-
1 НКУ распределения и управления
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
Русско-французский словарь нормативно-технической терминологии > НКУ распределения и управления
-
2 энергия биомассы
энергия биомассы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biomass energy
A renewable energy source that makes use of such biofuels as methane (biogas) generated by sewage, farm, industrial, or household organic waste materials. Other biofuels include trees grown in so-called "energy forests" or other plants, such as sugar cane, grown for their energy potential. Biomass energy relies on combustion and therefore produces carbon dioxide; its use would not, therefore, alleviate the greenhouse effect. (Source: UVAROV)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > энергия биомассы
-
3 воздействующая величина электрического реле
- Grandeur d’alimentation
- grandeur d'alimentation
воздействующая величина электрического реле
Электрическая величина, которая одна или в сочетании с другими электрическими величинами должна быть приложена к электрическому реле в заданных условиях для достижения ожидаемого функционирования
[ ГОСТ 16022-83]EN
energizing quantity
an electrical quantity (either current or voltage) which alone, or in combination with other such quantities, applied to a relay under specified conditions enables it to fulfil its purpose
[IEV number 446-12-01]
energizing quantity (for elementary relays)electrical quantity which, when applied to the input circuit of an elementary relay under specified conditions, enables it to fulfill its purpose
NOTE – For elementary relays the energizing quantity is usually a voltage. Therefore, the input voltage as energizing quantity is used in the definitions given below. Where a relay is energized by a given current instead, the respective terms and definitions apply with "current" used instead of "voltage".
[IEV number 444-03-01]FR
grandeur d'alimentation
grandeur électrique, courant ou tension, qui, seule ou en combinaison avec d'autres grandeurs électriques, courant ou tension, doit être appliquée dans des conditions spécifiées à un relais pour en obtenir le comportement attendu
[IEV number 446-12-01]
grandeur d'alimentation (pour les relais élémentaires), f
grandeur électrique qui, appliquée au circuit d'entrée d'un relais élémentaire dans des conditions spécifiées, lui permet d'accomplir sa fonction
NOTE – Pour les relais élémentaires, la grandeur d'alimentation est en général une tension. En conséquence, on utilise la tension d'entrée comme grandeur d'alimentation dans les définitions données ci-dessous. Lorsqu'un relais est alimenté par un courant, les termes et définitions respectifs sont à utiliser avec le terme "courant" au lieu du terme "tension".
[IEV number 444-03-01]Тематики
Классификация
>>>EN
DE
FR
49. Воздействующая величина электрического реле
D. Eingangsgrösse
Е. Energizing quantity
F. Grandeur d’alimentation
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > воздействующая величина электрического реле
-
4 ждущий генератор развертки
<>ждущий генератор развертки
-
[IEV number 314-06-05]EN
triggered time base
time base which, for each sweep, is initiated by a trigger signal and, therefore, has a rest position
NOTE 1 – The duration of the sweep is not dependent on the period of the observed quantity.
NOTE 2 – The repetition rate is not necessarily periodic.
[IEV number 314-06-05]FR
base de temps déclenchée
base de temps pour laquelle, à chaque balayage, le fonctionnement est provoqué par un signal de déclenchement et qui possède, en conséquence, une position de repos
NOTE 1 – La durée du balayage ne dépend pas de la période de la grandeur observée.
NOTE 2 – La cadence de répétition n'est pas nécessairement périodique.
[IEV number 314-06-05]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ждущий генератор развертки
-
5 изомер
изомер
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
isomer
1) Two or more compounds having the same molecular formula, but a different arrangement of atoms within the molecule. 2) One of two or more chemical substances having the same elementary percentage composition and molecular weight but differing in structure, and therefore in properties; there are many ways in which such structural differences occur. (Source: CED / MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > изомер
-
6 интергармоника
интергармоника
Интергармониками называют токи (напряжения) частота которых не кратна частоте основной гармоники.EN
interharmonic component
sinusoidal component of a periodic quantity having a an interharmonic frequency
NOTE 1 For brevity, such a component may be referred to simply as an interharmonic.
NOTE 2 For practical analysis, an approximation of the periodicity may be necessary.
NOTE 3 The value is normally expressed as an r.m.s. value.
NOTE 4 As stated in IEC 61000-4-7, the time window has a width of 10 fundamental periods (50 Hz systems) or 12 fundamental periods (60 Hz systems), i.e. approximately 200 ms. The difference in frequency between two consecutive interharmonic components is, therefore, approximately 5 Hz. In the case of other fundamental frequencies, the time window should be selected between 6 fundamental periods (approximately 1 000 ms at 6 Hz) and 18 fundamental periods (approximately 100 ms at 180 Hz).
[IEC 60146-1-1, ed. 4.0 (2009-06)]FR
composante interharmonique
composante sinusoïdale d’une grandeur périodique dont la fréquence est une fréquence interharmonique
NOTE 1 Pour des raisons de concision, ce type de composante peut être désigné simplement par le terme « interharmonique ».
NOTE 2 Pour l’analyse pratique, il peut être nécessaire de procéder à une approximation de la périodicité.
NOTE 3 La valeur est normalement exprimée comme une valeur efficace.
NOTE 4 Comme indiqué dans la CEI 61000-4-7, la fenêtre temporelle a une largeur de 10 périodes fondamentales (systèmes de 50 Hz) ou de 12 périodes fondamentales (systèmes de 60 Hz), c’est-à-dire approximativement 200 ms. La différence de fréquence entre deux composantes interharmoniques consécutives est, par conséquent, d’environ 5 Hz. Dans le cas d’autres fréquences fondamentales, il convient de choisir la fenêtre temporelle entre 6 périodes fondamentales (environ 1 000 ms à 6 Hz) et 18 périodes fondamentales (environ 100 ms à 180 Hz). [IEC 60146-1-1, ed. 4.0 (2009-06)]
На частотах, расположенных между частотами гармонических составляющих тока и напряжения, могут наблюдаться интергармоники. Интергармоники могут возникать на дискретных частотах или иметь спектральные составляющие в достаточно широкой полосе частот. Суммарное воздействие различных источников интергармоник маловероятно и в настоящем стандарте не учитывается.
Полного понимания природы электромагнитных возмущений, ассоциирующихся с интергармониками, еще нет, и в настоящее время к этому явлению возник повышенный интерес. Интергармоники всегда присутствуют в системе электроснабжения, но в последнее время с резким увеличением силовых электронных систем их практическое влияние стало более ощутимым.
[Збигнев Ханзелка (Zbigniew Hanzelka), Анжей Бьень (Andrzej Bien) AGH-UST, Краков, Республика Польша. Энергосбережение №7/2005]Тематики
Действия
Синонимы
EN
FR
Русско-французский словарь нормативно-технической терминологии > интергармоника
-
7 невозобновляемый ресурс
невозобновляемый ресурс
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
non-renewable resource
A natural resource which, in terms of human time scales, is contained within the Earth in a fixed quantity and therefore can be used once only in the foreseeable future (although it may be recycled after its first use). This includes the fossil fuels and is extended to include mineral resources and sometimes ground water, although water and many minerals are renewed eventually. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > невозобновляемый ресурс
-
8 отвод газа из мусорной ямы
отвод газа из мусорной ямы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
landfill degasification
Landfill gas is highly dangerous as methane is highly explosive; therefore it must be controlled at all operational landfill sites, whether by active or passive ventilation or both especially in the case of deep sites. There exist venting systems for shallow and deep sites respectively. (Source: PORT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > отвод газа из мусорной ямы
-
9 охрана грунтовых вод
охрана грунтовых вод
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
water table protection
Water table is inherently susceptible to contamination from landuse activities. Remediation is very expensive and often impractical. Prevention of contamination is therefore critical in effective groundwater management. (Source: TECHBA)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > охрана грунтовых вод
-
10 параметры ответвлений
параметры ответвлений
Параметры, значения которых определяют режим любого ответвления обмотки, не являющегося основным.
К параметрам ответвлений обмотки относят:
- напряжение ответвления (по аналогии с номинальным напряжением по 3.4.3);
- мощность ответвления (по аналогии с номинальной мощностью по 3.4.6);
- ток ответвления (по аналогии с номинальным током по 3.4.7)
(МЭС 421-05-10).
Примечание — Параметры ответвлений устанавливают для любой обмотки трансформатора,
а не только для обмотки с ответвлениями (см. 5.2 и 5.3)
[ ГОСТ 30830-2002]EN
tapping quantities
those quantities the numerical values of which define the tapping duty.The tapping quantities include for each winding and for each tapping:
a) a tapping voltage,
b) a tapping power,
c) a tapping current
NOTE – Tapping quantities are related to a given tapping connection of the transformer and apply therefore to any winding, including any untapped winding
[IEV number 421-05-10]FR
grandeurs de prise
grandeurs dont les valeurs numériques définissent le régime de prise. Les grandeurs de prise comprennent pour chaque enroulement et pour chaque prise:
a) une tension de prise,
b) une puissance de prise,
c) un courant de prise
NOTE – Les grandeurs de prise sont rattachées à une connexion de prise donnée du transformateur et s'appliquent donc à tout enroulement, même s'il n'a pas de prises.
[IEV number 421-05-10]Тематики
Классификация
>>>EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > параметры ответвлений
-
11 полихлорированный бифенил
полихлорированный бифенил
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
polychlorinated biphenyl
PCBs are a family of chemical compounds which do not exist in nature but which are man-made. Commercial mixtures are clear, pale yellow liquids, manufactured by the replacement of hydrogen atoms on the biphenyl molecule by chlorine. Because of their physical properties, PCBs are commonly found in electrical equipment which requires dielectric fluid such as power transformers and capacitors, as well as in hydraulic machinery, vacuum pumps, compressors and heat-exchanger fluids. Other uses include: lubricants, fluorescent light ballasts, paints, glues, waxes, carbonless copy paper, inks including newspapers, dust-control agents for dirt roads, solvents for spreading insecticides, cutting oils. PCBs are stable compounds and although they are no longer manufactured they are extremely persistent and remain in huge quantities in the atmosphere and in landfill sites. They are not water-soluble and float on the surface of water where they are eaten by aquatic animals and so enter the food chain. PCBs are fat-soluble, and are therefore easy to take into the system, but difficult to excrete. (Source: PZ / PHC)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > полихлорированный бифенил
-
12 провинция
провинция
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
province
A geographic area of some considerable extent, smaller than a continent but larger than a region, which is unified by some or all of its characteristics and which can therefore be studied as a whole. A faunal province, for example, has a particular assemblage of animal species, which differs from assemblages in different contemporaneous environments elsewhere. (Source: WHIT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > провинция
-
13 производство цемента
производство цемента
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
cement manufacture
Cement is produced by heating a mixture of clay or shale plus chalk or lime in a rotary kiln up to 250 m long per 8 m diameter rotating at 1 rpm. The process can be wet, semi-dry or dry and the fuel can be pulverized coal, oil or gas. As the coal ash is similar in composition to the clay or shale, it can stay in the cement clinker. As one of the kiln operator's major costs is fuel and even a modest sized kiln can consume 8-10 tons of coal per hour, the cement kiln could, therefore, solve a disposal problem and also benefit the cement manufacturer by reducing fuel costs. (Source: PORT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > производство цемента
-
14 прямой пуск вращающегося электродвигателя
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Русско-французский словарь нормативно-технической терминологии > прямой пуск вращающегося электродвигателя
-
15 технология, приемлемая для местных условий
технология, приемлемая для местных условий
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
indigenous technology
Technologies employed by the native inhabitants of a country and which constitute an important part of its cultural heritage and should therefore be protected against exploitation by industrialized countries; the problem of indigenous knowledge has been discussed during the Rio Conference but it does not receive much protection under the Biodiversity Convention. Article 8 mandates that parties "respect, preserve and maintain knowledge, innovations and practices of indigenous and local communities embodying traditional life styles... and promote their wider application with the approval and involvement of holders of such knowledge, innovations and practices and encourage the equitable sharing of benefits arising from them". (Source: RRDA / WRES)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > технология, приемлемая для местных условий
-
16 ток замыкания на землю
ток замыкания на землю
Ток повреждения, проходящий в землю через место замыкания.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
ток замыкания на землю
Электрический ток, протекающий в Землю, открытую и стороннюю проводящие части и защитный проводник при повреждении изоляции токоведущей части.
Примечание – В Международном электротехническом словаре используют термин «ток повреждения на землю».
При повреждении изоляции токоведущей части резко уменьшается сопротивление между этой токоведущей частью, с одной стороны, и Землёй, открытыми, сторонними проводящими частями и защитными проводниками, с другой стороны. В результате этого резко увеличивается величина электрического тока, стекающего с токоведущей части в Землю, а также в проводящие части, соединённые защитными проводниками с заземляющим устройством электроустановки здания и с заземлённой токоведущей частью источника питания. Подобный электрический ток аварийного режима электроустановки здания в нормативной и правовой документации называют током замыкания на землю.
Путь, по которому может протекать ток замыкания на землю, зависит от типа заземления системы. Если произошло повреждение основной изоляции опасной токоведущей части электрооборудования класса I и возникло её замыкание на открытую проводящую часть, то в электроустановке здания, соответствующей типам заземления системы TT и IT, ток замыкания на землю через повреждённую изоляцию протекает из токоведущей части в открытую проводящую часть. Далее из открытой проводящей части по защитному проводнику, главной заземляющей шине, заземляющим проводникам и заземлителю электрический ток протекает в локальную землю. Если электроустановка здания соответствует типам заземления системы TN, преобладающая часть тока замыкания на землю протекает не в локальную землю, а по защитным проводникам и по PEN-проводникам электроустановки здания и низковольтной распределительной электрической сети протекает к заземлённой токоведущей части источника питания.
[] http://www.volt-m.ru/glossary/letter/%D2/view/81/EN
earth fault current
current flowing to earth due to an insulation fault
[IEV number 442-01-23]FR
courant de défaut à la terre
courant qui s'écoule à la terre lors d'un défaut d'isolement
[IEV number 442-01-23]Параллельные тексты EN-RU The earth fault current starts as a localized arc at the point where the insulation has failed; this arc is characterized by a rather modest current level of the order of tens of milliamps. Subsequently, the fault evolves, more or less rapidly, to become a true earth-phase fault. If not rapidly interrupted by protection devices, this fault may end up affecting all the phases, creating a three-phase shortcircuit with earth contact.
[ABB]Ток замыкания на землю возникает в зоне повреждения изоляции в виде локальной дуги. Эта дуга характеризуется относительно небольшим значением тока порядка десятков миллиампер. Со временем зона повреждения изоляции постепенно увеличивается, и образуется однофазное замыкание на землю. Если ток не будет своевременно отключен устройством защиты, то эта неисправность в итоге может затронуть все фазные проводники и привести к трехфазному короткому замыканию на землю.
[Перевод Интент]Therefore, the first consequence of the earth fault current is the damage caused to the plant, whether due to the modest initial arc currents which, because of the difficulty in detection by the overcurrent releases may continue for long periods of time and start a fire, or due to the shortcircuit that develops after the integrity of the entire plant has been jeopardized.
[ABB]Таким образом, ток замыкания на землю может повредить электроустановку. Сначала возникает электрическая дуга с небольшим током, который максимальный расцепитель тока обнаружить не в состоянии, вследствие чего этот ток может протекать длительное время и привести к пожару. Кроме того, может возникнуть короткое замыкание, способное полностью вывести электроустановку из строя.
[Перевод Интент]Another important consequence of the earth fault current involves the danger to persons caused by indirect contact, i.e. following the contact with exposed-conductive-parts that have been energized accidentally due to a decay in the insulation.
[ABB]Другим последствием тока замыкания на землю является опасность косвенного прикосновения, т. е. прикосновения человека к открытым проводящим частям, оказавшимся вследствие повреждения изоляции под напряжением.
[Перевод Интент]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ток замыкания на землю
-
17 топливо с низким октановым числом (низким содержанием свинца)
топливо с низким октановым числом (низким содержанием свинца)
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
unleaded petrol
Petrol with a low octane rating, which has no lead additives in it and therefore creates less lead pollution in the atmosphere. (Source: PHC)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > топливо с низким октановым числом (низким содержанием свинца)
-
18 трансформаторный мост
трансформаторный мост
-
[IEV number 313-08-03]EN
transformer bridge
alternating current measuring bridge intended to measure impedances, in which at least two arms consist of tapped windings on a transformer, making use of the known ratios of the turns and which can therefore have fixed-value standards
[IEV number 313-08-03]FR
pont à transformateur
pont de mesure à courant alternatif destiné à mesurer une impédance, dont au moins deux bras sont constitués par les enroulements à prises d'un transformateur, faisant usage des rapports connus des nombres de spires et pouvant ainsi comporter des étalons à valeur fixe
[IEV number 313-08-03]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > трансформаторный мост
-
19 химическая инерция
химическая инерция
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
persistence
The capacity of a substance to remain chemically stable. This is an important factor in estimating the environmental effects of substances discharged into the environment. Certain toxic substances (e.g., cyanides) have a low persistence, whereas other less immediately toxic substances (e.g., many organochlorines) have a high persistence and may therefore produce more serious effects. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > химическая инерция
-
20 хлорфторуглероды
хлорфторуглероды
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
chlorofluorocarbon
Gases formed of chlorine, fluorine, and carbon whose molecules normally do not react with other substances; they are therefore used as spray can propellants because they do not alter the material being sprayed. (Source: LANDY)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > хлорфторуглероды
- 1
- 2
См. также в других словарях:
therefore — 1. This is the most resilient of the adverbs in there and has been part of the core language since the 12c. It is always pronounced with the stress on the first syllable, and can be placed in various positions in a sentence, including the… … Modern English usage
therefore — therefore, hence, consequently, then, accordingly, so are adverbs used as connectives to indicate logical or causal sequence. They vary in the degree of closeness of connection suggested as well as in the kind of sequence implied. Therefore and… … New Dictionary of Synonyms
Therefore — There fore, conj. & adv. [OE. therfore. See {There}, and {Fore}, adv., {For}, and cf. {Therefor}.] 1. For that or this reason, referring to something previously stated; for that. [1913 Webster] I have married a wife, and therefore I can not come … The Collaborative International Dictionary of English
therefore — O.E. þærfore; from THERE (Cf. there) + fore, Old English and Middle English collateral form of FOR (Cf. for). Since c.1800, therefor has been used in sense of for that, by reason of that; and therefore in sense of in consequence of that … Etymology dictionary
therefore — index consequently Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
therefore — [adv] as a result; for that reason accordingly, and so, consequently, ergo, for, forasmuch as, for this reason, hence, inasmuch as, in consequence, in that event, on account of, on the grounds, since, so, then, thence, therefrom, thereupon, thus … New thesaurus
therefore — ► ADVERB ▪ for that reason; consequently … English terms dictionary
therefore — [ther′fôr΄] adv. [ME ther fore: see THERE & FORE] as a result of this or that; for this or that reason; consequently; hence: often used as a conjunctive adverb … English World dictionary
therefore — 01. The accused murderer was found not guilty because the judge said that he was mentally ill, and [therefore] couldn t be held responsible for his actions. 02. Research has shown that bright yellow and bright blue are the most visible, and… … Grammatical examples in English
therefore — there|fore [ ðerfɔr ] adverb FORMAL *** Therefore is used as a way of showing how a sentence or clause is related to what has already been said. as a result of the reason that has just been mentioned: The new boots are lighter and softer, and… … Usage of the words and phrases in modern English
therefore */*/*/ — UK [ˈðeə(r)fɔː(r)] / US [ˈðerfɔr] adverb Summary: Therefore is used as a way of showing how a sentence or clause is related to what has already been said. as a result of the reason that has just been mentioned The new boots are lighter and softer … English dictionary