-
1 падение напряжения
1
падение напряжения
-
[IEV number 151-15-08]EN
voltage drop (1)
tension drop (1)
voltage between the terminals of a resistive element being part of an electric circuit due to the electric current through that element
[IEV number 151-15-08]FR
chute de tension (1), f
tension électrique produite aux bornes d’un élément résistif faisant partie d'un circuit électrique par le courant électrique qui circule dans cet élément
[IEV number 151-15-08]2
падение напряжения
-
[IEV number 151-15-09]EN
voltage drop (2)
tension drop (2)
change of the voltage between two given terminals of an electric circuit due to the change of the operating conditions
[IEV number 151-15-09]FR
chute de tension (2), f
variation de la tension électrique entre deux bornes données d'un circuit électrique due à une variation des conditions de fonctionnement
[IEV number 151-15-09]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > падение напряжения
-
2 падение или повышение напряжения при заданном режиме нагрузки
падение или повышение напряжения при заданном режиме нагрузки
Разность между напряжением холостого хода обмотки и напряжением на ее выводах при заданных нагрузке и коэффициенте мощности при условии, что к другой (или к одной из других) обмотке(ок) подведено напряжение, равное:
- номинальному, если трансформатор включен на основное ответвление (в этом случае напряжение холостого хода рассматриваемой обмотки равно номинальному);
- напряжению другого ответвления, на которое включен трансформатор. Падение или повышение напряжения обычно выражают в процентах напряжения холостого хода рассматриваемой обмотки.
Примечание — В многообмоточном трансформаторе падение или повышение напряжения зависит от нагрузки и коэффициента мощности не только данной обмотки, но и других обмоток
(МЭС 421-07-03).
[ ГОСТ 30830-2002]EN
voltage drop or rise for a specified load condition
voltage regulation for a specified load condition
the arithmetic difference between the no-load voltage of a winding and the voltage developed at the terminals of the same winding at a specified load and power factor, the voltage supplied to (one of) the other winding(s) being equal to:
- its rated value if the transformer is connected on the principal tapping (the no-load voltage of the former winding is then equal to its rated value);
- the tapping voltage if the transformer is connected on another tapping.
This difference is generally expressed as a percentage of the no-load voltage of the former winding
NOTE – For multi-winding transformers, the voltage drop or rise depends not only on the load and power factor of the winding itself, but also on the load and power factor of the other windings
[IEV number 421-07-03]FR
hute ou augmentation de tension pour une condition de charge spécifiée
différence arithmétique entre la tension à vide d'un enroulement et la tension en charge aux bornes du même enroulement pour un courant de charge et un facteur de puissance spécifiés, la tension appliquée à l'autre (ou à l'un des autres) enroulement(s) étant égale:
- à sa valeur assignée, si le transformateur est connecté sur la prise principale (la tension à vide du premier enroulement étant alors égale à sa valeur assignée);
- à la tension de prise si le transformateur est connecté sur une autre prise.
Cette différence s'exprime généralement sous la forme d'un pourcentage de la tension à vide du premier enroulement
NOTE – Pour les transformateurs à plus de deux enroulements, la chute ou l'augmentation de tension dépend non seulement de la charge et du facteur de puissance de l'enroulement lui-même, mais aussi de la charge et du facteur de puissance des autres enroulements.
[IEV number 421-07-03]Тематики
Классификация
>>>EN
- voltage drop or rise for a specified load condition
- voltage regulation for a specified load condition
DE
FR
Русско-французский словарь нормативно-технической терминологии > падение или повышение напряжения при заданном режиме нагрузки
-
3 удар по мячу с налёта
Dictionnaire russe-français universel > удар по мячу с налёта
-
4 перепад
перепад
Гидротехническое сооружение для сопряжения безнапорных участков водоёмов или водоводов, расположенных на разных уровнях
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > перепад
-
5 перепад электромагнитной индукции в магнитопроводе импульсного трансформатора
- saut de l’induction dans le circuit magnétique
перепад электромагнитной индукции в магнитопроводе импульсного трансформатора
Разность между электромагнитной индукцией на предельной петле гистерезиса и остаточной индукцией при одностороннем перемагничивании импульсного трансформатора
[ ГОСТ 20938-75]ENТематики
Классификация
>>>Синонимы
EN
DE
- Sprung der elektromagnetischen Induktion im Magnetkern des Impulstransformators
FR
- saut de l’induction dans le circuit magnétique
82. Перепад электромагнитной индукции в магнитопроводе импульсного трансформатора
Перепад индукции в магнитопроводе
D. Sprung der elektromagnetischen Induktion im Magnetkern des Impulstransformators
E. Induction drop in a core
F. Saut de l’induction dans le circuit magnetique
Разность между электромагнитной индукцией на предельной петле гистерезиса и остаточной индукцией при одностороннем перемагничивании импульсного трансформатора
Источник: ГОСТ 20938-75: Трансформаторы малой мощности. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > перепад электромагнитной индукции в магнитопроводе импульсного трансформатора
-
6 песчаная раковина
песчаная раковина
Дефект в виде полости, полностью или частично заполненной формовочным материалом.
