-
81 прекращение/отказ
(Статья контракта.)termination/rejection1. Если Поставщик не выполняет каких-либо свих обязательств по Контракту, для его предприятия назначается ликвидатор или подвергается процедуре банкротства в добровольном или принудительном порядке, или Компания обоснованно считает, что любое из этих событий может произойти, Компания имеет право по своему усмотрению без ущерба любому другому средству приостановить или прекратить действие Контракта и в случае прекращения оставить у себя любые Товары или вступить во владение ими или любыми изделиями, принадлежащими Компании, и с этой целью входить в любые помещения Поставщика. — 1. If the Supplier defaults in any of its obligations under the Contract becomes insolvent has a receiver appointed of its business or is compulsorily or voluntarily wound up or if the Company bona fide believes that any of such events may occur the Company shall be entitled at its discretion without prejudice to any other remedy to suspend the performance of or terminate the Contract and in the event of termination to keep or take possession of any Goods or of any items belonging to the Company and to enter any premises of the Supplier for that purpose.
2. Если Компания прекращает действие Контракта, Поставщик обязан вернуть Компании все произведенные платежи. Если Компания отказывается от каких-либо Товаров, Поставщик обязан вернуть Компании все произведенные платежи по отвергнутым Товарам. Если по прекращении действия Контракта Компания принимает решение оставить у себя или принять какие-либо Товары, она производит по ним зачет для Поставщика пропорционально их цене или стоимости для Компании в зависимости от того, какая сумма меньше, но в противном случае, после прекращения или отказа, выплата компенсации Поставщику не предусматривается. — 2. If the Company terminates the Contract the Supplier shall return to the Company all payments made and if the Company rejects any Goods the Supplier shall return all payments already made for the rejected Goods. Where upon termination the Company elects to keep or take any Goods it shall account to the Supplier for them at a proportion of their price or their value to the Company whichever is less but otherwise no compensation shall be payable to the Supplier on termination or rejection.
Russian-English Dictionary "Microeconomics" > прекращение/отказ
-
82 математическое ожидание
1. expectation2. expectation value3. population meanРусско-английский большой базовый словарь > математическое ожидание
-
83 низкий
1. give-away2. inferior3. off4. poorнизкая точность; недостаточная точность — poor accuracy
5. therein after therein underниже, в дальнейшем — herein after
6. ignoble7. vile8. hereafter9. in the following10. rough11. subambient12. in what follows13. lour14. low calorific valueрадио, низкая частота — low frequency
15. lowlyнебывало низкая цена; небывало низкий уровень — all-time low
16. thereunder17. below; beneath; under; lower; shorter18. low; mean; base; shortбыть ниже нормы; быть ниже стандарта — be below the standard
19. base20. dishonorable21. dishonourable22. meanСинонимический ряд:1. гуще (прил.) басистее; басовитее; гуще; жирнее; толще2. приземистее (прил.) короче; приземистее -
84 виды коррекции коэффициента мощности
виды коррекции коэффициента мощности
-There are 2 types of power factor correction: fixed or automatic.
Fixed power factor correction consists of inserting, in parallel on the network, a capacitor bank whose total power is provided by the assembly of capacitors of identical or different ratings. The bank is energized by a contactor that simultaneously supplies all the capacitors (a single step).
The inrush current peak, in the case of fixed correction, can reach 30 times the nominal current of the capacitor bank.
An automatic power factor correction system, on the other hand, consists of several capacitor banks of identical or different ratings (several steps), energized separately according to the value of the power factor to be corrected.
An electronic device automatically determines the power of the steps to be energized and activates the relevant contactors.
The inrush current peak, in the case of automatic correction, depends on the power of the steps already on duty, and can reach 100 times the nominal current of the step to be energized.
[ABB]
PFC Types
There are two types of Power Factor Correction - Passive PFC and Active PFC.
Passive PFC uses passive elements like a ferrite core inductor on the AC input. It is very easy to implement in existing power circuits although the power factor is low at 60-80%. The proper AC input voltage (115V or 230V) must also be chosen manually. In addition, significant EMI can still result with a 115V AC source. Of course, a 230V AC source will not have this problem!.
