-
1 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
-
2 коэффициент замыкания на землю
коэффициент замыкания на землю
Отношение наибольшего фазного напряжения в месте металлического замыкания на землю к напряжению в той же точке при отсутствии замыкания.
[ ГОСТ 24291-90]
коэффициент замыкания на землю
Для данного места трехфазной системы заданной конфигурации отношение максимального значения фазного напряжения промышленной частоты на исправном линейном проводнике во время замыкания на землю одного или нескольких линейных проводников в какой-либо точке системы к значению напряжения промышленной частоты в данном месте при отсутствии какого-либо замыкания на землю.
[ ГОСТ Р МЭК 60050-195-2005]
коэффициент замыкания на землю
Отношение напряжения на неповрежденной фазе в рассматриваемой точке трехфазной электрической сети (обычно в точке установки электрооборудования) при замыкании на землю одной или двух других фаз к фазному напряжению рабочей частоты, которое установилось бы в данной точке при устранении замыкания.
Примечание. При определении коэффициента замыкания на землю место замыкания и состояние схемы электрической сети выбираются такими, которые дают наибольшее значение коэффициента
[ ГОСТ 1516.1-76]
коэффициент замыкания на землю
Коэффициент, определяющий отношение влияния на одну или более фаз в любой точке сети во время замыкания на землю другой исправной фазы при наивысшем значении ее напряжения в заданном месте при заданном местоположении трехфазной сети и для заданной конфигурации соответственно в отсутствие любого подобного замыкания. [IEV 604-03-06]
[ ГОСТ Р МЭК 60044-7-2010]EN
earth fault factor
at a given location of a three-phase system, and for a given system configuration, ratio of the highest root-mean-square value of line-to-earth power frequency voltage on a healthy line conductor during an earth fault affecting one or more line conductors at any point on the system, to the root-mean-square value of line-to-earth power frequency voltage which would be obtained at the given location in the absence of any such earth fault
Source: 604-03-06 MOD
[IEV number 195-05-14]FR
facteur de court-circuit à la terre
en un emplacement donné d'un réseau triphasé, et pour un schéma d'exploitation donné de ce réseau, rapport entre d'une part la tension efficace la plus élevée, à la fréquence du réseau, entre un conducteur de ligne saine et la terre pendant un défaut à la terre affectant un ou plusieurs conducteurs de ligne en un point quelconque du réseau, et d'autre part la valeur efficace de la tension phase-terre à la fréquence du réseau qui serait obtenue à l'emplacement considéré en l'absence d'un tel défaut à la terre
Source: 604-03-06 MOD
[IEV number 195-05-14]Тематики
EN
DE
FR
82 коэффициент замыкания на землю
Отношение наибольшего фазного напряжения в месте металлического замыкания на землю к напряжению в той же точке при отсутствии замыкания
604-03-06*
de Erdfehlerfactor
en earth fault factor
fr facteur de défaut à la terre
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > коэффициент замыкания на землю
-
3 минимальный расцепитель напряжения
минимальный расцепитель напряжения
Расцепитель, автоматически срабатывающий, когда подаваемое напряжение опускается ниже заданного уровня.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]
минимальное реле или минимальной расцепитель напряжения
Реле или расцепитель, допускающие размыкание или замыкание контактного коммутационного аппарата с выдержкой времени или без нее, когда напряжение на выводах этого реле или расцепителя падает ниже заданной величины
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
under-voltage release
a shunt release which permits a mechanical switching device to open or close, with or without time-delay, when the voltage across the terminals of the release falls below a predetermined value.
[IEC 62271-100, ed. 2.0 (2008-04)
undervoltage release
release which causes a CBE to open, with or without delay, when the voltage across the terminals of the release falls below a predetermined value
[IEC 60934, ed. 3.0 (2000-10)]FR
déclencheur à minimum de tension
déclencheur shunt qui permet l’ouverture ou la fermeture, avec ou sans retard, d’un appareil mécanique de connexion lorsque la tension aux bornes du déclencheur tombe au-dessous d’une valeur prédéterminée.
[IEC 62271-100, ed. 2.0 (2008-04)]
déclencheur à manque de tension
déclencheur qui provoque l'ouverture du DPE avec ou sans retard, lorsque la tension aux bornes du déclencheur tombe au-dessous d'une valeur prédéterminée
[IEC 60934, ed. 3.0 (2000-10)]
Параллельные тексты EN-RU
The undervoltage trip automatically opens a circuit breaker when voltage drops to a value ranging between 35% to 70% of the line voltage.
The operation is instantaneous, and the circuit breaker cannot be reclosed until the voltage returns to 85% of line voltage.
Continuously energized, the undervoltage trip must be operating before the circuit breaker can be closed.
[LS Industrial Systems]Минимальный расцепитель напряжения вызывает срабатывание автоматического выключателя, если линейное напряжение защищаемой цепи падает до 35-70 % от номинального значения.
Срабатывание происходит мгновенно, после чего автоматический выключатель невозможно перевести во включенное положение до тех, пока линейное напряжение защищаемой цепи не повысится до 85 %.
Минимальный расцепитель постоянно находится под напряжением защищаемой цепи и всегда успевает сработать до того, как будет предпринята попытка включения автоматического выключателя.
[Перевод Интент]
В низковольтных автоматических выключателеях минимальный расцепитель напряжения является дополнительной принадлежностью, которая встраивается в гнездо автоматического выключателя
Дополнительные (электрические) принадлежности, встраиваемые в специальные гнезда автоматического выключателя:
1 - Левое гнездо;
2 - Автоматический выключатель;
3 - Правое гнездо.
Рис. LS Industrial SystemsНедопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
- low-voltage release
- under voltage release
- under voltage trip
- under voltage trip coil
- under voltage trip device
- under voltage trip unit
- undervoltage release
- undervoltage trip
- undervoltage trip device
- undervoltage trip unit
- UVT
FR
Русско-французский словарь нормативно-технической терминологии > минимальный расцепитель напряжения
-
4 классификационный ток ОПН
классификационный ток ОПН
Iкл
Амплитудное значение (более высокое амплитудное значение из двух полярностей, если ток асимметричен) активной составляющей тока промышленной частоты, которое используется для определения классификационного напряжения ОПН и нормируется изготовителем.
[ ГОСТ Р 52725-2007]EN
reference current of an arrester
peak value (the higher peak value of the two polarities if the current is asymmetrical) of the resistive component of a power-frequency current used to determine the reference voltage of the arrester
NOTE 1 The reference current will be high enough to make the effects of stray capacitances at the measured reference voltage of the arrester units (with designed grading system) negligible and is to be specified by the manufacturer.
NOTE 2 Depending on the nominal discharge current and/or line discharge class of the arrester, the reference current will be typically in the range of 0,05 mA to 1,0 mA per square centimetre of disc area for single column arresters.
[IEC 60099-4, ed. 2.0 (2004-05)]FR
courant de référence d'un parafoudre
valeur de crête (la plus grande des deux polarités si le courant est dissymétrique) de la composante résistive du courant à fréquence industrielle utilisée pour déterminer la tension de référence d'un parafoudre.
NOTE 1 Il convient que le courant de référence soit suffisamment élevé pour rendre négligeables les effets des capacités parasites aux tensions de référence mesurées sur les éléments de parafoudre (avec leur système de répartition) et qu’il soit spécifié par le constructeur.
NOTE 2 Fonction du courant de décharge nominal et/ou de la classe de décharge de ligne du parafoudre, il convient que le courant de référence soit typiquement dans la gamme de 0,05 mA à 1,0 mA par centimètre carré de surface de disque pour les parafoudres à colonne unique
[IEC 60099-4, ed. 2.0 (2004-05)]Тематики
- высоковольтный аппарат, оборудование...
EN
FR
Русско-французский словарь нормативно-технической терминологии > классификационный ток ОПН
-
5 линейный ток
линейный ток
Ток, протекающий в линейном проводнике трехфазной электрической цепи, соединяющем источник и приемник электрической энергии.EN
phase current, I
value of the current flowing in each phase of an electrical distribution system
[IEC 61557-12, ed. 1.0 (2007-08)]FR
courant de phase, I
valeur du courant circulant dans chaque phase d’un réseau de distribution électrique
[IEC 61557-12, ed. 1.0 (2007-08)]
Четырехпроводная система трехфазного токаНейтраль - обшая точка соединенных концов фазных обмоток генератора (источника питания). То же самое относится и к потребителю (нагрузке).
Линейные провода ( проводники) - проводники, присоединенные к началу фазных обмоток (А, В и С).
Звезда ( соединение звездой) - представленное на рисунке соединение, в котором начала обмоток соединены в одну общую точку.
Нулейвой провод ( проводник) или нулевой рабочий провод (проводник) - проводник соединяющий нейтрали генератора (источника питания) и потребителя (нагрузки). Нулевой провод выполняет роль обратного провода.
Линейное напряжение - напряжение между линейными проводами.
Фазное напряжение - напряжение между линейным и нулевым проводом.
Фазный ток - ток, протекающий по фазной обмотке генератора (источника питания) или потребителя.
Линейный ток - ток, протекающий по линейному проводу.
При соединении звездой линейный ток равен фазному.
При работе по нулевому проводу протекает ток, равный векторной сумме трех линейных токов: IА, IB и IC.
Если фазы нагружены равномерно, то ток нулевого провода равен нулю.
[На основе книги Кузнецов М. И. Основы электротехники. М, "Высшая Школа", 1964]Тематики
- электротехника, основные понятия
EN
FR
Русско-французский словарь нормативно-технической терминологии > линейный ток
-
6 отключающая способность (коммутационного аппарата или плавкого предохранителя)
отключающая способность (коммутационного аппарата или плавкого предохранителя)
Значение ожидаемого тока отключения, который способен отключать коммутационный аппарат или плавкий предохранитель при установленном напряжении в предписанных условиях эксплуатации и поведения.
Примечания
1 Напряжение устанавливается и условия предписываются в стандарте на соответствующий аппарат.
2 Для переменного тока это симметричное действующее значение периодической составляющей.
МЭК 60050(441-17-08)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
отключающая способность (коммутационного аппарата или предохранителя)
Значение ожидаемого тока отключения, который коммутационный аппарат или предохранитель способен отключить при заданном напряжении в предписанных условиях применения и поведения.
Примечание - Для коммутационных аппаратов отключающая способность может быть определена в соответствии с видом тока, предусмотренного в предписанных условиях, например отключающая способность при отключении ненагруженной линии, отключающая способность при отключении ненагруженного кабеля, отключающая способность при отключении одиночной конденсаторной батареи и т. д
[ ГОСТ Р 52726-2007]
отключающая способность коммутационного аппарата
Коммутационная способность коммутационного аппарата при отключении цепи.
[ ГОСТ 17703-72]EN
breaking capacity (of a switching device or a fuse)
a value of prospective current that a switching device or a fuse is capable of breaking at a stated voltage under prescribed conditions of use and behaviour
NOTE 1 – The voltage to be stated and the conditions to be prescribed are dealt with in the relevant publications.
NOTE 2 – For switching devices, the breaking capacity may be termed according to the kind of current included in the prescribed conditions, e.g. line-charging breaking capacity, cable charging breaking capacity, single capacitor bank breaking capacity, etc.
[IEV number 441-17-08]
[IEV number 441-01-49]FR
pouvoir de coupure (d'un appareil de connexion ou d'un fusible)
une valeur de courant présumé qu'un appareil de connexion ou un fusible est capable d'interrompre sous une tension fixée dans des conditions prescrites d'emploi et de comportement
NOTE 1 – La tension à fixer et les conditions à prescrire sont précisées dans les publications particulières.
NOTE 2 – Pour les appareils de connexion, le pouvoir de coupure peut être dénommé suivant le type de courant intervenant dans les conditions prescrites, par exemple: pouvoir de coupure de lignes à vide, pouvoir de coupure de câbles à vide, pouvoir de coupure d'une batterie de condensateurs unique, etc.
