-
81 Средняя рассеиваемая мощность диода
14. Средняя рассеиваемая мощность диода
D. Mittlere Verlustleistung der Diode
E. Average power dissipation
Pср
Среднее за период значение мощности, рассеиваемой диодом при протекании прямого и обратного токов
Источник: ГОСТ 25529-82: Диоды полупроводниковые. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-английский словарь нормативно-технической терминологии > Средняя рассеиваемая мощность диода
-
82 максимальная мощность рассеивания в держателе плавкой вставки
2.4 максимальная мощность рассеивания в держателе плавкой вставки (maximum power dissipation of the cartridge fuse-link): Мощность рассеивания в держателе плавкой вставки, значение которой:
2.4.1 в случае нагрузки сверхтоком PV1 равно значению максимальной выделяемой мощности в соответствии с ГОСТ Р 50538;
2.4.2 в случае номинальной нагрузки PV2равно значению номинальной выделяемой мощности при номинальных характеристиках, т.е. при максимальном рабочем напряжении и номинальном токе в соответствии с ГОСТ Р 50538.
Источник: ГОСТ Р 50030.7.3-2009: Аппаратура распределения и управления низковольтная. Часть 7.3. Электрооборудование вспомогательное. Требования безопасности к колодкам выводов для плавких предохранителей оригинал документа
Русско-английский словарь нормативно-технической терминологии > максимальная мощность рассеивания в держателе плавкой вставки
-
83 Средняя рассеиваемая мощность тиристора
90. Средняя рассеиваемая мощность тиристора
E. Mean power dissipation
F. Puissance dissipée moyenne
Pср
Сумма всех средних мощностей, рассеиваемых тиристором
Источник: ГОСТ 20332-84: Тиристоры. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-английский словарь нормативно-технической терминологии > Средняя рассеиваемая мощность тиристора
-
84 Средняя рассеиваемая мощность в открытом состоянии тиристора
94. Средняя рассеиваемая мощность в открытом состоянии тиристора
E. Mean on-state power dissipation
F. Puissance dissipée moyenne à l’état passant
Pос,ср
Произведение мгновенных значений тока и напряжения в открытом состоянии тиристора, усредненное по всему периоду
Источник: ГОСТ 20332-84: Тиристоры. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-английский словарь нормативно-технической терминологии > Средняя рассеиваемая мощность в открытом состоянии тиристора
-
85 Средняя рассеиваемая мощность управления тиристора
102. Средняя рассеиваемая мощность управления тиристора
E. Mean gate power dissipation
F. Puissance dissipée moyenne de gâchette
py,ср
Произведение мгновенных значений тока и напряжения управления, усредненного по всему периоду
Источник: ГОСТ 20332-84: Тиристоры. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-английский словарь нормативно-технической терминологии > Средняя рассеиваемая мощность управления тиристора
-
86 Средняя рассеиваемая мощность полупроводникового излучателя
25. Средняя рассеиваемая мощность полупроводникового излучателя
Средняя рассеиваемая мощность
Average power dissipation
Pрас.ср
Среднее за период значение мощности, рассеиваемой полупроводниковым излучателем при протекании тока в прямом и обратном направлениях
Источник: ГОСТ 27299-87: Приборы полупроводниковые оптоэлектронные. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-английский словарь нормативно-технической терминологии > Средняя рассеиваемая мощность полупроводникового излучателя
-
87 Средняя рассеиваемая мощность коллектора
65. Средняя рассеиваемая мощность коллектора
D. Mittlere Kollektorverlustleistung
E. Collector (average) power dissipation
F. Ruissance dissipée (moyenne) au collecteur
65б. Коэффициент комбинационных составляющих третьего порядка биполярного транзистора
Е Third order intermodulation products factor
Источник: ГОСТ 20003-74: Транзисторы биполярные. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-английский словарь нормативно-технической терминологии > Средняя рассеиваемая мощность коллектора
-
88 рассеяние
1) dispersion
2) dissipation
3) < radio> leakage
4) scattering
5) spreading
6) straggling
7) <math.> variance
– атмосферное рассеяние
– беспорядочное рассеяние
– вынужденное рассеяние
– когерентное рассеяние
– комбинационное рассеяние
– магнитное рассеяние
– многократное рассеяние
– некогерентное рассеяние
– однократное рассеяние
– преимущественное рассеяние
– рассеяние во времени
– рассеяние возвратное
– рассеяние гиперрелеевское
– рассеяние комбинационное
– рассеяние междолинное
– рассеяние по частоте
– резонансное рассеяние
– серое рассеяние
– упругое рассеяние
– фоновое рассеяние
– чистое рассеяние
временное рассеяние канала — channel memory
рассеяние в дальней зоне — far-field scattering
рассеяние в непрямом направлении — nonforward scattering
рассеяние в обратном направлении — backward scattering
рассеяние в прямом направлении — forward scattering
рассеяние вокруг среднего значения — dispersion about the mean
рассеяние волн в тропосфере — tropospheric scattering
рассеяние комбинационное вынужденное — <opt.> stimulated Raman scattering
рассеяние комбинационное свободное — <opt.> spontaneous Raman scattering
рассеяние Мандельштама-Бриллюена вынужденное — <opt.> stimulated Brillouin scattering
рассеяние мощности на аноде — plate dissipation
рассеяние мощности на сетке — grid power dissipation
-
89 диссипация энергии
1) Engineering: energy dissipation, power dissipation2) Makarov: dissipation of energyУниверсальный русско-английский словарь > диссипация энергии
-
90 рассеивание энергии
1) General subject: energy degradation, energy dispersal2) Mathematics: dissipation of energy3) Makarov: energy dispersion4) Combustion gas turbines: energy dissipation5) General subject: power dissipationУниверсальный русско-английский словарь > рассеивание энергии
-
91 диссипированная энергия
-
92 потеря мощности
1. power loss2. power dissipation -
93 потеря мощности
1) Military: waste of power2) Engineering: capacity loss, horsepower loss3) Chemistry: power loss4) Construction: fluid loss5) Automobile industry: loss in power, loss of power6) Metallurgy: loss of efficiency7) Oil: power dissipation, power waste8) Automation: loss of capacity9) Makarov: power waste (энергии)10) Cement: failure -
94 длительный допустимый ток
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-английский словарь нормативно-технической терминологии > длительный допустимый ток
-
95 максимально допустимая мощность рассеивания
Engineering: maximum permissible dissipation, maximum power dissipationУниверсальный русско-английский словарь > максимально допустимая мощность рассеивания
-
96 мощность рассеяния на коллекторе
Engineering: collector dissipation, collector power dissipationУниверсальный русско-английский словарь > мощность рассеяния на коллекторе
-
97 мощность рассеяния на сетке
Electronics: grid dissipation, grid power dissipationУниверсальный русско-английский словарь > мощность рассеяния на сетке
-
98 мощность, рассеиваемая сеткой
Makarov: grid dissipation, grid power dissipationУниверсальный русско-английский словарь > мощность, рассеиваемая сеткой
-
99 диссипация энергии
energy dissipation, power dissipationРусско-английский политехнический словарь > диссипация энергии
-
100 рассеянная мощность
1) Mechanics: dissipated power2) Household appliances: scattered power3) Makarov: power dissipationУниверсальный русско-английский словарь > рассеянная мощность
См. также в других словарях:
CPU power dissipation — Central processing unit power dissipation or CPU power dissipation is the process in which central processing units (CPUs) consume electrical energy, and dissipate this energy both by the action of the switching devices contained in the CPU (such … Wikipedia
anode power dissipation — anodo galios sklaida statusas T sritis radioelektronika atitikmenys: angl. anode power dissipation vok. Anodenstreuleistung, f; Anodenverlustleistung, f rus. рассеяние мощности на аноде, n pranc. dissipation anodique, f … Radioelektronikos terminų žodynas
Power semiconductor device — Power semiconductor devices are semiconductor devices used as switches or rectifiers in power electronic circuits (switch mode power supplies for example). They are also called power devices or when used in integrated circuits, called power… … Wikipedia
Power management — is a feature of some electrical appliances, especially copiers, computers and computer peripherals such as monitors and printers, that turns off the power or switches the system to a low power state when inactive. One power management standard… … Wikipedia
Power MOSFET — A Power MOSFET is a specific type of Metal Oxide Semiconductor Field Effect Transistor (MOSFET) designed to handle large power. Compared to the other power semiconductor devices (IGBT, Thyristor...), its main advantages are high commutation speed … Wikipedia
Power electronic substrate — The role of the substrate in power electronics is to provide the interconnections to form an electric circuit (like a printed circuit board), and to cool the components. Compared to materials and techniques used in lower power microelectronics,… … Wikipedia
dissipation power — sklaidomoji galia statusas T sritis fizika atitikmenys: angl. dissipated power; dissipation power vok. dissipierte Leistung, f; zerstreute Leistung, f; Zerstreuungsleistung, f rus. рассеиваемая мощность, f pranc. puissance dissipée, f … Fizikos terminų žodynas
dissipation anodique — anodo galios sklaida statusas T sritis radioelektronika atitikmenys: angl. anode power dissipation vok. Anodenstreuleistung, f; Anodenverlustleistung, f rus. рассеяние мощности на аноде, n pranc. dissipation anodique, f … Radioelektronikos terminų žodynas
Power virus — A power virus is a malicious computer program that executes specific machine code in order to reach the maximum CPU power dissipation (thermal energy output for the central processing unit). Computer cooling apparatus are designed to dissipate… … Wikipedia
Power optimization (EDA) — Power optimization refers to the use of electronic design automation tools to optimize (reduce) the power consumption of a digital design, while preserving the functionality.Introduction and historyThe increasing speed and complexity of today’s… … Wikipedia
Dissipation — In physics, dissipation embodies the concept of a dynamical system where important mechanical models, such as waves or oscillations, lose[citation needed] energy over time, typically from friction or turbulence. The lost energy converts into heat … Wikipedia