-
1 аномальные условия (работы)
аномальные условия (работы)
-EN
abnormal conditions
conditions which may occur in the appliance or in the switch during normal operation
[IEC 61058-1, ed. 3.0 (2000-07)]
abnormal conditions of operation
operating conditions of low occurrence (typical only a few times during equipment lifetime)
NOTE These include human errors, loss of power supply, overvoltages, earthquake, etc. After such a condition has occurred, equipment inspection may be required.
[IEC 61936-1, ed. 2.0 (2010-08)]FR
conditions anormales
conditions qui peuvent se présenter dans l’appareil ou dans l'interrupteur durant une manoeuvre normale
[IEC 61058-1, ed. 3.0 (2000-07)]
conditions anormales de fonctionnement
conditions de fonctionnement rares (seulement quelques fois au cours de la vie du matériel)
NOTE Cela inclut les erreurs humaines, pertes d’alimentation, surtensions, séismes, etc. Après de telles conditions d'exploitation, une inspection de ces matériels peut être exigée.
[IEC 61936-1, ed. 2.0 (2010-08)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > аномальные условия (работы)
-
2 условия работы
условия работы
Совокупность значений параметров электротехнического изделия (электротехнического устройства, электрооборудования), характеризующих его работу в данный момент и при заданных условиях эксплуатации.
[ ГОСТ 18311-80]EN
operating conditions
characteristics which may affect performance of a component, device or equipment
NOTE – Examples of operating conditions are ambient conditions, characteristics of the power supply, duty cycle or duty type.
[IEV number 151-16-01]FR
conditions de fonctionnement, f, pl
caractéristiques qui peuvent influer sur le fonctionnement d'un composant, d’un dispositif ou d'un matériel
NOTE – Des exemples de conditions de fonctionnement sont les conditions ambiantes, les caractéristiques de l’alimentation électrique, le cycle de service, le type de service.
[IEV number 151-16-01]Различают:
- нормальные условия работы;
- особые условия работы
Тематики
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > условия работы
-
3 располагаемая мощность агрегата (электростанции)
- puissance disponible d’une centrale
- puissance disponible d'une tranche
- puissance disponible d'une centrale
располагаемая мощность агрегата (электростанции)
Установленная мощность генерирующего агрегата (электростанции), за вычетом ограничений его мощности.
[ ГОСТ 19431-84]EN
available capacity of a unit
the maximum power at which a unit can be operated continuously under the prevailing conditions
Note – This power may be gross or net.
[IEV ref 602-03-11]
available capacity of a power station
the maximum power at which a power station can be operated continuously under the prevailing conditions
Note – This power may be gross or net.
[IEV ref 602-03-12]FR
puissance disponible d'une tranche
puissance maximale réalisable en régime continu dans les conditions réelles où une tranche se trouve
Note – Cette puissance peut être brute ou nette.
[IEV ref 602-03-11]
puissance disponible d'une centrale
puissance maximale réalisable en régime continu dans les conditions réelles où une centrale se trouve
Note – Cette puissance peut être brute ou nette.
[IEV ref 602-03-12]Тематики
Синонимы
EN
DE
- verfügbare Leistung eines Blocks, f
- verfügbare Leistung eines Kraftwerks
FR
- puissance disponible d'une centrale
- puissance disponible d'une tranche
- puissance disponible d’une centrale
52. Располагаемая мощность агрегата (электростанции)
Располагаемая мощность
E. Available power station capacity
F. Puissance disponible d’une centrale
Установленная мощность генерирующего агрегата (электростанции), за вычетом ограничений его мощности
Источник: ГОСТ 19431-84: Энергетика и электрификация. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > располагаемая мощность агрегата (электростанции)
-
4 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
5 анормальный режим энергосистемы
аномалия энергосистемы
анормальный режим энергосистемы
Режим работы энергосистемы, при котором его электрические рабочие параметры, например, напряжение, ток, мощность, частота, устойчивость находятся вне нормы.
[Разработка типовых структурных схем микропроцессорных устройств РЗА на объектах ОАО "ФКС ЕЭС". Пояснительная записка. Новосибирск 2006 г.]
анормальный режим энергосистемы
—
[В.А.Семенов. Англо-русский словарь по релейной защите]EN
power system abnormality
power system electrical operating conditions, e.g. voltage, current, power, frequency, stability, outside of normal conditions
[IEV ref 448-13-01]FR
situation anormale d'un réseau d'énergie
conditions de fonctionnement électrique du réseau d'énergie, par exemple tension, courant, puissance, fréquence, stabilité, en dehors des conditions normales
[IEV ref 448-13-01]Тематики
EN
DE
- Netzanomalie, f
FR
Русско-французский словарь нормативно-технической терминологии > анормальный режим энергосистемы
-
6 коэффициент мощности
коэффициент мощности
Скалярная величина, равная отношению активной мощности двухполюсника к полной мощности.
[ ГОСТ Р 52002-2003]
коэффициент мощности (цепи)
Отношение активного сопротивления к полному сопротивлению при промышленной частоте в эквивалентной цепи, которая считается состоящей из последовательно соединенных индуктивного и активного сопротивлений
[ ГОСТ Р 52565-2006]EN
power factor
under periodic conditions, ratio of the absolute value of the active power P to the apparent power S:
NOTE – Under sinusoidal conditions, the power factor is the absolute value of the active factor.
[IEV ref 131-11-46]FR
facteur de puissance, m
en régime périodique, rapport de la valeur absolue de la puissance active P à la puissance apparente S:
NOTE – En régime sinusoïdal, le facteur de puissance est la valeur absolue du facteur de puissance active.
[IEV ref 131-11-46]
Для синусоидального тока коэффициент мощности равен косинусу угла сдвига фаз между напряжением и током, т. е. равен Cos φ.
После того, как стали массово применяться такие нелинейные нагрузки, как компьютеры и другое офисное и телекоммуникационное оборудование, термин коэффициент мощности перестал быть синонимом термина Cos φ.Тематики
- качество электрической энергии
- электромагнитная совместимость
- электроснабжение в целом
- электротехника, основные понятия
Близкие понятия
Действия
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > коэффициент мощности
-
7 контактор (контактный)
контактор (механический) 1
Контактный коммутационный аппарат с единственным положением покоя, с управлением не вручную, способным включать, проводить и отключать токи в нормальных условиях цепи, в том числе при рабочих перегрузках.
МЭК 60050(441-14-33).
Примечание. Контакторы можно характеризовать способом, которым обеспечивается создание усилия для замыкания главных контактов
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контактор
Двухпозиционный аппарат с самовозвратом, предназначенный для частых коммутаций токов, не превышающих токи перегрузки, и приводимый в действие двигательным приводом.
Примечание. Для аналогичных аппаратов без самовозврата следует применять термин «Контактор без самовозврата».
[ ГОСТ 17703-72]
контактор
Выключатель для дистанционного включения, отключения и переключения силовых электрических цепей
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
(mechanical) contactor
a mechanical switching device having only one position of rest, operated otherwise than by hand, capable of making, carrying and breaking currents under normal circuit conditions including operating overload conditions
NOTE – Contactors may be designated according to the method by which the force for closing the main contacts is provided.
[IEV number 441-14-33]FR
contacteur (mécanique)
appareil mécanique de connexion ayant une seule position de repos, commandé autrement qu'à la main, capable d'établir, de supporter et d'interrompre des courants dans les conditions normales du circuit, y compris les conditions de surcharge en service
NOTE – Les contacteurs peuvent être désignés suivant la façon dont est fourni l'effort nécessaire à la fermeture des contacts principaux.
[IEV number 441-14-33]1 Должно быть " контактный"
См., например, выключатель (контактный) - (mechanical) switch
Коммутационные аппараты следует классифицировать на контактные и полупроводниковые (solid-state)
[Интент]1. Контактор на относительно небольшой номинальный ток, это такой же коммутационный аппарат, как и пускатель, но без теплового реле (можно сказать, что пускатель это контактор плюс тепловое реле).
2. Контактор на большой номинальный ток выглядит совсем иначе
Отечественный контактор КТ-6063Число полюсов: 3
Номинальное напряжение главной цепи: 380 В
Номинальный ток главной цепи: 1000 А
Номинальное напряжение катушки: 380 В переменного тока
Контакторы электромагнитные серии КТ 6000 с естественным воздушным охлаждением предназначены для включения и отключения приемников электрической энергии на номинальное напряжение до 380 В переменного тока частоты 50 и 60Гц.
Используются в составе оборудования для включения мощных электрических машин и в аппаратуре автоматического включения резерва (АВР).3. Контакторами называют также коммутационные аппараты, коммутационная способность которых больше коммутационной способности реле (см. рис. ниже)
[Интент]
Рис. Tyco ElectronicsПараллельные тексты EN-RU
Although contactors are not strictly relays they have the same design principles. Like relays, they are remote controlled switches.
The difference is the considerably higher input power consumption, higher switching capacity, and larger size.
[Tyco Electronics]Хотя, строго говоря, контакторы не являются реле, их конструкция имеет много общего с конструкцией реле. Также как и реле, они представляют собой коммутационный аппарат с дистационным управлением.
Отличие состоит в том, что их входная цепь потребляет значительно больший ток, они имеют существенно большую коммутационную способность и их размеры также больше размеров реле.
[Перевод Интент]Недопустимые, нерекомендуемые
Тематики
Действия
Неправильно:- замыкать контактор; - размыкать контакторСинонимы
EN
- contact-maker
- contactor
- electric contactor
- electromechanical contactor
- M/C
- magnetic contactor
- mechanical contactor
- power contactor
DE
FR
Русско-французский словарь нормативно-технической терминологии > контактор (контактный)
-
8 источник питания постоянного напряжения и постоянного тока
- alimentation stabilisée en tension/courant
источник питания постоянного напряжения и постоянного тока
-
[IEV number 313-04-03]EN
constant voltage/constant current power supply
power supply which operates as a constant voltage or a constant current power supply, depending on load conditions
Source: 551-19-06
[IEV number 313-04-03]FR
alimentation stabilisée en tension/courant
alimentation qui stabilise soit en tension soit en courant, en fonction des conditions de charge
Source: 551-19-06
[IEV number 313-04-03]Тематики
EN
- constant voltage/constant current power supply
DE
FR
- alimentation stabilisée en tension/courant
Русско-французский словарь нормативно-технической терминологии > источник питания постоянного напряжения и постоянного тока
-
9 характеристика «напряжение-время»
- caractéristique de tenue d'un parafoudre sous tension à fréquence industrielle en fonction du temps
характеристика «напряжение-время»
Выдерживаемое напряжение промышленной частоты в зависимости от времени его приложения к ОПН. Показывает максимальный промежуток времени, в течение которого к ОПН может быть приложено напряжение промышленной частоты, превышающее Uнр, не вызывая повреждения или термической неустойчивости.
[ ГОСТ Р 52725-2007]EN
power-frequency withstand voltage versus time characteristic of an arrester
power-frequency withstand voltage versus time characteristic shows the maximum time durations for which corresponding power-frequency voltages may be applied to arresters without causing damage or thermal instability, under specified conditions in accordance with 6.10.
[IEC 60099-4, ed. 2.0 (2004-05)]FR
caractéristique de tenue d'un parafoudre sous tension à fréquence industrielle en fonction du temps
durées maximales pendant lesquelles les tensions à fréquence industrielle correspondantes peuvent être appliquées aux parafoudres sans entraîner de détérioration ou d'instabilité thermique, dans des conditions spécifiées selon 6.10
[IEC 60099-4, ed. 2.0 (2004-05)]Тематики
- высоковольтный аппарат, оборудование...