[IEV number 441-17-08]
[IEV number 441-01-49]
Недопустимые, нерекомендуемые
Примечание(1)- Мнение автора карточкиТематики
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- BC
- breaking capacity
- breaking capacity (of a switching device or a fuse)
- breaking current capacity
- IC
- interrupting capability
- interrupting capacity
- rupture capacity
- rupture rupturing capacity
DE
FR
Русско-французский словарь нормативно-технической терминологии > отключающая способность (коммутационного аппарата или плавкого предохранителя)
-
7 ток нагрузки
ток нагрузки
-EN
load current
current flowing through the line conductor/s
[IEC 61557-13, ed. 1.0 (2011-07)]
load current
the r.m.s. value of the current in any winding under service conditions
[IEC 60076-1, ed. 3.0 (2011-04)]
load current
current to which the devices are subjected to produce power loss P
[IEC 60749-34, ed. 2.0 (2010-10)]FR
courant de charge
courant circulant à travers le (les) conducteur(s) de ligne
[IEC 61557-13, ed. 1.0 (2011-07)]
courant de charge
<>la valeur efficace vraie (r.m.s.) du courant dans tout enroulement en conditions de service
[IEC 60076-1, ed. 3.0 (2011-04)]
courant de charge
courant auquel sont soumis les dispositifs pour produire la perte de puissance P
[IEC 60749-34, ed. 2.0 (2010-10)]Параллельные тексты EN-RU
If it is left ON or OFF for a long time, it is recommended to switch load current on a regular basis.
[LS Industrial Systems]Если (автоматический выключатель) продолжительное время находится во включенном или отключенном состоянии, то рекомендуется периодически коммутировать этим выключателем ток нагрузки.
[Перевод Интент]Тематики
- электротехника, основные понятия
EN
FR
Русско-французский словарь нормативно-технической терминологии > ток нагрузки
См. также в других словарях:
Value Line — Value Line, Inc.(NASDAQ|VALU), is a New York corporation founded in 1931 by Arnold Bernhard, best known for publishing the The Value Line Investment Survey , a stock analysis newsletter that s updated weekly and kept by subscribers in a large… … Wikipedia
Value Line Composite Index — The Value Line Composite Index is comprised of all of the companies that are included in the Value Line Investment Survey. There are currently 1,626 companies included in the index that are publicly listed on the following exchanges [ [http://www … Wikipedia
Value Line Index — An equal weighted stock index containing 1,700 companies from the NYSE, American Stock Exchange, Nasdaq and over the counter market. Also known as the Value Line Investment Survey . As this is an equal weighted index, each of the 1,700 stocks are … Investment dictionary
инвестиционый обзор агентства VALUE LINE — Инвестиционное консультационное агентство, которое осуществляет оценку 1700 акций с точки зрения соблюдения сроков и безопасности. Используя компьютерную модель, основанную на показателе прибыльности компаний, Value Line прогнозирует, какие акции … Финансово-инвестиционный толковый словарь
Acer Value Line — is a product line of low cost LCD monitors manufactured by Taiwan based computer company Acer.Most of LCD monitors from Value Line series are dedicated to home or office users. Most of them have a classic design and standard functions ideal for… … Wikipedia
Value Line investment survey — A proprietary service that ranks stocks for timeliness and safety. Bloomberg Financial Dictionary … Financial and business terms
Value Stream Mapping — is a Lean technique used to analyse the flow of materials and information currently required to bring a product or service to a consumer. At Toyota, where the technique originated, it is known as Material and Information Flow Mapping [Learning to … Wikipedia
Line moiré — is one type of moiré pattern; a pattern that appears when superposing two transparent layers containing correlated opaque patterns. Line moiré is the case when the superposed patterns comprise straight or curved lines. When moving the layer… … Wikipedia
Value added — refers to the additional value of a commodity over the cost of commodities used to produce it from the previous stage of production. An example is the price of gasoline at the pump over the price of the oil in it. In national accounts used in… … Wikipedia
line — I (ancestry) noun arrangement, avenue, beat, birth, blood, bloodline, channel, communication, course, derivation, descent, direction, dispatch, drift, epistle, family, stock, genealogy, heredity, idea, lane, letter, lineage, method, missive,… … Law dictionary
Value City Plaza — is a centrally located shopping plaza in downtown Cumberland, Maryland, bounded to the northeast by Queen City Drive and the main CSX Transportation line. The plaza forms the northern most entrance into the Downtown Cumberland Historic District… … Wikipedia