-
1 воздействующая величина электрического реле
воздействующая величина электрического реле
Электрическая величина, которая одна или в сочетании с другими электрическими величинами должна быть приложена к электрическому реле в заданных условиях для достижения ожидаемого функционирования
[ ГОСТ 16022-83]EN
energizing quantity
an electrical quantity (either current or voltage) which alone, or in combination with other such quantities, applied to a relay under specified conditions enables it to fulfil its purpose
[IEV number 446-12-01]
energizing quantity (for elementary relays)electrical quantity which, when applied to the input circuit of an elementary relay under specified conditions, enables it to fulfill its purpose
NOTE – For elementary relays the energizing quantity is usually a voltage. Therefore, the input voltage as energizing quantity is used in the definitions given below. Where a relay is energized by a given current instead, the respective terms and definitions apply with "current" used instead of "voltage".
[IEV number 444-03-01]FR
grandeur d'alimentation
grandeur électrique, courant ou tension, qui, seule ou en combinaison avec d'autres grandeurs électriques, courant ou tension, doit être appliquée dans des conditions spécifiées à un relais pour en obtenir le comportement attendu
[IEV number 446-12-01]
grandeur d'alimentation (pour les relais élémentaires), f
grandeur électrique qui, appliquée au circuit d'entrée d'un relais élémentaire dans des conditions spécifiées, lui permet d'accomplir sa fonction
NOTE – Pour les relais élémentaires, la grandeur d'alimentation est en général une tension. En conséquence, on utilise la tension d'entrée comme grandeur d'alimentation dans les définitions données ci-dessous. Lorsqu'un relais est alimenté par un courant, les termes et définitions respectifs sont à utiliser avec le terme "courant" au lieu du terme "tension".
[IEV number 444-03-01]Тематики
Классификация
>>>EN
DE
FR
49. Воздействующая величина электрического реле
D. Eingangsgrösse
Е. Energizing quantity
F. Grandeur d’alimentation
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > воздействующая величина электрического реле
-
2 яд
яд
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
poison
A substance which, when ingested, inhaled, or absorbed, or when applied to, injected into, or developed within the body, in relatively small amounts, may cause injury, harm, or destruction to organs, tissue, or life. (Source: CONFER)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > яд
-
3 компост из сточного ила и отходов
компост из сточного ила и отходов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
refuse-sludge compost
Compost derived by the biodegradation of the organic constituents of solid wastes and wastewater sludges. The major public health issues associated with composting using solid wastes mixed with sewage sludge are pathogens, heavy metal, and odors. The heat generated during composting, as a result of the activities of thermophilic organisms, is capable of killing bacteria, viruses, protozoa and helminths present in sewage sludge. The metallic elements in sludge of greatest concern to human health are cadmium, lead, arsenic, selenium, and mercury. Only cadmium is normally found in sewage sludge at levels which, when applied to soils, can be absorbed by plants, and accumulate in edible parts, thereby entering the food chain. (Source: CORBIT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > компост из сточного ила и отходов
-
4 время устойчивого замыкания (размыкания) контакта электрического реле
время устойчивого замыкания (размыкания) контакта электрического реле
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
[ ГОСТ 16022-83]EN
time to stable closed condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is closed and fulfils specified requirements
[IEV number 446-17-24]
time to stable open condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is open and fulfils specified requirements
[IEV number 446-17-25]FR
temps de fermeture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est fermé et répond aux prescriptions spécifiées
[IEV number 446-17-24]
temps d'ouverture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est ouvert et répond aux prescriptions spécifiées
[IEV number 446-17-25]
Тематики
EN
DE
FR
136. Время устойчивого замыкания (размыкания) контакта электрического реле
D. Ansprech-Rückfallzeit
Е. Time to stable closed (open) condition
F. Temps de fermeture (d’ouverture) stable
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > время устойчивого замыкания (размыкания) контакта электрического реле
-
5 автоматический выключатель
автоматический выключатель
Механический коммутационный аппарат1), способный включать, проводить и отключать токи при нормальном состоянии электрической цепи, а также включать, проводить в течение заданного времени и автоматически отключать токи в указанном аномальном состоянии электрической цепи, например, при коротком замыкании.
(МЭС 441-14-20)
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]
автоматический выключатель
-
[IEV number 442-05-01]EN
circuit breaker
a mechanical switching device, capable of making, carrying and breaking currents under normal circuit conditions and also making, carrying for a specified time and breaking currents under specified abnormal circuit conditions such as those of short circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
circuit breaker
A device designed to open and close a circuit by nonautomatic means and to open the circuit automatically on a predetermined overcurrent without damage to itself when properly applied within its rating.
NOTE The automatic opening means can be integral, direct acting with the circuit breaker, or remote from the circuit breaker.
Adjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker can be set to trip at various values of current, time, or both within a predetermined range. Instantaneous-trip (as applied to circuit breakers). A qualifying term indicating that no delay is purposely introduced in the tripping action of the circuit breaker.
Inverse-time (as applied to circuit breakers). A qualifying term indicating a delay is purposely introduced in the tripping action of the circuit breaker, which delay decreases as the magnitude of the current increases.
Nonadjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker does not have any adjustment to alter the value of current at which it will trip or the time required for its operation.
Setting (of a circuit breaker). The value of current, time, or both at which an adjustable circuit breaker is set to trip.
[National Electrical Cod]FR
disjoncteur
1) Должно быть контактный коммутационный аппарат
appareil mécanique de connexion capable d’établir, de supporter et d’interrompre des courants dans les conditions normales du circuit, ainsi que d’établir, de supporter pendant une durée spécifiée et d’in- terrompre des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
[Интент]КЛАССИФИКАЦИЯ
- По роду тока
- По напряжению
- По числу полюсов
- По виду корпуса
- По месту установки
- По изолирующей среде
- По установленным расцепителям
- По дополнительным защитам
- По назначению
- По категории применения
- По виду привода взвода пружины
- По выполняемой функции
-
По влиянию монтажного положения
Автоматические выключатели ABB Модульные автоматические выключатели
1. НЕКОТОРЫЕ СВЕДЕНИЯ ОБ АВТОМАТИЧЕСКИХ ВЫКЛЮЧАТЕЛЯХ Автоматический выключатель — это электрический аппарат, который автоматически отключает (и тем самым защищает) электрическую цепь при возникновении в ней аномального режима. Режим становится аномальным, когда в цепи начинает недопустимо изменяться (т. е. увеличиваться или уменьшаться относительно номинального значения) ток или напряжение.
Другими словами (более "инженерно") можно сказать, что автоматический выключатель защищает от токов короткого замыкания и токов перегрузки отходящую от него питающую линию, например, кабель и приемник(и) электрической энергии (осветительную сеть, розетки, электродвигатель и т. п.).
Как правило, автоматический выключатель может применятся также для нечастого (несколько раз в сутки) включения и отключения защищаемых электроприемников (защищаемой нагрузки).
[Интент]Выключатель предназначен для проведения тока в нормальном режиме и отключения тока при коротких замыканиях, перегрузках, недопустимых снижениях напряжения, а также до 30 оперативных включений и отключений электрических цепей в сутки и рассчитан для эксплуатации в электроустановках с номинальным рабочим напряжением до 660 В переменного тока частоты 50 и 60 Гц и до 440 В постоянного тока.
[Типовая фраза из российской технической документации] 2. ПРИНЦИП ДЕЙСТВИЯ Для защиты цепи от короткого замыкания применяется автоматический выключатель с электромагнитным расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Автоматический выключатель устроен таким образом, что сначала необходимо взвести пружину и только после этого его можно включить. У многих автоматических выключателей для взвода пружины необходимо перевести ручку вниз. После этого ручку переводят вверх. При этом замыкаются главные контакты.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Электромагнитный расцепитель;
5 - Сердечник
6 - Катушка
7 - Контактные зажимы автоматического выключателя
На рисунке показан один полюс автоматического выключателя во включенном положении: пружина 1 взведена, а главный контакт 2 замкнут.
Как только в защищаемой цепи возникнет короткое замыкание, ток, протекающий через соответствующий полюс автоматического выключателя, многократно возрастет. В катушке 6 сразу же возникнет сильное магнитное поле. Сердечник 5 втянется в катушку и освободит удерживающее устройство. Под действием пружины 1 главный контакт 2 разомкнется, в результате чего автоматический выключатель отключит и тем самым защитит цепь, в которой возникло короткое замыкание. Такое срабатывание автоматического выключателя происходит практически мгновенно (за сотые доли секунды).
