-
21 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
22 пусковой ток
пусковой ток
-EN
inrush current
transient current associated with energizing of transformers, cables, reactors, etc
[IEV number 448-11-30]
inrush current
Iin
current occurring during the transient period from the moment of switching to the steady-state condition
[IEC 60738-1, ed. 3.0 (2006-04)]
starting current
the steady-state r.m.s. current taken from the line over the starting period from zero speed to load speed with rated voltage and frequency applied
[IEV number 411-48-18]FR
courant d'appel
courant transitoire associé à la mise sous tension des transformateurs, câbles, bobines d'inductance, etc
[IEV number 448-11-30]
courant de démarrage
valeur efficace du courant en régime établi, absorbé par le moteur pendant la période de démarrage de la vitesse nulle jusqu'à la vitesse de charge minimale lorsqu'il est alimenté à la tension et à la fréquence assignées
[IEV number 411-48-18]Тематики
- машины электрические вращающиеся в целом
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > пусковой ток
-
23 реактивное сопротивление нулевой последовательности
реактивное сопротивление нулевой последовательности
-EN
zero sequence reactance
the quotient of the reactive fundamental component of zero sequence armature voltage, due to the presence of fundamental zero sequence armature current at rated frequency, by the value of that component of current, the machine running at rated speed
[IEV ref 411-50-16]FR
réactance homopolaire
quotient du terme fondamental de la composante réactive de la tension d'induit homopolaire, due à la présence du terme fondamental du courant d'induit homopolaire à fréquence assignée, par cette composante du courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-16]Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > реактивное сопротивление нулевой последовательности
-
24 реактивное сопротивление обратной последовательности
реактивное сопротивление обратной последовательности
-EN
negative sequence reactance
the quotient of the reactive fundamental component of negative sequence armature voltage, due to the sinusoidal negative sequence armature current at rated frequency, by the value of that component of current, the machine running at rated speed
[IEV ref 411-50-15]FR
réactance inverse
quotient du terme fondamental de la composante réactive de la tension d'induit inverse, due à la composante inverse du courant d'induit sinusoïdal à fréquence assignée, par la valeur de ce courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-15]Тематики
- электротехника, основные понятия
EN
- negative phase-sequence reactance
- negative sequence reactance
- subtransient reactance of negative phase
DE
FR
Русско-французский словарь нормативно-технической терминологии > реактивное сопротивление обратной последовательности
-
25 реактивное сопротивление прямой последовательности
реактивное сопротивление прямой последовательности
-EN
positive sequence reactance
the quotient of the reactive fundamental component of the positive sequence armature voltage, due to the sinusoidal positive sequence armature current at rated frequency, by the value of that component of current, the machine running at rated speed
[IEV ref 411-50-14]FR
réactance directe
quotient du terme fondamental de la composante réactive de la tension d'induit directe, due à la composante directe du courant d'induit sinusoïdal à fréquence assignée, par la valeur de ce courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-14]
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > реактивное сопротивление прямой последовательности
-
26 трансформатор тока для защиты
трансформатор тока для защиты
Трансформатор тока, предназначенный для передачи сигнала измерительной информации на устройства защиты и управления.
[ ГОСТ 18685-73]EN
protective current transformer
a current transformer intended to transmit an information signal to protective and control devices
NOTE – The accuracy class of a protective current transformer is designated by its class index followed by the letter P (standing for "Protection"). The class index gives the limit of the absolute value of composite error at the rated accuracy limit primary current for the class concerned, as a percentage of this current.
[IEV number 321-02-19]FR
transformateur de courant pour protection
transformateur de courant destiné à transmettre un signal d'information à des dispositifs de protection ou de commande
NOTE – La classe de précision d'un transformateur de courant pour protection est désignée par son indice de classe, suivi de la lettre "P" (signifiant "Protection"). L'indice de classe indique la limite supérieure de la valeur absolue de l'erreur composée, au courant limite de précision assigné prescrit pour la classe considérée, en pourcentage de ce courant.
[IEV number 321-02-19]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > трансформатор тока для защиты
-
27 ток намагничивания трансформатора тока
ток намагничивания трансформатора тока
Действующее значение тока, потребляемого вторичной обмоткой трансформатора тока, когда ко вторичным зажимам подведено синусоидальное напряжение номинальной частоты, причем первичная обмотка и все остальные обмотки разомкнуты.
[ ГОСТ 18685-73]EN
exciting current
the r.m.s. value of the current taken by the secondary winding of a current transformer, when a sinusoidal voltage of rated frequency is applied to the secondary terminals, the primary and any other windings being open-circuited
[IEV number 321-02-32]FR
courant d'excitation
valeur efficace du courant qui traverse l'enroulement secondaire d'un transformateur de courant, lorsqu'on applique entre les bornes secondaires une tension sinusoïdale à la fréquence assignée, l'enroulement primaire et tous les autres enroulements étant à circuit ouvert
[IEV number 321-02-32]Недопустимые, нерекомендуемые
EN
DE
- Erregerstrom, sekundärer
- sekundärer Erregerstrom
FR
Русско-французский словарь нормативно-технической терминологии > ток намагничивания трансформатора тока
-
28 токовая погрешность трансформатора тока
токовая погрешность трансформатора тока
Погрешность, которую трансформатор тока вносит в измерение тока, возникающая вследствие того, что действительный коэффициент трансформации не равен номинальному.
Примечание. Токовая погрешность определяется как арифметическая разность между действительным вторичным током и приведенным ко вторичной цепи действительным первичным током, выраженная в процентах приведенного ко вторичной цепи действительного первичного тока.
[ ГОСТ 18685-73]EN
current error
the error which a current transformer introduces into the measurement of a current and which arises from the fact that the actual transformation ratio is not equal to the rated transformation ratio
[IEV number 321-01-21]FR
erreur de courant
erreur de rapport (d'un transformateur de courant)
erreur qu'un transformateur de courant introduit dans la mesure d'un courant et qui provient de ce que le rapport de transformation n'est pas égal au rapport de transformation assigné
[IEV number 321-01-21]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > токовая погрешность трансформатора тока
-
29 синхронное реактивное сопротивление по продольной оси
синхронное реактивное сопротивление по продольной оси
-EN
direct-axis synchronous reactance
the quotient of the sustained value of that fundamental a.c. component of armature voltage, which is produced by the total direct-axis primary flux due to direct-axis armature current, and the value of the fundamental a.c. component of this current, the machine running at rated speed
[IEV ref 411-50-07]FR
réactance synchrone longitudinale
quotient de la valeur, en régime établi, du terme fondamental de la composante de la tension d'induit produite par le flux longitudinal total dû au courant d'induit longitudinal, par la valeur du terme fondamental de ce courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-07]
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > синхронное реактивное сопротивление по продольной оси
-
30 характеристика I2t автоматического выключателя
- caractéristique I2t d’un disjoncteur
характеристика I2t автоматического выключателя
Информация (как правило, в виде кривой), представленная максимальными, по времени отключения, значениями I2t как функция ожидаемого тока (действующее значение симметричной составляющей для переменного тока) от пикового значения ожидаемого тока, удовлетворяющего номинальной отключающей способности при коротком замыкании и соответствующем напряжении.
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]
характеристика I2t выключателя
Кривая, отражающая максимальные значения I2t как функцию ожидаемого тока в указанных условиях эксплуатации.
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
I2t characteristic of a circuit-breaker
information (usually a curve) giving the maximum values of I2t related to break time as a function of prospective current (r.m.s. symmetrical for a.c.) up to the maximum prospective current corresponding to the rated short-circuit breaking capacity and associated voltage
[IEC 60947-2, ed. 4.0 (2006-05)]FR
caractéristique I2t d’un disjoncteur
information (généralement une courbe) donnant les valeurs maximales de I2t correspondant à la durée de coupure en fonction du courant présumé (valeur efficace de la composante périodique en courant alternatif) jusqu’à la valeur maximale du courant présumé correspondant au pouvoir assigné de coupure en court-circuit à la tension correspondante
[IEC 60947-2, ed. 4.0 (2006-05)]Тематики
EN
FR
- caractéristique I2t d’un disjoncteur
Русско-французский словарь нормативно-технической терминологии > характеристика I2t автоматического выключателя
-
31 асинхронное реактивное сопротивление
асинхронное реактивное сопротивление
-EN
asynchronous reactance
the quotient of the reactive component of the average voltage at rated frequency, assumed to be sinusoidal and balanced, applied to the armature winding of a machine rotating out of synchronism, and the average current component at the same frequency
[IEV ref 411-50-05]FR
réactance asynchrone
quotient de la composante réactive de la tension moyenne à la fréquence assignée, supposée sinusoïdale et symétrique, appliquée à l'enroulement d'induit d'une machine tournant hors synchronisme, par la composante du courant moyen à la même fréquence
[IEV ref 411-50-05]Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > асинхронное реактивное сопротивление
-
32 кратковременная выдержка
кратковременная выдержка
EN
short-time delay
any intentional delay in operation within the limits of the rated short-time withstand current
[IEC 60947-1, ed. 5.0 (2007-06)]FR
retard de courte durée
tout retard intentionnel de manœuvre n'excédant pas les limites du courant assigné de courte durée admissible
[IEC 60947-1, ed. 5.0 (2007-06)]Тематики
- электротехника, основные понятия
EN
FR
Русско-французский словарь нормативно-технической терминологии > кратковременная выдержка
-
33 распределительный щит
- tableau de répartition, m
- tableau de distribution
распределительный щит
Комплектное устройство, содержащее различную коммутационную аппаратуру, соединенное с одной или более отходящими электрическими цепями, питающееся от одной или более входящих цепей, вместе с зажимами для присоединения нейтральных и защитных проводников.
[ ГОСТ Р МЭК 60050-826-2009]
щит распределительный
Электротехническое устройство, объединяющее коммутационную, регулирующую и защитную аппаратуру, а также контрольно-измерительные и сигнальные приборы
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
распределительный щит
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]EN
distribution board
assembly containing different types of switchgear and controlgear associated with one or more outgoing electric circuits fed from one or more incoming electric circuits, together with terminals for the neutral and protective conductors.
[IEV number 826-16-08]FR
tableau de répartition, m
ensemble comportant différents types d'appareillage associés à un ou plusieurs circuits électriques de départ alimentés par un ou plusieurs circuits électriques d'arrivée, ainsi que des bornes pour les conducteurs neutre et de protection.
[IEV number 826-16-08]Distribution switchboards, including the Main LV Switchboard (MLVS), are critical to the dependability of an electrical installation. They must comply with well-defined standards governing the design and construction of LV switchgear assemblies
A distribution switchboard is the point at which an incoming-power supply divides into separate circuits, each of which is controlled and protected by the fuses or switchgear of the switchboard. A distribution switchboard is divided into a number of functional units, each comprising all the electrical and mechanical elements that contribute to the fulfilment of a given function. It represents a key link in the dependability chain.
Consequently, the type of distribution switchboard must be perfectly adapted to its application. Its design and construction must comply with applicable standards and working practises.
[Schneider Electric]Распределительные щиты, включая главный распределительный щит низкого напряжения (ГРЩ), играют решающую роль в обеспечении надежности электроустановки. Они должны отвечать требованиям соответствующих стандартов, определяющих конструкцию и порядок изготовления НКУ распределения электроэнергии.
В распределительном щите выполняется прием электроэнергии и ее распределение по отдельным цепям, каждая из которых контролируется и защищается плавкими предохранителями или автоматическими выключателями.
Распределительный щит состоит из функциональных блоков, включающих в себя все электрические и механические элементы, необходимые для выполнения требуемой функции. Распределительный щит представляет собой ключевое звено в цепи обеспечения надежности.
Тип распределительного щита должен соответствовать области применения. Конструкция и изготовление распределительного щита должны удовлетворять требованиям применимых стандартов и учитывать накопленную практику применения.
[Перевод Интент]Рис. Schneider Electric
With Prisma Plus G you can be sure to build 100% Schneider Electric switchboards that are safe, optimised:
> All components (switchgear, distribution blocks, prefabricated connections, etc.) are perfectly rated and coordinated to work together;
> All switchboard configurations, even the most demanding ones, have been tested.
You can prove that your switchboard meets the current standards, at any time.
You can be sure to build a reliable electrical installation and give your customers full satisfaction in terms of dependability and safety for people and the installation.
Prisma Plus G with its discreet design, blends harmoniously into all tertiary and industrial buildings, including in entrance halls and passageways.
With Prisma Plus G you can build just the right switchboard for your customer, sized precisely to fit costs and needs.
With this complete, prefabricated and tested system, it's easy to upgrade your installation and still maintain the performance levels.
> The wall-mounted and floor-standing enclosures combine easily with switchboards already in service.
> Devices can be replaced or added at any time.
[Schneider Electric]С помощью оболочек Prisma Plus G можно создавать безопасные распределительные щиты, на 100 % состоящие из изделий Schneider Electric:
> все изделия (коммутационная аппаратура, распределительные блоки, готовые заводские соединения и т. д.) полностью совместимы механически и электрически;
> все варианты компоновки распределительных щитов, в том числе для наиболее ответственных применений, прошли испытания.В любое время вы можете доказать, что ваши распределительные щиты полностью соответствуют требованиям действующих стандартов.
Вы можете быть полностью уверены в том, что создаете надежные электроустановки, удовлетворяющие всем требованиям безопасности для людей и оборудования
Благодаря строгому дизайну, распределительные щиты Prisma Plus G гармонично сочетаются с интерьером любого общественного или промышленного здания. Они хорошо смотрятся и в вестибюле, и в коридоре.
Применяя оболочки Prisma Plus G можно создавать распределительные щиты, точно соответствующие требованиям заказчика как с точки зрения технических характеристик, так и стоимости.
С помощью данной испытанной системы, содержащей все необходимые компоненты заводского изготовления можно легко модернизировать существующую электроустановку и поддерживать её уровни производительности.> Навесные и напольные оболочки можно легко присоединить к уже эксплуатируемым распределительным щитам.
> Аппаратуру можно заменять или добавлять в любое время.
[Перевод Интент]The switchboard, central to the electrical installation.
Both the point of arrival of energy and a device for distribution to the site applications, the LV switchboard is the intelligence of the system, central to the electrical installation.
[Schneider Electric]Распределительный щит – «сердце» электроустановки.
Низковольтное комплектное устройство распределения является «сердцем» электроустановки, поскольку именно оно принимает электроэнергию из сети и распределяет её по территориально распределенным нагрузкам.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
- электроснабжение в целом
EN
- branch distribution panel
- distributing board
- distributing panel
- distributing switchboard
- distribution bench
- distribution board
- distribution panel
- distribution switchboard
- gear
- keyboard
- PNL
- SB
- sw & d
- switchboard
- switchboard panel
DE
- elektrischer Verteiler, m
- Schalttafel
- Verteiler, m
FR
- tableau de distribution
- tableau de répartition, m
Русско-французский словарь нормативно-технической терминологии > распределительный щит
-
34 сверхпереходное реактивное сопротивление по поперечной оси
сверхпереходное реактивное сопротивление по поперечной оси
-EN
quadrature-axis sub-transient reactance
the quotient of the initial value of a sudden change in that fundamental a.c. component of armature voltage, which is produced by the total quadrature-axis primary flux and the value of the simultaneous change in fundamental a.c. component of quadrature-axis armature current, the machine running at rated speed
[IEV ref 411-50-12]FR
réactance subtransitoire transversale
quotient de la valeur initiale d'une variation brusque du terme fondamental de la composante de la tension d'induit, produite par le flux transversal total, par la valeur de la variation simultanée du terme fondamental de la composante du courant d'induit transversal, la machine tournant à sa vitesse assignée
[IEV ref 411-50-12]Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > сверхпереходное реактивное сопротивление по поперечной оси
- 1
- 2
См. также в других словарях:
rated current — vardinė srovė statusas T sritis automatika atitikmenys: angl. current rating; nominal current; rated current vok. Nennstrom, m rus. номинальный ток, m pranc. courant assigné, m; courant de consigne, m; courant nominal, m ryšiai: sinonimas –… … Automatikos terminų žodynas
rated current — vardinė srovė statusas T sritis fizika atitikmenys: angl. nominal current; rated current vok. Nennstrom, m rus. номинальный ток, m pranc. courant assigné, m; courant nominal, m … Fizikos terminų žodynas
rated current — vardinė srovė statusas T sritis Standartizacija ir metrologija apibrėžtis Srovės stipris, pagal kurį nustatomos kai kurios transformatorinio skaitiklio charakteristikos. atitikmenys: angl. rated current vok. Nennstrom, m rus. номинальный ток, m… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
Current transformer — A CT for operation on a 110 kV grid In electrical engineering, a current transformer (CT) is used for measurement of electric currents. Current transformers, together with voltage transformers (VT) (potential transformers (PT)), are known as … Wikipedia
current rating — vardinė srovė statusas T sritis automatika atitikmenys: angl. current rating; nominal current; rated current vok. Nennstrom, m rus. номинальный ток, m pranc. courant assigné, m; courant de consigne, m; courant nominal, m ryšiai: sinonimas –… … Automatikos terminų žodynas
Rated R (Rihanna album) — Rated R Studio album by Rihanna Released November 20, 2009 ( … Wikipedia
Current limiting — is the practice in electrical or electronic circuits of imposing an upper limit on the current that may be delivered to a load with the purpose of protecting the circuit generating or transmitting the current from harmful effects due to a short… … Wikipedia
Current source — Figure 1: An ideal current source, I, driving a resistor, R, and creating a voltage V A current source is an electrical or electronic device that delivers or absorbs electric current. A current source is the dual of a voltage source. The term… … Wikipedia
Rated K — infobox television bgcolor=#000000 fgcolor=#FFFFFF show name = Rated K caption = format = Magazine, Lifestyle camera = picture format = 480i SDTV runtime = 1 hour creator = ABS CBN Broadcasting Corporation developer = ABS CBN News and Current… … Wikipedia
rated load — noun : the load a machine is designed to carry as usually stated on the nameplate in appropriate power units (as of horsepower for motors and engines or of kilovolt amperes for alternating current generators) * * * 1. the load a machine or… … Useful english dictionary
rated capacity — The quantity of electricity which can be drawn from a fully charged battery for 20 hours by a constant discharging current until cutoff voltage of 1.75 volts per cell is reached. Compare ampere hour capacity … Dictionary of automotive terms