-
1 постоянная (счетчика)
постоянная (счетчика)
-
[IEV number 314-07-08]EN
(meter) constant
value expressing the relation between the active energy registered by a meter and the corresponding value of the test output.
NOTE – If this value is a number of pulses, the constant should be either pulses per kilowatt-hour (imp/kWh) or watt-hours per pulse (Wh/imp)
[IEV number 314-07-08]FR
co nstante (du compteur)
valeur exprimant la relation entre l’énergie enregistrée par un compteur et la valeur correspondante donnée par le dispositif de sortie d’essai
NOTE – Si cette valeur est un nombre d’impulsions, la constante doit être soit le nombre d’impulsions par kilowattheure (imp/kWh), soit le nombre de wattheures par impulsion (Wh/imp)
[IEV number 314-07-08]Тематики
- измерение электр. величин в целом
- счетчик электроэнергии
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > постоянная (счетчика)
-
2 рабочее напряжение в системе электроснабжения
рабочее напряжение в системе электроснабжения
Значение напряжения при нормальном режиме в рассматриваемый момент времени в данной точке системы электроснабжения.
[ ГОСТ 23875-88]EN
operating voltage (in a system)
the value of the voltage under normal conditions, at a given instant and a given point of the system
NOTE – This value may be expected, estimated or measured.
[IEV number 601-01-22]FR
tension de service (dans un réseau)
valeur de la tension en service normal à un instant et en un lieu donnés de ce réseau
NOTE – Cette valeur peut être souhaitée, estimée ou mesurée.
[IEV number 601-01-22]Тематики
EN
DE
FR
Смотри также
11. Рабочее напряжение в системе электроснабжения
D. Betriebsspannung
E. Operating voltage (in a system)
F. Tension de service (dans un reseau)
Значение напряжения при нормальном режиме в рассматриваемый момент времени в данной точке системы электроснабжения
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > рабочее напряжение в системе электроснабжения
3 полное сопротивление короткого замыкания пары обмоток
полное сопротивление короткого замыкания пары обмоток
Сопротивление, равное Z = R + jХ, Ом, определяемое при номинальной частоте и расчетной температуре между выводами одной из обмоток пары, при замкнутой накоротко другой обмотке этой пары и разомкнутых остальных обмотках при их наличии. Для трехфазного трансформатора полное сопротивление короткого замыкания пары обмоток является полным сопротивлением фазы (в эквивалентной схеме соединения «звезда»).
В трансформаторе, имеющем обмотку с ответвлениями, полное сопротивление короткого замыкания относят к конкретному ответвлению. Если в НД не оговорено иное, выбирают основное ответвление.
Примечание — Полное сопротивление короткого замыкания пары обмоток может быть выражено в относительных значениях z, например в процентах базисного полного сопротивления короткого замыкания Zбаз той же обмотки пары
Z=100Z/Zбаз
Где Zбаз=U2/Sном
(для трехфазных и однофазных трансформаторов), Ом (U — напряжение (номинальное или напряжение ответвления) обмотки, к которой относятся Z и Zбаз, В; Sном — номинальная мощность основного ответвления трансформатора, В•А).
Относительное значение полного сопротивления короткого замыкания может быть также определено как отношение напряжения, приложенного к данной обмотке в опыте короткого замыкания, вызывающего протекание через эту обмотку номинального тока (либо тока ответвления), к номинальному напряжению этой обмотки (либо напряжению ответвления). Это приложенное напряжение определяют как напряжение короткого замыкания (МЭС 421-07-01) данной пары обмоток и, как правило, выражают в процентах
(МЭС 421-07-02).
[ ГОСТ 30830-2002]EN
short-circuit impedance of a pair of windings
the equivalent star connection impedance related to one of the windings, for a given tapping and expressed in ohms per phase, at rated frequency, measured between the terminals of a winding when the other winding is short-circuited
NOTE – This value is normally related to the appropriate reference temperature
[IEV number 421-07-02]FR
impédance de court-circuit d'une paire d'enroulements
impédance équivalente en connexion étoile, rapportée à l'un des enroulements, pour une prise donnée et exprimée en ohms par phase, à la fréquence assignée, mesurée aux bornes d'un enroulement lorsque l'autre enroulement est en court-circuit
NOTE – Cette valeur est normalement rapportée à une température de référence appropriée.
[IEV number 421-07-02]Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > полное сопротивление короткого замыкания пары обмоток
4 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
5 падение или повышение напряжения при заданном режиме нагрузки
падение или повышение напряжения при заданном режиме нагрузки
Разность между напряжением холостого хода обмотки и напряжением на ее выводах при заданных нагрузке и коэффициенте мощности при условии, что к другой (или к одной из других) обмотке(ок) подведено напряжение, равное:
- номинальному, если трансформатор включен на основное ответвление (в этом случае напряжение холостого хода рассматриваемой обмотки равно номинальному);
- напряжению другого ответвления, на которое включен трансформатор. Падение или повышение напряжения обычно выражают в процентах напряжения холостого хода рассматриваемой обмотки.
Примечание — В многообмоточном трансформаторе падение или повышение напряжения зависит от нагрузки и коэффициента мощности не только данной обмотки, но и других обмоток
(МЭС 421-07-03).
[ ГОСТ 30830-2002]EN
voltage drop or rise for a specified load condition
voltage regulation for a specified load condition
the arithmetic difference between the no-load voltage of a winding and the voltage developed at the terminals of the same winding at a specified load and power factor, the voltage supplied to (one of) the other winding(s) being equal to:
- its rated value if the transformer is connected on the principal tapping (the no-load voltage of the former winding is then equal to its rated value);
- the tapping voltage if the transformer is connected on another tapping.
This difference is generally expressed as a percentage of the no-load voltage of the former winding
NOTE – For multi-winding transformers, the voltage drop or rise depends not only on the load and power factor of the winding itself, but also on the load and power factor of the other windings
[IEV number 421-07-03]FR
hute ou augmentation de tension pour une condition de charge spécifiée
différence arithmétique entre la tension à vide d'un enroulement et la tension en charge aux bornes du même enroulement pour un courant de charge et un facteur de puissance spécifiés, la tension appliquée à l'autre (ou à l'un des autres) enroulement(s) étant égale:
- à sa valeur assignée, si le transformateur est connecté sur la prise principale (la tension à vide du premier enroulement étant alors égale à sa valeur assignée);
- à la tension de prise si le transformateur est connecté sur une autre prise.
Cette différence s'exprime généralement sous la forme d'un pourcentage de la tension à vide du premier enroulement
NOTE – Pour les transformateurs à plus de deux enroulements, la chute ou l'augmentation de tension dépend non seulement de la charge et du facteur de puissance de l'enroulement lui-même, mais aussi de la charge et du facteur de puissance des autres enroulements.
[IEV number 421-07-03]Тематики
Классификация
>>>EN
- voltage drop or rise for a specified load condition
- voltage regulation for a specified load condition
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > падение или повышение напряжения при заданном режиме нагрузки
6 показатель абсорбции органических галогенов
показатель абсорбции органических галогенов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
AOX value
Organic halogens subject to absorption. This is a measure of the amount of chlorine (and other halogens) combined with organic compounds. (Source: PORT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > показатель абсорбции органических галогенов
7 синхронное реактивное сопротивление по продольной оси
синхронное реактивное сопротивление по продольной оси
-EN
direct-axis synchronous reactance
the quotient of the sustained value of that fundamental a.c. component of armature voltage, which is produced by the total direct-axis primary flux due to direct-axis armature current, and the value of the fundamental a.c. component of this current, the machine running at rated speed
[IEV ref 411-50-07]FR
réactance synchrone longitudinale
quotient de la valeur, en régime établi, du terme fondamental de la composante de la tension d'induit produite par le flux longitudinal total dû au courant d'induit longitudinal, par la valeur du terme fondamental de ce courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-07]
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > синхронное реактивное сопротивление по продольной оси
8 аналоговый (измерительный) прибор
аналоговый (измерительный) прибор
аналоговый показывающий прибор
-
[IEV number 312-02-09]EN
analogue (measuring) instrument
analogue indicating instrument
measuring instrument whose indication is a continuous function of the corresponding value of the measurand or of the input signal
NOTE – This term relates to the form of presentation of the indication, not to the principle of operation of the instrument.
Source: ≈ VIM 4.10
[IEV number 312-02-09]FR
appareil de mesure (à affichage) analogique
appareil (de mesure) analogique
appareil de mesure dont l'indication est une fonction continue de la valeur correspondante du mesurande ou du signal d’entrée
NOTE – Ce terme se rattache à la forme de présentation de l’indication, non au principe de fonctionnement de l’appareil.
Source: ≈ VIM 4.10
[IEV number 312-02-09]Тематики
- измерение электр. величин в целом
Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > аналоговый (измерительный) прибор
9 время срабатывания электрического реле
время срабатывания электрического реле
Время от момента, когда входная воздействующая или характеристическая величина электрического реле, находящегося в начальном или исходном состоянии, принимает в заданных условиях определенное значение до момента, когда реле завершает срабатывание
[ ГОСТ 16022-83]EN
operate time
for a relay which is in the release condition (initial condition) the time interval between the instant a specified value of the input energizing quantity (characteristic quantity) is applied under specified condition and the instant when the relay switches
NOTE – This term is used only when the relay has output circuits of the same type and no precision is required according to contact time difference.
[IEV number 446-17-09]FR
temps de fonctionnement
temps d'action (terme déconseillé, utilisé pour les relais de tout ou rien)
pour un relais qui est dans l'état de repos ou dans un état initial, temps écoulé entre l'instant où la grandeur d'alimentation d'entrée ou la grandeur caractéristique prend, dans des conditions spécifiées, une valeur définie et l'instant où le relais commute
NOTE – Ce terme n'est utilisé que lorsque le relais ne comporte que des circuits de sortie de même nature et qu'aucune précision n'est nécessaire quant à la dispersion des temps de contact.
[IEV number 446-17-09]Тематики
EN
DE
FR
122. Время срабатывания электрического реле
D. Betätigungszeit
E. Operate time
F. Temps de fonctionnement;
Temps d’action (pour relais de tout ou rien)
Время от момента, когда входная воздействующая или характеристическая величина электрического реле, находящегося в начальном или исходном состоянии, принимает в заданных условиях определенное значение до момента, когда реле завершает срабатывание
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > время срабатывания электрического реле
10 высокое напряжение
1
высокое напряжение
-
[IEV number 151-15-05]EN
high voltage (1)
high tension (1)
HV (1), abbreviation
voltage having a value above a conventionally adopted limit
NOTE – An example is the set of upper voltage values used in bulk power systems.
Source: 601-01-27 MOD
[IEV number 151-15-05]FR
haute tension (1), f
2
HT (1), abréviation
tension électrique de valeur supérieure à une limite adoptée par convention
NOTE – Un exemple est l'ensemble des tensions les plus élevées utilisées dans les réseaux de production-transport d'énergie électrique.
Source: 601-01-27 MOD
[IEV number 151-15-05]высокое напряжение
-EN
High Voltage
HV
systems with nominal voltage in range above 1 000 V a.c. and up to and including 15 kV a.c.
NOTE This definition differs from the conventional definition.
[IEC/PAS 60092-510, ed. 1.0 (2009-04)]FR
-
Синонимы
- ВН
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > высокое напряжение
11 диапазон регулирования (в трансформаторах)
диапазон регулирования
Диапазон изменения коэффициента ответвления, выраженный в процентах.
Примечание — Если коэффициент ответвления изменяется от 100 + а до 100 — b, то диапазон регулирования выражается в «+а %», «—b %» или «± а %», если а = B
(МЭС 421-05-07).
[ ГОСТ 30830-2002]EN
tapping range
the variation range of the tapping factor expressed as a percentage, compared with the value "100"
NOTE – If this factor ranges from 100 + a to 100 - b, the tapping range is said to be: +a % -b % or ± a % if a = b
[IEV number 421-05-07]FR
étendue de prises
étendue de variation du facteur de prise exprimé sous la forme d'un pourcentage, par rapport à la valeur "100"
NOTE – Si ce facteur varie de 100 + a à 100 - b, l'étendue de prises s'exprime par +a %, - b %ou ± a% si a = b.
[IEV number 421-05-07]Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > диапазон регулирования (в трансформаторах)
12 ждущая развертка
ждущая развертка
-
[IEV number 314-06-12]EN
triggered sweep
mode of operation of a triggered time base in which the beginning of every sweep coincides with a predetermined point of the displayed quantity, thus producing a stable display when this quantity is periodic
NOTE – In triggered sweep mode, the internal trigger signal can be produced to correspond with any predetermined value of the displayed quantity on either the positive-going or negative-going slopes
[IEV number 314-06-12]FR
balayage déclenché
fonctionnement d'une base de temps déclenchée dans lequel le début de chaque balayage coïncide avec un point prédéterminé de la grandeur représentée, produisant ainsi une image stable lorsque cette grandeur est périodique
NOTE – Dans le cas du balayage déclenché, le signal de déclenchement interne peut être produit pour toute valeur prédéterminée de la grandeur représentée, soit sur la pente positive, soit sur la pente négative.
[IEV number 314-06-12]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > ждущая развертка
13 коэффициент амплитудной модуляции
коэффициент амплитудной модуляции
-
[IEV number 314-08-04]EN
amplitude modulation factor
ratio, for amplitude modulation, of half the difference of the maximum and minimum amplitudes to the mean value of the amplitude
NOTE – This definition does not apply to asymmetrical modulation or over-modulation.
Source: 702-06-19
[IEV number 314-08-04]FR
taux de modulation d'amplitude
rapport, en modulation d'amplitude, de la demi-différence entre les amplitudes maximale et minimale à la valeur moyenne de l'amplitude
NOTE – Cette définition ne s'applique pas aux cas de modulation asymétrique ou de surmodulation.
Source: 702-06-19
[IEV number 314-08-04]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент амплитудной модуляции
14 коэффициент ответвления
коэффициент ответвления (соответствующий конкретному ответвлению)
Отношение Uотв/Uном (коэффициент ответвления) либо 100 Uотв/Uном ((коэффициент ответвления, выраженный в процентах), где
Uном — номинальное напряжение обмотки, В (см. 3.4.3), a
Uотв — напряжение, возникающее при холостом ходе между выводами обмотки, присоединенной к данному ответвлению, при приложении номинального напряжения к обмотке без ответвлений, В.
Примечание — Это определение не распространяется на последовательную обмотку линейного регулировочного трансформатора (см. 3.1.3), для которого коэффициент ответвления, выраженный в процентах, относится к напряжению обмотки возбуждения или обмотки сетевого трансформатора, связанного с линейным регулировочным трансформатором
(МЭС 421-05-03).
[ ГОСТ 30830-2002]EN
tapping factor
the ratio Ud/ UN (tapping factor) or 100 Ud/ UN (tapping factor expressed as a percentage)
where:
UN is the rated voltage of the winding
Ud is the voltage which would be developed at no-load at the terminals of the winding, connected on the tapping concerned, by applying rated voltage to an untapped winding
NOTE – The tapping factor expresses the relative value of the "effective number of turns" of the tapped winding at the relevant tapping, the basis 1 being the effective number of turns of this winding at the principal tapping
[IEV number 421-05-03]FR
facteur de prise
rapport Ud/ UN (facteur de prise) ou 100 Ud/ UN (facteur de prise exprimé sous la forme d'un pourcentage)
où:
UN est la tension assignée de l'enroulement,
Ud est la tension qui serait développée aux bornes de l'enroulement, connecté sur la prise considérée, en fonctionnement à vide, en appliquant à un enroulement sans prise sa tension assignée
NOTE – Le facteur de prise exprime la valeur relative du "nombre effectif de spires" de l'enroulement à prises pour la prise considérée, la base 1 étant le nombre effectif de spires de cet enroulement pour la prise principale.
[IEV number 421-05-03]Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент ответвления
15 номинальное напряжение изоляции (соединительного устройства)
напряжение по изоляции
Напряжение, определяемое изготовителем для данного соединителя и его составных частей, с которыми соотносятся испытания на электрическую прочность изоляции, воздушные зазоры и расстояния утечки.
[ ГОСТ Р 51323.1-99]
номинальное напряжение изоляции (соединительного устройства)
-
[IEV number 442-06-39]EN
rated insulation voltage, (of a connecting device)
phase/neutral or phase/phase voltage value assigned to the connecting device by the manufacturer, this device being intended to be used in installations, the voltage supply of which does not exceed the rated insulation voltage of the connecting device itself
NOTE – Rated insulation voltage is always understood to be between live parts and not between live parts and earth (ground).
[IEV number 442-06-39]FR
tension d'isolement assignée (d'un dispositif de connexion)
valeur de la tension phase/neutre ou phase/phase assignée par le constructeur du dispositif de connexion, celui-ci étant prévu pour être utilisé dans des installations dont la tension d'alimentation ne dépasse pas la tension d'isolement assignée du dispositif de connexion lui-même
NOTE – La tension d'isolement assignée est toujours comprise comme la tension entre parties sous tension et non entre parties sous tension et terre.
[IEV number 442-06-39]Тематики
EN
- rated insulation voltage, (of a connecting device)
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > номинальное напряжение изоляции (соединительного устройства)
16 плавкий предохранитель
плавкий предохранитель
Коммутационный аппарат, который посредством плавления одного или нескольких своих специально спроектированных и калиброванных элементов размыкает цепь, в которую он включен, и отключает ток, когда он превышает заданную величину в течение достаточного времени. Плавкий предохранитель содержит все части, образующие укомплектованный аппарат.
МЭК 60050(441-18-01).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
плавкий предохранитель
Аппарат, который вследствие расплавления одного или нескольких специально спроектированных и рассчитанных элементов размыкает цепь, в которую он включен, отключая ток, превышающий заданное значение в течение достаточно продолжительного времени. В состав плавкого предохранителя входят все части, образующие аппарат в комплекте
[ ГОСТ Р 50339. 0-2003 ( МЭК 60269-1-98)]
предохранитель
Коммутационный электрический аппарат, предназначенный для отключения защищаемой цепи посредством разрушения специально предусмотренных для этого токоведущих частей под действием тока, превышающего определенную величину.
[ ГОСТ 17703-72]
предохранитель
Устройство для разрыва электрических цепей при силе тока, превышающей допустимое значение
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
fuse
a device that by the fusing of one or more of its specially designed and proportioned components, opens the circuit in which it is inserted by breaking the current when this exceeds a given value for a sufficient time. The fuse comprises all the parts that form the complete device
[IEV number 441-18-01 ]FR
fusible
coupe-circuit à fusibles
appareil dont la fonction est d'ouvrir par la fusion d'un ou de plusieurs de ses éléments conçus et calibrés à cet effet le circuit dans lequel il est inséré en coupant le courant lorsque celui-ci dépasse pendant un temps suffisant une valeur donnée. Le fusible comprend toutes les parties qui constituent l'appareil complet
[IEV number 441-18-01 ]Настоящий стандарт распространяется на плавкие предохранители на номинальный ток от 2 до 2500 А, номинальное напряжение переменного тока до 1000 В и постоянного тока до 1200 В, устанавливаемые в комплектные устройства и предназначенные для защиты при перегрузках и коротких замыканиях силовых и вспомогательных цепей электроустановок промышленных предприятий, общественных и жилых зданий, изготовляемые для нужд народного хозяйства и экспорта и номинальное напряжение до 3000 В для защиты полупроводниковых устройств.
3.2.14. Предохранители должны быть сконструированы таким образом, чтобы отключать электрическую цепь при токах отключения в пределах: от условного тока плавления — для предохранителей с плавкими вставками типов g и gR или от наименьшего тока отключения, установленного в стандартах или технических условиях на предохранители конкретных серий и типов, для предохранителей с плавкими вставками типов а и aR — до наибольшего тока отключения
[ ГОСТ 17242-86]... токи, при которых проводят испытания, предназначенные для проверки способности данного плавкого предохранителя срабатывать удовлетворительно в диапазоне малых сверхтоков.
[ ГОСТ Р 50339.0-2003]... Если неисправность заканчивается срабатыванием плавкого предохранителя или если плавкий предохранитель не срабатывает примерно в течение 1 с, то...