Для защиты цепи от тока перегрузки применяют автоматические выключатели с тепловым расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Принцип действия такой же как и в первом случае, с той лишь разницей, что удерживающее устройство 3 освобождается под действием биметаллической пластины 5, которая изгибается от тепла, выделяемого нагревательным элементом 6. Количество тепла определяется током, протекающим через защищаемую цепь.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Тепловой расцепитель
5 - Биметаллическая пластина
6 - Нагревательный элемент
7 - Контактные зажимы автоматического выключателя
[Интент]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Обобщающие термины
Действия
- включение автоматического выключателя
- оперирование автоматического выключателя
- отключение автоматического выключателя
- срабатывание автоматического выключателя
EN
- auto-cutout
- automatic circuit breaker
- automatic cutout
- automatic switch
- breaker
- CB
- circuit breaker
- circuit-breaker
- cutout
DE
FR
Смотри также
Русско-немецкий словарь нормативно-технической терминологии > автоматический выключатель
6 потери холостого хода
потери холостого хода
Активная мощность, потребляемая трансформатором при номинальном напряжении (или напряжении ответвления) и номинальной частоте на выводах одной из обмоток при разомкнутых остальных обмотках
(МЭС 421-06-01).
Примечание — Значения этих параметров должны быть отнесены к основному ответвлению, если в НД не указано другое ответвление.
[ ГОСТ 30830-2002]
потери холостого хода
потери х. х.
Потери, возникающие в трансформаторе в режиме холостого хода при номинальном напряжении и номинальной частоте
[ ГОСТ 16110-82]EN
no-load loss
the active power absorbed when a given voltage at rated frequency is applied to the terminals of one of the windings, the other winding(s) being open-circuited
NOTE – Normally the applied voltage is the rated voltage and the energized winding, if fitted with tappings, is connected on its principal tapping
[IEV number 421-06-01]FR
pertes à vide
puissance active absorbée quand une tension donnée à la fréquence assignée est appliquée aux bornes de l'un des enroulements, l'autre (ou les autres) enroulement(s) étant à circuit ouvert
NOTE – Normalement, la tension appliquée est la tension assignée et l'enroulement d'excitation, s'il est muni de prises, est connecté sur sa prise principale.
[IEV number 421-06-01]Тематики
Классификация
>>>Синонимы
- потери х. х.
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > потери холостого хода
7 ток холостого хода
ток холостого хода
Ток, протекающий через линейный вывод обмотки, к которой приложено номинальное напряжение (или напряжение ответвления) номинальной частоты, при разомкнутых остальных обмотках.
Примечания
1 Для трехфазного трансформатора током холостого хода считают среднеарифметическое значение токов холостого хода трех фаз.
2 Ток холостого хода одной обмотки обычно выражают в процентах номинального тока этой обмотки. Для многообмоточных трансформаторов этот процент относят к обмотке с наибольшей номинальной мощностью
(МЭС 421-06-02)
[ ГОСТ 30830-2002]EN
no-load current
the current flowing through a line terminal of a winding when a given voltage is applied at rated frequency, the other winding(s) being open-circuited
NOTE 1 – Normally the applied voltage is the rated voltage and the energized winding, if fitted with tappings, is connected on its principal tapping.
NOTE 2 – The no-load current of a winding is often expressed as a percentage of the rated current of the same winding
[IEV number 421-06-02]FR
courant à vide
courant arrivant à une borne de ligne d'un enroulement quand une tension donnée à la fréquence assignée est appliquée à cet enroulement, l'autre (ou les autres) enroulement(s) étant à circuit ouvert
NOTE 1 – Normalement, la tension appliquée est la tension assignée et l'enroulement d'excitation, s'il est muni de prises, est connecté sur sa prise principale.
NOTE 2 – Le courant à vide d'un enroulement est souvent exprimé en pourcentage du courant assigné de cet enroulement.
[IEV number 421-06-02]Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > ток холостого хода
8 время срабатывания электрического реле
время срабатывания электрического реле
Время от момента, когда входная воздействующая или характеристическая величина электрического реле, находящегося в начальном или исходном состоянии, принимает в заданных условиях определенное значение до момента, когда реле завершает срабатывание
[ ГОСТ 16022-83]EN
operate time
for a relay which is in the release condition (initial condition) the time interval between the instant a specified value of the input energizing quantity (characteristic quantity) is applied under specified condition and the instant when the relay switches
NOTE – This term is used only when the relay has output circuits of the same type and no precision is required according to contact time difference.
[IEV number 446-17-09]FR
temps de fonctionnement
temps d'action (terme déconseillé, utilisé pour les relais de tout ou rien)
pour un relais qui est dans l'état de repos ou dans un état initial, temps écoulé entre l'instant où la grandeur d'alimentation d'entrée ou la grandeur caractéristique prend, dans des conditions spécifiées, une valeur définie et l'instant où le relais commute
NOTE – Ce terme n'est utilisé que lorsque le relais ne comporte que des circuits de sortie de même nature et qu'aucune précision n'est nécessaire quant à la dispersion des temps de contact.
[IEV number 446-17-09]Тематики
EN
DE
FR
122. Время срабатывания электрического реле
D. Betätigungszeit
E. Operate time
F. Temps de fonctionnement;
Temps d’action (pour relais de tout ou rien)
Время от момента, когда входная воздействующая или характеристическая величина электрического реле, находящегося в начальном или исходном состоянии, принимает в заданных условиях определенное значение до момента, когда реле завершает срабатывание
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > время срабатывания электрического реле
9 гигроскопичная лента
- Quellband, n
гигроскопичная лента
водонабухающая лента
лента, применяемая под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-16]EN
water blocking tape
swelling tape
tape applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-16]FR
ruban d'étanchéité
ruban gonflant
ruban appliqué sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-16]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellband, n
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичная лента
10 гигроскопичная пудра
- Quellpulver, n
гигроскопичная пудра
водонабухающая пудра
порошковый наполнитель, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-14]EN
water blocking powder
swelling powder
powder applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-14]FR
poudre d'étanchéité
poudre gonflante
poudre appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-14]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellpulver, n
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичная пудра
11 гигроскопичный клей
- Quellmasse, f
гигроскопичный клей
водонабухающий клей
клей, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-17]EN
water blocking glue
swelling glue
glue applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-17]FR
matière d'étanchéité
matière appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-17]
Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellmasse, f
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичный клей
12 внешний запуск
внешний запуск
-
[IEV number 314-06-15]EN
external triggering
triggering obtained when the signal which controls the time base is applied externally
[IEV number 314-06-15]FR
déclenchement externe
déclenchement obtenu quand le signal auquel est asservie la base de temps est appliqué en externe
[IEV number 314-06-15]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > внешний запуск
13 внешняя синхронизация
внешняя синхронизация
Средства синхронизации оборудования от одного источника.
[ http://www.vidimost.com/glossary.html]
внешняя синхронизация
-
[IEV number 314-06-16]EN
external synchronization
synchronization obtained when the signal which controls the time base is applied externally
[IEV number 314-06-16]FR
synchronisation externe
synchronisation obtenue quand le signal auquel est asservie la base de temps est appliqué en externe
[IEV number 314-06-16]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > внешняя синхронизация
14 время замыкания замыкающего контакта электрического реле
время замыкания замыкающего контакта электрического реле
Время от момента, когда входная воздействующая величина электрического реле, находящегося в начальном состоянии, принимает в заданных условиях определенное значение, до момента, когда замкнется в первый раз замыкающий контакт
[ ГОСТ 16022-83]EN
closing time of a make contact
for a relay which is in the release condition, the time interval between the instant a specified value of the input energizing quantity is applied under specified conditions and the instant when the make contact first closes
[IEV number 446-17-03]FR
temps d'établissement d'un contact de travail
pour un relais qui est dans un état de repos, temps écoulé entre l'instant où la grandeur d'alimentation d'entrée prend, dans des conditions spécifiées, une valeur définie et l'instant où s'établit pour la première fois le contact de travail
[IEV number 446-17-03]Тематики
EN
DE
FR
119. Время замыкания замыкающего контакта электрического реле
D. Ansprechzeit eines Schliessers
E. Closing time of a make contact
F. Temps d’etablissement d’un contact de travail
Время от момента, когда входная воздействующая величина электрического реле, находящегося в начальном состоянии, принимает в заданных условиях определенное значение, до момента, когда замкнется в первый раз замыкающий контакт
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > время замыкания замыкающего контакта электрического реле
15 входная возбуждающая величина
входная возбуждающая величина
-
[IEV number 442-05-58]EN
energizing input-quantity
energizing quantity by which the residual current device is activated when it is applied under specified conditions
NOTE – These conditions can involve, e.g., the energizing of certain auxiliary elements.