Active PFC, on the other hand, uses a switching regulator with active elements like an IC, FETs (Field Effect Transistors) and diodes to create an active PFC circuit. This circuit allows the power supply to achieve a power factor of up to 95%, significantly reduce harmonics and automatically adjusts the AC input voltage. This means you do not have to manually select the AC input voltage. It works with all voltages from 110V to 240V.
[ http://www.techarp.com/showarticle.aspx?artno=81&pgno=1]
Тематики
EN
Русско-английский словарь нормативно-технической терминологии > виды коррекции коэффициента мощности
-
85 действие электрической дуги, возникающей внутри НКУ распределения и управления
действие электрической дуги, возникающей внутри НКУ распределения и управления
-
[Интент]Параллельные тексты EN-RU
Effects of the electric arc inside switchgear and controlgear assemblies
In the proximity of the main boards, i.e. in the proximity of big electrical machines, such as transformers or generators, the short-circuit power is high and consequently also the energy associated with the electrical arc due to a fault is high.
Without going into complex mathematical descriptions of this phenomenon, the first instants of arc formation inside a cubicle can be schematized in 4 phases:
1. compression phase: in this phase the volume of the air where the arc develops is overheated owing to the continuous release of energy; due to convection and radiation the remaining volume of air inside the cubicle warms up; initially there are temperature and pressure values different from one zone to another;
2. expansion phase: from the first instants of internal pressure increase a hole is formed through which the overheated air begins to go out. In this phase the pressure reaches its maximum value and starts to decrease owing to the release of hot air;
3. emission phase: in this phase, due to the continuous contribution of energy by the arc, nearly all the air is forced out under a soft and almost constant overpressure;
4. thermal phase: after the expulsion of the air, the temperature inside the switchgear reaches almost that of the electrical arc, thus beginning this final phase which lasts till the arc is quenched, when all the metals and the insulating materials coming into contact undergo erosion with production of gases, fumes and molten material particles.
Should the electrical arc occur in open configurations, some of the described phases could not be present or could have less effect; however, there shall be a pressure wave and a rise in the temperature of the zones surrounding the arc.
Being in the proximity of an electrical arc is quite dangerous; here are some data to understand how dangerous it is:
• pressure: at a distance of 60 cm from an electrical arc associated with a 20 kA arcing fault a person can be subject to a force of 225 kg; moreover, the sudden pressure wave may cause permanent injuries to the eardrum;
• arc temperatures: about 7000-8000 °C;
• sound: electrical arc sound levels can reach 160 db, a shotgun blast only 130 db.
[ABB]Действие электрической дуги, возникающей внутри НКУ распределения и управления
Короткое замыкание вблизи больших силовых устройств, таких как трансформаторы или генераторы имеет очень большую мощность. Поэтому энергия электрической дуги, возникшей в результате короткого замыкания, очень большая.
Не вдаваясь в сложное математическое описание данного явления, можно сказать, что первые мгновения формирования дуги внутри шкафа можно упрощенно разделить на четыре этапа:
1. Этап сжатия: на этом этапе объем воздуха, в котором происходит зарождение дуги перегревается вследствие непрерывного высвобождения энергии. За счет конвекции и излучения оставшийся объем воздуха внутри шкафа нагревается. На этом начальном этапе значения температуры и давления воздуха в разных зонах НКУ разные.
2. Этап расширения: с первых мгновений внутреннее давление создает канал, через который начинается движение перегретого воздуха. На этом этапе давление достигает своего максимального значения, после чего начинает уменьшаться вследствие выхода горячего воздуха.
3. Этап эмиссии: на этом этапе вследствие непрерывного пополнения энергией дуги почти весь воздух выталкивается под действием мягкого и почти постоянного избыточного давления.
4. Термический этап: после выхлопа воздуха температура внутри НКУ почти достигает температуры электрической дуги. Так начинается заключительный этап, который длится до тех пор, пока дуга не погаснет. При этом все металлические и изоляционные материалы, вступившие в контакт с дугой, оказываются подвергнутыми эрозии с выделением газов, дыма и частиц расплавленного материала.
Если электрическая дуга возникнет в открытом НКУ, то некоторые из описанных этапов могут не присутствовать или могут иметь меньшее воздействие. Тем не менее будет иметь место воздушная волна и подъем температуры вблизи дуги.
Находиться вблизи электрической дуги довольно опасно. Ниже приведены некоторые сведения, помогающие осознать эту опасность:
• давление: На расстоянии 60 см от электрической дуги, вызванной током короткого замыкания 20 кА, человек может подвергнуться воздействию силы 225 кг. Более того, резкая волна давления может нанести тяжелую травму барабанным перепонкам;
• температура дуги: около 7000-8000 °C;
• шумовое воздействие: Уровень шумового воздействия электрической дуги может достигнуть 160 дБ (выстрел из дробовика – 130 дБ).
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
Русско-английский словарь нормативно-технической терминологии > действие электрической дуги, возникающей внутри НКУ распределения и управления
-
86 платежи
платежи
Данный термин означает платежи, получаемые Оргкомитетом «Сочи-2014»:
• по всем контрактам, относящимся к Совместной маркетинговой программе Оргкомитета «Сочи-2014» или содержащим любые элементы коммерческого использования символики Оргкомитета «Сочи-2014», символики ОКР либо так или иначе связанным с Играми, включая без ограничений доходы от продажи входных билетов на соревнования Игр;
• по всем контрактам на вклады в натуральной форме и другим формам вознаграждения за любые рекламные, льготные и другие права или в связи с ними.
[Департамент лингвистических услуг Оргкомитета «Сочи 2014». Глоссарий терминов]EN
consideration
Term refers to consideration received by Sochi 2014:
• of all contracts pertaining to the Sochi 2014 joint marketing program or containing any element of commercial exploitation of the Sochi 2014 marks, the ROC marks, or relating to the Games in any way, including but not limited to the revenues for the sale of admission tickets to the Games;
• of all contracts which provide for value-in-kind or other forms of consideration to be supplied in return for, or in connection with, any advertising, promotional or other rights.
[Департамент лингвистических услуг Оргкомитета «Сочи 2014». Глоссарий терминов]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > платежи
-
87 управление подрядчиками
управление подрядчиками
(ITIL Service Design)
Процесс, отвечающий за обеспечение оптимального соотношения цена-качество при работе с поставщиками, обеспечивающий соответсвие договоров и соглашений нуждам бизнеса и выполнение подрядчиками своих контрактных обязательств.
См. тж. система управления подрядчиками и контрактами.
[Словарь терминов ITIL версия 1.0, 29 июля 2011 г.]EN
supplier management
(ITIL Service Design)
The process responsible for obtaining value for money from suppliers, ensuring that all contracts and agreements with suppliers support the needs of the business, and that all suppliers meet their contractual commitments.
See also supplier and contract management information system.
[Словарь терминов ITIL версия 1.0, 29 июля 2011 г.]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > управление подрядчиками
-
88 "дуговая" неисправность
"дуговая" неисправность
Неисправность, приводящая к возникновению дуги.
[Интент]Параллельные тексты EN-RU
An arc fault occurs when there is a reduction in the dielectric strength of the insulating means (air, in LV switchboards) interposed between two or more conducting elements at different potential.
The arc is generated at the moment when, due to the high ionization of the air, there is a breakdown of the dielectric of the medium and the consequent flow of the current through it.
In an arc fault the highest stresses are of thermal type and proportional to RaI2 owing to the high value taken by the arc resistance Ra; this because the fault current flows in a medium which is always insulating, even if extremely ionized.
Such stresses manifest themselves essentially in the form of:
• high thermal gradients caused by the quick and intense rise in the air temperature;
• high pressure gradients in the form of pressure wave;
• high ionization of the air with consequent reduction of its insulating strength.
Generally speaking, in a LV assembly designed and tested according to the Standard IEC 60439-1 an arc fault is not very likely to occur; however, should it occur, the consequences would be extremely harmful to both the equipment as well as the personnel (see Chapters 2.2 and 2.3).
The causes of an arc fault can be both technical as well as non technical; among the latter the most frequent are the following:
• personnel errors, above all during maintenance operations;
• installation operations not sufficiently accurate;
• inadequate maintenance, above all in the case of severe environmental conditions.
Among the technical causes of an arc fault in a LV assembly the following ones are to be remembered:
• breakdown of the insulation essentially in the proximity of the supports of the busbars and of the plug-in contacts of the withdrawable units (75% of cases);
• overvoltages generating disruptive discharges between the points at minimum clearances (15% of cases);
• constructional defects of the apparatus (10% of cases).
[ABB]К «дуговой» неисправности, относится неисправность, обусловленная уменьшением электрической прочности изолирующей среды (воздуха в НКУ) между двумя или более токоведущими частями, находящимися под разными электрическими потенциалами.
Дуга образуется в тот момент, когда вследствие высокой ионизации воздуха происходит пробой изолирующей среды, вследствие чего через нее начинает протекать электрический ток.
Проявлением дуговой неисправности, является тепловое воздействие, пропорциональное RaI2 и достигающее большого значения вследствие большого сопротивления дуги Ra.
Дело в том, что ток дуги протекает через среду, которая всегда является изолирующей, пусть даже и чрезвычайно ионизированной.
Указанные воздействия очевидны сами по себе особенно в форме:
• теплового градиента температуры, вызванного быстрым и интенсивным подъемом температуры воздуха;
• высоким градиентом давления в форме волны давления;
• высокой ионизацией воздуха с последующим уменьшением электрической прочности.
Вообще говоря, в НКУ, разработанных и испытанных в соответствии с требованиями стандарта МЭК 60439-1 «дуговая» неисправность маловероятна. Однако, если дуга все таки возникнет, ее последствия буду чрезвычайно тяжелыми как для оборудования, так и для персонала (см. п. 2.2 и 2.3).
Причина дуговой неисправности может носить как технический, так и нетехнический характер. Среди последних наиболее часто возникают следующие:
• ошибки персонала, совершаемые главным образом во время технического обслуживания;
• недостаточно аккуратное выполнение монтажа;
• ненадлежащее техническое обслуживание, главным образом при эксплуатации НКУ в тяжелых условиях окружающей среды.
Среди технических причин дуговой неисправности в НКУ необходимо помнить о следующих:
• пробой изоляции, особенно вблизи опор шин и втычных контактов выдвижных частей НКУ (75 % случаев);
• перенапряжения, вызываемые разрушительными электрическими разрядами между точками с минимальными зазорами (15 % случаев);
• конструктивные дефекты аппаратуры (10 % случаев).
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
Русско-английский словарь нормативно-технической терминологии > "дуговая" неисправность
-
89 а пока
•We shall revert to this subject in a later paragraph; for the moment we assume that...
•We will learn how to develop such equations in the next chapter; for now, we may rely on a set of tabulated equations given in Appendix .
•The rms speed is different from... ; for the present, the value of √u will be taken as indicative of...
•For the time being, draw all plate boundaries as single lines, without any distinction as to the type of boundary each represents.
* * *А пока -- in the meantime (тем временем); as long as (до тех пор, пока)Small-scale corrosion tests will be required to define the first stage corrosion rate. In the meantime, initial design will include coated tubes and corrosion resistant metals.Русско-английский научно-технический словарь переводчика > а пока
-
90 аналогичный
•This is something akin to the previously described model.
•To have analogy to (or with)...
•Kindred pumping services are grouped together wherever possible with a common driving unit.
•Like atoms are at minimum separations.
•Later trials subjected glucose to like temperatures.
•Related work on two-photon ionization of NA2 and BaCl beams was carried out by...
•Related bimolecular reactions show the same result.
•A related explanation has been advanced for...
•Elements with similar (or analogous) properties...
•Another suggestion along similar lines is that...
* * *Аналогичный -- similar (to), parallel, related, analogous, likeThe data, which is similar to that due to J., show that the value of u/v near the wall rises rapidly to a maximum.The only requirement for wiring multi-drop devices is that all like terminals be tied together.It is interesting to note that a parallel disagreement exists among physical chemists concerning the appropriate contact angle of water on a clean, gold surface.Русско-английский научно-технический словарь переводчика > аналогичный
-
91 больше
•This was 0.1% above the true value.
•Saturated hydrocarbons absorb only very high energy radiation, usually beyond 160 nm.
•Over (or In excess of, or More than) 50 kilos...
* * *Больше -- greater, higher, more; better Больше на (15 -- 25%)-- The measured torque of all the arched bearing was 15 to 25 percent higher in every case than that of the conventional bearing.—вынуждает больше полагаться наРусско-английский научно-технический словарь переводчика > больше
-
92 весьма ценно для
•Of considerable value to industry is that all the motors can...
Русско-английский научно-технический словарь переводчика > весьма ценно для
-
93 всё же
•When symptoms do occur, they are usually mild.
•Although... is still in its infancy, it does have exciting analytical potential for...
* * *Всё же -- still, yet; though (однако), nevertheless, nonetheless (тем не менее)While existing evidence is confirmatory, these conditions still require experimental verification.Yet a computed bearing power loss value must include all these factors if it is to be used with confidence.This is certainly somewhat misleading, though, since surfaces as smooth as these are quite exceptional.Their theories considered rather simple models of compressors, but nonetheless revealed the principal physics involved.Русско-английский научно-технический словарь переводчика > всё же
-
94 выражаться
. даваться•The orientation of the molecule is expressed by the polar angular coordinates.
•The rate of effusion is expressed in terms of molecules per unit time per unit effusion hole area.
* * *Выражаться -- to be expressed; to manifest itself, to have the effect (проявляться) Выражаться в-- All but the data of K. [...] involve end mounting effects that have the effect of raising qmin above its true value. (... испытывают влияние концевых креплений, выражающееся в повышении...)Русско-английский научно-технический словарь переводчика > выражаться
-
95 выше
•Efficiency is better than 96% at full load.
•If the pressure is above (or higher than, or over) 3 mm,...
•When heating is continued beyond 1403°C the gamma iron changes to delta iron.
••Temperatures upwards of 50 million degrees are required.
II•In the reactions described above (or in the above-described reactions)...
•The coefficients DAB and DAM employed in the foregoing (or above, or previously) are the common mutual diffusion coefficients.
•Water production above a given point on the river...
* * *Выше -- above, beyond, higher, in excess of, plus, upwardsCooling fans and thermocouple reader were timed to switch on and remain so as long as the furnace temperature was above 100oC.As the heat flux increased beyond this value, additional sites became active.The water-cooled combustor operating with preheated air produces combustion gas products at temperatures in excess of 4600° F.We would like to know if you have done or have contemplated doing any higher speed work (e.g. 10,000 plus rpm). (... например, выше 10 000 об/мин)There is no reason why this type of apparatus should not work at 10,000 rpm and upwards.Выше на (15-25%)-- The measured torque of all the arched bearings was 15 to 25 percent higher in every case than that of the conventional bearing.—выше наРусско-английский научно-технический словарь переводчика > выше
-
96 а пока
•We shall revert to this subject in a later paragraph; for the moment we assume that...
•We will learn how to develop such equations in the next chapter; for now, we may rely on a set of tabulated equations given in Appendix .
•The rms speed is different from... ; for the present, the value of √u will be taken as indicative of...
•For the time being, draw all plate boundaries as single lines, without any distinction as to the type of boundary each represents.
Русско-английский научно-технический словарь переводчика > а пока
-
97 весьма ценно для
•Of considerable value to industry is that all the motors can...
Русско-английский научно-технический словарь переводчика > весьма ценно для
-
98 из
•Out of numbered objects a1, a2,... , an, one object may be chosen in ways.
•Of all the possible conformations, we can distinguish two general types.
•One ten growth layers has actual diagnostic value.
•Among the 40 tubes, only a few are high-vacuum rectifiers.
•The vessel is fabricated steel.
•It is evident the curve that...
•The core is fabricated of aluminium-nickel alloy.
•Of these three elements, Cd is the most effective.
Русско-английский научно-технический словарь переводчика > из
-
99 обычный
•The standard enthalpies of some common compounds...
•Using either conventional or laser excitation sources...
•With the advent of new engineering techniques, X-ray diffraction has become a commonplace tool for studies of...
•This phenomenon is rather common in plants.
•Customary (or Conventional) techniques can be...
•Ordinary paint is of little value in...
•The new product outperforms regular lubricants.
•The automatic press embodies all the regular features of the semi-automatic press plus...
•The usual practice is...
•Русско-английский научно-технический словарь переводчика > обычный
-
100 проверять
•It can be easily verified that Eq. (15-29) reduces to Eq. (15-28) when...
•The level of radioactivity is carefully monitored.
•In this way a check on the accuracy of the gauge-glass reading is made.
•The magnetic field was checked against that of a permanent magnet.
•The pressure recorded was checked periodically against a water manometer.
••To keep check on the angle of bend,...
•The interior of the boiler should be examined for tools that might have been left inside.
•Steam lines should be examined frequently for corrosion.
•The crankcase should be inspected for excessive gases.
•To test these conclusions, we carried out several experiments.
•The above theory was tested by results of three experiments.
•This formula permits verification of the value of .
Русско-английский научно-технический словарь переводчика > проверять
См. также в других словарях:
Value investing — is an investment paradigm that derives from the ideas on investment and speculation that Ben Graham David Dodd began teaching at Columbia Business School in 1928 and subsequently developed in their 1934 text Security Analysis . Although value… … Wikipedia
value added — is the risk adjusted return generated by an investment strategy: the return of the investment strategy minus the return of the benchmark. Bloomberg Financial Dictionary * * * Ⅰ. value added UK US (also value added) noun … Financial and business terms
value — The importance placed on something by an individual. Value is subjective and may change according to the circumstances. Something that may be valued highly at one time may be valued less at another time. The CENTER ONLINE Futures Glossary * * * ▪ … Financial and business terms
value — The utility of an object in satisfying, directly or indirectly, the needs or desires of human beings, called by economists value in use, or its worth consisting in the power of purchasing other objects, called value in exchange. Joint Highway… … Black's law dictionary
All Ordinaries — Established in January 1980, the All Ordinaries (colloquially, the All Ords ; also known as the All Ordinaries Index, AOI) is the oldest index of shares in Australia, so called because it contains nearly all ordinary (or common) shares listed on… … Wikipedia
Value at risk — (VaR) is a maximum tolerable loss that could occur with a given probability within a given period of time. VaR is a widely applied concept to measure and manage many types of risk, although it is most commonly used to measure and manage the… … Wikipedia
Value Line — Value Line, Inc.(NASDAQ|VALU), is a New York corporation founded in 1931 by Arnold Bernhard, best known for publishing the The Value Line Investment Survey , a stock analysis newsletter that s updated weekly and kept by subscribers in a large… … Wikipedia
Value capture — refers to a type of innovative public financing in which increases in private land values generated by a new public investment are all or in part “captured” through a land related tax to pay for that investment or other public projects. Value… … Wikipedia
Value theory — encompasses a range of approaches to understanding how, why and to what degree people should value things; whether the thing is a person, idea, object, or anything else. This investigation began in ancient philosophy, where it is called axiology… … Wikipedia
Value engineering — is a systematic method to improve the value of goods and services by using an examination of function. Value, as defined, is the ratio of function to cost. Value can therefore be increased by either improving the function or reducing the cost. It … Wikipedia
Value menu — A selection of value menu hamburgers from McDonald s, Burger King, Sonic Drive In and Wendy s. A value menu is a group of items on a fast food restaurant menu that are designed to be the least expensive items available. In the US, the items are… … Wikipedia