EN
- power-frequency withstand voltage versus time characteristic of an arrester
FR
- caractéristique de tenue d'un parafoudre sous tension à fréquence industrielle en fonction du temps
Русско-французский словарь нормативно-технической терминологии > характеристика «напряжение-время»
-
10 выдерживаемое напряжение промышленной частоты
выдерживаемое напряжение промышленной частоты
Действующее значение синусоидального напряжения промышленной частоты, не вызывающее пробоя в указанных условиях испытания.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
power-frequency withstand voltage
r.m.s. value of a power-frequency sinusoidal voltage which does not cause breakdown under specified conditions of test
[IEC 60947-1, ed. 5.0 (2007-06)]FR
tension de tenue à fréquence industrielle
valeur efficace d'une tension sinusoïdale à fréquence industrielle qui ne provoque pas de claquage dans des conditions d'essai spécifiées
[IEC 60947-1, ed. 5.0 (2007-06)]Тематики
- электротехника, основные понятия
EN
FR
Русско-французский словарь нормативно-технической терминологии > выдерживаемое напряжение промышленной частоты
-
11 номинальное напряжение ОПН
номинальное напряжение
Uн
Действующее значение напряжения промышленной частоты, которое ограничитель может выдерживать в течение 10 с в процессе рабочих испытаний. Номинальное напряжение должно быть не менее 1,25 наибольшего длительно допустимого рабочего напряжения.
[ ГОСТ Р 52725-2007]EN
rated voltage of an arrester
Ur
maximum permissible r.m.s. value of power-frequency voltage between its terminals at which it is designed to operate correctly under temporary overvoltage conditions as established in the operating duty tests
NOTE 1 The rated voltage is used as a reference parameter for the specification of operating characteristics.
NOTE 2 The rated voltage as defined in this standard is the 10 s power-frequency voltage used in the operating duty test after high-current or long-duration impulses. Tests used to establish the voltage rating in IEC 60099-1, as well as some national standards, involve the application of repetitive impulses at nominal current with power-frequency voltage applied. Attention is drawn to the fact that these two methods used to established rating do not necessarily produce equivalent values (a resolution to this discrepancy is under consideration).
[IEC 60099-4, ed. 2.0 (2004-05)]FR
tension assignée d'un parafoudre
Ur
valeur maximale de la tension efficace à fréquence industrielle admissible entre ses bornes pour laquelle le parafoudre est prévu pour fonctionner correctement dans des conditions de surtension temporaires comme il est défini dans les essais de fonctionnement
NOTE 1 La tension assignée est utilisée comme paramètre de référence pour la spécification des caractéristiques de fonctionnement.
NOTE 2 La tension assignée comme définie dans la présente norme est la tension à fréquence industrielle de 10 s, utilisée pour vérifier la stabilité après application des chocs de courant de grande amplitude ou de longue durée lors de l'essai de fonctionnement. Les essais utilisés pour définir la tension assignée dans la CEI 60099-1, ainsi que dans certaines normes nationales, impliquent l'application de chocs répétés au courant nominal pendant que la tension à fréquence industrielle est appliquée. On attire l'attention sur le fait que ces deux méthodes utilisées pour définir les valeurs assignées ne produisent pas nécessairement des valeurs équivalentes (une résolution de cette différence est à l'étude).
[IEC 60099-4, ed. 2.0 (2004-05)]Тематики
- высоковольтный аппарат, оборудование...
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение ОПН
-
12 входное полное сопротивление
входное полное сопротивление
-
[IEV number 312-06-18]EN
input impedance
impedance of the input circuit measured between the input terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the input circuit is such that the instantaneous value of the current flowing into the input terminals is a non-linear function of the instantaneous value of the input voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual input circuit, is sometimes called the "equivalent input impedance".
[IEV number 312-06-18]FR
impédance du circuit d'entrée
impédance du circuit d'entrée entre les bornes d'entrée dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit d'entrée est tel que la valeur instantanée du courant traversant les bornes d'entrée est une fonction non linéaire de la valeur instantanée de la tension d'entrée dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit d'entrée réel, est parfois appelée "impédance équivalente d'entrée".
[IEV number 312-06-18]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > входное полное сопротивление
-
13 выходное полное сопротивление
выходное полное сопротивление
-
[IEV number 312-06-19]EN
output impedance
impedance of the output circuit measured between the output terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the output circuit is such that the instantaneous value of the current flowing into the output terminals is a non-linear function of the instantaneous value of the output voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual output circuit, is sometimes called the "equivalent output impedance".
[IEV number 312-06-19]FR
impédance du circuit de sortie
impédance du circuit de sortie entre les bornes de sortie dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit de sortie est tel que la valeur instantanée du courant traversant les bornes de sortie est une fonction non linéaire de la valeur instantanée de la tension de sortie dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit de sortie réel, est parfois appelée "impédance équivalente de sortie".
[IEV number 312-06-19]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выходное полное сопротивление
-
14 электрическая нагрузка
1. Любой потребитель электроэнергии
электрическая нагрузка
Любой приемник(потребитель)электрической энергии в электрической цепи 1)
[БЭС]
нагрузка
Устройство, потребляющее мощность
[СТ МЭК 50(151)-78]EN
load (1), noun
device intended to absorb power supplied by another device or an electric power system
[IEV number 151-15-15]FR
charge (1), f
1) Иными словами (электрическая) нагрузка, это любое устройство или группа устройств, потребляющих электрическую энергию (электродвигатель, электролампа, электронагреватель и т. д.)
dispositif destiné à absorber de la puissance fournie par un autre dispositif ou un réseau d'énergie électrique
[IEV number 151-15-15]
[Интент]
Термимн нагрузка удобно использовать как обощающее слово.
В приведенном ниже примере термин нагрузка удачно используется для перевода выражения any other appliance:
Make sure that the power supply and its frequency are adapted to the required electric current of operation, taking into account specific conditions of the location and the current required for any other appliance connected with the same circuit.
Ток, напряжение и частота источника питания должны соответствовать параметрам агрегата с учетом длины и способа прокладки питающей линии, а также с учетом другой нагрузки, подключенной к этой же питающей линии.
[Перевод Интент]
... подключенная к трансформатору нагрузка
[ ГОСТ 12.2.007.4-75*]
Поскольку приемник электрической энергии это любой аппарат, агрегат, механизм, предназначенный для преобразования электрической энергии в другой вид энергии [ПУЭ], то термин нагрузка может характеризовать электроприемник с точки зрения тока, сопротивления или мощности.
2. Потребитель энергоэнергии, с точки зрения потребляемой мощности
нагрузка
Мощность, потребляемая устройством
[СТ МЭК 50(151)-78]EN
load (2), noun
power absorbed by a load
[IEV number 151-15-16]FR
charge (2), f
puissance absorbée par une charge
Source: 151-15-15
[IEV number 151-15-16]
При проектировании электроснабжения энергоемких предприятий следует предусматривать по согласованию с заказчиком и с энергоснабжающей организацией регулирование электрической нагрузки путем отключения или частичной разгрузки крупных электроприемников, допускающих без значительного экономического ущерба для технологического режима перерывы или ограничения в подаче электроэнергии.
[СН 174-75 Инструкция по проектированию электроснабжения промышленных предприятий]
В настоящее время характер коммунально-бытовой нагрузки кардинально изменился в результате широкого распространения новых типов электроприемников (микроволновых печей, кондиционеров, морозильников, люминесцентных светильников, стиральных и посудомоечных машин, персональных компьютеров и др.), потребляющих из питающей сети наряду с активной мощностью (АМ) также и значительную реактивную мощность (РМ).Недопустимые, нерекомендуемые
Тематики
- электроснабжение в целом
- электротехника, основные понятия
Классификация
>>>Близкие понятия
Действия
- аварийное отключение нагрузки
- аварийный сброс нагрузки
- включение нагрузки
- защитное отключение нагрузки
- ограничение допустимых нагрузок
- отключение нагрузки
- отключение неприоритетных нагрузок
- передача нагрузки с одной системы шин на другую
- питание нагрузки
- регулирование электрической нагрузки
Синонимы
Сопутствующие термины
- нагрузки жилых зданий
- нагрузки общественных зданий
- территориальное расположение нагрузок
- ток нагрузки
- токовая нагрузка
- характер коммунально-бытовой наргрузки
- характер нагрузки (индуктивный, емкостной)
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > электрическая нагрузка
-
15 нагревательный элемент с видимым свечением
нагревательный элемент с видимым свечением
Нагревательный элемент, который виден снаружи прибора частично или полностью и температура которого по меньшей мере 650 оС после достижения прибором установившегося состояния при номинальной потребляемой мощности в условиях нормальной работы.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
visibly glowing heating element
heating element that is partly or completely visible from the outside of the appliance and has a temperature of at least 650 °C when the appliance has been operated under normal operation at rated power input until steady conditions have been established
[IEC 60335-1, ed. 4.0 (2001-05)]FR
élément chauffant lumineux
élément chauffant qui est partiellement ou complètement visible de l'extérieur de l'appareil et ayant une température au moins égale à 650 °C après que l'appareil a été mis en fonctionnement dans les conditions de fonctionnement normal à la puissance assignée jusqu'à l'établissement des conditions de régime
[IEC 60335-1, ed. 4.0 (2001-05)]Тематики
Обобщающие термины
EN
FR
Русско-французский словарь нормативно-технической терминологии > нагревательный элемент с видимым свечением
-
16 токоограничивающий реактор
- bobine d’inductance de limitation de courant
токоограничивающий реактор
-
[ ГОСТ 18624-73]EN
current-limiting reactor
reactor connected in series in a power system to limit the current under system fault conditions
[IEC 60076-6, ed. 1.0 (2007-12)]
series reactor
a reactor intended for series connection in a network, either for limiting the current under fault conditions or for load-sharing in parallel circuits
[IEV ref 421-01-02]FR
bobine d’inductance de limitation de courant
bobine d’inductance connectée en série dans un réseau pour limiter le courant en cas de conditions de défaut dans le réseau
[IEC 60076-6, ed. 1.0 (2007-12)]
(bobine d')inductance série
bobine d'inductance destinée à être placée en série dans un réseau, soit pour limiter le courant dans le cas de défaut dans le réseau, soit pour répartir la charge dans des circuits en parallèle
[IEV ref 421-01-02]Тематики
Классификация
>>>Обобщающие термины
EN
FR
- bobine d’inductance de limitation de courant
Русско-французский словарь нормативно-технической терминологии > токоограничивающий реактор
-
17 НКУ распределения и управления
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
Русско-французский словарь нормативно-технической терминологии > НКУ распределения и управления
-
18 обозначение класса (для счетчика энергии)
обозначение класса (для счетчика энергии)
-
[IEV number 314-07-06]EN
class index (of an energy meter)
number which gives the limits of the absolute value of the permissible relative error, expressed in percent, within a specified range of values for the current, for unity power factor (and in the case of polyphase meters with balanced loads) when the meter is tested under reference conditions (including the permitted tolerances on the reference values)
[IEV number 314-07-06]FR
indice de classe (d'un compteur d'énergie)
nombre qui donne les limites de la valeur absolue de l’erreur relative admissible, exprimée en pourcent, dans une plage spécifiée de valeurs du courant, pour le facteur de puissance égal à l’unité (et dans le cas des compteurs polyphasés avec charges équilibrées), lorsque le compteur est essayé dans les conditions de référence (y compris les tolérances permises sur les valeurs de référence)
[IEV number 314-07-06]Тематики
- измерение электр. величин в целом
- счетчик электроэнергии
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > обозначение класса (для счетчика энергии)
-
19 открытая подстанция
открытая подстанция
Электрическая подстанция, оборудование которой расположено на открытом воздухе.
[ ГОСТ 24291-90]EN
outdoor substation
a substation which is designed and installed to withstand external weather conditions
[IEV number 605-02-16]
air-insulated substation
An electric power substation that has the busbars and equipment terminations generally open to air and utilizes insulation properties of ambient air for insulation to ground.
[ http://www.answers.com/topic/air-insulated-substation]FR
poste extérieur
poste conçu et installé pour supporter les conditions atmosphériques extérieures
[IEV number 605-02-16]Тематики
EN
DE
FR
Электрическая подстанция, оборудование которой расположено на открытом воздухе
605-02-16
de Freiluftstation
en outdoor substation
fr poste extérieur
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > открытая подстанция
-
20 ток нагрузки
ток нагрузки
-EN
load current
current flowing through the line conductor/s
[IEC 61557-13, ed. 1.0 (2011-07)]
load current
the r.m.s. value of the current in any winding under service conditions
[IEC 60076-1, ed. 3.0 (2011-04)]
load current
current to which the devices are subjected to produce power loss P
[IEC 60749-34, ed. 2.0 (2010-10)]FR
courant de charge
courant circulant à travers le (les) conducteur(s) de ligne
[IEC 61557-13, ed. 1.0 (2011-07)]
courant de charge
<>la valeur efficace vraie (r.m.s.) du courant dans tout enroulement en conditions de service
[IEC 60076-1, ed. 3.0 (2011-04)]
courant de charge
courant auquel sont soumis les dispositifs pour produire la perte de puissance P
[IEC 60749-34, ed. 2.0 (2010-10)]Параллельные тексты EN-RU
If it is left ON or OFF for a long time, it is recommended to switch load current on a regular basis.
[LS Industrial Systems]Если (автоматический выключатель) продолжительное время находится во включенном или отключенном состоянии, то рекомендуется периодически коммутировать этим выключателем ток нагрузки.
[Перевод Интент]Тематики
- электротехника, основные понятия
EN
FR
Русско-французский словарь нормативно-технической терминологии > ток нагрузки
- 1
- 2
См. также в других словарях:
Power Good Signal — In addition to the voltages and currents that a computer needs to operate, power supplies also provide a signal called the Power Good signal, sometimes written as Power OK or Power Good. Its purpose is to tell the computer all is well with the… … Wikipedia
Power supply unit (computer) — Power supply unit with top cover removed A power supply unit (PSU) supplies direct current (DC) power to the other components in a computer. It converts general purpose alternating current (AC) electric power from the mains (110 V to… … Wikipedia
CONDITIONS — (Heb. תְּנָאִים, tena im). Definition Conditions is an ambiguous word inasmuch as it refers not only to the external factors upon which the existence of an agreement is made to depend but also to the actual terms of the contract itself. Thus, one … Encyclopedia of Judaism
Power steering — helps drivers steer vehicles by augmenting steering effort of the steering wheel. It does this by adding controlled energy to the steering mechanism, so the driver needs to provide only modest effort regardless of conditions. In particular, power … Wikipedia
Power system simulation — models are a class of computer simulation programs that focus on the operation of electrical power systems. These computer programs are used in a wide range of planning and operational situations including: #Long term generation and transmission… … Wikipedia
Power system protection — is a branch of electrical power engineering that deals with the protection of electrical power systems from faults through the isolation of faulted parts from the rest of the electrical network. The objective of a protection scheme is to keep the … Wikipedia
Power engineering — Power engineering, also called power systems engineering, is a subfield of electrical engineering that deals with the generation, transmission and distribution of electric power as well as the electrical devices connected to such systems… … Wikipedia
Power Pro Kun Pocket series — (パワプロクンポケットシリーズ, abbrv. :パワポケ), or simply called Pawapoke or Power Pocket, is the sub series(spinoff) of the Jikkyō Powerful Pro Yakyū series baseball game developed by Konami. The series is released only on the Nintendo s handheld platform (GBC … Wikipedia
Power Rangers Mystic Force — Format Action/Adventure Fantasy Starring Firass Dirani … Wikipedia
Power control — Power control, broadly speaking, is the intelligent selection of transmit power in a communication system to achieve good performance within the system. The notion of good performance can depend on context and may include optimizing metrics such… … Wikipedia
Conditions on Transformations — is an influential linguistics article by Noam Chomsky, published in 1973[1]. In it, Chomsky attempted to formulate constraints on transformational rules used in Transformational Generative Grammar (TGG), a new kind of syntactic theory that… … Wikipedia