[ ГОСТ Р 52319-2005]ЭЛЕКТРИЧЕСКИЕ ПАРАМЕТРЫ И ХАРАКТЕНИСТИКИ ПРЕДОХРАНИТЕЛЕЙ
(взято из ГОСТ 17242-86)-
Для держателя (или основания) предохранителя:
- номинальное напряжение;
- номинальный ток;
- род тока и номинальная частота для переменного тока;
- допустимые потери мощности;
- число полюсов, если их более одного.
-
Для плавкой вставки:
- номинальное напряжение;
- номинальный ток;
- род тока и номинальная частота для переменного тока;
- потери мощности;
- время-токовые характеристики с указанием коэффициентов K1 и K2 для плавких вставок типа а;
- перегрузочная способность;
- диапазон токов отключения;
- наибольшая отключающая способность;
- наименьший ток отключения для плавких вставок типа а;
- характеристика пропускаемого тока;
- характеристики интегралов Джоуля;
- перенапряжение и характеристика перенапряжения для плавких вставок типов aR и gR;
- условия селективности (при необходимости);
- электрическое сопротивление плавкой вставки в холодном состоянии (допускается указать в рабочих чертежах, утвержденных в установленном порядке).
-
Для предохранителя:
- степень защиты по ГОСТ 14255—69;
- номинальное напряжение, номинальный ток и коммутационная способность свободных контактов (при их наличии).
Параллельные тексты EN-RU
Check to make sure that fuse F1 on power supply module V is not fused.
If the fuse is defective, it should not be replaced without determining the cause of failure.
If a fuse is replaced without eliminating the problem, there is the danger that the damage will spread.
[Schneider Electric]Убедитесь в исправности предохранителя F1 в модуле питания V.
Если предохранитель оказался неисправным, то прежде чем заменить его необходимо установить причину возникновения неисправности.
Замена предохранителя без выяснения причины его срабатывания может привести к повторению срабатывания.
[Перевод Интент]High voltage system may embrace a fuse.
Note that a fuse may not be manually adjusted as the circuit breaker relay does so the fuse choice for the appropriate purpose/circuit adaptation is deemed most important.
[LS Industrial Systems]Высоковольтная система < электропитания> может содержать предохранители.
Обратите внимание! Предохранитель нельзя настроить, как это можно сделать с расцепителем автоматического выключателя. Поэтому предохранитель необходимо выбрать так, чтобы он как можно точнее соотвествовал конкретным условиям защиты аппарата или участка цепи.
[Перевод Интент]
Тематики
Классификация
>>>Обобщающие термины
Действия
- защищать при перегрузках и коротких замыканиях
- отключать электрическую цепь
- срабатывание предохранителя
Синонимы
EN
- cutoff
- electric fuse
- fu
- fuse
- fuse switch
- fusible cutout
- fusible plug
- fusible switch
- plug fuse
- protective fuse
- safety cutoff
- safety fuse
- safety plug
- SF
- thermal fuse
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > плавкий предохранитель
17 телеизмерительная аппаратура
телеизмерительная аппаратура
-
[IEV number 312-02-16]EN
telemeasuring equipment
assembly of instruments intended to indicate or record the value of the measurand at a distance from the measuring point, using telecommunications techniques
NOTE – The use of the term "telemetering equipment" is deprecated in this sense.
[IEV number 312-02-16]FR
équipement de télémesure
ensemble d'appareils qui sert à indiquer ou à enregistrer la valeur du mesurande à une certaine distance du point de mesure, au moyen de télécommunications
NOTE – En anglais, l’utilisation de l’expression "telemetering equipment" est désapprouvée dans ce sens.
[IEV number 312-02-16]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > телеизмерительная аппаратура
18 ток отсечки
ток отсечки
Максимальное мгновенное значение тока, достигаемое в процессе отключения тока коммутационным аппаратом или плавким предохранителем.
МЭК 60050 (441-17-12).
Примечание. Понятие особенно важно, когда коммутационный аппарат или плавкий предохранитель срабатывает так, что ожидаемый пиковый ток цепи не достигается.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
cut-off current
let-through current
the maximum instantaneous value of current attained during the breaking operation of a switching device or a fuse
NOTE – This concept of particular importance when the switching device or the fuse operates in such a manner that the prospective peak current of the circuit is not reached.