[IEV number 442-05-58]FR
grandeur d'alimentation d'entrée
grandeur d'alimentation par laquelle le dispositif de coupure différentiel est mis en action, lorsqu'elle est appliquée dans des conditions spécifiées
NOTE – Ces conditions peuvent impliquer, par exemple, l'alimentation de certains organes auxiliaires.
[IEV number 442-05-58]Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > входная возбуждающая величина
16 входная воздействующая величина логического электрического реле
входная воздействующая величина логического электрического реле
Воздействующая величина, на которую электрическое реле предназначено реагировать, если она приложена в заданных условиях
[ ГОСТ 16022-83]EN
input energizing quantity
for an all-or-nothing relay: that energizing quantity to which the relay is designed to respond when the quantity is applied under specified conditions
[IEV number 446-12-02]FR
grandeur d'alimentation d'entrée
pour un relais de tout ou rien: grandeur d'alimentation à laquelle, par conception, le relais doit obéir lorsqu'elle est appliquée dans des conditions spécifiées
[IEV number 446-12-02]Тематики
Классификация
>>>EN
DE
50. Входная воздействующая величина логического электрического реле
D. Erregungsgrösse
Е. Input energizing quantity
F. Grandeur d’alimentation d’entrée
Воздействующая величина, на которую электрическое реле предназначено реагировать, если она приложена в заданных условиях
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > входная воздействующая величина логического электрического реле
17 коэффициент подавления общего вида
коэффициент подавления общего вида
-
[IEV number 312-06-21]EN
common mode rejection ratio
CMRR (abbreviation)
ratio of the voltage applied between a specified reference point and the input terminals, when connected together by a specified circuit, to the voltage required between the input terminals to produce the same value of the output
NOTE 1 – The common mode rejection ratio is usually expressed in decibels and can depend on the frequency, the waveform and the method of measurement.
NOTE 2 – Common mode rejection ratio can also apply to quantities other than voltage.
[IEV number 312-06-21]FR
rapport de réjection de mode commun
rapport de la tension appliquée entre un point de référence spécifié et les deux bornes d'entrée connectées l'une à l'autre par un circuit spécifié, à la tension nécessaire entre les bornes d'entrée pour produire la même valeur de sortie
NOTE 1 – Le facteur de réjection de mode commun est généralement exprimé en décibels et peut dépendre de la fréquence, de la forme d’onde et de la méthode de mesure.
NOTE 2 – Le rapport de réjection de mode commun peut aussi s'appliquer à des grandeurs autres que les tensions.
[IEV number 312-06-21]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент подавления общего вида
18 обрывной соединитель
- Steckverbinder mit Notzugentriegelung, m
обрывной соединитель
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]EN
break-away connector
connector designed to separate when a specified force is applied to the cable or to the housing, without damage to the cable or the connector
[IEV number 581-26-20]FR
connecteur à désaccouplement calibré
connecteur conçu pour être désaccouplé sous I’action d’une force spécifiée appliquée au câble ou au boîtier, sans dommage pour le câble ou le connecteur
[IEV number 581-26-20]Тематики
Классификация
>>>EN
DE
- Steckverbinder mit Notzugentriegelung, m
FR
Смотри также
Русско-немецкий словарь нормативно-технической терминологии > обрывной соединитель
19 реле переключения со звезды на треугольник
- Stern-Dreieck-Relais, n
реле переключения со звезды на треугольник
-
[Интент]EN
star-delta relay
time relay including two delayed outputs switching one after the other, for starting of motors in the star mode and subsequent change to the delta mode (see Figure 6)
NOTE – The star and delta connections are defined in IEV 141-02-06 and IEV 141-02-09 respectively.
[IEV ref 445-01-09]FR
relais temporisé à couplage étoile-triangle, m
Параллельные тексты EN-RU
relais temporisé comportant deux sorties temporisées commutant l'une après l'autre conçu pour assurer le démarrage de moteurs dans un couplage en étoile, puis le passage dans un couplage en triangle (voir Figure 6)
NOTE – Les couplages en étoile et en triangle sont définis en IEV 141-02-06 et IEV 141-02-09 respectivement.
[IEV ref 445-01-09]Star-delta relay
When energy applied to device, star relay is energized until the end of the adjustable tλ, time.
At the end of the adjusted delay time tλ-Δ, delta relay is energized until the device is powered off.
[Klemsan]Реле переключения со звезды на треугольник
При подаче напряжения на реле переключения со звезды на треугольник включается реле включения по схеме "звезда" и остается включенным до окончания заданной задержки tλ.
По окончании задержки времени tλ-Δ включается реле включения по схеме "треугольник" и остается включенным до прекращения подачи напряжения на реле переключения со звезды на треугольник.
[Перевод Интент]
Тематики
EN
DE
- Stern-Dreieck-Relais, n
FR
- relais temporisé à couplage étoile-triangle, m
Русско-немецкий словарь нормативно-технической терминологии > реле переключения со звезды на треугольник
20 реле суммарной задержки срабатывания
- additives Zeitrelais, n
реле суммарной задержки срабатывания
-
[Интент]EN
summation time relay
time relay in which the output switches when the setting time has elapsed by summation of the time periods during which the control signal has been applied (see Figure 7)
[IEV ref 445-01-10]FR
relais temporisé à addition de temps, m
relais temporisé dans lequel la sortie commute lorsque la temporisation réglée est écoulée après addition des durées pendant lesquelles le signal de commande a été appliqué (voir Figure 7)
[IEV ref 445-01-10]Тематики
EN
DE
- additives Zeitrelais, n
FR
- relais temporisé à addition de temps, m
Русско-немецкий словарь нормативно-технической терминологии > реле суммарной задержки срабатывания
Страницы- 1
- 2
См. также в других словарях:
applied logic — Introduction the study of the practical art of right reasoning. The formalism (formal logic) and theoretical results of pure logic can be clothed with meanings derived from a variety of sources within philosophy as well as from other… … Universalium
Applied Scholastics — Infobox Organization size = caption = name = Applied Scholastics formation = 1972 type = Religious status = Non profit purpose = headquarters = Florida, USA leader title = Chairman of Religious Technology Center leader name = David Miscavige num… … Wikipedia
Applied behavior analysis — (ABA) is the science of applying experimentally derived principles of behavior to improve socially significant behavior. ABA takes what we know about behavior and uses it to bring about positive change (Applied). Behaviors are defined in… … Wikipedia
Applied Biosystems — Applied Biosystems, Inc. (formerly nasdaq2|ABIO) is the original name of a pioneer biotechnology company founded in 1981 in Foster City, California, in the San Francisco Bay Area. [http://marketing.appliedbiosystems.com/mk/get/25YRSEMS HERRITAGE… … Wikipedia
Applied linguistics — is an interdisciplinary field of study that identifies, investigates, and offers solutions to language related real life problems. Some of the academic fields related to applied linguistics are education, linguistics, psychology, anthropology,… … Wikipedia
Applied mechanics — is a branch of the physical sciences and the practical application of mechanics. Applied mechanics examines the response of bodies (solids and fluids) or systems of bodies to external forces . Some examples of mechanical systems include the flow… … Wikipedia
Applied aesthetics — is the application of the branch of philosophy of aesthetics to cultural constructs.Film, television, and videoFilm combines many diverse disciplines, each of which may have their own rules of aesthetics. The aesthetics of cinematography are… … Wikipedia
Applied ethics — is, in the words of Brenda Almond, co founder of the Society for Applied Philosophy, the philosophical examination, from a moral standpoint, of particular issues in private and public life that are matters of moral judgment . It is thus a term… … Wikipedia
Applied Sustainability — is the application of science and innovation to meet human needs while indefinitely preserving the life support systems of the planet.Note that this is a significant difference from the standard definition of sustainability that normally is… … Wikipedia
Applied academics — is an approach to learning and teaching that focuses on how (communications, mathematics, science, and basic literacy) can apply to the real world.cite web url=http://www.hocking.edu/ aaffairs/GLOSSARY.HTML title=Glossary publisher=Hocking… … Wikipedia
Applied Engineering — Applied Engineering, headquartered in Carrollton, TX, was a leading third party hardware vendor for the Apple II series of computers from the early 1980s until the mid 1990s.HistoryAs Apple Computer, Inc., began to withdraw support for the Apple… … Wikipedia
Перевод: с русского на немецкий
с немецкого на русский- С немецкого на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский