-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
2 каталитический конвертер
каталитический конвертер
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
catalytic converter
Catalytic converters are designed to clean up the exhaust fumes from petrol-driven vehicles, which are otherwise the major threat to air quality standards in congested urban streets and on motorways. Converters remove carbon monoxide, the unburned hydrocarbons and the oxides of nitrogen. These compounds are damaging to human health and the environment in a variety of ways. The converter is attached to the vehicle' s exhaust near the engine. Exhaust gases pass through the cellular ceramic substrate, a honeycomb-like filter. While compact, the intricate honeycomb structure provides a surface area of 23.000 square metres. This is coated with a thin layer of platinum, palladium and rhodium metals, which act as catalysts that simulate a reaction to changes in the chemical composition of the gases. Platinum and palladium convert hydrocarbons and carbon monoxide into carbon dioxide and water vapour. Rhodium changes nitrogen oxides and hydrocarbons into nitrogen and water, which are harmless. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > каталитический конвертер
-
3 загрязнение (в электробезопасности)
загрязнение
Присутствие инородного вещества: твердого, жидкого или газообразного (ионизированные газы), - которое может вызвать уменьшение диэлектрической прочности или поверхностного сопротивления.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
загрязнение
Любое добавление инородных веществ, твердых, жидких или газообразных (ионизированных газов), которые могли бы уменьшить электрическую прочность изоляции или удельное сопротивление поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
pollution
any condition of foreign matter, solid, liquid or gaseous (ionized gases), that may affect dielectric strength or surface resistivity
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
any addition of foreign matter, solid, liquid or gaseous that can produce a permanent reduction of dielectric strength or surface resistivity of the insulation
NOTE – Ionized gases of a temporary nature are not considered as to be a pollution.
[IEV number 442-01-28]
contamination
the first is defined as area and the second as particulate. The first is caused by surface contaminants that cannot be removed by cleaning or are stained after cleaning. Those may be foreign matter on the surface of, for example a localized area that is smudged, stained, discoloured, mottled, etc., or large areas exhibiting a hazy or cloudy appearance resulting from a film of foreign materials
[IEC 62276, ed. 1.0 (2005-05)]FR
pollution
tout apport de matériau étranger solide, liquide ou gazeux (gaz ionisés) qui peut entraîner une réduction de la rigidité diélectrique ou de la résistivité de la surface
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
tout apport de matériau étranger solide, liquide ou gazeux qui peut entraîner une réduction permanente de la rigidité diélectrique ou de la résistivité de surface de l'isolation
NOTE – Les gaz ionisés de nature fugace ne sont pas considérés comme une pollution.
[IEV number 442-01-28]
Тематики
Обобщающие термины
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > загрязнение (в электробезопасности)
-
4 напряжение поверхности
напряжение поверхности
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
surface tension
The force acting on the surface of a liquid, tending to minimize the area of the surface; quantitatively, the force that appears to act across a line of unit length on the surface. Also known as interfacial force; interfacial tension; surface intensity. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > напряжение поверхности
-
5 плоский источник загрязнения атмосферы
плоский источник загрязнения атмосферы
плоский источник
Источник, выбрасывающий загрязняющие атмосферу вещества с установленной поверхности
[ ГОСТ 17.2.1.04-77]Тематики
Синонимы
EN
DE
FR
24ж. Плоский источник загрязнения атмосферы
Плоский источник
D. Flachenformige Luftverunreinigungsquelle
Е. Area source of air pollution
F. Source de surface
Источник, выбрасывающий загрязняющие атмосферу вещества с установленной поверхности
Источник: ГОСТ 17.2.1.04-77: Охрана природы. Атмосфера. Источники и метеорологические факторы загрязнения, промышленные выбросы. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > плоский источник загрязнения атмосферы
-
6 площадь жилая
площадь жилая
Сумма площадей всех жилых помещений в квартире, общежитии или гостинице
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > площадь жилая
-
7 площадь подсобная
площадь подсобная
Сумма площадей подсобных помещений в квартире - санузлов, кухонь, коридоров
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > площадь подсобная
-
8 биогеографический регион
биогеографический регион
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biogeographical region
Area of the Earth's surface defined by the species of fauna and flora it contains. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > биогеографический регион
-
9 гора
гора
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
mountain
A feature of the earth's surface that rises high above the base and has generally steep slopes and a relatively small summit area. Mountains are an important source of water, energy, minerals, forest and agricultural products, and recreation. They are storehouses of biological diversity and endangered species and an essential part of the global ecosystem. About 10% of the world's population depend on mountain resources and nearly half of these people are affected by the degradation of mountain watershed areas. (Source: MGH / WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > гора
-
10 действующая площадь водосбора
действующая площадь водосбора
Часть площади водосбора, с которой осуществляется сток при данном слое осадков, поступающих на поверхность водосбора.
[ ГОСТ 19179-73]Тематики
Обобщающие термины
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > действующая площадь водосбора
-
11 законодательство в области сохранения почв
законодательство в области сохранения почв
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
soil conservation legislation
A binding rule or body of rules prescribed by a government to protect and prevent the loss of an area's surface layer of decomposed rock and organic material, valued for its nutrients and ability to support life. (Source: DES)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > законодательство в области сохранения почв
-
12 зона контакта шины с дорогой
зона контакта шины с дорогой
контакт шины с дорогой
Совокупность участков контакта, образованных наружными поверхностями выступов рисунка протектора с опорной поверхностью, и промежутков между ними.
[ ГОСТ 22374-77]Тематики
Обобщающие термины
Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > зона контакта шины с дорогой
-
13 контурная площадь контакта
контурная площадь контакта
Fк
Площадь, ограниченная внешней огибающей участков контакта, образованных наружными поверхностями выступов рисунка протектора с опорной поверхностью.
[ ГОСТ 17697-72]
[ ГОСТ 22374-77]Тематики
- автомобили, качение колеса
- шины пневматические
Обобщающие термины
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > контурная площадь контакта
-
14 коэффициент насыщенности контакта
коэффициент насыщенности контакта
Kн
Отношение площади контакта по выступам рисунка протектора к контурной площади контакта:
[ ГОСТ 17697-72]
[ ГОСТ 22374-77]Тематики
- автомобили, качение колеса
- шины пневматические
Обобщающие термины
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент насыщенности контакта
-
15 коэффициент насыщенности рисунка протектора
коэффициент насыщенности рисунка протектора
Отношение площади выступа рисунка беговой дорожки протектора к ее общей площади.
[ ГОСТ 22374-77]Тематики
Обобщающие термины
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > коэффициент насыщенности рисунка протектора
-
16 норма жилищной обеспеченности
норма жилищной обеспеченности
Количество полезной площади в жилых зданиях, установленное на определённый период времени на одного человека
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
- occupant load rate (area of floor per person established by building by-laws)
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > норма жилищной обеспеченности
-
17 озерный бассейн
озерный бассейн
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
lake basin
1) The depression in the Earth's surface occupied or formerly occupied by a lake and containing its shore features. 2) The area from which a lake receives drainage. (Source: BJGEO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > озерный бассейн
-
18 плотная бумага
плотная бумага
Бумага с сомкнутой поверхностью и уплотненной структурой.
[ ГОСТ 17586-80]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > плотная бумага
-
19 площадь застройки
площадь застройки
Площадь горизонтального сечения по внешнему обводу здания на уровне цоколя, включая выступающие части, имеющие перекрытия - веранды, портики, галереи
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > площадь застройки
-
20 площадь конструктивная
площадь конструктивная
Суммарная площадь горизонтальных сечений вертикальных конструкций
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > площадь конструктивная
- 1
- 2
См. также в других словарях:
Surface area — is the measure of how much exposed area an object has. It is expressed in square units. If an object has flat faces, its surface area can be calculated by adding together the areas of its faces. Even objects with smooth surfaces, such as spheres … Wikipedia
surface area — surface ,area noun count the total area of a surface or surfaces, especially the outside surfaces of an object: enough paint to cover a surface area of 900 square feet … Usage of the words and phrases in modern English
surface area — surface .area n the area of the outside of an object that can be measured … Dictionary of contemporary English
surface area — noun the extent of a 2 dimensional surface enclosed within a boundary (Freq. 2) the area of a rectangle it was about 500 square feet in area • Syn: ↑area, ↑expanse • Derivationally related forms: ↑areal ( … Useful english dictionary
surface area — UK / US noun [countable] Word forms surface area : singular surface area plural surface areas maths the total area of a surface or surfaces, especially the outside surfaces of an object enough paint to cover a surface area of 900 square feet … English dictionary
surface area — paviršiaus plotas statusas T sritis Standartizacija ir metrologija apibrėžtis Nagrinėjamojo paviršiaus plotas. atitikmenys: angl. surface area vok. Oberflächeninhalt, m rus. площадь поверхности, f pranc. aire de surface, f … Penkiakalbis aiškinamasis metrologijos terminų žodynas
surface area — paviršiaus plotas statusas T sritis fizika atitikmenys: angl. surface area vok. Oberflächeninhalt, m rus. площадь поверхности, f pranc. aire de surface, f … Fizikos terminų žodynas
surface pressure-surface area isotherm — Surface Pressure Surface Area Isotherm Изотерма поверхностное давление площадь Зависимость поверхностного давления монослоя Ленгмюра на поверхности водной субфазы от площади, занимаемой молекулами поверхностно активного вещества в этом… … Толковый англо-русский словарь по нанотехнологии. - М.
Surface area to volume ratio — In chemical reactions involving a solid material, the surface area to volume ratio is an important factor for the reactivity, that is, the rate at which the chemical reaction will proceed. In some industries it is abbreviated sa/vol.Physical… … Wikipedia
Surface area, volume, and average depth of oceans and seas — ▪ Table Surface area, volume, and average depth of oceans and seas area volume average depth 000,000 sq km 000,000 sq mi 000,000 cu km 000,000 cu mi m ft Atlantic Ocean without marginal seas 82.440 31.830 324.600 77.900 3,930 12,890 with… … Universalium
surface area — noun The total area on the surface of a three dimensional figure … Wiktionary