[ ГОСТ 19200-80]Тематики
Обобщающие термины
EN
DE
FR
34. Песчаная раковина
D. Sandeinschluss
E. Sand holes, drop
F. Inclusion de sable
Дефект в виде полости, полностью или частично заполненной формовочным материалом
Источник: ГОСТ 19200-80: Отливки из чугуна и стали. Термины и определения дефектов оригинал документа
Русско-французский словарь нормативно-технической терминологии > песчаная раковина
-
7 дроп
ngener. drop (машина для погрузки судов) -
8 дроп-атака
nmed. Drop attack -
9 сбой схемы
nbrit.engl. drop-out de circuit -
10 синкопальный вертебральный синдром
adjmed. Drop attackDictionnaire russe-français universel > синкопальный вертебральный синдром
-
11 схемное прерывание
adjbrit.engl. drop-out de circuit -
12 выпадение сигнала (записи-воспроизведения)
выпадение сигнала (записи-воспроизведения)
Кратковременный перерыв или недопустимое уменьшение воспроизводимого сигнала, обусловленное дефектами или загрязнением носителя записи или сигналограммы, либо недостатками работы устройств записи и (или) воспроизведения.
[ ГОСТ 13699-91]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выпадение сигнала (записи-воспроизведения)
-
13 главный распределительный щит
главный распределительный щит (ГРЩ)
Распределительный щит, через который снабжается электроэнергией все здание или его обособленная часть. Роль ГРЩ может выполнять ВРУ или щит низкого напряжения подстанции.
[ПУЭ]
главный распределительный щит
Электрощит в здании, обеспечивающий распределение энергии между подключенными к нему нагрузками и включение аварийных систем при падении напряжения.
[ ГОСТ Р 51321. 3-99 ( МЭК 60439-3-90)]
[ ГОСТ Р 50571.28-2006]EN
main distribution board
board in the building which fulfils all the functions of a main electrical distribution for the supply building area assigned to it and where the voltage drop is measured for operating the safety services
[IEC 60364-7-710, ed. 1.0 (2002-11)]FR
tableau général de distribution
tableau de distribution dans le bâtiment remplissant toutes les fonctions d’un tableau général de distribution pour l’alimentation de la zone qui lui est dédiée et où la chute de tension est mesurée pour le fonctionnement des services de sécurité
[IEC 60364-7-710, ed. 1.0 (2002-11)]
Главный распределительный щит (ГРЩ) на ток 6300 А
[http://www.uzoelectro.ru/catalogue/group-383/product-36465/ ]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
- электроустановки
Синонимы
EN
- feeder switchboard
- m.s.b.
- main distributing frame
- main distribution board
- main distribution switchboard
- Main Low Voltage Switchboard
- main low-voltage distribution switchboard
- main switchboard
- MLVS
- MSB
- power center
FR
Русско-французский словарь нормативно-технической терминологии > главный распределительный щит
-
14 дефолиация
дефолиация
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
defoliation
1) The drop of foliage from plants caused by herbicides such as Agent Orange, diuron, triazines, all of which interfere with photosynthesis. The use of defoliants, as in Vietnam or in jungle clearance for agriculture, can permanently destroy tropical forests. Once the tree cover is removed, the soil is subjected to erosion and precious nutrients are rapidly leached away.
2) Destroying (an area of jungle, forest, etc.) as by chemical sprays or incendiary bombs, in order to give enemy troops or guerilla forces no place of concealment.
(Source: PORT / WEBSTE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > дефолиация
-
15 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
16 испытательный ток
испытательный ток
Ток, вызывающий падение напряжения в цепи
[ ГОСТ Р 61557-1-2006]EN
test current
current that causes a voltage drop in a circuit
[IEC 61557-3, ed. 2.0 (2007-01)]FR
courant d'essai
dispositif provoquant une chute de tension dans un circuit
[IEC 61557-3, ed. 2.0 (2007-01)]-
Если испытательный ток ниже номинальной наибольшей отключающей способности, на выходной стороне выключателя следует предусмотреть дополнительные импедансы Z1.
[ ГОСТ Р 50345-99( МЭК 60898-95)] - При испытании однофазным переменным током или постоянным током испытательный ток в цепи должен быть не ниже, установленного в стандартах на конкретные виды аппаратов.
-
Испытательный ток следует определять с помощью осциллографа.
[ ГОСТ 2933-83]
Тематики
- электротехника, основные понятия
EN
FR
Русско-французский словарь нормативно-технической терминологии > испытательный ток
-
Если испытательный ток ниже номинальной наибольшей отключающей способности, на выходной стороне выключателя следует предусмотреть дополнительные импедансы Z1.
-
17 кривая спада
кривая спада
Очертания продольного профиля свободной поверхности водотока, глубина которого уменьшается вниз по течению
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
кривая спада
Кривая свободной поверхности потока, глубина которого уменьшается вдоль направления течения.
