-
1 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
-
2 обслуживание техническое
техническое обслуживание
Совокупность действий, выполняемых для сохранения или восстановления состояния изделия, в котором оно способно отвечать требованиям соответствующих технических условий и выполнять необходимые функции.
[ ГОСТ Р МЭК 60050-426-2006]
техническое обслуживание
Текущие действия, выполняемые для сохранения в полной мере работоспособного состояния установленного электрооборудования.
[ ГОСТ Р МЭК 60050-426-2006]
техническое обслуживание
Комплекс операций и/или организационных действий, направленных на поддержание объекта в состоянии или возвращение объекта в состояние, в котором он способен выполнять требуемую функцию.
[ОСТ 45.152-99 ]
обслуживание техническое
Комплекс работ для поддержания исправности или работоспособности машин и оборудования при их эксплуатации, хранении и транспортировании
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
maintenance
1. All action taken to retain materiel in or to restore it to a specified condition. It includes: inspection, testing, servicing, classification as to serviceability, repair, rebuilding, and reclamation.
2. All supply and repair action taken to keep a force in condition to carry out its mission.
3. The routine recurring work required to keep a facility (plant, building, structure, ground facility, utility system, or other real property) in such condition that it may be continuously utilized, at its original or designed capacity and efficiency, for its intended purpose.[Dictionary of Military and Associated Terms. US Department of Defense 2005]Тематики
- тех. обсл. и ремонт средств электросвязи
Синонимы
- ТО
EN
- backup
- concept maintenance
- engineering service
- machine servicing
- maintenance
- maintenance service
- maintenance support
- maintenance work
- maintenance works
- mechanical services
- servicing
- technical maintenance
DE
FR
Русско-французский словарь нормативно-технической терминологии > обслуживание техническое
3 силовая цепь
силовая цепь
Цепь, передающая энергию от сети к элементам оборудования, используемым для выполнения производственных операций, а также к трансформаторам, питающим цепи управления.
[ГОСТ ЕН 1070-2003]
силовая цепь
Цепь, передающая энергию от сети к элементам оборудования, используемым непосредственно для выполнения производственных операций, а также к трансформаторам, питающим цепи управления.
[ ГОСТ Р МЭК 60204-1-2007]
силовая электрическая цепь
Электрическая цепь, содержащая элементы, функциональное назначение которых состоит в производстве или передаче основной части электрической энергии, ее распределении, преобразовании в другой вид энергии или в электрическую энергию с другими значениями параметров.
[ ГОСТ 18311-80]EN
power circuit
circuit that supplies power from the supply network to units of equipment used for productive operation and to transformers supplying control circuits
[IEC 60204-32, ed. 2.0 (2008-03)]FR
circuit de puissance
circuit qui transmet l'énergie du réseau aux éléments d'équipement utilisés directement pour le travail effectué par la machine et aux transformateurs alimentant les circuits de commande
[IEC 60204-32, ed. 2.0 (2008-03)]1 - Силовая цепь электродвигателя
2 - Цепь управления электродвигателемLS Tri-MEC vacuum contactors are mainly used for the switching of motors, transformers, capacitors in AC power lines.
[LS Industrial Systems]Вакуумные контакторы LS Tri-MEC предназначены в основном для коммутации силовых цепей переменного тока электродвигателей, трансформаторов, конденсаторов.
[Перевод Интент]Тематики
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > силовая цепь
См. также в других словарях:
machine tool — machine tooled, adj. a power operated machine, as a lathe, used for general cutting and shaping of metal and other substances. [1860 65] * * * Stationary, power driven machine used to cut, shape, or form materials such as metal and wood. Machine… … Universalium
Machine embroidery — is a term that can be used to describe two different actions. The first is using a sewing machine to manually create (either freehand or with built in stitches) a design on a piece of fabric or other similar item. The second is to use a specially … Wikipedia
Machine to Machine — M2M refers to data communications between machines. M2M is most commonly translated as Machine to Machine but has sometimes been translated as Man to Machine, Machine to Man, Machine to Mobile and Mobile to Machine. Among cellular telephone… … Wikipedia
machine gun — a small arm operated by a mechanism, able to deliver a rapid and continuous fire of bullets as long as the trigger is pressed. [1865 70] * * * Automatic weapon capable of rapid, sustained fire, usually 500–1,000 rounds per minute. Developed in… … Universalium
Machine de Marly — The Machine de Marly painted by Alfred Sisley The Machine de Marly, also widely known as La Machine de Marly and The Machine of Marly, was a French engineering marvel (though Arnold de Ville and Rennequin Sualem would be Belgians, by current… … Wikipedia
Machine Check Exception — A Machine Check Exception (MCE) is a type of computer hardware error that occurs when a computer s central processing unit detects a hardware problem. Microsoft Windows displays the error using the blue screen of death containing the error… … Wikipedia
machine room — noun a) A limited access room in a larger building dedicated to HVAC equipment and other machinery. b) A dedicated room for computers and related data processing equipment, often having a raised floor, abundant and dedicated air conditioning, and … Wiktionary
Uninterruptible power supply — A small free standing UPS … Wikipedia
Counter machine models — This page supplements counter machine. Although some authors use the name register machine synonymously with counter machine , this article will give details and examples of only of the most primitive species the counter machine of the genus… … Wikipedia
Welding power supply — A welding power supply is a device that provides an electric current to perform welding. Welding usually requires high current (over 80 amperes) and it can need above 12,000 amps in spot welding. Low current can also be used; welding two razor… … Wikipedia
Washing machine — This article is about the laundry cleaning apparatus. For the Sonic Youth album, see Washing Machine (album). A typical modern front loading washing machine Irreler Bauerntradition shows an early Miele was … Wikipedia
Перевод: с русского на французский
с французского на русский- С французского на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский