Интент]Where the external operating means is not intended for emergency operations, it is recommended that it be coloured BLACK or GREY.
[IEC 60204-1-2006]Если внешние средства оперирования не предназначены для выполнения действий при возникновении аварийных ситуаций, то рекомендуется, применять такие средства ЧЕРНОГО или СЕРОГО цвета.
[Перевод Интент]1.2.2. Control devices
Control devices must be:
— clearly visible and identifiable and appropriately marked where necessary,
— positioned for safe operation without hesitation or loss of time, and without ambiguity,
— designed so that the movement of the control is consistent with its effect,
— located outside the danger zones, except for certain controls where necessary, such as emergency stop, console for training of robots,
— positioned so that their operation cannot cause additional risk,
— designed or protected so that the desired effect, where a risk is involved, cannot occur without an intentional operation,
— made so as to withstand foreseeable strain; particular attention must be paid to emergency stop devices liable to be subjected to considerable strain.1.2.2. Органы управления
Органы управления должны быть:
- четко видны, хорошо различимы и, где это необходимо, иметь соответствующее обозначение;
- расположены так, чтобы ими можно было пользоваться без возникновения сомнений и потерь времени на выяснение их назначения;
- сконструированы так, чтобы перемещение органа управления согласовывалось с их воздействием;
- расположены вне опасных зон; исключение, где это необходимо, делается для определенных средств управления, таких, как средство экстренной остановки, пульт управления роботом;
- расположены так, чтобы их использование не вызывало дополнительных рисков;
- сконструированы или защищены так, чтобы в случаях, где возможно возникновение рисков, они не могли бы возникнуть без выполнения намеренных действий;
- сделаны так, чтобы выдерживать предполагаемую нагрузку; при этом особое внимание уделяется органам аварийного останова, которые могут подвергаться значительным нагрузкам.Where a control is designed and constructed to perform several different actions, namely where there is no one-to-one correspondence (e.g. keyboards, etc.), the action to be performed must be clearly displayed and subject to confirmation where necessary.
Если орган управления предназначен для выполнения разных действий, например, если в качестве органа управления используется клавиатура или аналогичное устройство, то должна выводиться четкая информация о предстоящем действии, и, если необходимо, должно выполняться подтверждение на выполнение такого действия.
Controls must be so arranged that their layout, travel and resistance to operation are compatible with the action to be performed, taking account of ergonomic principles.
Органы управления должны быть организованы таким образом, чтобы их расположение, перемещение их элементов и усилие, которое оператор затрачивает на их перемещение, соответствовали выполняемым операциям и принципам эргономики.
Constraints due to the necessary or foreseeable use of personal protection equipment (such as footwear, gloves, etc.) must be taken into account.
Необходимо учитывать скованность движений операторов при использовании необходимых или предусмотренных средств индивидуальной защиты (таких, как специальная обувь, перчатки и др.).
Machinery must be fitted with indicators (dials, signals, etc.) as required for safe operation. The operator must be able to read them from the control position.
Для обеспечения безопасной эксплуатации машинное оборудование должно быть оснащено индикаторами (циферблатами, устройствами сигнализации и т. д.). Оператор должен иметь возможность считывать их с места управления.
From the main control position the operator must be able to ensure that there are no exposed persons in the danger zones.
Находясь в главном пункте управления, оператор должен иметь возможность контролировать отсутствие незащищенных лиц.
If this is impossible, the control system must be designed and constructed so that an acoustic and/ or visual warning signal is given whenever the machinery is about to start.
Если это невозможно, то система управления должна быть разработана и изготовлена так, чтобы перед каждым пуском машинного оборудования подавался звуковой и/или световой предупредительный сигнал.
The exposed person must have the time and the means to take rapid action to prevent the machinery starting up.
[DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL]
Незащищенное лицо должно иметь достаточно времени и средств для быстрого предотвращения пуска машинного оборудования.
[Перевод Интент]
Тематики
- автоматизация, основные понятия
- аппарат, изделие, устройство...
