one+need

 

(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]

Этот ток обозначают I_Z
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]

EN

(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]

ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]

FR

courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]

Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:

• its insulation temperature rating;
• conductor electrical properties for current;
• frequency, in the case of alternating currents;
• ability to dissipate heat, which depends on cable geometry and its surroundings;
• ambient temperature.

Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.

The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.

In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.

Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.

The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.

For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.

Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.

When designing an electrical system, one will normally need to know the current rating for the following:

• Wires
• Printed Circuit Board traces, where included
• Fuses
• Circuit breakers
• All or nearly all components used

Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.

[http://en.wikipedia.org/wiki/Ampacity]

Тематики

• электротехника, основные понятия

Синонимы

• длительно допустимый ток
• допустимый ток

EN

• ampacity (US)
• continuous current
• continuous current-carrying capacity
• current-carrying capacity

DE

• Dauerstrombelastbarkeit, f
• Strombelastbarkeit, f

FR

• courant admissible, m
• courant permanent admissible, m

 

исчезающие виды
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

EN

endangered species (IUCN)
One of the three degrees of "rarity" drawn up by the International Union for the Conservation of Natural Resources. All plants and animals in these categories need special protection. Endangered species are those species in danger of extinction unless steps are taken to change the cause of threat and decline. (Source: BRACK)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

Тематики

• охрана окружающей среды

EN

• endangered species (IUCN)

DE

• gefährdete Arten

FR

• espčce menacée

 

пол плавающий
Пол, отделённый от основания и стен амортизирующими прослойками или изолирующими устройствами для повышения звукоизоляции смежных помещений
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]

EN

floating floor
The upper layer of floor construction supported on battens, mountings or a resilient sheet membrane of damping material such as expanded polystyrene or mineral wool to provide acoustic isolation.

---

floating floor
A floating floor is a floor that does not need to be nailed or glued to the subfloor. The term floating floor refers to the installation method, but is often used synonymously with laminate flooring in a domestic context.
A sprung floor is a special type of floating floor designed to enhance sports or dance performance. In general though the term refers to a floor used to reduce noise or vibration.
A domestic floating floor might be constructed over a subfloor or even over an existing floor. It can consist of a glass fibre, felt or cork layer for sound insulation with neoprene pads holding up a laminate floor. There is a gap between the floating floor and the walls to decouple them and allow for expansion; this gap is covered with skirting boards or mouldings.
Floating floors as used in sound studios can be either just larger versions of the domestic variety, or much larger constructions with slabs of concrete to keep the resonance frequency down. The manufacture of integrated circuits uses massive floating floors with hundreds of tons in weight of concrete to avoid vibration affecting mask alignment.
Floating floors are one of the requirements for the THX high-fidelity sound reproduction standard for movie theaters, screening rooms, home theaters, computer speakers, gaming consoles, and car audio systems.
While floating floors add to the appeal of a home, they are not recommended for areas that may get wet, i.e. bathrooms and near exterior doors.
[http://en.wikipedia.org/wiki/Floating_floor]

Тематики

• элементы зданий и сооружений

EN

• floating floor

DE

• schwimmender Estrich

FR

• plancher flottant