[СО 34.21.308-2005]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > кривая спада
-
18 крупнокапельное опрыскивание пестицидом
- pulvérisation du pesticide par gouttes grosses (pas moins de 0,15 mm)
крупнокапельное опрыскивание пестицидом
Опрыскивание растений пестицидом, при котором не менее 80 % жидкости разбрызгивается в виде капель размером не менее 0,15 мм.
[ ГОСТ 21507-81]Тематики
Обобщающие термины
EN
DE
FR
- pulvérisation du pesticide par gouttes grosses (pas moins de 0,15 mm)
Русско-французский словарь нормативно-технической терминологии > крупнокапельное опрыскивание пестицидом
-
19 ламель ткацкой машины
ламель ткацкой машины (153)
Составная часть ламельного основонаблюдателя в виде металлической пластины, подвешенная на нить основы, которая при ее обрыве падает на планку электрического контакта или зубчатую рейку механического движения для подачи сигнала на останов машины.
[ ГОСТ 27876-88( СТ СЭВ 6103-87, СТ СЭВ 6104-87, ИСО 5247/2-89)]Тематики
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ламель ткацкой машины
-
20 ламельный основонаблюдатель
ламельный основонаблюдатель
Основонаблюдатель, в котором сигнал на останов машины при обрыве нити основы подается при помощи ламели.
[ ГОСТ 27876-88( СТ СЭВ 6103-87, СТ СЭВ 6104-87, ИСО 5247/2-89)]Тематики
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ламельный основонаблюдатель
- 1
- 2
См. также в других словарях:
Drop.io — URL drop.io Slogan Simple, private sharing. Available language(s) English Owner … Wikipedia
Drop by drop — Drop Drop (dr[o^]p), n. [OE. drope, AS. dropa; akin to OS. dropo, D. drop, OHG. tropo, G. tropfen, Icel. dropi, Sw. droppe; and Fr. AS. dre[ o]pan to drip, drop; akin to OS. driopan, D. druipen, OHG. triofan, G. triefen, Icel. drj[=u]pa. Cf.… … The Collaborative International Dictionary of English
Drop D tuning — Drop D tuning. Drop D tuning, also known as DADGBE, is an alternate, or scordatura, form of guitar tuning specifically, a dropped tuning in which the lowest (sixth) string is tuned down ( dropped ) from the usual E of standard tuning by one whole … Wikipedia
Drop Dead Diva — Inter title Genre Comedy drama Fantasy Legal Drama Created by … Wikipedia
Drop Tower: Scream Zone — at Canada s Wonderland California s Great America Opening date March 1996 … Wikipedia
Drop — (dr[o^]p), n. [OE. drope, AS. dropa; akin to OS. dropo, D. drop, OHG. tropo, G. tropfen, Icel. dropi, Sw. droppe; and Fr. AS. dre[ o]pan to drip, drop; akin to OS. driopan, D. druipen, OHG. triofan, G. triefen, Icel. drj[=u]pa. Cf. {Drip},… … The Collaborative International Dictionary of English
Drop curtain — Drop Drop (dr[o^]p), n. [OE. drope, AS. dropa; akin to OS. dropo, D. drop, OHG. tropo, G. tropfen, Icel. dropi, Sw. droppe; and Fr. AS. dre[ o]pan to drip, drop; akin to OS. driopan, D. druipen, OHG. triofan, G. triefen, Icel. drj[=u]pa. Cf.… … The Collaborative International Dictionary of English
Drop forging — Drop Drop (dr[o^]p), n. [OE. drope, AS. dropa; akin to OS. dropo, D. drop, OHG. tropo, G. tropfen, Icel. dropi, Sw. droppe; and Fr. AS. dre[ o]pan to drip, drop; akin to OS. driopan, D. druipen, OHG. triofan, G. triefen, Icel. drj[=u]pa. Cf.… … The Collaborative International Dictionary of English
Drop hammer — Drop Drop (dr[o^]p), n. [OE. drope, AS. dropa; akin to OS. dropo, D. drop, OHG. tropo, G. tropfen, Icel. dropi, Sw. droppe; and Fr. AS. dre[ o]pan to drip, drop; akin to OS. driopan, D. druipen, OHG. triofan, G. triefen, Icel. drj[=u]pa. Cf.… … The Collaborative International Dictionary of English
Drop kick — Drop Drop (dr[o^]p), n. [OE. drope, AS. dropa; akin to OS. dropo, D. drop, OHG. tropo, G. tropfen, Icel. dropi, Sw. droppe; and Fr. AS. dre[ o]pan to drip, drop; akin to OS. driopan, D. druipen, OHG. triofan, G. triefen, Icel. drj[=u]pa. Cf.… … The Collaborative International Dictionary of English
Drop lake — Drop Drop (dr[o^]p), n. [OE. drope, AS. dropa; akin to OS. dropo, D. drop, OHG. tropo, G. tropfen, Icel. dropi, Sw. droppe; and Fr. AS. dre[ o]pan to drip, drop; akin to OS. driopan, D. druipen, OHG. triofan, G. triefen, Icel. drj[=u]pa. Cf.… … The Collaborative International Dictionary of English