- безопасность машин и труда в целом
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
- электробезопасность
- электротехника, основные понятия
Синонимы
EN
- actuating member
- actuator
- command unit
- control
- control device
- controller
- controls
- operating control
- operating means
DE
FR
Русско-французский словарь нормативно-технической терминологии > орган управления
-
11 водная эрозия
водная эрозия
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
water erosion
The breakdown of solid rock into smaller particles and its removal by water. As weathering, erosion is a natural geological process, but more rapid soil erosion results from poor land-use practices, leading to the loss of fertile topsoil and to the silting of dams, lakes, rivers and harbours. There are three classes of erosion by water. a) Splash erosion occurs when raindrops strike bare soil, causing it to splash, as mud, to flow into spaces in the soil and to turn the upper layer of soil into a structureless, compacted mass that dries with a hard, largely impermeable crust. b) Surface flow occurs when soil is removed with surface run-off during heavy rain. c) Channelized flow occurs when a flowing mixture of water and soil cuts a channel, which is then deepened by further scouring. A minor erosion channel is called a rill, a larger channel a gully. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > водная эрозия
-
12 НКУ распределения и управления для строительных площадок (НКУ СП)
НКУ распределения и управления для строительных площадок (НКУ СП)
Комбинация одного или нескольких трансформаторных устройств или коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты и регулирования со всеми внутренними электрическими и механическими соединениями и конструктивными элементами, разработанная и изготовленная для применения на любых строительных площадках — для наружной и внутренней установки.
[ ГОСТ Р 51321. 4-2000 ( МЭК 60439-4-90)]EN
low-voltage switchgear and controlgear assembly for construction sites (ACS)
combination of one or several transforming or switching devices with associated control, measuring, signalling, protective and regulating equipment complete with all their internal electrical and mechanical connections and structural parts, designed and built for use on all construction sites, indoors and outdoors
[IEC 60439-4, ed. 2.0 (2004-06)]FR
ensemble d'appareillage à basse tension utilisé sur les chantiers (EC)
combinaison d'un ou de plusieurs appareils de transformation ou de connexion avec équipements associés de commande, de mesure, de signalisation, de protection et de régulation complètement assemblés avec toutes leurs liaisons internes électriques et mécaniques et leurs éléments de construction (voir 2.4), conçue et construite pour être utilisée sur tous les chantiers, à l'intérieur et à l'extérieur.
[IEC 60439-4, ed. 2.0 (2004-06)]
Рис. ABB
Рис. ABB
Рис. ABBНКУ СП, устанавливаемое на ножках
НКУ СП, закрепляемое на вертикальной поверхности
НКУ СП розеточное
Параллельные тексты EN-RU
Assemblies for construction sites have different dimensions, ranging from the simple socket-outlet units to proper distribution boards in metal enclosure or insulating material.
These assemblies are usually mobile.
The Standard IEC 60439-4 establishes the particular requirements for this type of assemblies, making specific reference to mechanical strength and resistance to corrosion.
[ABB]НКУ для строительных площадок имеют разные размеры и функции - от простых розеточных до распределительных панелей в металлической или пластмассовой оболочке.
Данные НКУ обычно являются переносными.
Стандарт МЭК 60439-4 устанавливает дополнительные требования для НКУ данного типа, особенно по механической прочности и коррозионной стойкости.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
- ACS
- assemblies for construction sites
- low-voltage switchgear and controlgear assembly for construction sites
FR
Русско-французский словарь нормативно-технической терминологии > НКУ распределения и управления для строительных площадок (НКУ СП)
-
13 облучение продуктов питания
облучение продуктов питания
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
food irradiation
The most recent addition to food preservation technologies is the use of ionizing radiation, which has some distinct advantages over conventional methods. With irradiation, foods can be treated after packaging, thus eliminating post-processing contamination. In addition, foods are preserved in a fresh state and can be kept longer without noticeable loss of quality. Food irradiation leaves no residues, and changes in nutritional value due to irradiation are comparable with those produced by other processes. Irradiation is the process of applying high energy to a material, such as food, to sterilize or extend its shelf-life by killing microorganisms, insects and other pests residing on it. Sources of ionizing radiation that have been used include gamma rays, electron beams and X-rays. Gamma rays are produced by radioactive isotopes such as Cobalt-60. Electron beams are produced by linear accelerators, which themselves are powered by electricity. The dose applied to a product is the most important factor of the process. At high doses, food is essentially sterilized, just as occurs in canning. Products so treated can be stored at room temperature almost indefinitely. Controversial and banned in some countries. (Source: IFSE / VCN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > облучение продуктов питания
-
14 планирование ландшафта
планирование ландшафта
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
landscape planning
The aspect of the land use planning process that deals with physical, biological, aesthetic, cultural, and historical values and with the relationships and planning between these values, land uses, and the environment. (Source: UNUN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > планирование ландшафта
-
15 секция шинопровода с ответвлениями троллейного типа
- élément de canalisation préfabriquée avec possibilité de dérivation par chariot collecteur
секция шинопровода с ответвлениями троллейного типа
Секция, предназначенная для использования ответвлений роликового или щеточного типа.
[ ГОСТ Р 51321.2-2009]EN
busbar trunking unit with trolley-type tap-off facilities
busbar trunking unit designed to permit the use of roller- or brush-type tap-off units
[IEC 60439-2, ed. 3.0 (2000-03)]FR
élément de canalisation préfabriquée avec possibilité de dérivation par chariot collecteur
élément de canalisation préfabriquée conçu de manière à permettre l'usage de matériel à contact roulant ou glissant comme éléments de dérivation
[IEC 60439-2, ed. 3.0 (2000-03)]Тематики
- изделие электромонтажное
- электропроводка, электромонтаж
EN
FR
- élément de canalisation préfabriquée avec possibilité de dérivation par chariot collecteur
Русско-французский словарь нормативно-технической терминологии > секция шинопровода с ответвлениями троллейного типа
-
16 бензоспирт
бензоспирт
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
gasohol
A mixture of 80% or 90% petrol with 20% or 10% ethyl alcohol, for use as a fuel in internal combustion engines. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > бензоспирт
-
17 бетонирование подводное с «островка»
- coulage du béton sous l'eau à partir de «l'îlot»
бетонирование подводное с «островка»
Подводное бетонирование с подачей и втрамбованием пластичной бетонной смеси в ранее уложенный и выступающий из воды «островок» с постепенным продвижением его наружного откоса
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
- underwater concreting with the use of artificial «island»
DE
FR
- coulage du béton sous l'eau à partir de «l'îlot»
Русско-французский словарь нормативно-технической терминологии > бетонирование подводное с «островка»
-
18 биологическая утилизация отходов
биологическая утилизация отходов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biological waste treatment
A generic term applied to processes that use microorganisms to decompose organic wastes either into water, carbon dioxide, and simple inorganic substances, such as aldehydes and acids. The purpose of biological waste treatment is to control either the environment for microorganisms so that their growth and activity are enhanced, and to provide a means for maintaining high concentrations of the microorganisms in contact with the wastes.
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > биологическая утилизация отходов
-
19 вакуумный автоматический выключатель
вакуумный автоматический выключатель
Выключатель, контакты которого размыкаются и замыкаются в сильно разряженной атмосфере внутри оболочки.
(МЭС 441-14-29)
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]EN
vacuum circuit-breaker
circuit-breaker in which the contacts open and close within a highly evacuated envelope.
[IEC 60077-4, ed. 1.0 (2003-02)]FR
disjoncteur à vide
disjoncteur dont les contacts s'ouvrent et se ferment dans une enceinte où règne un vide poussé.
[IEC 60077-4, ed. 1.0 (2003-02)]Параллельные тексты EN-RU
Susol VCB series are premium-type products featuring main structure with high reliability application and a variety of accessories and ability to maximize to be suitable for use as the main circuit breaker to protect key installations in the places such as device industry, power plants, high-rise buildings, large ships.
[LS Industrial Systems]Вакуумные автоматические выключатели Susol являются устройствами премиум-класса, характеризующимися надежной конструкцией, наличием разнообразных дополнительных принадлежностей и возможностью применения в качестве вводного автоматического выключателя, обеспечивающего защиту ключевых электроустановок промышленных предприятий, электростанций, высотных зданий и крупных судов.
[Перевод Интент]
Рис. LS Industrial Systems
Вакуумный автоматический выключатель Susol1
Push ON Button
Кнопка ВКЛ.
2
Push OFF Button
Кнопка ОТКЛ.
3
Charge/Discharge Indicator
Индикатор состояния пружины ВЗВЕДЕНА/РАЗРЯЖЕНА
4
ON/OFF Indicator
Индикатор коммутационного положения автоматического выключателя ВКЛ/ОТКЛ.
5
Manual Charging Handle
Рукоятка ручного взвода пружины
6
Key Lock
Замок
7
Operation Counter
Счетчик коммутационных циклов
8
TEST/SERVICE Position Indicator
Указатель положения автоматического выключателя в корзине ИСПЫТАТЕЛЬНОЕ/ПРИСОЕДИНЕННОЕ
Тематики
Классификация
>>>Обобщающие термины
EN
FR
Русско-французский словарь нормативно-технической терминологии > вакуумный автоматический выключатель
-
20 включающая способность (коммутационного аппарата)
включающая способность (коммутационного аппарата)
Значение ожидаемого тока включения, который способен включать коммутационный аппарат при установленном напряжении в предписанных условиях эксплуатации и поведения.
Примечание
Напряжение устанавливается и условия предписываются в стандарте на соответствующий аппарат.
МЭК 60050(441-17-09)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
включающая способность коммутационного аппарата
Коммутационная способность коммутационного аппарата при включении цепи.
[ ГОСТ 17703-72]EN
making capacity (of a switching device or a fuse)
a value of prospective making current that a switching device is capable of making at a stated voltage under prescribed conditions of use and behaviour
NOTE – The voltage to be stated and the conditions to be prescribed are dealt with in the relevant specifications.
[IEV number 441-17-09]
[IEV number 442-01-48]FR
pouvoir de fermeture (d'un appareil de connexion)
une valeur du courant présumé établi qu'un appareil de connexion est capable d'établir sous une tension donnée et dans des conditions prescrites d'emploi et de comportement
NOTE – La tension à fixer et les conditions à prescrire sont précisées dans les spécifications individuelles
[IEV number 441-17-09]
[IEV number 442-01-48]
Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- предохранитель
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > включающая способность (коммутационного аппарата)
См. также в других словарях:
use — n 1 Use, service, advantage, profit, account, avail can all mean a useful or valuable end, result, or purpose. Use stresses either employment for some purpose or end of practical value {turn every scrap of material to use} or the practical value… … New Dictionary of Synonyms
Use case — A use case is a description of a system’s behaviour as it responds to a request that originates from outside of that system.The use case technique is used in software and systems engineering to capture the functional requirements of a system. Use … Wikipedia
use — 1 / yüs/ n 1 a: an arrangement in which property is granted to another with the trust and confidence that the grantor or another is entitled to the beneficial enjoyment of it see also trust; statute of uses in the important laws section ◇ Uses… … Law dictionary
Use of Free and Open Source Software (FOSS) in the U.S. Department of Defense — is a 2003 report by The MITRE Corporation that documented widespread use of and reliance on free software (termed FOSS ) within the United States Department of Defense (DoD). The report helped end a debate about whether FOSS should be banned from … Wikipedia
Use of Beads at Prayers — Use of Beads at Prayers † Catholic Encyclopedia ► Use of Beads at Prayers Beads variously strung together, according to the kind, order, and number of prayers in certain forms of devotion, are in common use among Catholics as an… … Catholic encyclopedia
Use case model — is a model that describes a system’s functional requirements in terms of use cases. Consists of all the actors of the system and all the various use cases by which the actor interact with the system, thereby describing the total functional… … Wikipedia
Use of webcams — at work and home has become a world wide web cultural revolution or change in how we communicate with each other. It can be broken down into positve, negative, freedom of expression or speech and what the future of webcam internet technology may… … Wikipedia
Use of York — Use of York † Catholic Encyclopedia ► Use of York It was a received principle in medieval canon law that while as regards judicial matters, as regards the sacraments, and also the more solemn fasts, the custom of the Roman Church was… … Catholic encyclopedia
Use of Weapons — … Wikipedia
Use (law) — Use, as a term in real property law of common law countries, amounts to a recognition of the duty of a person, to whom property has been conveyed for certain purposes, to carry out those purposes.Uses were equitable or beneficial interests in… … Wikipedia
Use — Use, v. t. [imp. & p. p. {Used}; p. pr. & vb. n. {Using}.] [OE. usen, F. user to use, use up, wear out, LL. usare to use, from L. uti, p. p. usus, to use, OL. oeti, oesus; of uncertain origin. Cf. {Utility}.] [1913 Webster] 1. To make use of; to… … The Collaborative International Dictionary of English