[IEV number 441-17-12]FR
courant coupé limité
valeur instantanée maximale du courant atteinte au cours de la coupure effectuée par un appareil de connexion ou un fusible
NOTE – Cette notion est d'importance particulière si l'appareil de connexion ou le fusible fonctionne de telle manière que la valeur de crête du courant présumé du circuit n'est pas atteinte.
[IEV number 441-17-12]Примечание
Более подробно о токе отсечки см. " защитная характеристика автоматического выключателя"Тематики
- выключатель автоматический
- выключатель, переключатель
- предохранитель
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > ток отсечки
19 трансформатор тока для защиты
трансформатор тока для защиты
Трансформатор тока, предназначенный для передачи сигнала измерительной информации на устройства защиты и управления.
[ ГОСТ 18685-73]EN
protective current transformer
a current transformer intended to transmit an information signal to protective and control devices
NOTE – The accuracy class of a protective current transformer is designated by its class index followed by the letter P (standing for "Protection"). The class index gives the limit of the absolute value of composite error at the rated accuracy limit primary current for the class concerned, as a percentage of this current.
[IEV number 321-02-19]FR
transformateur de courant pour protection
transformateur de courant destiné à transmettre un signal d'information à des dispositifs de protection ou de commande
NOTE – La classe de précision d'un transformateur de courant pour protection est désignée par son indice de classe, suivi de la lettre "P" (signifiant "Protection"). L'indice de classe indique la limite supérieure de la valeur absolue de l'erreur composée, au courant limite de précision assigné prescrit pour la classe considérée, en pourcentage de ce courant.
[IEV number 321-02-19]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > трансформатор тока для защиты
См. также в других словарях:
Value — Val ue, n. [OF. value, fr. valoir, p. p. valu, to be worth, fr. L. valere to be strong, to be worth. See {Valiant}.] 1. The property or aggregate properties of a thing by which it is rendered useful or desirable, or the degree of such property or … The Collaborative International Dictionary of English
Value received — Value Val ue, n. [OF. value, fr. valoir, p. p. valu, to be worth, fr. L. valere to be strong, to be worth. See {Valiant}.] 1. The property or aggregate properties of a thing by which it is rendered useful or desirable, or the degree of such… … The Collaborative International Dictionary of English
Value Place Simpsonville — (Simpsonville,США) Категория отеля: Адрес: 3025 Grandview Drive, Simpsonvi … Каталог отелей
value — The importance placed on something by an individual. Value is subjective and may change according to the circumstances. Something that may be valued highly at one time may be valued less at another time. The CENTER ONLINE Futures Glossary * * * ▪ … Financial and business terms
Value system — A value system is a set of consistent ethic values (more specifically the personal and cultural values) and measures used for the purpose of ethical or ideological integrity. A well defined value system is a moral code. Personal and communal One… … Wikipedia
Value of life — The value of life (or price of life) is an economic or moral value assigned to life in general, or to specific living organisms. In social and political sciences, it is the marginal cost of death prevention in a certain class of circumstances. As … Wikipedia
Value-added reseller — A value added reseller (VAR) is a company that adds some feature(s) to an existing product(s), then resells it (usually to end users) as an integrated product or complete turn key solution. This practice is common in the electronics industry,… … Wikipedia
Value at Risk — noun A widely used measure of the risk of loss on a specific portfolio of financial assets. For a given portfolio, probability and time horizon, VaR is a threshold value such that the probability that the mark to market loss on the portfolio over … Wiktionary
Value engineering — is a systematic method to improve the value of goods and services by using an examination of function. Value, as defined, is the ratio of function to cost. Value can therefore be increased by either improving the function or reducing the cost. It … Wikipedia
Value theory — encompasses a range of approaches to understanding how, why and to what degree people should value things; whether the thing is a person, idea, object, or anything else. This investigation began in ancient philosophy, where it is called axiology… … Wikipedia
Value at risk — (VaR) is a maximum tolerable loss that could occur with a given probability within a given period of time. VaR is a widely applied concept to measure and manage many types of risk, although it is most commonly used to measure and manage the… … Wikipedia
Перевод: с русского на немецкий
с немецкого на русский- С немецкого на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский